Commit graph

17090 commits

Author SHA1 Message Date
Bo Shen
f7fa2f3740 arm : Atmel : add at91sam9x5ek board support
Add at91sam9x5ek board support, this board support the following SoCs
  AT91SAM9G15, AT91SAM9G25, AT91SAM9G35, AT91SAM9X25, AT91SAM9X35

Using at91sam9x5ek_nandflash to configure for the board
Now only supports NAND with software ECC boot up

Signed-off-by: Bo Shen <voice.shen@atmel.com>
[move MAINTAINERS entry to right place]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-09-01 14:58:14 +02:00
Andreas Bießmann
963333e92c doc/git-mailrc: update at91 and avr32
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-09-01 14:58:14 +02:00
Ilya Yanok
c44080b224 am335x_evm: enable SMSC PHY driver
Beaglebone uses SMSC PHY which works incorrectly with generic PHY
driver so enable SMSC PHY driver to fix networking problems on
Beaglebone.

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-09-01 14:58:14 +02:00
Enric Balletbò i Serra
4833b0939a OMAP3: fix DRAM size for IGEP-based boards.
The total RAM size of the IGEP-based boards is 512MiB not 1GiB, the
LPDDR memory consist on two dies of 256MiB.

Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
2012-09-01 14:58:14 +02:00
Laurence Withers
be7d257895 DaVinci DA8xx: fix set_cpu_clk_info()
For the DA8xx family of SoCs, the set_cpu_clk_info() function was not
initialising the DSP frequency, leading to 'bdinfo' command output such as:

  [...snip...]
  ARM frequency = 300 MHz
  DSP frequency = -536870913 MHz
  DDR frequency = 300 MHz

This commit provides a separate implementation of set_cpu_clk_info() for
the DA8xx SoCs that initialises the DSP frequency to zero (since
currently the DSP is not enabled by U-Boot on any DA8xx platform). The
separate implementation is justified because there is no common code
between DA8xx and the other SoC families. It is now much easier to
understand the flow of the two separate functions.

Signed-off-by: Laurence Withers <lwithers@guralp.com>
Cc: Tom Rini <trini@ti.com>
Cc: Hadli, Manjunath <manjunath.hadli@ti.com>
Cc: Heiko Schocher <hs@denx.de>
2012-09-01 14:58:14 +02:00
Laurence Withers
de9d2e3d60 DaVinci DA8xx: replace magic number for DDR speed
Replace a magic number for the DDR2/mDDR PHY clock ID with a proper
definition. In addition, don't request this clock ID on DA830 hardware,
which does not have a DDR2/mDDR PHY (or associated PLL controller).

Signed-off-by: Laurence Withers <lwithers@guralp.com>
Cc: Tom Rini <trini@ti.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
2012-09-01 14:58:14 +02:00
Laurence Withers
88ac6b9d14 DaVinci DA850: UART2 clock ID comes from ASYNC3
On the DA830, UART2's clock is derived from PLL controller 0 output 2.
On the DA850, it is in the ASYNC3 group, and may be switched between PLL
controller 0 or 1. Fix the definition of the ID to match.

Signed-off-by: Laurence Withers <lwithers@guralp.com>
Cc: Tom Rini <trini@ti.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
2012-09-01 14:58:14 +02:00
Laurence Withers
8a54aa0da7 DaVinci DA8xx: tidy up clock ID definition
Tidy up the clock IDs defined for the DA8xx SOCs. With this new structure in
place, it is clear how to define new clock IDs, and how these map to the
numbers presented in the technical reference manual.

Signed-off-by: Laurence Withers <lwithers@guralp.com>
Cc: Tom Rini <trini@ti.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Tom Rini
3bc78d7e76 doc/git-mailrc: Update 'ti' alias
Remove Sandeep, thanks for all the hard work!

