Adds to support JH7110 TRNG driver which is based on linux kernel's
jh7110-trng.c. This can support to generate 256-bit random numbers and
128-bit but this makes 256-bit default for convenience.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add STGCLK_SEC_HCLK and STGCLK_SEC_MISCAHB clocks for JH7110 TRNG
device.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The Zkr ISA extension (ratified Nov 2021) introduced the seed CSR. It
provides an interface to a physical entropy source.
A RNG driver based on the seed CSR is provided. It depends on
mseccfg.sseed being set in the SBI firmware.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
As noted in commit 3a6383207b ("mmc: sdhci: add the quirk for broken
r1b response"), some MMC controllers don't always set the transfer
complete bit with R1b responses.
According to the SD Host Controller Simplified Specification v4.20,
> In the case of a command pairing with response-with-busy[, Transfer
> Complete] is set when busy is de-asserted. Refer to DAT Line Active
> and Command Inhibit (DAT) in the Present State register.
By polling the DAT Line Active bit in the present state register, we can
detect when we are no longer busy, without waiting for a long timeout.
This results in much faster reads/writes on buggy controllers.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Tested-by: Henrik Grimler <henrik@grimler.se>
dm_pci_map_bar() return a value of (void *) already, hence no need
to cast it again before assigning to host->ioaddr.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
mmc_bind() in mmc-uclass.c calls blk_create_devicef() which is
defined in blk-uclass.c, so SPL_BLK is required by SPL_DM_MMC.
Implicitly select SPL_BLK for SPL_DM_MMC.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
PLL calibration needs to be enabled when operating in non fractional
mode. Add the sequence to do a fast calibration when using PLL
in this mode.
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Calculate the maximum length of the buffer when writing
across the page boundary. If the buffer length (len)
exceeds the page boundary (pagesize), split it. Use this
length instead of comparing the length with the pagesize,
because if the write start address (offset) is not at the
beginning of a page and the page_offset + len is greater
than the page boundary (pagesize), the write operation
would overflow the current page and the behaviour can be
undefined (e.g. at24).
Signed-off-by: Alex Michel <alex.michel@wiedemann-group.com>
Similar change was done by commit b4c2c151b1 ("Kconfig: Remove all
default n/no options") and again sync is required.
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com> # tegra
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Angelo Dureghello <angelo@kernel-space.org>
To avoid thermal burn out, program thermal shutdown
value in VTM (Voltage and Thermal Manager) IP.
Part of Linux kernel driver (drivers/thermal/k3_j72xx_bandgap.c)
is ported from kernel 6.6-rc1, which sets thermal shutdown values.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Neha Francis <n-francis@ti.com>
In current vexpress_config_probe code, it sets the uclass private data
directly. This will cause one compilation error:
drivers/misc/vexpress_config.c:114:27: error: lvalue required as left operand of assignment
114 | dev_get_uclass_priv(dev) = priv;
| ^
In this patch we set the uclass private data through struct member
.priv_auto, and this compilation error disappears.
Signed-off-by: Wei Chen <wei.chen@arm.com>
Signed-off-by: Qi Feng <qi.feng@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----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=gvDs
-----END PGP SIGNATURE-----
Merge tag 'tpm-next-27102023' of https://source.denx.de/u-boot/custodians/u-boot-tpm
bootX measurements and measurement API moved to u-boot core:
Up to now, U-Boot could perform measurements and EventLog creation as
described by the TCG spec when booting via EFI.
The EFI code was residing in lib/efi_loader/efi_tcg2.c and contained
both EFI specific code + the API needed to access the TPM, extend PCRs
and create an EventLog. The non-EFI part proved modular enough and
moving it around to the TPM subsystem was straightforward.
With that in place we can have a common API for measuring binaries
regardless of the boot command, EFI or boot(m|i|z), and contructing an
EventLog.
I've tested all of the EFI cases -- booting with an empty EventLog and
booting with a previous stage loader providing one and found no
regressions. Eddie tested the bootX part.
Eddie also fixed the sandbox TPM which couldn't be used for the EFI code
and it now supports all the required capabilities. This had a slight
sideeffect in our testing since the EFI subsystem initializes the TPM
early and 'tpm2 init' failed during some python tests. That code only
opens the device though, so we can replace it with 'tpm2 autostart'
which doesn't error out and still allows you to perfom the rest of the
tests but doesn't report an error if the device is already opened.
