CPG IP in some specific Renesas SoCs (i.e. new R8A779A0 V3U SoC)
requires a different setting procedure. Make struct cpg_mssr_info
accessible to handle the clock setting in that case.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The MODEMR register offset changed on R8A779A0, make the MODEMR offset
configurable. Fill the offset in on all clock drivers. No functional
change.
Based off "clk: renesas: Make CPG Reset MODEMR offset accessible from
struct cpg_mssr_info" by Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This supports RPCD2 clock handling. While at it, add the check point
for RPC-IF clock RPCD2 Frequency Division Ratio, since it must be odd
number
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This patch fixes Realtime Module Stop Control Register (RMSTPCR) offsets
based on R-Car Gen3, H2/M2/M2N/E2/E2X hardware user's manual.
The r8a73a4 only has RMSTPCR0 - RMSTPCR5 so this calculation change
doesn't affect it.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reinstate RPC clock on D3/E3 after Linux 5.12 synchronization.
The D3 and E3 clock drivers do not contain RPC clock entries
mainline Linux yet.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
ZynqMP:
- Syncup DT with Linux kernel
- Fix mmc mini configurations via DT
- Add pinctrl/psgtr description to DTs
- Add DTs for Kria boards
- Enable RTC and Time commands
Versal:
- Fix early BSS section location
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYKTbXAAKCRDKSWXLKUoM
IYV+AKCeHWADR2nP2jPPByI5YdmQWMez8gCeLSgLiVak7Its1c/uE0h4izQvGbE=
=j5p2
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.07-rc3' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.07-rc3
ZynqMP:
- Syncup DT with Linux kernel
- Fix mmc mini configurations via DT
- Add pinctrl/psgtr description to DTs
- Add DTs for Kria boards
- Enable RTC and Time commands
Versal:
- Fix early BSS section location
Right now U-Boot is not aware about date/time that's why enable it by
default also with EFI runtime service for setting time.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
U-Boot expects to be linked to a specific hard-coded address and to
be loaded to and run from that address. CONFIG_POSITION_INDEPENDENT
config lifts that restriction & allowing the code to be loaded to
and executed from almost any address.
As we enabled CONFIG_POSITION_INDEPENDENT, CONFIG_INIT_SP_RELATIVE
is enabled by default, where it will set the early stack pointer at
runtime by adding an offset value to &_bss_start. The offset value
is taken from SYS_INIT_SP_BSS_OFFSET.
SYS_INIT_SP_BSS_OFFSET offset should be large enough so that the
early malloc region, global data (gd), and early stack should fit.
With commit d8fabcc424bd ("arm64: versal: Increase SYS_MALLOC_F_LEN")
SYS_MALLOC_F_LEN is increased from 32KB to 1MB, so we need to
accommodate this space with SYS_INIT_SP_BSS_OFFSET. Hence increasing
SYS_INIT_SP_BSS_OFFSET to 1.5MB.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Acked-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch contains several DT files for SOM platform.
Carrier card is sck-kv (KV260) revA/B. SMK-K26 is description for starter
kit which doesn't have EMMC populated. And SM-K26 is full som with EMMC.
Files are divided in this way to make sure that SOM can be plugged to
different carrier card and all peripherals on SOM (or defined by a spec) can
be used by U-Boot. Full DT for SOM+CC can be merged together as overlays.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mainline kernel has psgtr driver that's why it is good to add description
to DT files. Some boards are just missing description for USB3 and sata.
zc1751-dc1 and p-a2197 are also missing clock descriptions for input
clocks.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP pinctrl Linux driver has been merged to 5.13-rc1 kernel. Based on it
DT files can be extended by pinctrl configurations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Probe zynqmp firmware driver by adding zynqmp firmware, power &
ipi mailbox device tree nodes for mini emmc.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Add missing xlnx,mio-bank property to sdhci node. Also add properties with
0 value to have it listed in case that files are copied to different
projects where default case doesn't need to be handled in the same way.
That's why explicitly list them too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
I2C muxes that have the slave devices with same address are
falling into the below problem.