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Marek Vasut
308252adaf dm: Move OMAP GPIO driver to drivers/gpio/
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Marek Vasut
16e41c857c dm: Select CONFIG_SPL_GPIO_SUPPORT on OMAP
This fixes the breakage with SPL on most OMAP boards after the GPIO
driver was moved.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Tom Rini
db7dd8109c am33xx: Rework pinmux functions
- Move definition of the EEPROM contents to <asm/arch/sys_proto.h>
  - Make some defines a little less generic now.
- Pinmux must be done by done by SPL now.
- Create 3 pinmux functions, uart0, i2c0 and board.
- Add pinmux specific to Starter Kit EVM for MMC now.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Tom Rini
726c05d2cf am33xx evm: Add CONFIG_CMD_EEPROM and related
am33xx boards have at least one eeprom and in the case of beaglebones
with capes, more.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Tom Rini
65d750be59 am33xx: Add support for TI AM335x StarterKit EVM
- Board requires gpio0 #7 to be set to power DDR3.
- Board uses DDR3, add a way to determine which DDR type to call
  config_ddr with.
- Both of the above require filling in the header structure early, move
  it into the data section.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Tom Rini
973b663820 am33xx: Remove board/ti/am335x/evm.c
The intention has always been (and boards are to support) an i2c EEPROM
that will identify what hardware they are, allowing a single binary to
support multiple boards.  As such, remove the 'evm.c' file as there is
nothing EVM centric in it currently, only SoC peripheral configuration.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Tom Rini
d4898ea896 am33xx: Add DDR3 (Micron MT41J128M16JT-125) timings and support
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Tom Rini
318f27c98f am33xx: Rework config_ddr to make DDR3 support easier.
In order to support DDR3 as well as DDR2, we need to perform the same
init sequence, but with different values.  So change config_ddr() to
toggle setting pointers/etc for what DDR2 wants, and then calling.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Tom Rini
942d3f0174 am33xx: Move some variables in emif4.c, mark them static.
We need vtpreg and ddrctrl but no longer need a second ddrregs.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Tom Rini
a74f0c7cb5 am33xx: Correct and clean up ddr_regs struct
The ddr_regs struct was incorrectly offset after the dt0wiratio0 entry.
Correct this by documenting a missing register that will be used at some
point in the future (when write leveling is supported).  Further, the
cmdNcs{force,delay} fields are undocumented and we have been setting
them to zero, remove.  Next, setting of the
'DATAn_REG_PHY_USE_RANK0_DELAYS field belongs with the rest of the
ddr_data entries, so program it there.  Finally, comment on how we are
configuring the DATA1 registers that correspond to the DATA0 (dt0)
registers defined in the struct.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Tom Rini
82afcc9efd am33xx: Do not touch 'ratio1' fields
The various ratio1 fields are not documented in any of the documentation
I can find.  Removing these and testing has yielded success, so remove
the code that sets them and move their locations into the reserved
fields.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
5ac3b7ada1 am33xx: Rework config_io_ctrl slightly
This function sets a number of related registers to the same value (the
registers in question all have the same field descriptions and are
related in operation).  Rather than defining a struct and setting the
value repeatedly, just pass in the value.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
ff7ec0f945 am33xx: Use emif_regs struct for storing initialization values
Rather than defining our own structs to note what to use when
programming the EMIF and related re-use the emif_regs struct.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
87a1acbb69 am33xx: Turn a number of 'int' functions to 'void'
A number of memory initalization functions were int and always returned
0.  Further it's not feasible to be doing error checking here, so simply
turn them into void functions.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
c48c895433 am33xx: Document what we're doing with ddrctrl->ddrckectrl
- Remove the call to set ddrctrl->ddrioctrl as it's all zeros.
- Comment what we're really setting in ddrctrl->ddrckectrl which is that
  we're operating in the normal mode where EMIF/PHY clock is controlled
  by the PHY.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Vaibhav Bedia
7d8a961d31 am335x: ddr_defs: Update EMIF parameters
EMIF parameters are calculated based on the AC timing
parameters from the SDRAM datasheet and the DDR frequency.

Current values for these paramters in AM335x U-Boot code,
though reliable, are not fully optimal. The most optimal
settings can be derived based on the guidelines published
at [1]. A pre-computed set of values with the most optimum
settings for AM335x EVM and BeagleBone can be found at [2].

[1] http://processors.wiki.ti.com/index.php/AM335x_EMIF_Configuration_tips
[2] http://processors.wiki.ti.com/index.php/OMAP_and_Sitara_CCS_support#AM335x

Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
c8da4a587c am33xx: Clean up unused DDR defines, prefix more with 'DDR2'
- Remove a handful of unused defines.
- Prefix more values with 'DDR2' as DDR3 will require different values.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
b971dfad6a am33xx: Move the call to ddr_pll_config, make it take the frequency
Depending on if we have DDR2 or DDR3 on the board we will need to call
ddr_pll_config with a different value.  This call can be delayed
slightly to the point where we know which type of memory we have.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
fda35eb982 am33xx: Pass to config_ddr the type of memory that is connected
We need to pass in the type of memory that is connected to the board.
The only reliable way to do this is to know what type of board we are
running on (which later will be knowable in s_init()).  For now, pass in
the value of DDR2.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
bce58fece5 am33xx: Make config_cmd_ctrl / config_ddr_data take const structs
Rework the EMIF4/DDR code slightly to setup the structs that
config_cmd_ctrl and config_ddr_data take to be setup at compile time and
mark them as const.  This lets us simplify the calling path slightly as
well as making it easier to deal with DDR3.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
10e7e36daf am33xx: Rework DDR2 EMIF initalization slightly
With the previous bugfix we now don't need to set two different REF_CTRL
values and instead set the final value.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
372f11f58d am33xx: Bugfix to config_sdram()
When we change SDRAM_CONFIG this triggers a refresh based on all of the
parameters that we have programmed so we must do this last.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
13f1c44bc5 am33xx: Remove extra check in enable_ddr_clocks
We do not need to check for EMIF_GCLK and L3_GCLK being active.  This
was a hold-over from bringup and no longer required.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:12 +02:00
Tom Rini
7d5eb34908 am33xx: Convert to using <asm/emif.h> to describe the EMIF
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:11 +02:00
Tom Rini
79b3e6b75b am33xx: Remove DMM_BASE define
The am33xx does not have a DMM, so don't define the base.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:11 +02:00
Tom Rini
7bf038ec21 am335x_evm: Update config for common usage
- Add default commands
- Add HUSH parser
- Make environment, malloc areas larger
- Add ATAGS and OF_LIBFDT
- Add defaults to boot ramdisk and MMC, use uEnv.txt

