Commit graph

197 commits

Author SHA1 Message Date
Lukasz Majewski
b6a0427554 Revert "mmc: fsl_esdhc: fix sd/mmc ddr mode clock setting issue"
This reverts commit 72a89e0da5, which
causes the imx53 HSC to hang as the eMMC is not working properly anymore.

The exact error message:
MMC write: dev # 0, block # 2, count 927 ... mmc write failed
0 blocks written: ERROR

imx53 is not using the DDR mode.

Debugging of pre_div and div generation showed that those values are
generated in a way, which is not matching the ones from working setup.

As the original patch was performing code refactoring, let's revert this
change, so all imx53 boards would work again.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-05-20 11:34:27 +08:00
Ye Li
da8e1f3cd4 mmc: fsl_esdhc: Fix wp_enable issue
The wp-gpios property is used for gpio, if this is set, the WP pin is muxed
to gpio function, can't be used as internal WP checking. However the codes
remain to use internal WP checking.

This patch changes to examine the "fsl,wp-controller" for enabling internal WP
checking, and "wp-gpios" for muxing to gpio.

Signed-off-by: Ye Li <ye.li@nxp.com>
2019-05-03 20:04:30 +08:00
Ye Li
72a89e0da5 mmc: fsl_esdhc: fix sd/mmc ddr mode clock setting issue
When sd/mmc work at DDR mode, like HS400/HS400ES/DDR52/DDR50 mode,
the output clock rate is half of the internal clock rate.

This patch set the DDR_EN bit first for DDR mode, hardware divide
the usdhc clock automatically, then follow the original sdr clock
setting method.

Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
2019-05-03 20:03:41 +08:00
Abel Vesa
d76706c89a mmc: fsl_esdhc: Fix DM_REGULATOR ifdefs for SPL builds
Since the fsl_esdhc will also be used by SPL, make the
preprocessor switches more generic to allow any kind of build.

Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-02-15 22:01:15 +01:00
Tom Rini
748ad078ee For 2019.04
-----BEGIN PGP SIGNATURE-----
 
 iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAlxQnKQPHHNiYWJpY0Bk
 ZW54LmRlAAoJECjE2NMq1et3Mm8L/0P99AB62Pu0NbAaVI9PnqaeR9/kUIvHlaPT
 RMuUIz931/1GDnugGsEEquSMUt69lfBCKYbF4sKiWObytHfYKvB/u638gqG2IoEt
 KcnWU5dagaTOyoyPOtr8EyKxThJtG2j1uN+fA5BCZ6A6CLnEW0biJXYLwN5P/DIE
 bsn9R+XfOV/ppaFh3p65SZfzzwKh6eUQLHqEphBbbAHCPz74QSeZMHkumbKplGOk
 1cjuFi8bekFnPGDDPW8jRvUNlhRD0kTjXoBj1eF2Q1g8lUj6La8yOsq1DAeGJjd1
 ywUDi8GPNYQ7HuHNzfZETWAYspNflARnPQwMemmNSKmmu6CO8aB6lt3JZWEUrnjL
 1D8LzMrRpyq1jEA0a57qsvTc8i3KA7X3FHTszP0flhiLKgBgE+5t1w8dc0wxC7HZ
 eF9TE3tGAmVzRVZwBh8HIDuKhe+y3uGKtvxl80DF8vQQWrXHq0GSC+pmdEXk7DGU
 OGYvdvVoThglZwM4vqeKlT/+1KLPCQ==
 =dOOt
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20190129' of git://git.denx.de/u-boot-imx

For 2019.04
2019-01-30 07:22:12 -05:00
Patrick Bruenn
791c88da31 mmc: fsl_esdhc: add compatible for fsl, imx53-esdhc
Add compatible "fsl,imx53-esdhc" to keep mmc working on i.MX53 platforms
with CONFIG_DM_MMC=y

Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
2019-01-28 20:55:46 +01:00
Angelo Dureghello
1f15cb8f5b drivers: esdhc: add support for ColdFire mcf5441x family
This patch has been tested on the mcf54415-based stmark2
board. The eSDHC driver works reliably using DMA mode.

Signed-off-by: Angelo Dureghello <angelo@sysam.it>
2019-01-26 08:13:56 -05:00
Yinbo Zhu
7a0425dd96 mmc: fsl_esdhc: make get_cd work well in dm_mmc_ops
This patch is to make get_cd work well when DM_MMC enabled

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2019-01-17 13:17:10 -08:00
Fabio Estevam
29c2edb42b mmc: fsl_esdhc: Avoid infinite loop in esdhc_send_cmd_common()
The following hang is observed on a Hummingboard 2 MicroSOM
i2eX iMX6D - rev 1.3 with no eMMC populated on board:

U-Boot SPL 2018.11+gf6206f8587 (Nov 16 2018 - 00:56:34 +0000)
Trying to boot from MMC1

U-Boot 2018.11+gf6206f8587 (Nov 16 2018 - 00:56:34 +0000)

CPU:   Freescale i.MX6D rev1.5 996 MHz (running at 792 MHz)
CPU:   Extended Commercial temperature grade (-20C to 105C) at 33C
Reset cause: POR
Board: MX6 HummingBoard2
DRAM:  1 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment

No panel detected: default to HDMI
Display: HDMI (1024x768)
In:    serial
Out:   serial
Err:   serial
---> hangs

which is caused by the following infinite loop inside esdhc_send_cmd_common()

	while (!(esdhc_read32(&regs->irqstat) & flags))
		;

Instead of looping forever, provide an exit path so that a timeout
error can be propagated in the case irqstat does not report
any interrupts, which may happen when no eMMC is populated on
board.

