Enable support to read and display configuration/manufacturing infos
from 4Kbit EEPROM located on SOM board.
Note: CONFIG_DISPLAY_BOARDINFO is automatically selected for ARM arch.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
The single binary version of u-boot for XEA board is used to debrick and
factory programming.
The produced u-boot.sb is a single file, which allows having fully
operational u-boot prompt loaded with imx287 ROM.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The XEA board now supports the DM_SERIAL feature in u-boot.
The SPL is using the SPL_OF_PLATDATA - i.e. NOT SPL_DM_SERIAL to
reduce the overall size of the SPL binary.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
After the re-sync with Linux kernel (v6.0) of the XEA DTS
(SHA1: 7d08ddd09b) the alias
for SPI bus, to which SPI-NOR memory is connected, has changed from
'spi3' to 'spi2'.
To be in sync with current u-boot's xea dts, the default bus number
(which allows running 'sf probe' without any extra parameters given)
has been adjusted.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch adjusts XEA's PMU setup as this board is supposed to be
mainly powered from DCDC_BATT source.
Moreover, in this HW design the VDD_4P2 is not used as well.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
To allow U-Boot to fit within emmc boot partitions move the env from
just under 16MiB to just under 4MiB as some emmc devices used on venice
boards have 4MiB boot partitions. This still leaves plenty of room for
U-Boot.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add GPIO name lookup so that you can act on GPIO's by name vs controller
id:
Before:
u-boot=> gpio input pci_wdis#
GPIO: 'pci_wdis#' not found
Command 'gpio' failed: Error -22
After:
u-boot=> gpio input pci_wdis#
gpio: pin pci_wdis# (gpio 103) value is 1
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This is required to boot a FIT image, otherwise the caam_jr driver is
not initialized and the hash verification fails with the following
error:
Verifying Hash Integrity ... sha256dev_get_priv: null device
CAAM was not setup properly or it is faulty
Signed-off-by: Sergio Prado <sergio.prado@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The imx8mm_beacon SOM has a QSPI part attached to the FSPI controller.
Update the header and spl files to support booting from NOR flash and
add imx8mm_beacon_fspi_defconfig to support this configuration.
Signed-off-by: Adam Ford <aford173@gmail.com>
DM_GPIO depends on GPIO to be enabled but select will cause that DM_GPIO is
selected without GPIO which ends up in compilation error:
undefined reference to `dm_gpio_set_value'
undefined reference to `dm_gpio_get_value'
undefined reference to `dm_gpio_free'
undefined reference to `gpio_request_by_name'
Signed-off-by: Michal Simek <michal.simek@amd.com>
[trini: Fix configs which had relied on these select's]
Signed-off-by: Tom Rini <trini@konsulko.com>
The original names picked for the DT doesn't match Linux's naming scheme
and it was renamed there a while ago. Rename it in U-Boot to allow
easily syncing dts between the two projects.
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
As the serial devices are configured in the device tree, enable
DM_SERIAL in the ls1046afrwy defconfigs.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
As the serial devices are configured in the device tree, enable
DM_SERIAL in the ls1046ardb defconfigs.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
As the serial devices are configured in the device tree, enable
DM_SERIAL in the ls1043ardb defconfigs.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Use of CONFIG_SPL_FIT_SIGNATURE=y cause CONFIG_LEGACY_IMAGE_FORMAT=n as
default, this prevent boot scripts in legacy image format from working
and was an unintended change in the listed fixes commits:
Wrong image format for "source" command
Add CONFIG_LEGACY_IMAGE_FORMAT=y to defconfig for affected boards to
restore support for boot scripts in legacy image format.
Fixes: 3bf8e40807 ("board: rockchip: add Radxa ROCK5B Rk3588 board")
Fixes: cf777572ca ("rockchip: rockpro64: Use SDMA to boost eMMC performance")
Fixes: 6e2b8344d6 ("rockchip: rock-pi-4: Use SDMA to boost eMMC performance")
Fixes: 1bf49d5a4a ("rockchip: rk3566-radxa-cm3-io: Update defconfig")
Fixes: 703c170b40 ("rockchip: rk3568-evb: Update defconfig")
Fixes: 68000f750a ("rockchip: rk3568-rock-3a: Update defconfig")
Fixes: 6fb02589a6 ("rockchip: rk3588-evb: Update defconfig")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Currently, the imx93_evk is configured with CONFIG_ENV_IS_IN_MMC and the
chosen environment offset in the config is 0x400000. Unless the user
programs the associated fuses, this offset is the default secondary boot
image offset used by the i.MX 93 ROM bootloader. With certain
combinations of environmental variables, the CRC and beginning of the
environment can potentially falsely appear as a valid boot image
container header. If the expected "sw_version" offset within this
mistaken boot image container is greater than the primary's, the ROM
bootloader can skip booting of the primary image altogether and attempt
to boot with the content of the environment data. This will then hang
the system.