VCK190 system controller (SC) - zynqmp-e-a2197-00-revA.dts
I2C1 (0xff030000) -> Mux1 (@0x74) -> Channel 3 -> 0x50
I2C1 (0xff030000) -> Mux2 (@0x75) -> Channel 0 -> 0x50
1. SC accesses I2C1 - Mux1 (0x74) - Channel 3 and then
2. SC accesses I2C1 - Mux2 (0x75) - Channel 0.
Now it results in 2 slave devices with same address (0x50)
on the I2C bus, making the communication un-reliable.
When ' i2c-mux-idle-disconnect' is in DT, after '1', the Mux
channel output is disconnected, making none of the channels
available to the I2C1. So, there is no question of having the
same addressed slave (0x50) present on the bus when we are doing '2'.
Same pattern is seen in below two boards also.
ZCU208 - zynqmp-zcu208-revA.dts
ZCU216 - zynqmp-zcu216-revA.dts
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Add label to GPIO lines so the user-level applications can find any line
without knowing its physical path on System Controller on VCK190/VMK180.
These labels are describing EMIO gpio connection which depends on PL which
we normally don't describe but that's only way to go for now. Lately this
should be done out of this source code.
Signed-off-by: Saeed Nowshadi <saeed.nowshadi@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The 'silabs,skip-recall' property prevents interruption in operation of
the clock while the driver is being probed. Without this property, the
DDR DIMM clk can cause a failure during Versal's boot.
Signed-off-by: Saeed Nowshadi <saeed.nowshadi@xilinx.com>
All si570 which are used for ps reference clock generation should contain
silabs,skip-recall property not to cause break on ps clock.
On Versal boards this will cause hang on Versal cpu when it is booted at
the same time with SC.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Documentation:
* add a man-page for the size command
* add man-page for extension command to index
Bug fixes:
* avoid build failure due to missing SHA512 hardware acceleration
* correct error handling in TCG2 protocol
* don't let user disable capsule authentication
* correct reading directories via UEFI API
-----BEGIN PGP SIGNATURE-----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=h8yY
-----END PGP SIGNATURE-----
Merge tag 'efi-2021-07-rc3' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2021-07-rc3
Documentation:
* add a man-page for the size command
* add man-page for extension command to index
Bug fixes:
* avoid build failure due to missing SHA512 hardware acceleration
* correct error handling in TCG2 protocol
* don't let user disable capsule authentication
* correct reading directories via UEFI API
Build error occurs when CONFIG_EFI_SECURE_BOOT or
CONFIG_EFI_CAPSULE_AUTHENTICATE is enabled,
because hash-checksum.c is not compiled.
Since hash_calculate() implemented in hash-checksum.c can be
commonly used aside from FIT image signature verification,
this commit itroduces HASH_CALCULATE option to decide
if hash-checksum.c shall be compiled.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
EFI_TCG2 depends not only on TPMv2 but also on the underlying algorithms.
So select the missing SHA1, SHA256, SHA384 and SHA512 we currently support
Reported-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add 'default y'.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Up to now we are stopping the EFI subsystem if a TPMv2 exists but the
protocol fails to install. Now that we've switched the config to 'default
y' the sandbox TPM fails, since it doesn't support all the required
capabilities of the protocol.
Not installing the protocol is not catastrophic. If the protocol fails
to install the PCRs will never be extended to the expected values, so
some other entity later in the boot flow will eventually figure it out
and take the necessary actions.
While at it fix a corner case were the user can see an invalid error
message when the protocol failed to install. We do have a tcg2_uninit()
which we call when the protocol installation fails. There are cases though
that this might be called before the configuration table is installed (e.g
probing the TPM for capabilities failed). In that case the user will see
"Failed to delete final events config table". So stop printing it since it's
not an actual failure , simply because the config table was never installed
in the first place.
In order to stop printing it make efi_init_event_log() and create_final_event()
cleanup themselves and only call tcg2_uninit() when the protocol installation
fails.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Instead of just failing, clean up the installed config table and
EventLog memory if logging an s-crtm event fails during the protocol
installation
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Eliminate label 'out:' by using return.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
efi_init_event_log() calls tcg2_uninit() in case of failure.
We can skip that since the function is called on efi_tcg2_register()
which also cleans up if an error occurs
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is same issue as https://bugzilla.redhat.com/show_bug.cgi?id=1733817,
but that fix was wrongly partial reverted.
When reading a directory, EFI_BUFFER_TOO_SMALL should be returned when
the supplied buffer is too small, so a use-case is to call
EFI_FILE_PROTOCOL.Read() with *buffer_size=0 and buffer=NULL to
obtain the needed size before doing the actual read.