Reported-by: Ricardo Salveti <rsalveti@rsalveti.net>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Ricardo Salveti <rsalveti@rsalveti.net>
2019-01-14 11:26:12 -05:00
Peng Fan
cd357ad112 imx: rename mx8m,MX8M to imx8m,IMX8M
Rename mx8m,MX8M to imx8m,IMX8M

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jon Nettleton <jon@solid-run.com>
2019-01-01 14:12:18 +01:00
Peng Fan
3cb1450380 mmc: fsl_esdhc: add uclass clk support
When CONIFG_CLK is enabled, use uclass clk api to handle
the clock.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
2018-10-22 13:00:09 +02:00
Ye Li
d423c93b66 fsl_esdhc: Update usdhc driver to support i.MX8
Add CONFIG_ARCH_IMX8 to use the 64bits support in usdhc driver.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
2018-10-22 13:00:09 +02:00
Peng Fan
c76382ff7f mmc: fsl_esdhc: enable HS400 feature
The strobe dll code is ported from Linux Kernel:
drivers/mmc/host/sdhci-esdhc-imx.c
The comments are from the above file,
"For HS400 eMMC, there is a data_strobe line. This signal is generated
by the device and used for data output and CRC status response output
in HS400 mode. The frequency of this signal follows the frequency of
CLK generated by host. The host receives the data which is aligned to the
edge of data_strobe line. Due to the time delay between CLK line and
data_strobe line, if the delay time is larger than one clock cycle,
then CLK and data_strobe line will be misaligned, read error shows up.
So when the CLK is higher than 100MHz, each clock cycle is short enough,
host should configure the delay target. "

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
2018-09-10 20:48:19 -04:00
Jaehoon Chung
6511718254 mmc: add the MMC_CLK_ENABLE/DISABLE macro in mmc.h
mmc_set_clock() function has the disable argument as bool type.
When mmc_set_clock is called, it might be passed to "true" or "false".
But it's too confusion whether clock is enabled or disabled with only
"true" and "false".
To prevent the confusion, replace to MMC_CLK_ENABLE/DISABLE macro from
true/false.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2018-05-08 13:12:33 +09:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Peng Fan
51313b49f2 mmc: fsl_esdhc: support SDR104 and HS200
Introduce SDR104 and HS200 support
The implementation takes linux kernel sdhci.c and sdhci-esdhc-imx.c
as reference.
 - Implement esdhc_change_pinstate to dynamically change pad settings
 - Implement esdhc_set_timing
 - Implement esdhc_set_voltage to switch voltage
 - Implement fsl_esdhc_execute_tuning to execute time process
 - Enlarge the cfg->f_max to 200MHz.
 - Parse fsl,tuning-step, fsl,tuning-start-tap and
   fsl,strobe-dll-delay-target from device tree.
 - Parse no-1-8-v property
 - Introduce esdhc_soc_data to indicate the flags and caps

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2018-02-04 12:00:58 +01:00
Peng Fan
59d3782cda mmc: fsl_esdhc: add strobe and tuning entry
Add entries that will be used for tuning control.
The whole layout not changed, just expand reserved3[84] and
rename other reservedx in sequence.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2018-02-04 12:00:58 +01:00
Peng Fan
eec2d43795 mmc: fsl_esdhc: support i.MX8M
Support i.MX8M in fsl esdhc driver.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-02-04 12:00:58 +01:00
Benoît Thébaudeau
b9b4f146c9 mmc: fsl_esdhc: Fix i.MX53 eSDHCv3 clock
Commit 4f425280fa ("mmc: fsl_esdhc: Allow all supported prescaler
values") made it possible to set SYSCTL.SDCLKFS to 0 in SDR mode on
i.MX, thus bypassing the SD clock frequency prescaler, in order to be
able to get higher SD clock frequencies in some contexts. However, that
commit missed the fact that this value is illegal on the eSDHCv3
instance of the i.MX53. This seems to be the only exception on i.MX,
this value being legal even for the eSDHCv2 instances of the i.MX53.

Fix this issue by changing the minimum prescaler value for the single
instance of the i.MX53 eSDHCv3 controller.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-22 14:17:13 +09:00
Peng Fan
db359efd59 mmc: fsl_esdhc: Fix eMMC 1.8v setting issue
Current USDHC driver will reset VSELECT to 0 (3.3v) during mmc init,
then set to 1 for 1.8v eMMC I/O. When booting from eMMC, since ROM has
already set VSELECT to 1.8v before running the u-boot. This reset in
USDHC driver causes a short 2.2v pulse on CMD pin.