To fix this, move the environment from 0x400000 to 0x700000 reserving up
to 3 MB at 0x400000 for any actual secondary user image container.
Signed-off-by: Ken Sloat <ken.s@variscite.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add configurations for the Videostrong KII Pro set-top box.
This defconfig is cloned from the WeTek Play2's.
Signed-off-by: Ferass El Hafidi <vitali64pmemail@protonmail.com>
Link: https://lore.kernel.org/r/20230507124109.31778-3-vitali64pmemail@protonmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The AD401 board is the Amlogic A1 SoC reference board
Signed-off-by: Igor Prusov <ivprusov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230505125639.3605-6-ivprusov@sberdevices.ru
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Two conflicting bootcmds were included in the environment.
Streamline to defining the bootcmd only in the env file.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
DM_FLAG_PRE_RELOC flag is added into some drivers
by recent commits such as
1bd790bc4b ("firmware: psci: enable DM_FLAG_PRE_RELOC").
Current SYS_MALLOC_F_LEN of SynQuacer Developerbox platform
is too small, Developerbox will not boot due to lack of
heap memory.
This commit increases the size of heap memory.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Enable the newest features: nvmxip, fwu-metadata and
gpt. Commands to print the partition info, gpt info
and fwu metadata will be available.
Adjust also env boot script the address of the
bootbank with the new gpt layout, and also remove
the not needed kernel address bank0 and bank1
and retrieve function that would test the bank flag
before and now we are getting the info from the fwu
metadata.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
We need to distinguish between boot banks and from which
partition to load the kernel+initramfs to memory.
For that, fetch the boot index, fetch the correspondent
partition, calculate the correct kernel address and
then set the env variable kernel_addr with that value.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reduces the CONFIG_DDR_CACHEABLE_SIZE, the size of DDR mapped cacheable
before relocation, to support DDR with only 256MB because the OP-TEE
reserved memory is located at end of the DDR.
By default the new size of 128MB cacheable memory is enough
in dram_bank_mmu_setup() for early_enable_caches() in arch_cpu_init()
and is correct for DDR size = 256MB.
After relocation the real size of DDR, excluding the no-map reserved
memory, is used after the U-Boot device tree parsing.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The ITS file used to build the images here lists three dtb files as
being used. Today, these are built by the logic that will over-build dtb
files based on SOC/etc symbols being set. To future proof this platform
and be generally correct, we list all 3 of the device trees used here in
OF_LIST.
Cc: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Remove the support of the fastboot "oem format" command for STM32MP15x
boards and removed the associated env variable "partitions".
This command is not required; with fastboot tool, the GPT partition can
be handle with "flash" command in "gpt" target (=CONFIG_FASTBOOT_GPT_NAME),
for example: fastboot flash gpt gpt.bin
This patch avoids to define the GPT partitioning in U-Boot environment,
which is incompatible with planned modifications, for example to
support TF-A firmware update.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The CONFIG_FASTBOOT_USB_DEV is used to select USB OTG controller other
than 0 but it is not the case for STM32MP15 boards; it can be removed
to simplify the STM32MP15 defconfig files.
On STM32MP15x boards, we have only one USB device with instance 0,
so the device is hardcoded arch/arm/mach-stm32mp/cpu.c with
the command "fastboot 0" and this define is not used in config files
(include/configs/stm32mp15_st_common.h).
Fixes: 4633fd51c5 ("stm32mp1: activate FASTBOOT on eMMC")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Disable CMD_MTDPARTS as it's no more needed and it is strongly
encouraged to avoid using this command anymore.
(see comments in ./cmd/Kconfig:2422).
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Copy the fixed partition nodes from U-Boot device tree to Linux kernel
device tree to dynamically configure the MTD partitions.
fdt_copy_fixed_partitions is only based on device tree
and replace the function fdt_fixup_mtdparts based on mtdparts variable;
the variable mtdid and mtdparts are not more required.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add partitions subnode in flash0 and nand nodes for all stm32mp157xx-ev1
boards. Update only the file stm32mp157c-ev1-*u-boot.dtsi, included by
other files stm32mp15*-ev1-*-u-boot.dtsi.
