Commit graph

40437 commits

Author SHA1 Message Date
Siva Durga Prasad Paladugu
e1992276c3 ARM64: zynqmp: Add support for SD1 with level shifters bootmode
Add support for SD1 with level shifters bootmode.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15 15:28:05 +01:00
Michal Simek
8ecd50c8c9 ARM64: zynqmp: Record board name as serial number for DFU/FASTBOOT
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15 15:28:05 +01:00
Soren Brinkmann
0cba6abbba ARM64: zynqmp: Adjust to new SMC interface to get silicon version
The new FW interface returns the IDCODE and version register, leaving
extracting bitfields to the caller.

Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15 15:28:05 +01:00
Michal Simek
05c59d0bc8 ARM: zynq: Add support for Zynq 7000S 7007s/7012s/7014s devices
Zynq 7000S (Single A9 core) devices is using different ID code.
This patch adds this new codes and assign them.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15 15:28:04 +01:00
Siva Durga Prasad Paladugu
4eaf8f5424 net: zynq_gem: Correct SGMII enable bit setting
Correct the SGMII enable bit position to 27 instead
of 31.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-11-15 15:28:01 +01:00
Siva Durga Prasad Paladugu
27183d7c22 net: zynq_gem: Modify the nwcfg bit definitions
Modify the nwcfg bit definitions to have 32-bit
by removing the extra nibble.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-11-15 15:28:00 +01:00
Siva Durga Prasad Paladugu
02bcff2c56 nand: arasan_nfc: Clear ecc on bit while sending read command
Clear ecc ON bit while sending read command as all types
of read command(like reading spare) doesnt need ECC to be
enabled. It has been anyway taken care in other places
whereever required using arasan_nand_enable_ecc().

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15 15:27:57 +01:00
Michal Simek
cde28c8155 zynq: nand: Runtime detection of nand buswidth through slcr
This patch adds support to check the buswidth on nand flash
at runtime based on nand MIO configurations done by FSBL.

User needs to correctly configure the MIO's based on the
buswidth supported by the nand flash which is present on the board.

Added nand8 and nand16 @periph names on slcr driver.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15 15:27:51 +01:00
Siva Durga Prasad Paladugu
ba8adb26a0 zynq: nand: Enable Nand flash controller driver a zynq board
Enable zynq Nand flash controller driver for a zynq ZC770
XM011(dc2) board.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15 15:27:50 +01:00
Siva Durga Prasad Paladugu
ae798d2e7d mtd: nand: zynq_nand: Add nand driver support for zynq
Add nand flash controller driver support for zynq SoC.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15 15:27:50 +01:00
Mike Looijmans
2d48caa47d ARM: zynq: Add support for the topic-miami system-on-modules and carrier boards
The topic-miami SoMs contain a Zynq xc7z015 or xc7z030 SoC, 1GB DDR3L RAM,
32MB QSPI NOR flash and 256MB NAND flash.

The topic-miamiplus SoMs contain a Zynq xc7z035, xc7z045 or xc7z100 SoC,
2x 1GB DDR3L RAM, 64MB dual-parallel QSPI flash, clock sources
and a fan controller.

The "Florida" carrier boards add SD, USB, ethernet and other interfaces.

Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15 15:27:50 +01:00
Mike Looijmans
ba4ccf9348 ARM: zynq: Make SYS_VENDOR configurable
Add a string description for SYS_VENDOR to allow configuring boards from
other vendors than just "xilinx".

Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15 15:27:50 +01:00
Michal Simek
56c7e80155 tools: mkimage: Check if file is regular file
Current Makefile.spl passes -R parameter which is not empty
and pointing to ./ folder.
"./tools/mkimage -T zynqmpimage -R ./"" -d spl/u-boot-spl.bin
spl/boot.bin"
That's why mkimage is trying to parse ./ file and generate
register init which is wrong.
Check that passed filename is regular file. If not do not work with it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15 15:27:45 +01:00
Mike Looijmans
3b6460809c tools: mkimage: Add support for initialization table for Zynq and ZynqMP
The Zynq/ZynqMP boot.bin file contains a region for register initialization
data. Filling in proper values in this table can reduce boot time
(e.g. about 50ms faster on QSPI boot) and also reduce the size of
the SPL binary.