Fix this issue by not reset VSELECT to 0 when 1.8v flag is set.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2018-01-13 00:08:44 +09:00
Kishon Vijay Abraham I
35f6782055 mmc: add a new mmc parameter to disable mmc clock
mmc clock has to be disabled in certain cases like during
the voltage switch sequence. Modify mmc_set_clock function
to take disable as an argument that signifies if the
clock has to be enabled or disabled.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12 18:11:04 +09:00
Benoît Thébaudeau
bcfb365375 mmc: fsl_esdhc: Fix PIO timeout
The following error has been observed on i.MX25 with a high-speed SDSC
card:
    Data Write Failed in PIO Mode.

It was caused by the timeout set on PRSSTAT.BWEN, which was triggered
because this bit takes 15 ms to be set after writing the first block to
DATPORT with this card. Without this timeout, all the blocks are
properly written.

This timeout was implemented by decrementing a variable, so it was
depending on the CPU frequency. Fix this issue by setting this timeout
to a long enough absolute duration (500 ms).

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-11-07 10:26:27 +01:00
Simon Glass
e7881d85a9 dm: mmc: Drop CONFIG_DM_MMC_OPS
All boards which use DM_MMC have now been converted to use DM_MMC_OPS.
Drop the option and good riddance.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17 16:59:55 +09:00
Simon Glass
5248930ebf dm: imx: cm_fx6: Enable more driver model support
Enable driver model for MMC (including BLK), SATA and USB. Note that USB
does not yet work correctly since the nodes are disabled. Hopefully this
can be resolved by the maintainer.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17 16:44:17 +09:00
Simon Glass
653282b567 dm: mmc: fsl_esdhc: Update to support MMC operations
This driver does not currently support CONFIG_DM_MMC_OPS. Update it to
fully convert it to driver model.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17 16:44:17 +09:00
Simon Glass
4aac33f510 dm: mmc: fsl_esdhc: Update to support livetree
Update this driver to support a live device tree.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17 16:44:17 +09:00
Simon Glass
d6eb25e987 dm: mmc: fsl_esdhc: Drop mmc_init() call from fsl_esdhc_init()
We want to use fsl_esdhc_init() with driver model. Move the mmc_init() out
of this function so that we can use it for our common init.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17 16:44:17 +09:00
Simon Glass
e88e1d9c04 dm: mmc: fsl_esdhc: Set up platform data
With driver model we want to store the mmc and configuration structure in
platform data. Set up structure up and use it for non-DM as well.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17 16:44:17 +09:00
Simon Glass
201e828b22 dm: mmc: fsl_esdhc: Detect init failure
Since esdhc_init_common() can fail it should return an error code. Update
this and also adjust the timeout mechanism to use get_timer(), which is a
more common approach.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17 16:44:17 +09:00
Simon Glass
446e077a21 dm: mmc: fsl_esdhc: Detect reset failure
Since esdhc_reset() can fail it should return an error code. Update this
and also adjust the timeout mechanism to use get_timer(), which is a more
common approach.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17 16:44:17 +09:00
Simon Glass
9586aa6ea3 dm: mmc: fsl_esdhc: Set up common versions of operations
Driver model wants to use the core functions in this file but accesses the
driver-private data in a different way. Move the code into new 'common'
functions and set up stubs to call these. Also sort the operations into
alphabetical order for consistency.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17 16:44:17 +09:00
Simon Glass
09b465fd0f dm: mmc: fsl_esdhc: Pass private data to internal functions
With driver model we will not use mmc->priv to access driver-private data.
To accomodate this, update internal functions so that we can pass the
private data directly. This will allow the caller to obtain it as it
prefers.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17 16:44:17 +09:00
Yang Li
590e87d1a6 mmc: fsl_esdhc: not always setting esdhc fdt status to okay
We shouldn't always change the status to okay.  There could be
situations that the esdhc is intentionally disabled in the device
tree.

Signed-off-by: Li Yang <leoyang.li@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-08-09 09:57:32 -07:00
York Sun
9bb272e90a driver: mmc: fsl_esdhc: Fix compiling warning
Commit 4483b7eb added variable vqmmc_dev but only uses it under
CONFIG_DM_REGULATOR. Add the same macro to variable declaration to
get rid of compiling warning.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-08-09 09:11:29 -07:00
Peng Fan
f34ccce50a mmc: fsl_esdhc: drop CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT
CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT is not the correct method
to set I/O to 1.8. To boards that does not support vqmmc-supply,
use vs18_enable in fsl_esdhc_cfg. If regulator is supported,
use fixed 1.8V regulator for vqmmc-supply.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2017-07-12 09:44:22 +02:00
Peng Fan
4483b7eb88 dm: mmc: fsl_esdhc: handle vqmmc supply
Handle vqmmc supply. Some boards have a fixed I/O voltage
at 1.8V for emmc, so the usdhc also needs to be configured
as 1.8V by setting VSELECT bit. The vs18_enable is the one
that used to checking whether setting VSELECT or not in
the driver. So if vqmmc supply is 1.8V, set vs18_enable,
the driver will set VSELECT.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2017-07-12 09:44:22 +02:00
Peng Fan
32a9179f3a mmc: fsl_esdhc: introduce vs18_enable for 1.8V fix I/O
When using eMMC with 1.8V I/O, the VSELECT bit need to be set in
the USDHC controller when init.