For SCMI variant of device tree used with stm32mp15_defconfig
add partitions needed by TF-A firmware update:
- metadata to save the TF-A information: 2 copy
- fip-a / fip-b: two FIP slots, used for system A/B (seamless) update
- the previous "fsbl" partition with 2 copy of TFA is replaced
by 2 partitions (only one copy in each MTD partition) to simplify
the update: no need to managed this copy on update, need to update the
two partition (skip bad block for NAND)
The offset for ENV partition are also updated in stm32mp15_defconfig
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
With DM_ETH configured by default, complete the Ethernet enablement for
LS1046AFRWY by activating DM_MDIO.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the RAM_ROCKCHIP_LPDDR4 to fix the Pinephone Pro booting.
When the configs were updated in 26f92be07e it somehow broke
the PPP boot process so let's fix it.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
CC: Jagan Teki <jagan@edgeble.ai>
CC: Kever Yang <kever.yang@rock-chips.com>
The board comes with SMSC LAN8710A PHY, enable matching driver.
Enable DM_ETH_PHY in the process to start using DM drivers more.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
---
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Michal Simek <michal.simek@amd.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Add code to support FWU_MULTI_BANK_UPDATE.
The platform does not have gpt-partition storage for
Banks and MetaData, rather it used SPI-NOR backed
mtd regions for the purpose.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Towards enabling FWU and supporting new firmware layout in NOR flash,
make u-boot PIC and adjust uboot env offset in flash.
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Add board code for the R8A77980 V3HSK board.
Add CPLD sysreset driver to the R-Car V3H SK board.
Extracted from a larger patch by Valentine Barshak.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync configs and board code with V3H Condor, squash CPLD driver in]
Add board code for the R8A77970 V3MSK board.
Add CPLD sysreset driver to the R-Car V3M SK board.
Extracted from a larger patch by Valentine Barshak.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync configs and board code with V3M Eagle, squash CPLD driver in]
The Lctech Pi F1C200s (also previously known under the Cherry Pi brand)
is a small development board with the Allwinner F1C200s SoC. This is the
same as the F1C100s, but with 64MB instead of 32MB co-packaged DRAM.
Add a defconfig for this board, enabling the most basic features. This
uses the new 64MB memory map, which avoids the very tight memory map we
use for the 32MB F1C100s board(s).
The devicetree file is already in the tree, courtesy of the previous
Linux repo sync.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This is required for UART boot flow where u-boot.img needs to be
downloaded via YMODEM.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
This platform is currently unmaintained and untested, so remove it.
Further, as it is the only TI816X SoC example, remove related files as
well.
Signed-off-by: Tom Rini <trini@konsulko.com>
In non-combined boot flow for K3, all the firewalls are locked by default
until sysfw comes up. Rom configures some of the firewall for its usage
along with the SRAM for R5 but the PSRAM region is still locked.
The K3 MCU Scratchpad for j721e was set to a PSRAM region triggering the
firewall exception before sysfw came up. The exception started happening
after adding multi dtb support that accesses the scratchpad for reading
EEPROM contents.
The commit changes R5 MCU scratchpad for j721e to an SRAM region.
Old Map:
┌─────────────────────────────────────┐ 0x41c00000
│ SPL │
├─────────────────────────────────────┤ 0x41c40000 (approx)
│ STACK │
├─────────────────────────────────────┤ 0x41c85b20
│ Global data │
│ sizeof(struct global_data) = 0xd8 │
├─────────────────────────────────────┤ gd->malloc_base = 0x41c85bfc
│ HEAP │
│ CONFIG_SYS_MALLOC_F_LEN = 0x70000 │
├─────────────────────────────────────┤ CONFIG_SPL_BSS_START_ADDR
│ SPL BSS │ (0x41cf5bfc)
│ CONFIG_SPL_BSS_MAX_SIZE = 0xA000 │
└─────────────────────────────────────┘ CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX
(0x41cffbfc)
New Map:
┌─────────────────────────────────────┐ 0x41c00000
│ SPL │
├─────────────────────────────────────┤ 0x41c40000 (approx)
│ EMPTY │
├─────────────────────────────────────┤ 0x41c81920
│ STACK │
│ SPL_SIZE_LIMIT_PROVIDE_STACK=0x4000 │
├─────────────────────────────────────┤ 0x41c85920
│ Global data │
│ sizeof(struct global_data) = 0xd8 │
├─────────────────────────────────────┤ gd->malloc_base = 0x41c859f0
│ HEAP │
│ CONFIG_SYS_MALLOC_F_LEN = 0x70000 │
├─────────────────────────────────────┤ CONFIG_SPL_BSS_START_ADDR
│ SPL BSS │ (0x41cf59f0)
│ CONFIG_SPL_BSS_MAX_SIZE = 0xA000 │
├─────────────────────────────────────┤ 0x41cff9fc
│ NEW MCU SCRATCHPAD │
│ SYS_K3_MCU_SCRATCHPAD_SIZE = 0x200 │
└─────────────────────────────────────┘ CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX
(0x41cffbfc)
Fixes: ab977c8b91 ("configs: j721s2_evm_r5: Enable support for building multiple dtbs into FIT")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
[n-francis@ti.com: SRAM allocation addressing diagram]
Signed-off-by: Neha Francis <n-francis@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
K3 devices have runtime type board detection. Make the default defconfig
include the secure configuration. Then remove the HS specific config.