So remove the check only for directory reading, file reading already
do the check by itself.
Fixes: db12f518edb0("efi_loader: implement non-blocking file services")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefan Sørensen <stefan.sorensen@spectralink.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The current capsule authentication code checks if the environment
variable capsule_authentication_enabled is set, for authenticating the
capsule. This is in addition to the check for the config symbol
CONFIG_EFI_CAPSULE_AUTHENTICATE. Remove the check for the environment
variable. The capsule will now be authenticated if the config symbol
is set.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviwed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Commit a479f103dc ("hash: Allow for SHA512 hardware implementations")
defined function definitions for hardware accelerated SHA384 and SHA512.
If CONFIG_SHA_HW_ACCEL=y, these functions are used.
We already have boards using CONFIG_SHA_HW_ACCEL=y but none implements the
new functions hw_sha384() and hw_sha512().
For implementing the EFI TCG2 protocol we need SHA384 and SHA512. The
missing hardware acceleration functions lead to build errors on boards like
peach-pi_defconfig.
Introduce a new Kconfig symbol CONFIG_SHA512_HW_ACCEL to control if the
functions hw_sha384() and hw_sha512() shall be used to implement the SHA384
and SHA512 algorithms.
Fixes: a479f103dc ("hash: Allow for SHA512 hardware implementations")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Building 32bit boards with the TCG2 protocol enabled leads to a build
warning due to a missing conversion.
lib/efi_loader/efi_tcg2.c:774:27:
error: cast to pointer from integer of different size
[-Werror=int-to-pointer-cast]
774 | ret = tcg2_create_digest((u8 *)data_to_hash, data_to_hash_len,
| ^
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
'make htmldocs' results in a build warning
checking consistency... doc/usage/extension.rst:
WARNING: document isn't included in any toctree
Add the document to the index.
Fixes: 2f84e9cf06 ("cmd: add support for a new "extension" command")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Versions of U-Boot before 2014.01 created a symlink from include/asm to
the architecture-specific header directory.
If an ARM board is build with that old version, then sandbox is built on
a more recent version (both with in-tree builds), the include/asm symlink
confuses the build system. It picks up the ARM headers when it should be
using the sandbox ones.
Since 2014 U-Boot has only created a symlink inside the include/asm/
directory and only for out-of-tree builds. So for in-tree builds it does
not expect to see an include/asm symlink. It is not removed by
'make mrproper'. It does show up with 'git status' but is easy enough to
miss.
Add include/asm to the files to remove with 'make mkproper'. For recent
U-Boot builds this has no effect, since include/asm is a directory, not a
file. If the include/asm symlink is there, it will be removed.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
s/psci_features/request_psci_features/g for the case when both
ARCH_SUPPORT_PSCI=y and ARM_PSCI_FW=y, that leads to these
compilation issues:
drivers/firmware/psci.c:69:12: error: conflicting types for 'psci_features'
69 | static int psci_features(u32 psci_func_id)
| ^~~~~~~~~~~~~
In file included from drivers/firmware/psci.c:23:
./arch/arm/include/asm/system.h:548:5: note: previous declaration of 'psci_features' was here
548 | s32 psci_features(u32 function_id, u32 psci_fid);
| ^~~~~~~~~~~~~
Tested-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reported-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Fixes: b7135b034f ("psci: add features/reset2 support")
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Python3 taken from the PATH causes build issues when pylibfdt bindings are
generated with Yocto SDK.
Python3 provided as a part of SDK is not compatible with host Python3,
therefore binding build breaks with following errors:
scripts/dtc/pylibfdt/libfdt_wrap.c:154:11: fatal error: Python.h: No such file or directory
154 | # include <Python.h>
| ^~~~~~~~~~
Do not enforce the python3 from the PATH and make it conditionally-assigned
so it can be overridden from outside of build system. Keep the default
assignment to point to version that is taken from the PATH.