There's a few minor issues with this PR as well but since testing and
verifying the changes takes a considerable amount of time, I prefer
merging it now.
Heinrich has already sent a PR for -master containing "efi_loader: fix
EFI_ENTRY point on get_active_pcr_banks" and I am not sure if that will
cause any conflicts, but in any case they should be trivial to resolve.
Both the EFI and non-EFI code have a Kconfig for measuring the loaded
Device Tree. The reason this is optional is that we can't reason
when/if devices add random info like kaslr-seed, mac addresses etc in
the DT. In that case measurements are random, board specific and
eventually useless. The reason it was difficult to fix it prior to this
patchset is because the EFI subsystem and thus measurements was brought
up late and DT fixups might have already been applied. With this
patchset we can measure the DT really early in the future.
Heinrich also pointed out that the two Kconfigs for the DTB measurements
can be squashed in a single one and that the documentation only explains
the non-EFI case. I agree on both but as I said this is a sane working
version, so let's pull this first it's aleady big enough and painful to
test.
Add A1 SPIFC driver from Linux. Slightly modified to use u-boot driver
framework and accommodate to lack of ioread32_rep/iowrite32_rep.
Based on Linux version 6.6-rc4
Signed-off-by: Igor Prusov <IVPrusov@sberdevices.ru>
Signed-off-by: Martin Kurbanov <mmkurbanov@sberdevices.ru>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20231024225140.366571-2-ivprusov@sberdevices.ru
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
[trini: Drop <common.h> as it's not needed]
The driver needs to support getting the PCRs in the capabilities
command. Fix various other things and support the max number
of PCRs for TPM2.
Remove the !SANDBOX dependency for EFI TCG2 as well.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The R-Car Gen3 SD_CLK_CTRL register does not use BIT(16) to implement
divider 1/1024, instead BIT(16) is reserved bit and divider 1/1024 is
not supported. The divider 1/1024 is specific to Socionext variant of
the IP, as is indicated by Linux commit:
0196c8db8363 ("mmc: tmio: move tmio_mmc_set_clock() to platform hook")
"
Socionext (and Panasonic) uses bit 10 (CLKSEL) for 1/1. Also, newer
versions of UniPhier SoC variants use bit 16 for 1/1024.
"
Do not set the TMIO_SD_CAP_DIV1024 on Renesas R-Car platforms even if
the IP VERSION register does exist, and indicates IP version is newer
or equal to version 1.0 . The IP version 1.0 or newer does not imply
presence of the 1/1024 divider.
Since the TMIO driver is used exactly by two supported platforms, that
is Renesas R-Car and Socionext UniPhier, it is OK to check whether the
TMIO_SD_CAP_RCAR capability is not set to identify the UniPhier platform
and add the capability only on that platform.
Fixes: 58c35b17aa ("mmc: matsushita-common: Always check controller version")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Thuan Nguyen Hong <thuan.nguyen-hong@banvien.com.vn>
Unconditionally check for errors even after successful reception
of IRQ flag, since the hardware may set both an IRQ completion
flag and an error flag at the same time.
This mode of failure happens in case of an error during transfer,
in which case the hardware may set the expected IRQ completion
flag as well as error flags. The later is currently not checked
by the driver and such an error is not detected. Improve the
error detection.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Thuan Nguyen Hong <thuan.nguyen-hong@banvien.com.vn>
This driver is long superseded by renesas-sdhi.c and unused.
Drop the driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Paul Barker <paul.barker.ct@bp.renesas.com>
We should ensure that reset_free() is called in the error path.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Fixes: 93c811b733 ("mmc: renesas-sdhi: Initialize module on RZ/G2L")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
When debugging, one sometimes only gets partial output lines or
nothing at all from the last printf, because the uart has a largish
buffer, and the code after the printf() may cause the CPU to hang
before the uart IP has time to actually emit all the characters. That
can be very confusing, because one doesn't then know exactly where the
hang happens.
Introduce a config knob allowing one to wait for the uart fifo to
drain whenever a newline character is printed, roughly corresponding
to the effect of setvbuf(..., _IOLBF, ...) in ordinary C programs.