Non-HS devices will continue to boot due to runtime device type detection.
If TI_SECURE_DEV_PKG is not set the build will emit warnings, for non-HS
devices these can be ignored.
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Acked-by: Andrew Davis <afd@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
As the ddr timing info will be saved at the last 16KB of
the OCRAM, spl stack & bss base should be updated to avoid
conflict.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add a static u-boot config for i.MX93 low drive mode support. When
low drive mode is enabled, VDD_SOC is set to 0.75V. Bus clocks,
A55 core clock (900Mhz), DDR clock (1866MTS), and some peripherals
clocks (USDHC/FLEXSPI/PDM/DISP_PIX/CAM_PIX) must decrease to meet
max frequencies in low drive mode.
Also set standby voltage for buck1
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add sfc and flash node to device tree and config options to enable
support for booting from SPI NOR flash on Radxa ROCK 5 Model B.
Similar to RK3568 the BootRom in RK3588 can read all data and look for
idbloader at 0x8000, same as on SD and eMMC.
Use the rksd format and modify the mkimage offset to generate a bootable
u-boot-rockchip-spi.bin that can be written to 0x0 of SPI NOR flash. The
FIT image is loaded from 0x60000.
=> sf probe
SF: Detected mx25u12835f with page size 256 Bytes, erase size 4 KiB, total 16 MiB
=> load mmc 1:1 10000000 u-boot-rockchip-spi.bin
1492992 bytes read in 129 ms (11 MiB/s)
=> sf update $fileaddr 0 $filesize
device 0 offset 0x0, size 0x16c800
1300480 bytes written, 192512 bytes skipped in 11.103s, speed 137694 B/s
The BROM_BOOTSOURCE_ID value read back when booting from SPI flash does
not match the expected value of 3 (SPINOR) used by other SoCs. Instead a
value of 6 is read back, add a new enum value to handle this new
bootsource id.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Eugen Hristev <eugen.hristev@collabora.com>
The phycore-rk3288 SPL binary is reaching the limits of 32KB very often.
Enable CONFIG_LTO to reduce the size of the SPL and make the board more
future proof for changes increasing the SPL size.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
If u-boot is installed on the internal emmc, then this will
allow to boot without failure.
Signed-off-by: Wolfgang Zarre <lxdev12@zirdeon.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3588-rock-5b with new defaults.
Remove the SPL_ROCKCHIP_BACK_TO_BROM=y option, SPL is expected to load
next stage from a FIT image and then jump to next stage not back to
BootRom.
Extend SPL_MAX_SIZE to 0x40000, SPL is loaded to 0x0 and TF-A is loaded
to 0x40000, use the space in between as SPL_MAX_SIZE.
Add config option to include useful gpio cmd.
Remove the CONFIG_NET_RANDOM_ETHADDR=y option, ethaddr and eth1addr is
set based on cpuid read from OTP.
Add CONFIG_SYS_NS16550_MEM32=y to use 32bit access of serial register.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3588-evb with new defaults.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM.
Extend SPL_MAX_SIZE to 0x40000, SPL is loaded to 0x0 and TF-A is loaded
to 0x40000, use the space in between as SPL_MAX_SIZE.
Add config options to include useful gpio and regulator cmd.
Remove the CONFIG_NET_RANDOM_ETHADDR=y option, ethaddr and eth1addr is
set based on cpuid read from OTP.
