Commit graph

48 commits

Author SHA1 Message Date
Patrice Chotard
5cc16d886e board: Add STMicroelectronics STiH410-B2260 support
This is a 96Board compliant board based on STiH410 SoC:
  - 1GB DDR
  - On-Board USB combo WiFi/Bluetooth RTL8723BU
    with PCB soldered antenna
  - Ethernet 1000-BaseT
  - SATA
  - HDMI
  - 2 x USB2.0 type A
  - 1 x USB2.0 type micro-AB
  - SD card slot
  - High speed connector (SD/I2C/USB interfaces)
  - Low speed connector (UART/I2C/GPIO/SPI/PCM interfaces)

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-03-14 20:40:21 -04:00
Michael Kurz
d4363baada ARM: SPI: stm32: add stm32f746 qspi driver
This patch adds support for the QSPI IP found in stm32f7 devices.

Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
2017-01-28 14:04:50 -05:00
Michael Kurz
b20b70fcc0 net: stm32: add designware mac glue code for stm32
This patch adds glue code required for enabling the designware
mac on stm32f7 devices.

Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-01-28 14:04:47 -05:00
Michael Kurz
081de09d49 ARM: stm32: use clock setup function defined in clock.c
Use the clock setup function defined in clock.c instead of setting the
clock bits directly in the drivers.
Remove register definitions of RCC in rcc.h as these are already
defined in the struct in stm32.h

Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
2017-01-28 14:04:45 -05:00
Michael Kurz
bad5188be2 ARM: stm32: cleanup stm32f7 files
Cleanup stm32f7 files:
- use BIT macro
- use GENMASK macro
- use rcc struct instead of macro additions

Add missing stm32f7 register in rcc struct

Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Vikas MANOCHA<vikas.manocha@st.com>
2017-01-28 14:04:43 -05:00
Tom Rini
95d5273303 Revert "stm32: Change USART port to USART6 for stm32f746 discovery board"
Per Vikas' request, the problem this commit is supposed to be solving is
something he doesn't see and further this introduces additional hardware
requirements.

This reverts commit 4b2fd720a7.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-07-21 15:38:13 -04:00
Toshifumi NISHINAGA
4b2fd720a7 stm32: Change USART port to USART6 for stm32f746 discovery board
This change is to remove a halt at about 200KiB
while sending a large(1MiB) binary to a micro controller using USART1.
USART1 is connected to a PC via an on-board ST-Link debugger
that also functions as a USB-Serial converter.
However, it seems to loss some data occasionally.
So I changed the serial port to USART6 and connected it to the PC using
an FTDI USB-Serial cable, therefore the transmission was successfully
completed.

Signed-off-by: Toshifumi NISHINAGA <tnishinaga.dev@gmail.com>
2016-07-14 18:22:44 -04:00
Toshifumi NISHINAGA
25c1b1353c stm32: Add SDRAM support for stm32f746 discovery board
This patch adds SDRAM support for stm32f746 discovery board.
This patch depends on previous patch.
This patch is based on STM32F4 and emcraft's[1].

[1]:  https://github.com/EmcraftSystems/u-boot

Signed-off-by: Toshifumi NISHINAGA <tnishinaga.dev@gmail.com>
2016-07-14 18:22:43 -04:00
Vikas Manocha
e66c49fa93 stm32: add support for stm32f7 & stm32f746 discovery board
This patch adds support for stm32f7 family & stm32f746 board.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
2016-02-24 18:43:57 -05:00
Vikas Manocha
14cec06113 gpio: stm32_gpio: move clock config from driver to board
This patch removes the gpio clock enable from gpio driver & move it in the
board code, making it possible to use the gpio driver with other socs.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
2016-02-24 18:42:49 -05:00
Vikas Manocha
dffceb4b15 serial: serial_stm32: move clock config from driver to board
This patch removes the uart clock enable from serial driver & move it in the
board code.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-02-08 10:10:36 -05:00
Kamil Lulko
665624149a stm32: Convert serial driver to DM
Signed-off-by: Kamil Lulko <kamil.lulko@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-12-12 15:56:08 -05:00
Kamil Lulko
5be9356926 Change e-mail address of Kamil Lulko
Signed-off-by: Kamil Lulko <kamil.lulko@gmail.com>
2015-12-05 18:22:32 -05:00
Simon Glass
0abdd9d01a arm: Remove nhk8815 boards and nomadik arch
These boards have not been converted to generic board by the deadline.
Remove them.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-09-11 14:56:04 -04:00
Antonio Borneo
089fddfde2 stm32f429: pass the device unique ID in DTB
Read device unique ID and set environment variable "serial#".
Value would then be passed to kernel through DTB.