Since this uses IS_ENABLED() instead of cpp ifdef, we can remove the
ifdef around the _serial_flush() definition - if neither
CONSOLE_FLUSH_SUPPORT or CONSOLE_FLUSH_ON_NEWLINE are enabled, the
compiler elides _serial_flush(), but it won't warn about it being
unused.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
SCMI power domain management protocol is supported on sandbox
for test purpose. Add fake agent interfaces and associated
power domain devices.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
In this patch, added are helper functions to directly manipulate
SCMI power domain management protocol. DM compliant power domain
driver will be implemented on top of those interfaces in a succeeding
patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
- Add Board: rk3588 NanoPC-T6, Orange Pi 5, Orange Pi 5 Plus;
- clk driver fix for rk3568 and rk3588;
- rkmtd cmd support for rockchip nand device;
- dts update and sync from linux;
Currently bounce buffer support is enabled for all block devices
when available. Add a flag to blk_desc to enable only on demand.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add rkmtd class and drivers to create a virtual block device
to transfer Rockchip boot block data to and from NAND with
block orientated tools like "ums" and "rockusb".
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Prepare a rkmtd UCLASS in use for writing Rockchip boot blocks
in combination with existing userspace tools and rockusb command.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On Rockchip SoCs the first boot stages are written on NAND
with help of manufacturer software that uses a different format
then the MTD framework. Skip the automatic BBT scan with the
NAND_SKIP_BBTSCAN option to be able to pass the driver probe
function and to let the original data unchanged.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for XMC XM25QU128C (128M-bit) Serial Flash memory. Used on
the Xunlong Orange Pi 3B, 5 and 5 Plus boards.
Datasheet:
https://www.xmcwh.com/uploads/806/XM25QU128C_Ver2.0.pdf
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
[jonas@kwiboo.se: update commit message]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
It's normal to have no SATA drive attached to the controller, so return a
successful status when there is no block device found after probing.
Note: this patch depends on the previous patch
https://patchwork.ozlabs.org/project/uboot/patch/20230917230649.30357-1-mibodhi@gmail.com/
Resend the right patch.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add ahci sata bootdev and corresponding hunting function.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This is mostly about support for the Allwinner R528/T113s SoC, which is
reportedly the same die as the Allwinner D1, but with the two
Arm Cortex-A7 cores activated instead of the RISC-V one.
Using sunxi code outside of arch/arm proved to be difficult, so apart
from enabling this Arm SoC, the patches also prepare for more refactoring
to get the D1 nicely supported some day:
- We get rid of some Kconfig (hard-)coded GPIO pins, responsible for
enabling regulators.
- The GPIO code is moved out of arch/arm, into drivers/gpio.
- Some definitions are moved out of header files under asm/arch.
- Some T113s/D1 specific definitions are guarded by a generic Kconfig
symbol (CONFIG_SUNXI_GEN_NCAT2).
- The DRAM controller initialisation code is located under drivers/ram.
- The base SoC .dtsi files are shared (under arch/riscv, as in Linux).
Of course there are also the usual new SoC specific patches, like clock
and pinmux descriptions, alongside a rework of the pinctrl code, since
Allwinner changed the GPIO register layout, for the first time since
sunxi's inception.
On top of this the PSCI code sees some update, to provide SMP services
for R528/T113s boards. Many thanks to Sam for providing this code and
staying strong through the review cycles.
The final patch enables support for one popular board, I hope to see
more DTs and defconfigs contributed in the future!
Many thanks to all the various contributors, testers and reviewers,
that series was a real team effort!
fixed/gpio regulator counter in balance
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCZTY2dA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXDi0AJ0aJC4GlmmHtbmzBJdarGrb72zBtgCdGbzQaNj6
88xzVixBqtJPbJXGxKg=
=yCjQ
-----END PGP SIGNATURE-----
Merge tag 'video-20231022' of https://source.denx.de/u-boot/custodians/u-boot-video
- updates for pwm_backlight, simple_panel and tegra20 to keep
fixed/gpio regulator counter in balance
rk3588 frac pll:
FFVCO = ((m + k / 65536) * FFIN) / p
FFOUT = ((m + k / 65536) * FFIN) / (p * 2s)
k is the original code, but the K[15:0] is complement code
(6'b1000_0000_0000_0000 <= K[15:0] <= 16'b0111_1111_1111_1111),
need to be converted.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
aclk_top_root choose a parent clock that does not change.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
For a specific frequency.
