When the DM CPU drivers are active, printing information about a CPU
should be delegated to a matching driver.
Hence, add a static print_cpuinfo that implements this delegation when
DM CPU drivers are active.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Changed condition to CONFIG_IS_ENABLED(CPU):
Signed-off-by: Simon Glass <sjg@chromium.org>
To print the reset status during boot, add a method print_resetinfo to
board_f, which is called in init_sequence_f[], that gets the reset
information from the sysreset driver (assuming there is only one seems
reasonable), and prints it.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
It's useful to have the reset status of the SoC printed out during reset
(e.g. to learn whether the reset was caused by software or a watchdog).
As a first step to implement this, add a get_status method to the
sysreset class, which enables the caller to get printable information
about the reset status (akin to get_desc in the CPU uclass).
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Sandbox is not a real bootloader and it does require
a position independent code to be supported.
Thus, build it with -fPIC explicitly.
Fixes: 16940f720f9b ("Makefile: Don't generate position independent code")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reported-by: Simon Glass <sjg@chromium.org>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
On a
u32 val = __sw32(*addr);
multiple memory accesses are not welcome, since "addr" may
be an IO peripheral register address.
This patch changes __sw16/32 to perform a single memory
access for the source value.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
The Gen2 TMU is fed with fixed 32.5 MHz signal from CP .
This is then divided by 4 in TMU. Fix the timer clock
setting in Gen2.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Replace those two functions with generic ones by defining the
timer macros in include/config/*.h .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The code uses all in all three TMU registers, drop the massive
register layout structures and just define the required timer
registers and use them throughout the code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The header contains only the TMU register layout, just inline it
into the TMU timer implementation and drop the header completely.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The R-Car Gen2 feeds the TMU with CONFIG_SYS_CLK_FREQ / 2,
while the old SH parts use CONFIG_SYS_CLK_FREQ directly.
Just put this into the TMU implementation and drop the
CONFIG_SH_TMU_CLK_FREQ config option.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
These functions are always called for timer = 0, so drop the
timer check. Since these functions are called from one place
only and they are reduced to one line of code, just inline
them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The tmu_bit value evaluates to (ffs(4) >> 1) - 1 = (3 >> 1) - 1 = 0.
Just drop the tmu_bit completely as well as CONFIG_SYS_TMU_CLK_DIV.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This constant is always 4 , for all boards that exist. Define it
once in arch/sh/lib/time.c and remove it from the configs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Drop the macro as it is never used and it collides with sh_eth.h macros.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Drop the macro as it is defined in sh7723.h already.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add vbus-supply regulator support.
On some board vbus is not controlled by the phy but by
an external regulator.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The dtb should be embedded in the u-boot-spl image so that
the CONFIG_SPL_TARGET of spl/u-boot-spl.hex includes it.
This also affects the main u-boot image, so adjust
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME to u-boot.img which now
also includes the dtb.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Incorrect type of size variable results in 0 being
returned for sdram sizes greater than or equal to
4GB.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Stratix10 combines the u-boot-spl image into the fpga configuration
bitstream so that the SDM can load the processors memory. This
process requires a hex format of the u-boot-spl image.
CONFIG_SPL_TARGET is set to "spl/u-boot-spl.hex"
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Some devices, namely Intel's stratix10 SoC, require u-boot-spl in
a hex format. This patch adds spl/u-boot-spl.hex as a possible
target.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Add code to reset all reset signals as in gpio DT node. A reset property
is an optional feature, so only print out a warning and do not fail if a
reset property is not present.
If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Enabled get_function support for dwapb where the function will
return the state of GPIO port.
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
I just stumbled over some cluttered UBIFS messages. It seems some
newline chars are missing in the current U-Boot UBI source.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Last user of this driver went away in May 2017, in
commit eb5ba3aefd ("i2c: Drop use of CONFIG_I2C_HARD")
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