Remove CONFIG_DEBUG_UART_ANNOUNCE=y to remove debug messages.
Add CONFIG_SYS_NS16550_MEM32=y to use 32bit access of serial register.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Like other Rockchip SoCs, DM_RESET and DM_REGULATOR_FIXED is useful
across RK3588 platform. Select them from arch Kconfig.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add sfc and flash node to device tree and config options to enable
support for booting from SPI NOR flash on Radxa ROCK 3 Model A.
Unlike prior generation SoCs the BootRom in RK3568 can read all data and
look for idbloader at 0x8000, same as on SD and eMMC.
Use the rksd format and modify the mkimage offset to generate a bootable
u-boot-rockchip-spi.bin that can be written to 0x0 of SPI NOR flash. The
FIT image is loaded from 0x60000.
=> sf probe
SF: Detected mx25u12835f with page size 256 Bytes, erase size 4 KiB, total 16 MiB
=> load mmc 1:1 10000000 u-boot-rockchip-spi.bin
1384448 bytes read in 119 ms (11.1 MiB/s)
=> sf update $fileaddr 0 $filesize
device 0 offset 0x0, size 0x152000
1179648 bytes written, 204800 bytes skipped in 9.901s, speed 143185 B/s
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable pinctrl for sdmmc and sdhci in SPL to support loading of FIT
image from SD and eMMC storage when booting from SPI NOR flash.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3568-rock-3a with new defaults.
Remove the SPL_ROCKCHIP_BACK_TO_BROM=y option, SPL is expected to load
next stage from a FIT image and then jump to next stage not back to
BootRom.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM.
Extend SPL_MAX_SIZE to 0x40000, SPL is loaded to 0x0 and TF-A is loaded
to 0x40000, use the space in between as SPL_MAX_SIZE.
Add config option to include useful gpio cmd.
Remove the CONFIG_NET_RANDOM_ETHADDR=y option, ethaddr and eth1addr is
set based on cpuid read from OTP.
Filter out assigned-clock props with CONFIG_OF_SPL_REMOVE_PROPS,
U-Boot proper will read and configure assigned-clock props.
Remove the CONFIG_SPL_PMIC_RK8XX=y option, the pmic is not used in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3568-evb with new defaults.
Remove the SPL_ROCKCHIP_BACK_TO_BROM=y option, SPL is expected to load
next stage from a FIT image and then jump to next stage not back to
BootRom.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM.
Extend SPL_MAX_SIZE to 0x40000, SPL is loaded to 0x0 and TF-A is loaded
to 0x40000, use the space in between as SPL_MAX_SIZE.
Add config options to include useful gpio, i2c, pmic and regulator cmd.
Remove the CONFIG_NET_RANDOM_ETHADDR=y option, ethaddr and eth1addr is
set based on cpuid read from OTP.
Filter out assigned-clock props with CONFIG_OF_SPL_REMOVE_PROPS,
U-Boot proper will read and configure assigned-clock props.
Add config options to enable support for the RK809 PMIC.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable pinctrl for sdmmc and sdhci in SPL to support loading of FIT
image from SD and eMMC storage when booting from SPI NOR flash.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3566-radxa-cm3-io with new defaults. Also add
missing supported mmc modes to sdhci node.
Remove the SPL_ROCKCHIP_BACK_TO_BROM=y option, SPL is expected to load
next stage from a FIT image and then jump to next stage not back to
BootRom.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM.
Extend SPL_MAX_SIZE to 0x40000, SPL is loaded to 0x0 and TF-A is loaded
to 0x40000, use the space in between as SPL_MAX_SIZE.
Add config option to include useful gpio cmd.
Remove the CONFIG_NET_RANDOM_ETHADDR=y option, ethaddr and eth1addr is
set based on cpuid read from OTP.
Filter out assigned-clock props with CONFIG_OF_SPL_REMOVE_PROPS,
U-Boot proper will read and configure assigned-clock props.
Add CONFIG_SYS_NS16550_MEM32=y to use 32bit access of serial register.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add drivers for PCIe , phy, and command.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable CONFIG_ROCKCHIP_SPI_IMAGE to build u-boot-rockchip-spi.bin.
Define CONFIG_SYS_SPI_U_BOOT_OFFS to write u-boot.itb at the expected
offset. Enable CONFIG_LTO to reduce size of SPL so that the mkimage
output fit before the 0x60000 offset in u-boot-rockchip-spi.bin.