To read ID from DTB, kernel is required to have commit:
3f599875e5202986b350618a617527ab441bf206 (ARM: 8355/1: arch: Show
the serial number from devicetree in cpuinfo)
This commit is already mainline since v4.1-rc1.

Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: Albert Aribaud <albert.u.boot@aribaud.net>
To: Tom Rini <trini@konsulko.com>
To: Kamil Lulko <rev13@wp.pl>
Cc: u-boot@lists.denx.de
2015-07-27 15:02:14 -04:00
Tom Rini
4905dfc65d Merge branch 'master' of git://git.denx.de/u-boot-spi 2015-07-14 14:13:23 -04:00
Antonio Borneo
8379c79917 stm32f4: fix MAINTAINERS file
When "scripts/get_maintainer.pl" parses "board/.../MAINTAINERS",
it uses the line containing board name as delimiter.
Without this line, the script happily mixes the lines from current
board MAINTAINERS file with lines from another file.

Fix it by adding a reasonable board name.

Tested by comparing output of:
	cat board/st/stm32f429-discovery/MAINTAINERS
	./scripts/get_maintainer.pl -f board/st/stm32f429-discovery

Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: u-boot@lists.denx.de
To: Kamil Lulko <rev13@wp.pl>
Cc: Tom Rini <trini@konsulko.com>
2015-07-08 21:51:39 -04:00
Vikas Manocha
54afb50025 stv0991: configure clock & pad muxing for qspi
stv0991 has cadence qspi controller for flash interfacing, this
patch configures the device pads & clock for the controller.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
2015-07-03 13:50:53 +05:30
Vikas Manocha
e0320b746a stv0991: use fdt for serial port platform data
This patch ignores the serial port static platform data at compilation time
in case of device tree control.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-05-10 09:59:37 -04:00
kunhuahuang
60570df19c stm32f4: add serial print port
Add the stm32F4 board's serial ports support.
User can use it easily.
The user only need to edit the number of the usart.
The patch also fix the serial print out.

Last, this version of patch fix the first patch checkpatch.pl error.
Thanks to Kamil Lulko.

Signed-off-by: kunhuahuang <huangkunhua@gmail.com>
2015-05-10 07:29:38 -04:00
rev13@wp.pl
ed09a554be stm32f4: Add support for stm32f429-discovery board
Signed-off-by: Kamil Lulko <rev13@wp.pl>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-04-22 12:14:55 -04:00
Simon Glass
ef48f6dd30 Kconfig: Move CONFIG_DESIGNWARE_ETH to Kconfig
Move this to Kconfig and clean up board config files that use it. Also
rename it to CONFIG_ETH_DESIGNWARE to fit with the naming that exists
in drivers/net/Kconfig.