This patch adds a parameter "vs18_enable" in fsl_esdhc_cfg
structure and priv data, so each controller can have different
settings.

We could not use CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT, it has problem
that it will apply to all USDHC controllers and it only set the 1.8V
at init phase. So if user does not select to the eMMC device,
the voltage on the I/O pins are not correct.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2017-07-12 09:44:22 +02:00
Tom Rini
821560fd8e Merge git://www.denx.de/git/u-boot-imx
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	include/configs/imx6qdl_icore_rqs.h
	include/configs/imx6ul_geam.h
	include/configs/imx6ul_isiot.h
2017-06-27 09:32:37 -04:00
Simon Glass
150c5afe5b dm: gpio: Add live tree support
Add support for requesting GPIOs with a live device tree.

This involves adjusting the function signature for the legacy function
gpio_request_by_name_nodev(), so fix up all callers.

Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes to stm32f746-disco.c:
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-01 07:03:10 -06:00
Simon Glass
a821c4af79 dm: Rename dev_addr..() functions
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.

In the end we will have:

   1. dev_read_addr...()    - works on devices, supports flat/live tree
   2. devfdt_get_addr...()  - current functions, flat tree only
   3. of_get_address() etc. - new functions, live tree only

All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.

Note this involves changing some dead code - the imx_lpi2c.c file.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-01 07:03:01 -06:00
Jagan Teki
2e87c440f6 mmc: fsl_esdhc: Move non DM_MMC code in #ifndef CONFIG_DM_MMC
Don't build non DM_MMC code when DM_MMC defined so move
them into #ifndef CONFIG_DM_MMC

Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-05-31 10:21:24 +02:00
Benoît Thébaudeau
4f425280fa mmc: fsl_esdhc: Allow all supported prescaler values
On i.MX, SYSCTL.SDCLKFS may be set to 0 in order to make the SD clock
frequency prescaler divide by 1 in SDR mode. In DDR mode, the prescaler
can divide by up to 512. Allow both of these settings.

The maximum SD clock frequency in High Speed mode is 50 MHz. On i.MX25,
this change makes it possible to get 48 MHz from the USB PLL
(240 MHz / 5 / 1) instead of only 40 MHz from the USB PLL
(240 MHz / 3 / 2) or 33.25 MHz from the AHB clock (133 MHz / 2 / 2).

Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-05-31 10:14:00 +02:00
Peng Fan
b60f14574e mmc: fsl_esdhc: support i.MX7ULP
Add compatible property for i.MX7ULP.
Add a weak init_usdhc_clk function, i.MX7ULP use this to init the clock.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
2017-03-17 09:27:08 +01:00
Simon Glass
e160f7d430 dm: core: Replace of_offset with accessor
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-02-08 06:12:14 -07:00
Tom Rini
0675f992db Merge git://git.denx.de/u-boot-fsl-qoriq 2017-01-19 12:22:23 -05:00
Yangbo Lu
fce1e16c55 mmc: fsl_esdhc: move 'status' property fixup into a weak function
Move fdt fixup of 'status' property into a weak function. This allows
board to define 'status' fdt fixup by themselves.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:46:30 -08:00
Yangbo Lu
a6473f8e3f mmc: fsl_esdhc: add 'fsl, esdhc' into of_match table
This patch is to add 'fsl,esdhc' into of_match table to support
driver model for QorIQ eSDHC.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:28:20 -08:00
Yangbo Lu
fc8048a88e mmc: fsl_esdhc: make GPIO support optional
There would be compiling error as below when enable driver model for esdhc.
undefined reference to `dm_gpio_get_value'
undefined reference to `gpio_request_by_name_nodev'
This patch is to make GPIO support optional with CONFIG_DM_GPIO. Because
all boards of QorIQ platform don't need it and they just check register for
CD/WP status, only some boards of i.MX platform require this.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:28:14 -08:00
Jaehoon Chung
07b0b9c00c mmc: change the set_ios return type from void to int
To maintain consistency, set_ios type of legacy mmc_ops changed to int.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2017-01-11 19:40:13 +09:00
Peng Fan
35ae99467d dm: mmc: intialize dev when probe
Need to initialize mmc->dev when probe, or will met
"dev_get_uclass_priv: null device", when `mmc dev 1`.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-04 15:41:01 +02:00
Jaehoon Chung
915ffa5213 mmc: use the generic error number
Use the generic error number instead of specific error number.
If use the generic error number, it can debug more easier.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
2016-08-05 11:21:25 +09:00
Jaehoon Chung
70f862808e mmc: fsl_esdhc: remove the duplicated header file
"mmc.h" is already included. It's duplicated.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-08-05 11:21:25 +09:00
Peng Fan
1483151e84 mmc: fsl: introduce wp_enable
Introudce wp_enable. To check WPSPL, wp_enable needs to be set
to 1 in board code.