The table is a simple text file with register+data on each line. Other
lines are simply skipped. The file can be passed to mkimage using the
"-R" parameter.

It is recommended to add reg init file to board folder.
For example:
CONFIG_BOOT_INIT_FILE="board/xilinx/zynqmp/xilinx_zynqmp_zcu102/reg.int

Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15 15:27:37 +01:00
Tom Rini
29e0cfb4f7 Prepare v2016.11
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-11-14 11:27:11 -05:00
Hans de Goede
8f7c672ce6 MAINTAINERS: mark sunxi status as Orphan
Ian has not had any time for sunxi for some time now and I'm
in the same situation now, so I'm stepping down as sunxi
custodian and marking the sunxi support as Orphan.

Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-11-14 11:24:44 -05:00
Stefan Roese
22bb1a7a1b video: bmp: Fix compilation errors with CONFIG_BMP_xxBPP enabled
Compiling the 'bmp' command with DM and having one of the following macros
enabled:

CONFIG_BMP_16BPP, CONFIG_BMP_24BPP ONFIG_BMP_32BPP

generates this error:

drivers/video/video_bmp.c: In function ‘video_bmp_display’:
drivers/video/video_bmp.c:315:22: error: ‘lcd_line_length’ undeclared (first use in this function)
    fb -= width * 2 + lcd_line_length;
                          ^

This patch moves to using the correct variable instead and enables the
'bmp' command for DM again.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
2016-11-13 15:54:38 -05:00
Marek Vasut
73d570a76d net: write enetaddr down to hardware on env_callback
If mac-address is changed using "setenv ethaddr ...." command the new
mac-adress also must be written into the responsible ethernet driver.
This fixes the legacy ethernet handling.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Hannes Schmelzer <oe5hpm@oevsv.at>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
2016-11-13 15:54:38 -05:00
Vignesh R
948b8bbd5f spi: ti_qspi: Fix baudrate divider calculation
Fix the divider calculation logic to choose a value so that the
resulting baudrate is either equal to or closest possible baudrate less
than the requested value. While at that, cleanup ti_spi_set_speed().

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-11-13 15:54:37 -05:00
Vignesh R
84295f2a20 ARM: dts: dra7xx: Update spi-max-frequency for qspi slave node
Update the spi-max-frequency property of m25p80 flash slave to match
that of TI QSPI controller node, so that QSPI operations happen at
maximum supported frequency of 76.8MHz.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-11-13 15:54:37 -05:00
Lokesh Vutla
4d0fec0e69 ARM: k2g: Update PLL Multiplier and divider values
Only a certain set of PLLM/D values are recommended to configure the DDR
at the required speeds for a given clock input frequency. Updating these
values as specified in Data Sheet[1] Table 5-18

[1] http://www.ti.com/lit/ds/symlink/66ak2g02.pdf

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-11-13 15:54:37 -05:00
Lokesh Vutla
8b01ebd812 ARM: keystone2: PLL: Enable glitch free initialization sequence
Update the PLL initialization sequence to avoid glitches while
programming. User guide for the same is available at[1].

[1] http://www.ti.com/lit/ug/sprugv2h/sprugv2h.pdf

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-11-13 15:54:36 -05:00
Keerthy
06d43c808d arm: Set TTB XN bit in case DCACHE_OFF for LPAE mode
While we setup the mmu initially we mark set_section_dcache with
DCACHE_OFF flag. In case of non-LPAE mode the DCACHE_OFF macro
is rightly defined with TTB_SECT_XN_MASK set so as to mark all the
4GB XN. In case of LPAE mode  XN(Execute-never) bit is not set with
DCACHE_OFF. Hence XN bit is not set by default for DCACHE_OFF which
keeps all the regions execute okay and this leads to random speculative
fetches in random memory regions which was eventually caught by kernel
omap-l3-noc driver.