Signed-off-by: Simon Glass <sjg@chromium.org>
Version 1:
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-04-18 11:11:36 -06:00
Masahiro Yamada
13e55b358e ARM: remove redudant information from Kconfig files
- "string" type for SYS_* is defined in arch/Kconfig
 - SYS_CPU "armv7" has been replaced with "select CPU_V7"
 - SYS_SOC "tegra124" is already defined in tegra124/Kconfig

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
2015-01-12 09:38:47 -05:00
Masahiro Yamada
2decdd088c stv0991: record defconfig ownership in MAINTAINERS
This commit fixes warnings reported by tools/genboardscfg.py.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Vikas Manocha <vikas.manocha@st.com>
Acked-by: Vikas Manocha <vikas.manocha@st.com>
2015-01-12 09:38:47 -05:00
Vikas Manocha
39e4795a79 dm: stv0991: Move serial to driver model
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
2014-12-09 15:16:20 -05:00
Vikas Manocha
2ce4eaf4c8 stv0991: enable ethernet support
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
2014-12-09 15:16:19 -05:00
Vikas Manocha
9fa32b1237 stv0991: Add basic stv0991 architecture support
stv0991 architecture support added. It contains the support for
following blocks
- Timer
- uart

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
[trini: Add arch/arm/cpu/armv7/Makefile hunk]
Signed-off-by: Tom Rini <trini@ti.com>
2014-12-09 15:16:01 -05:00
Masahiro Yamada
461be2f96e kconfig: remove redundant "string" type in arch and board Kconfigs
Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME}
are specified in arch/Kconfig.

We can delete the ones in arch and board Kconfig files.

This commit can be easily reproduced by the following command:

find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e '
/config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ {
    N
    s/\n[[:space:]]*string//
}
'

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-09-13 16:43:55 -04:00
Masahiro Yamada
16e16fdde2 nomadik: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Nomadik board select menu to nomadik/Kconfig.

Move also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="nomadik").

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-08-30 21:22:00 -04:00
Masahiro Yamada
93d4334f7f Add board MAINTAINERS files
We have switched to Kconfig and the boards.cfg file is going to
be removed. We have to retrieve the board status and maintainers
information from it.

The MAINTAINERS format as in Linux Kernel would be nice
because we can crib the scripts/get_maintainer.pl script.

After some discussion, we chose to put a MAINTAINERS file under each
board directory, not the top-level one because we want to collect
relevant information for a board into a single place.

TODO:
Modify get_maintainer.pl to scan multiple MAINTAINERS files.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-07-30 08:48:06 -04:00
Masahiro Yamada
dd84058d24 kconfig: add board Kconfig and defconfig files
This commit adds:
 - arch/${ARCH}/Kconfig
    provide a menu to select target boards
 - board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
    set CONFIG macros to the appropriate values for each board
 - configs/${TARGET_BOARD}_defconfig
    default setting of each board

(This commit was automatically generated by a conversion script
based on boards.cfg)

In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.

But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-07-30 08:48:01 -04:00
Masahiro Yamada
a79854a90f board: arm: convert makefiles to Kbuild style
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Tom Rini <trini@ti.com>
2013-11-01 11:42:12 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Wolfgang Denk
702e6014f1 doc: cleanup - move board READMEs into respective board directories
Also drop a few files referring to no longer / not yet supported
boards.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Jason Jin <jason.jin@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2012-07-29 15:42:02 +02:00
Mike Frysinger
464c79207c punt unused clean/distclean targets
The top level Makefile does not do any recursion into subdirs when
cleaning, so these clean/distclean targets in random arch/board dirs
never get used.  Punt them all.

MAKEALL didn't report any errors related to this that I could see.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-15 22:20:36 +02:00
Alessandro Rubini
afba32bcd6 nhk8815: add support for relocation
This patch defines all the needed symbols in the header file
and removes the now-unused config.mk in board directory.
Changes to board C file as requested.

Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
2011-04-27 19:38:10 +02:00
Alessandro Rubini
cb8948ee52 nhk8815: remove platform.S, which was unused at link time
This source file, which I got by the vendor in their own port,
was not actually executing because lib-based compilation
didn't call lowlevel_init (we have CONFIG_SKIP_LOWLEVEL_INIT).
With the change to object-based linking, an undefined symbol in
this file started hitting in the final link.

Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
2011-04-27 19:38:10 +02:00
Sebastien Carlier
6d8962e814 Switch from archive libraries to partial linking
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils.  As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".