Signed-off-by: Guochun Huang <hero.huang@rock-chips.com>
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This adds the remaining code bits to teach U-Boot about Allwinner's
newest SoC generation. This was introduced with the RISC-V based
Allwinner D1 SoC, which actually shares a die with the ARM cores versions
called R528 (BGA, without DRAM) and T113s (QFP, with embedded DRAM).
This adds the new Kconfig stanza, using the two newly introduced symbols
for the new SoC generation and pincontroller. It also adds the new symbols
to the relavent code places, to set all the hardcoded bits directly.
We need one DT override:
The ARM core version of the DT specifies the CPUX watchdog as
"reserved", which means it won't be recognised by U-Boot. Override this
in our generic sunxi-u-boot.dtsi, to let U-Boot pick up this watchdog,
so that the generic reset driver will work.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The Allwinner R528/T113-s/D1/D1s SoCs all share the same die, so use the
same DRAM initialisation code.
Make use of prior art here and lift some code from awboot[1], which
carried init code based on earlier decompilation efforts, but with a
GPL2 license tag.
This code has been heavily reworked and cleaned up, to match previous
DRAM routines for other SoCs, and also to be closer to U-Boot's coding
style and support routines.
The actual DRAM chip timing parameters are included in the main file,
since they cover all DRAM types, and are protected by a new Kconfig
CONFIG_SUNXI_DRAM_TYPE symbol, which allows the compiler to pick only
the relevant settings, at build time.
The relevant DRAM chips/board specific configuration parameters are
delivered via Kconfig, so this code here should work for all supported
SoCs and DRAM chips combinations.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Sam Edwards <CFSworks@gmail.com>
At the moment all Allwinner DRAM initialisation routines are stored in
arch/arm/mach-sunxi, even though those "drivers" are just a giant
collection of writel's, without any architectural dependency.
The R528/T113-s SoC (with ARM cores) and the D1/D1s Soc (with RISC-V
cores) share the same die, so should share the same DRAM init routines as
well.
To prepare for this, add a new sunxi directory inside drivers/ram, and
add some stub entries to prepare for the addition of the share DRAM code
for those SoCs.
The RISC-V D1(s) SoCs will probably use SPL_DM, so for that SoC this
would be the right directory anyway.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Since the D1 CCU binding is defined, we can add support for its
gates/resets, following the pattern of the existing drivers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Apart from using the new pinctrl MMIO register layout, the Allwinner D1
and related SoCs still need to usual set of mux values hardcoded in
U-Boot's pinctrl driver.
Add the values we need so far to this list, so that DM based drivers
will just work without further ado.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Allwinner seems to typically stick to a common MMIO memory map for
several SoCs, but from time to time does some breaking changes, which
also introduce new generations of some peripherals. The last time this
happened with the H6, which apart from re-organising the base addresses
also changed the clock controller significantly. We added a
CONFIG_SUN50I_GEN_H6 symbol back then to mark SoCs sharing those traits.
Now the Allwinner D1 changes the memory map again, and also extends the
pincontroller, among other peripherals.
To mark this generation of SoCs, add a CONFIG_SUNXI_GEN_NCAT2 symbol,
this name is reportedly used in the Allwinner BSP code, and prevents us
from inventing our own name.
Add this new symbol to some guards that were already checking for the H6
generation, since many features are shared between the two (like the
renovated clock controller).
This paves the way to introduce a first user of this generation.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Samuel Holland <samuel@sholland.org>
For the first time since at least the Allwinner A10 SoCs, the D1 (and
related cores) use a new pincontroller MMIO register layout, so we
cannot use our hardcoded, fixed offsets anymore.
Ideally this would all be handled by devicetree and DM drivers, but for
the DT-less SPL we still need the legacy interfaces.
Add a new Kconfig symbol to differenciate between the two generations of
pincontrollers, and just use that to just switch some basic symbols.
The rest is already abstracted enough, so works out of the box.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sam Edwards <CFSworks@gmail.com>
Tested-by: Sam Edwards <CFSworks@gmail.com>
Tested-by: Samuel Holland <samuel@sholland.org>