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:11 +02:00
Tom Rini
a438c756b6 am33xx: Enable gpio0 clock
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:11 +02:00
Javier Martinez Canillas
d271a61141 OMAP3: igep00x0: add SPL support for IGEP-based boards
This patch adds SPL support for IGEP-based boards.
Tested on an IGEPv2 Rev.C board with Micron NAND Flash memory.

Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
2012-09-01 14:58:11 +02:00
Javier Martinez Canillas
41708a5db4 OMAP3: mem: Add Numonyx OneNAND 200MHz timing information
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
2012-09-01 14:58:11 +02:00
Javier Martinez Canillas
ca511cfb2a OMAP3: igep00x0: Add config option to choose flash storage memory
IGEP-based boards can have two different flash memories, a OneNAND or a
NAND device. Add a configuration option for to choose which memory to use.

Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
2012-09-01 14:58:11 +02:00
Chandan Nath
9304296044 am335x_evm: CPSW support
This patch adds board-specific initialization for CPSW on
TI AM335X based boards. Tested on BeagleBone.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
[Ilya: split board-specific part into separate patch]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-09-01 14:58:11 +02:00
Ilya Yanok
c59a6a0dac am335x_evm: read the on-board EEPROM
Read the on-board EEPROM during startup to detect the version
of the board we are running on (as for now only BeagleBone vs
EVM detection is supported).

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-09-01 14:58:11 +02:00
Chandan Nath
89017e150e am33xx: pin mux defintions for CPSW switch
This patch adds pin mux settings for CPSW switch found on
TI AM335X based boards (MII and RGMII modes).

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
[Ilya: split pinmux into separate patch]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-09-01 14:58:11 +02:00
Chandan Nath
e79cd8eb9b am33xx: CPSW init and definitions
This patch adds platform-specific initialization for CPSW
switch on TI AM33XX SoCs.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
[Ilya: split init out of original patch]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-09-01 14:58:11 +02:00
Cyril Chemparathy
2b62997ce9 cpsw: add driver for cpsw ethernet device
CPSW is an on-chip ethernet switch that is found on various SoCs from Texas
Instruments.  This patch adds a simple driver (based on the Linux driver) for
this hardware module.

This patch also adds support to clean and flush dcache during packet send
and receive.

Changes by Sandhya: Added support to clean and flush dcache during packet
		    send/receive and added timeouts.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com>
[Ilya: Cleaned cache handling, some style cleanup, some small
fixes, use of internal RAM for descriptors]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-09-01 14:58:10 +02:00
Peter Meerwald
2c30c18487 beagle: only call DSS code when #defined CONFIG_VIDEO_OMAP3
Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
2012-09-01 14:58:10 +02:00
Mikhail Kshevetskiy
99b603e714 serial/ns16550: ns16550 has a different register layout on SOC_DA8XX
also fix NS16550_init() as we need 16x divider

Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Acked-by: Sughosh Ganu <urwithsughosh@gmail.com>
Tested-by: Sughosh Ganu <urwithsughosh@gmail.com>
2012-09-01 14:58:10 +02:00
Mikhail Kshevetskiy
680866a502 arm/davinci/da850: add uart0 pinmux
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Tested-by: Sughosh Ganu <urwithsughosh@gmail.com>
2012-09-01 14:58:10 +02:00
Mikhail Kshevetskiy
89473d233f arm/davinci: fix DDR2/mDDR memory controller initialization for Omap L138
follow section 15.2.13.1 (Initializing Following Device Power Up or Reset) of
OMAP-L138 DSP+ARM Processor Technical Reference Manual

Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
2012-09-01 14:58:10 +02:00
Albert ARIBAUD
c50afc1dab Revert "arm: armv7: add compile option -mno-unaligned-access if available"
This reverts commit 5347560f5427bcdd48a563b62180481606ac8044,
which was applied only to get release 2012.07 functional on as
many ARM targets as possible despite mis-aligned accesses.
2012-09-01 14:58:10 +02:00
Steve Sakoman
d3decdebde omap: am335x_evm: enable i2c1 channel
This patch sets up pinmux, enables fclk, and
defines CONFIG_I2C_MULTI_BUS

Signed-off-by: Steve Sakoman <steve@sakoman.com>
2012-09-01 14:58:10 +02:00