Take i.MX6UL for example, for some boards, they do not use WP singal,
so they does not configure USDHC1_WP_SELECT_INPUT, and its default
value is 0(GPIO1_IO02). However GPIO1_IO02 is muxed for i2c usage and
SION bit set. So USDHC controller can always get wp signal and WPSPL
shows write protect and blocks driver continuing. This is not what
we want to see, so add wp_enable, and if set to 0, just omit the
WPSPL checking and this does not effect normal working of usdhc
controller.

If wp-gpios is provided in dts, wp_enable is set to 1, otherwise 0.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-28 12:08:53 -07:00
Ye Li
84ecdf6da9 fsl_esdhc: Update clock enable bits for USDHC
The USDHC moves the 4 clock bits CARD_CLK_SOFT_EN, IPG_PERCLK_SOFT_EN,
HCLK_SOFT_EN, and IPG_CLK_SOFT_EN from sysctl register to vendorspec
register. The driver uses RSTA to replace the clock gate off
operation. But this is not a good solution because:
1. when using RSTA, we should wait this bit to clear by itself. This is not
   implemeneted in the code.
2. After RSTA is set, it is recommended that the Host Driver reset the
   external card and reinitialize it.

So in this patch, we change to use the vendorspec registers for these bits
operation.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-28 12:08:53 -07:00
Peng Fan
f53225cce4 mmc: fsl: reset to normal boot mode when eMMC fast boot
When booting in eMMC fast boot, MMC host does not exit from
boot mode after bootrom loading image. So the first command
'CMD0' sent in uboot will pull down the CMD line to low and
cause errors.

This patch cleans the MMC boot register in "mmc_init" to put the
MMC host back to normal mode.

Also clear DLL_CTRL delay line settings at USDHC initialization
to eliminate the pre-settings from boot rom.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-28 12:08:53 -07:00
Eddy Petrișor
9702ec00e9 armv8: s32v234: Introduce basic support for s32v234evb
Add initial support for NXP's S32V234 SoC and S32V234EVB board.

The S32V230 family is designed to support computation-intensive applications
for image processing. The S32V234, as part of the S32V230 family, is a
high-performance automotive processor designed to support safe
computation-intensive applications in the area of vision and sensor fusion.

Code originally writen by:
Original-signed-off-by: Stoica Cosmin-Stefan <cosminstefan.stoica@freescale.com>
Original-signed-off-by: Mihaela Martinas <Mihaela.Martinas@freescale.com>
Original-signed-off-by: Eddy Petrișor <eddy.petrisor@gmail.com>

Signed-off-by: Eddy Petrișor <eddy.petrisor@nxp.com>
2016-06-13 08:56:35 -04:00
Yangbo Lu
cc634e2836 mmc: fsl_esdhc: fix check_and_invalidate_dcache_range function
In function check_and_invalidate_dcache_range(), there are incorrect
start address and end address of the dcache range calculated for
Layerscape platforms. This patch is to fix this issue.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-03 14:12:05 -07:00
Peng Fan
96f0407b00 fsl: esdhc: support driver model
Support Driver Model for fsl esdhc driver.

1. Introduce a new structure struct fsl_esdhc_priv
2. Refactor fsl_esdhc_initialize which is originally used by board code.
   - Introduce fsl_esdhc_init to be common usage for DM and non-DM
   - Introduce fsl_esdhc_cfg_to_priv to build the bridge for non-DM part.
   - The original API for board code is still there, but we use
     'fsl_esdhc_cfg_to_priv' and 'fsl_esdhc_init' to serve it.
3. All the functions are changed to use 'struct fsl_esdhc_priv', except
   fsl_esdhc_initialize.
4. Since clk driver is not implemented, use mxc_get_clock to geth
   the clk and fill 'priv->sdhc_clk'.

Has been tested on i.MX6UL 14X14 EVK board:
"
=>dm tree
....
 simple_bus  [ + ]    |   `-- aips-bus@02100000
  mmc        [ + ]    |       |-- usdhc@02190000
  mmc        [ + ]    |       |-- usdhc@02194000
....
=> mmc list
FSL_SDHC: 0 (SD)
FSL_SDHC: 1 (SD)
"

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Hector Palacios <hector.palacios@digi.com>
Cc: Eric Nelson <eric@nelint.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Simon Glass <sjg@chromium.org>
Tested-By: Eric Nelson <eric@nelint.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-04-06 08:33:37 -07:00
Yangbo Lu
25503443ee mmc: fsl_esdhc: set Abort command type for CMD12
According to SD spec, CMD12, CMD52 for writing I/O abort in CCCR need
to be set an Abort command type when they are sent. So, we remove all
chip-specific #ifdefs and make it available for all platforms.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:13:13 -08:00
Yangbo Lu
e978a31b63 mmc: fsl_esdhc: increase data transaction timeout to 500ms
The MMC spec says "It is strongly recommended for hosts to implement
more than 500ms timeout value even if the card indicates the 250ms
maximum busy length."  Even the previous value of 300ms is known to
be insufficient for some cards. So, increase the timeout to 500ms.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:13:12 -08:00
Eric Nelson
f0b5f23f32 ARM: imx: fsl_esdhc: fix usage of low 4 bits of sysctl register
The low four bits of the SYSCTL register are reserved on the USDHC
controller on i.MX6 and i.MX7 processors, but are used for clocking
operations on earlier models.