Similar fix has been introduced in b48bfc74ee ("tools: allow to override
python"), where conditional assignment is used for python executable to
address similar build errors.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Simon Glass <sjg@chromium.org>
Fixes: e91610da7c ("kconfig: re-sync with Linux 4.17-rc4")
Reviewed-by: Simon Glass <sjg@chromium.org>
- Add base support for Marvell OcteonTX2 CN9130 DB (mostly done
by Kostya)
- Sync Armada 8k MMU setup with Marvell version (misc Marvell
authors)
- spi: kirkwood: Some fixes especially for baudrate generation
(misc Marvell authors)
- mvebu: x530: Reduce SPL image size (Stefan)
- Rename "rx_training" to "mvebu_comphy_rx_training" (Stefan)
Currently all assembly optimized implementation of memory routines
show up at the top level of the RISC-V architecture Kconfig menu.
Let's group them together into a submenu.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present U-Boot SPL fails to boot on SiFive Unleashed board, due
to a load address misaligned exception happens when loading the FIT
image in spl_load_simple_fit(). The exception happens in memmove()
which is called by fdt_splice_().
Commit 8f0dc4cfd1 introduces an assembly version of memmove but
it does take misalignment into account (it checks if length is a
multiple of machine word size but pointers need also be aligned).
As a result it will generate misaligned load/store for the majority
of cases and causes significant performance regression on hardware
that traps misaligned load/store and emulate them using firmware.
The current behaviour of memcpy is that it checks if both src and
dest pointers are co-aligned (aka congruent modular SZ_REG). If
aligned, it will copy data word-by-word after first aligning
pointers to word boundary. If src and dst are not co-aligned,
however, byte-wise copy will be performed.
This patch was taken from the Linux kernel patch [1], which has not
been applied at the time being. It fixes the memmove and optimises
memcpy for misaligned cases. It will first align destination pointer
to word-boundary regardless whether src and dest are co-aligned or
not. If they indeed are, then wordwise copy is performed. If they
are not co-aligned, then it will load two adjacent words from src
and use shifts to assemble a full machine word. Some additional
assembly level micro-optimisation is also performed to ensure more
instructions can be compressed (e.g. prefer a0 to t6).
With this patch, U-Boot boots again on SiFive Unleashed board.
[1] https://patchwork.kernel.org/project/linux-riscv/patch/20210216225555.4976-1-gary@garyguo.net/
Fixes: 8f0dc4cfd1 ("riscv: assembler versions of memcpy, memmove, memset")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
If /chosen was missing, chosen_offset would never get updated with the new
/chosen node. This would cause fdt_setprop_u32 to fail. This patch fixes
this by setting chosen_offset. In addition, log any errors from setting
boot-hartid as well.
Fixes: 5370478d1c ("riscv: Add boot hartid to device tree")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
At present there is only one Kconfig option CONFIG_SIFIVE_CLINT to
control the enabling of SiFive CLINT support in both SPL (M-mode)
and U-Boot proper (S-mode). So for a typical SPL config that the
SiFive CLINT driver is enabled in both SPL and U-Boot proper, that
means the S-mode U-Boot tries to access the memory-mapped CLINT
registers directly, instead of the normal 'rdtime' instruction.
This was not a problem before, as the hardware does not forbid the
access from S-mode. However this becomes an issue now with OpenSBI
commit 8b569803475e ("lib: utils/sys: Add CLINT memregion in the root domain")
that the SiFive CLINT register space is protected by PMP for M-mode
access only. U-Boot proper does not boot any more with the latest
OpenSBI, that access exceptions are fired forever from U-Boot when
trying to read the timer value via the SiFive CLINT driver in U-Boot.
To solve this, we need to split current SiFive CLINT support between
SPL and U-Boot proper, using 2 separate Kconfig options.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
This fixes two minor format issues of the ax25-ae350 reST file.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Even if only USB gadget is defined, dwc3 generic driver enables
a definition and probe/remove functions for host driver.
This enables the definition if USB_HOST is enabled only.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
All newer Allwinner SoCs (since about 2013) miss the CONFIGDATA register
in their MUSB implementation, so they need a quirk to hardcode this.
Currently this quirk depends on listing the SoCs affected in musb_reg.h,
which means that this list needs to grow with every new chip.
Move the quirk feature into Kconfig, next to PIO_ONLY, and change the
default to y (for Allwinner builds), while listing the early
implementations as exceptions.
This fixes USB peripheral operation on some newer SoCs, which were not
explicitly listed before.
Tested on H6, H616, R40 (which were broken before), and also on the H5
and A20, for regressions.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