=> sf probe
SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
=> load mmc 1:1 10000000 u-boot-rockchip-spi.bin
1442304 bytes read in 27 ms (50.9 MiB/s)
=> sf update $fileaddr 0 $filesize
device 0 offset 0x0, size 0x160200
1421824 bytes written, 20480 bytes skipped in 9.501s, speed 155432 B/s
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the use of SDMA mode to boost eMMC performance on ROCK Pi 4.
Also add missing flags to indicate the supported MMC modes.
Using mmc read command to read 32 MiB data shows following improvement:
=> time mmc read 10000000 2000 10000
Before: time: 3.178 seconds
After: time: 0.402 seconds
This also enables CONFIG_SPL_FIT_SIGNATURE option to help discover
any possible future issue with loading TF-A into DRAM/SRAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the use of SDMA mode to boost eMMC performance on RockPro64.
Also add missing flags to indicate the supported MMC modes.
Using mmc read command to read 32 MiB data shows following improvement:
=> time mmc read 10000000 2000 10000
Before: time: 3.178 seconds
After: time: 0.402 seconds
This also enables CONFIG_SPL_FIT_SIGNATURE option to help discover
any possible future issue with loading TF-A into DRAM/SRAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Loading part of TF-A into SRAM from eMMC using DMA fails on RK3399
similar to other Rockchip SoCs. Checksum validation fails with:
## Checking hash(es) for Image atf-2 ... sha256 error!
Bad hash value for 'hash' hash node in 'atf-2' image node
spl_load_simple_fit: can't load image loadables index 1 (ret = -1)
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Add a device tree property, u-boot,spl-fifo-mode, to control when the
rockchip_sdhci driver should disable the use of DMA and fallback on PIO
mode. Same device tree property is used by the rockchip_dw_mmc driver.
In commit 2cc6cde647 ("mmc: rockchip_sdhci: Limit number of blocks
read in a single command") the DMA mode was disabled using a CONFIG
option on RK3588. Revert that and instead disable DMA using the device
tree property for all RK3588 boards, also apply similar workaround for
all RK3399 boards.
Fixes: 2cc6cde647 ("mmc: rockchip_sdhci: Limit number of blocks read in a single command")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Quentin Schulz <foss+uboot@0leil.net> # RK3399 Puma, RK3588 Tiger
Add pinctrl driver in SPL. Do not remove pinctrl properties for SPL dtb.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable USB command, USB drivers, PHY and regulators, for USB host
operations.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
When using a list of writeable variables, the initial values come from
the built-in default environment since commit 5ab8105836
("env: Complete generic support for writable list"). Remove unnecessary
misuse of the env is nowhere driver as default environment.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
When using a list of writeable variables, the initial values come from
the built-in default environment since commit 5ab8105836
("env: Complete generic support for writable list"). Remove unnecessary
misuse of the env is nowhere driver as default environment.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
When using a list of writeable variables, the initial values come from
the built-in default environment since commit 5ab8105836
("env: Complete generic support for writable list"). Remove unnecessary
misuse of the env is nowhere driver as default environment.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Some of the Kria SOM and ZynqMP boards are using Analog Devices ethernet
phy. So, enable CONFIG_PHY_ADIN for all ZynqMP platforms.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230420085645.21260-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for Schneider Electric RZ/N1D and RZ/N1S boards, which
are based on the Reneasas RZ/N1 SoC devices.
The intention is to support both boards using a single defconfig, and to
handle the differences at runtime.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Move the TPL up a little to make room for the refcode binary blob. Also
increase the pre-relocation memory to make space for recent additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This adds a lot of code so that it cannot be built with the binary
blobs. It is not used on this board. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is useful when looking for tables in memory. Enable it for coreboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable support for NVMe storage devices. Update the driver to enable the
bus master bit, since coreboot does not do that automatically.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Turn these options on to make it easier to debug things.
Also enable dhrystone so we can get some measure of performance.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable this so that PCI devices can be used correctly without needing
to do a manual scan.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This is much more common on modern hardware, so default to using it.
This does not affect the normal UART, but does allow the debug UART to
work, since it uses serial_out_shift(), etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
- Rockchip NFC driver update and dev addr pointer api update;
- use standard dr_mode for usb driver;
- rock pi boards dts update;
- Add rk3566 Anbernic boards;
- Misc fixes for drivers;
rk3399-rock-pi-4a.dtb is enough for Radxa ROCK Pi 4A/B/A+/B+ and ROCK 4SE.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