Guard against their usage by hiding the bit mask macros on those
processors.

These bits are used to prevent glitches when changing clocks on
i.MX35 et al. Use the RSTA bit instead for i.MX6 and i.MX7.

>From the i.MX6DQ RM:
	To prevent possible glitch on the card clock, clear the
	FRC_SDCLK_ON bit when changing clock divisor value(SDCLKFS
	or DVS in System Control Register) or setting RSTA bit.

Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Hector Palacios <hector.palacios@digi.com>
2016-01-03 15:21:21 +01:00
Yangbo Lu
bf50be835e mmc: fsl_esdhc: enable EVDD automatic control for SD/MMC Legacy Adapter Card
When detecting SDHC Adapter Card Type 2(SD/MMC Legacy Adapter Card),
enable EVDD automatic control via SDHC_VS. This could support SD card
IO voltage switching for UHS-1 speed mode.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-02 08:50:29 -08:00
Yangbo Lu
cdc69550d2 mmc: fsl_esdhc: enable dat[4:7] for eMMC4.5 Adapter Card
If adapter card type identification is supported for platform, we would
enable dat[4:7] for eMMC4.5 Adapter Card.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-02 08:49:51 -08:00
Shaohui Xie
512bdbd46a Powerpc: eSDHC: expand a fix to T4160
commit b8e5b07225 "Powerpc: eSDHC: Fix mmc read write err in uboot of
T4240QDS board", T4160 also needs this fix.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-02 08:49:32 -08:00
Yangbo Lu
8ef0d5c438 armv8/ls1043ardb: esdhc: Add esdhc support for ls1043ardb
This patch adds esdhc support for ls1043ardb.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29 10:34:01 -07:00
Tom Rini
e3d50d4292 fsl_esdhc.c: Always make check_and_invalidate_dcache_range available
This function is called from esdhc_send_cmd so we need it available to
everyone.

Signed-off-by: Tom Rini <trini@konsulko.com>
2015-08-02 10:27:52 -04:00
Peng Fan
4683b22065 mmc:fsl_esdhc invalidate dcache before read
DCIMVAC is upgraded to DCCIMVAC for the individual processor
(Cortex-A7) that the DCIMVAC is executed on.

We should follow the linux dma follow. Before DMA read, first
invalidate dcache then after DMA read, invalidate dcache again.

With the DMA direction DMA_FROM_DEVICE, the dcache need be
invalidated again after the DMA completion. The reason is
that we need explicity make sure the dcache been invalidated
thus to get the DMA'ed memory correctly from the physical memory.
Any cache-line fill during the DMA operations such as the
pre-fetching can cause the DMA coherency issue, thus CPU get the stale data.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Signed-off-by: Jason Liu <r64343@freescale.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2015-07-26 12:17:20 +02:00
Tom Rini
d81572c272 Merge git://git.denx.de/u-boot-mpc85xx 2015-05-05 14:57:23 -04:00
Yangbo Lu
253d5bdd64 mmc: fsl_esdhc: update eMMC44 adapter card erase timeout
Freescale eMMC44 adapter card uses Micron N2M400FDB311A3CF eMMC
memory. According to the silicon datasheet, secure erase timeout
is 600ms. So increase erase timeout value from 250ms to 600ms.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
2015-05-05 12:29:42 +03:00
Rob Herring
5a20397b00 mmc: remove the MMC_MODE_HC flag
High capacity support is not a host capability, but a device capability
that is queried via the OCR. The flag in the operating conditions
request argument can just be set unconditionally. This matches the Linux
implementation.

[panto] Hand merged and renumbering MMC_MODE_DDR_52MHz.

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
2015-05-05 12:29:36 +03:00
Yangbo Lu
2d9ca2c72c mmc: fsl_esdhc: Add peripheral clock support
The SD clock could be generated by platform clock or peripheral
clock for some platforms. This patch adds peripheral clock
support for T1024/T1040/T2080. To enable it, define
CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-05-04 09:25:39 -07:00
Yangbo Lu
5a8dbdc6b4 mmc: fsl_esdhc: Add adapter card type identification support
Add adapter card type identification support by reading
FPGA STAT_PRES1 register SDHC Card ID[0:2] bits. To use this function,
define CONFIG_FSL_ESDHC_ADAPTER_IDENT.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
[York Sun: resolve conflicts in README.fsl-esdhc]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-05-04 09:25:19 -07:00
Yangbo Lu
8b06460e55 ls2085a: esdhc: Add esdhc support for ls2085a
This patch adds esdhc support for ls2085a.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
2015-04-23 16:46:51 -07:00
Peng Fan
323aaaa1e3 mmc: fsl_esdhc fix register offset
Commit f022d36e8a introduces
error register offset.

Change the "char reserved3[59]" to "char reserved3[56]".