This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.

The name of each former library archive is preserved except for
extensions which change from ".a" to ".o".  This commit updates
references accordingly where needed, in particular in some linker
scripts.

This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols.  Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.

Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
2010-11-17 21:02:18 +01:00
Wolfgang Denk
14d0a02a16 Rename TEXT_BASE into CONFIG_SYS_TEXT_BASE
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.

Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-18 22:07:10 +02:00
Ben Warren
7194ab8095 Convert SMC91111 Ethernet driver to CONFIG_NET_MULTI API
All in-tree boards that use this controller have CONFIG_NET_MULTI
added
Also:
  - changed CONFIG_DRIVER_SMC91111 to CONFIG_SMC91111
  - cleaned up line lengths
  - modified all boards that override weak function in this driver
  - modified all eeprom standalone apps to work with new driver
  - updated blackfin standalone EEPROM app after testing

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-10-04 22:37:03 -07:00
Alessandro Rubini
bb4291e625 arm nomadik: add i2c
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-07-29 09:57:47 +02:00
Alessandro Rubini
f7aa59b29a arm nomadik: allow Nand and OneNand to coexists
The evaluation kit has both Nand and OneNand, both drivers are there
and the two configurations only select a different default for the
jffs partition. This adds the OneNand driver and cleans up storage.

Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
2009-07-06 21:53:06 +02:00
Alessandro Rubini
ee1363f2da arm nomadik: rename board to nhk8815
This is an error in my side in the initial submission: nobody
calls it ""nmdk8815", it's "nomadik hardware kit", nhk8815, instead.

Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
2009-07-06 21:53:00 +02:00
Jean-Christophe PLAGNIOL-VILLARD
10a451cd57 arm: unify linker script
all arm boards except a few use the same cpu linker script
so move it to cpu/$(CPU)

that could be overwrite in following order
SOC
BOARD
via the corresponding config.mk

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-12 20:39:52 +02:00
Detlev Zundel
792a09eb9d Fix e-mail address of Gary Jennejohn.
Signed-off-by: Detlev Zundel <dzu@denx.de>
2009-05-15 22:11:59 +02:00
Trent Piepho
f62fb99941 Fix all linker script to handle all rodata sections
A recent gcc added a new unaligned rodata section called '.rodata.str1.1',
which needs to be added the the linker script.  Instead of just adding this
one section, we use a wildcard ".rodata*" to get all rodata linker section
gcc has now and might add in the future.

However, '*(.rodata*)' by itself will result in sub-optimal section
ordering.  The sections will be sorted by object file, which causes extra
padding between the unaligned rodata.str.1.1 of one object file and the
aligned rodata of the next object file.  This is easy to fix by using the
SORT_BY_ALIGNMENT command.

This patch has not be tested one most of the boards modified.  Some boards
have a linker script that looks something like this:

*(.text)
. = ALIGN(16);
*(.rodata)
*(.rodata.str1.4)
*(.eh_frame)

I change this to:

*(.text)
. = ALIGN(16);
*(.eh_frame)
*(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))

This means the start of rodata will no longer be 16 bytes aligned.
However, the boundary between text and rodata/eh_frame is still aligned to
16 bytes, which is what I think the real purpose of the ALIGN call is.

Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
2009-03-20 22:39:12 +01:00
Alessandro Rubini
d3be1bcae7 Enable Ethernet for Nomadik 8815 Evaluation Kit
This trivially enables Ethernet support in the debug board
by setting up the proper chip select.

Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
2009-02-22 13:40:31 +01:00
Alessandro Rubini
d5254f149d Initial support for Nomadik 8815 development board
The NMDK8815 board is distributed by ST Microelectornics.
Other (proprietary) code must be run to unlock the CPU before
U-Boot runs. doc/README.nmdk8815 outlines the boot sequence.

This is the initial port, with basic infrastructure and
a working serial port.

Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-01-24 18:10:37 +01:00