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-03-17 09:09:47 -04:00
Stefano Babic
b9cb64825b Merge branch 'master' of git://git.denx.de/u-boot 2015-03-02 09:42:53 +01:00
Volodymyr Riazantsev
0e1bf614d5 mmc: fsl_esdhc: Add support for DDR mode
Add support of the DDR mode for eSDHC driver.
Enable it for i.MX6 SoC family only.

Signed-off-by: Volodymyr Riazantsev <volodymyr.riazantsev@globallogic.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-02-24 13:11:10 -08:00
Otavio Salvador
ee0c538951 mmc: fsl_esdhc: Add support to force VSELECT set
Some boards cannot do voltage negotiation but need to set the VSELECT
bit forcely to ensure it to work at 1.8V.

This commit adds CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT flag for this use.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2015-02-23 09:11:42 +01:00
Otavio Salvador
f022d36e8a mmc: fsl_esdhc: Add CMD11 support to switch to 1.8V
This adds support to switch to 1.8V in case CMD11 succeeds.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Marek Vasut <marex@denx.de>
2015-02-23 09:11:42 +01:00
Tom Rini
21008ad638 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
Conflicts:
	drivers/mmc/fsl_esdhc.c

Signed-off-by: Tom Rini <trini@ti.com>
2014-11-26 11:22:29 -05:00
Tom Rini
dee332ffb7 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2014-11-24 12:02:12 -05:00
Masahiro Yamada
b41411954d linux/kernel.h: sync min, max, min3, max3 macros with Linux
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does.  This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.

Many of references of those macros must be fixed to suppress warnings.
We have two options:
 - Use min, max, min3, max3 only when the arguments have the same type
   (or add casts to the arguments)
 - Use min_t/max_t instead with the appropriate type for the first
   argument

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
2014-11-23 06:48:30 -05:00
Ye.Li
a3d6e38617 mmc: fsl_esdhc: Update esdhc driver for iMX6SX
The reset value of "uSDHCx_INT_STATUS_EN" register is changed to 0
on iMX6SX. So the fsl_esdhc driver must update to set the register,
otherwise no state can be detected.

Signed-off-by: Ye.Li <B37916@freescale.com>
2014-11-20 10:44:42 +01:00
Markus Niebel
3b4b9a3377 mmc: fsl_esdhc: fix f_max retrieval during init
for multi instance API we use struct fsl_esdhc_cfg to
pass the clock rate. Do not set f_max from global data,
since this is wrong for multi instance case.

Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-11-19 18:17:12 -08:00
Masahiro Yamada
c79cba37b3 cosmetic: replace MIN, MAX with min, max
The macro MIN, MAX is defined as the aliase of min, max,
respectively.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-09-24 18:30:29 -04:00
Wang Huan
19060bd886 ls102xa: esdhc: Add esdhc support for LS102xA
For LS1, esdhc is big-endian IP. Accessing the registers
should be in big-endian mode. So we use esdhc_read32()
to read Host controller capabilities register for LS1.

For LS1, when using CMD12, cmdtype need to be set to
ABORT, otherwise, next read command will hang.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
2014-09-08 10:30:34 -07:00
Tom Rini
10dc77716f esdhc/usdhc: Fix warning when CONFIG_SYS_FSL_ESDHC_USE_PIO is not set
In 7168977 we made calls to check_and_invalidate_dcache_range()
conditional on !CONFIG_SYS_FSL_ESDHC_USE_PIO.  Only define this function
in this case as well.

Signed-off-by: Tom Rini <trini@ti.com>
2014-05-23 09:19:05 -04:00
Ye.Li
716897760f esdhc/usdhc: Fix PIO mode bug in fsl_esdhc driver
When configure the fsl_esdhc driver to PIO mode by defining
"CONFIG_SYS_FSL_ESDHC_USE_PIO", the SD/MMC read and write will fail.

Two bugs in the driver to cause the issue:
1. The read buffer was invalidated after reading from DATAPORT register,
which should be only applied to DMA mode. The valid data in cache was
overwritten by physical memory.
2. The watermarks are not set in PIO mode, will cause according state not
be set.

Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
2014-05-22 18:52:45 +03:00
Chunhe Lan
0b2e13d9cc powerpc/85xx: Add T4240RDB board support
T4240RDB board Specification
----------------------------
Memory subsystem:
   6GB DDR3
   128MB NOR flash
   2GB NAND flash

Ethernet:
   Eight 1G SGMII ports
   Four 10Gbps SFP+ ports

PCIe:
   Two PCIe slots

USB:
   Two USB2.0 Type A ports

SDHC:
   One SD-card port

SATA:
   One SATA port

UART:
   Dual RJ45 ports

Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: fix CONFIG_SYS_QE_FMAN_FW_ADDR in T4240RDB.h]
2014-05-13 08:24:32 -07:00
Haijun.Zhang
1336e2d343 mmc:eSDHC: Workaround for data timeout issue on Txxx SoC
1. The Data timeout counter value in eSDHC_SYSCTL register is
not working as it should be, so add quirks to enable this
workaround to fix it to the max value 0xE.

2. Add CONFIG_SYS_FSL_ERRATUM_ESDHC111 to enable its workaround.

* Update of patch for change mmc interface by
	Pantelis Antoniou <panto@antoniou-consulting.com>

Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-04-02 13:25:01 +03:00
Andrew Gabbasov
8a573022c3 mmc: fsl_esdhc: add controller reset in case of data related errors too
The controller reset is performed now if command error occurs.
This commit adds the reset for the case of data related errors too.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-04-02 13:17:12 +03:00
Andrew Gabbasov
fb823981c5 mmc: fsl_esdhc: fix calculation of timeout for data transactions
Calculation of the timeout value should be based on actual clock value,
written to controller registers. Since mmc->tran_speed is either the
maximum allowed speed, or the preliminary value, that is be not yet
set to registers, the actual timeout, taken by the controller, based
on its clock settings, may be much longer than expected, based on
mmc->tran_speed value. In particular it happens at early initialization
stage, when typical value of mmc->tran_speed is 20MHz or 26MHz, while
actual clock setting, configured in the controller, is 400kHz.
It's more correct to use mmc->clock value for timeout calculation instead.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-04-02 13:16:56 +03:00
Pantelis Antoniou
93bfd61677 mmc: Split mmc struct, rework mmc initialization (v2)
The way that struct mmc was implemented was a bit of a mess;
configuration and internal state all jumbled up in a single structure.

On top of that the way initialization is done with mmc_register leads
to a lot of duplicated code in drivers.

Typically the initialization got something like this in every driver.

	struct mmc *mmc = malloc(sizeof(struct mmc));
	memset(mmc, 0, sizeof(struct mmc);
	/* fill in fields of mmc struct */
	/* store private data pointer */
	mmc_register(mmc);

By using the new mmc_create call one just passes an mmc config struct
and an optional private data pointer like this:

	struct mmc = mmc_create(&cfg, priv);

All in tree drivers have been updated to the new form, and expect
mmc_register to go away before long.

Changes since v1:

* Use calloc instead of manually calling memset.
* Mark mmc_register as deprecated.

Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-03-24 12:58:56 +02:00
Pantelis Antoniou
22cb7d334e mmc: Convert mmc struct's name array to a pointer
Using an array is pointless; even more pointless (and scary) is using
sprintf to fill it without a format string.

Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-03-24 11:32:10 +02:00
Pantelis Antoniou
ab769f227f mmc: Remove ops from struct mmc and put in mmc_ops
Remove the in-structure ops and put them in mmc_ops with
a constant pointer to it.

This makes the mmc structure smaller as well as conserving
code space (in theory).

All in-tree drivers are converted as well; this is done in a
single patch in order to not break git bisect.

Changes since V1:
Fix compilation b0rked issue on omap platforms where OMAP_GPIO was
not set.

Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-03-24 11:32:10 +02:00
Haijun.Zhang
d47e3d2707 esdhc: Detecting 8 bit width before mmc initialization
The upper 4 data signals of esdhc are shared with spi flash.
So detect if the upper 4 pins are assigned to esdhc before
enable sdhc 8 bit width.

Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-01-22 08:56:34 -08:00
Haijun.Zhang
f7e27cc5ee esdhc: Workaround for card can't be detected on T4240QDS
Card detection pin is ineffective on T4240QDS Rev1.0.
There are two cards can be connected to board.
1. eMMC card is built-in board, can not be removed. so
   For eMMC card it is always there.
2. Card detecting pin is functional for SDHC card in Rev2.0.

This workaround force sdhc driver scan and initialize the card
regardless of whether the card is inserted or not in case Rev1.0.

Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-01-22 08:56:15 -08:00
Haijun.Zhang
ef38f3ffb9 powerpc/esdhc: Add 3.3v voltage support in esdhc capacity register
T4240QDS eSDHC host capabilities reigster should have VS33 bit define.
Add quirk CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 to deal with capacity
missing

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2013-10-31 09:55:34 +02:00
Haijun.Zhang
a54d681132 esdhc: memset mmc struct before putting into use
struct mmc should be clear to all '0' after malloc to avoid
unexpect variable value.

Like mmc->has_init = xxx.
In this case mmcinfo will believe the card had been initialized before
and skip the initialization.

Test on P5040 and T4240,
Error Log:

=> mmcinfo
Device: FSL_SDHC
Manufacturer ID: 0
OEM: 0
Name: Tran Speed: 0
Rd Block Len: 0
MMC version 0.0
High Capacity: No
Capacity: 0 Bytes
Bus Width: 0-bit
=>

Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Signed-off-by: Xie Shaohui-B21989 <B21989@freescale.com>
Tested-by: Ryan Barnett <rjbarnet@rockwellcollins.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2013-10-31 09:55:34 +02:00
Haijun.Zhang
511948b2cb Powerpc/esdhc: Add simple description of esdhc register
Add some descriptions for esdhc register for easily using.

Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2013-10-31 09:55:34 +02:00
Haijun.Zhang
5f9b9f867d powerpc/esdhc: Map register for eSDHC Host Controller V3.0
eSDHC host controller has new register to support SD Spec 3.0.
And the according host controller version was Freescale eSDHC
Version 3.0.

Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2013-10-31 09:55:33 +02:00