Fix this to mark the regions as XN by default.

Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-11-13 15:54:36 -05:00
Keerthy
2b373cb83c arm: print the cache config option in hex instead of decimal
Printing the option value in hex makes it more comprehensible.

Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-11-13 15:54:36 -05:00
Diego Dorta
2ffec69b6f mx6ull_14x14_evk: Add README file
Add a README file to help users getting started with the board.

Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-11-13 15:54:35 -05:00
Fabien Parent
02c2de6eb0 davinci: omapl138_lcdk: keep booting even when MAC address is invalid
If the MAC address specified on the EEPROM is invalid (multicast or
zero address), then u-boot fails to boot. Having a bad MAC address
in the EEPROM should not prevent the system from booting.

This commit changes the error path to just print an error messages
in case of bad MAC address.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-11-13 15:54:35 -05:00
Alex G
c19a28bc65 board: am335x/mux: Do not hang when encountering a bad EEPROM
In most cases, the SPL and u-boot.img will be on the same boot media.
Since the SPL was loaded by the boot rom, the pinmux will already have
been configured for this media. This, the board will still be able to
boot successfully, or at least reach the u-boot console, where more
recovery options are available.

I've encountered this on a beaglebone black with a corrupted EEPROM.
Removing this check allowed the board to boot successfully. I've also
seen this on EVM-based boards with an unprogrammed EEPROM. On those
boards, for some reason there were no UART messages. This made it look
as if the SOC was dead.

Remove the hang(), as it is not a fatal error. Also reformat the error
message to be clearer as to the cause. The original message made it
appear as if the wrong binary was being loaded.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-11-13 15:54:35 -05:00
Ladislav Michl
4fa72bd3fc igep00x0: add Hynix timings
Tested on IGEPv2 with Micron MT29F4G16ABBDA3W and
Hynix H27S4G6F2DKA-BM

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Javier Martinez Canillas <javier@samsung.com>
Tested-by: Javier Martinez Canillas <javier@samsung.com>
2016-11-13 15:54:34 -05:00
Ladislav Michl
2baaa31024 igep00x0: consolidate defconfigs
Defconfigs should remain the same except CONFIG_SYS_EXTRA_OPTIONS.
Drop NAND specific defconfig as flash type is runtime detected.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Javier Martinez Canillas <javier@samsung.com>
2016-11-13 15:54:34 -05:00
Ladislav Michl
ad560f87e0 igep00x0: disable CONFIG_DISPLAY_BOARDINFO
As a single U-Boot binary can now run on various board modifications,
drop CONFIG_DISPLAY_BOARDINFO as it prints flash memory information
too early to give us chance to easily detect it. Also saves few bytes
as a bonus.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Javier Martinez Canillas <javier@samsung.com>
Tested-by: Javier Martinez Canillas <javier@samsung.com>
2016-11-13 15:54:34 -05:00
Andre Przywara
d8c0d99e66 tools: fix mksunxiboot build for tools-all target
Commit fed329aebe ("tools: add mksunxiboot to tools-all target") added
mksunxiboot to the tools-all target, but used the CONFIG_SUNXI symbol
to enable its build. Now commit aec9a0f19f ("sunxi: Rename CONFIG_SUNXI
to CONFIG_ARCH_SUNXI"), merged before that, renamed that symbol, so that
the first patch basically gets ineffective.
Adjust the symbol name in tools/Makefile to make it build again.

Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2016-11-13 15:54:15 -05:00
Tom Rini
38cacdab3b Merge branch 'master' of git://git.denx.de/u-boot-tegra 2016-11-08 10:36:57 -05:00
Stephen Warren
a8d0526133 ARM: tegra186: call secure monitor for all cache-wide ops
An SMC call is required for all cache-wide operations on Tegra186. This
patch implements the two missing hooks now that U-Boot supports them, and
fixes the mapping of "hook name" to SMC call code.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-11-07 14:36:29 -08:00
Stephen Warren
1ab557a074 armv8: add hooks for all cache-wide operations
SoC-specific logic may be required for all forms of cache-wide
operations; invalidate and flush of both dcache and icache (note that
only 3 of the 4 possible combinations make sense, since the icache never
contains dirty lines). This patch adds an optional hook for all
implemented cache-wide operations, and renames the one existing hook to
better represent exactly which operation it is implementing. A dummy
no-op implementation of each hook is provided.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-11-07 14:36:29 -08:00
Stephen Warren
b9ae6415b6 ARM: tegra: translate __asm_flush_l3_cache to assembly
When performing a cache disable function, code must not access DRAM.
That is because when the cache is disabled, it will be bypassed and all
loads and stores will be serviced by RAM. This prevents accessing any
dirty data in the cache. In turn, this means the stack cannot be
used, since that is in RAM. To guarantee that code doesn't use RAM (and
in particular the stack) __asm_flush_l3_cache() must be manually
implemented in assembly, rather than implemented in C since the compiler
won't know not to touch RAM.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-11-07 14:36:28 -08:00
Stephen Warren
6db8e17892 ARM: tegra: ensure nvtboot_boot_x0 alignment
nvtboot_boot_x0 is a 64-bit variable and hence must be 64-bit aligned.
So far this has happened by accident! Fix the code so this is guaranteed.

This fixes the following build error:
... relocation truncated to fit: R_AARCH64_LDST64_ABS_LO12_NC
    against symbol `nvtboot_boot_x0' ...

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-11-07 14:36:28 -08:00
Tom Rini
d8c4eb60f8 Merge branch 'master' of git://git.denx.de/u-boot-net 2016-11-07 13:16:00 -05:00
Siva Durga Prasad Paladugu
aa555fe9f0 net: use random ethernet address if invalid and not zero
Use random ethernet address if the ethernet address found
is invalid, not zero and config for random address
is defined.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-11-07 11:28:16 -06:00
Chris Packham
6ecf9e21b5 net: mvgbe: Fix build error with CONFIG_PHYLIB
Commit 5a49f17481 ("net: mii: Use spatch to update miiphy_register")
updated the mvgbe implementation of smi_reg_read/smi_reg_write. Prior to
that change mvgbe_phy_read and mvgbe_phy_write where used as wrappers to
satisfy the phylib APIs. Because these functions weren't updated in that
commit build errors where triggered when CONFIG_PHYLIB was enabled.

Fix these build errors by removing mvgbe_phy_read and mvgbe_phy_write
and using smi_reg_read/smi_reg_write directly.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-11-07 11:28:16 -06:00
Ash Charles
f018545ef7 net: phy: micrel: center FLP burst timing at 16ms
Like [1], reset the FLP burst timing for the KSZ9031 to the 16ms
specified by the IEEE802.3 standard from the chip's default of 8ms.

For more details, see the "Auto-Negotiation Timing" section of the
KSZ9031RNX datasheet.

[1] https://patchwork.kernel.org/patch/6558371/

Signed-off-by: Ash Charles <ash.charles@savoirfairelinux.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-11-07 11:28:16 -06:00
Stephen Warren
21622452f2 ARM: tegra: enable Ethernet on p2771-0000
Enable the Ethernet device in DT, provide board-specific configuration,
and enable the driver in Kconfig.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-11-07 11:28:16 -06:00
Stephen Warren
31c1ff90e2 ARM: tegra: add DWC EQoS (ethernet) to Tegra186 DT
Tegra186 includes a Synopsys DWC EQoS (Ethernet) device. Add this to the
Tegra186 SoC DT so that boards can make use of it.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-11-07 11:28:16 -06:00
Stephen Warren
2b950f3aea ARM: tegra: configure Ethernet address on Tegra186
On Tegra186, the bootloader which runs before U-Boot passes the Ethernet
MAC address to U-Boot using device tree. Extract this value and write it
to the environment, so that the Ethernet uclass picks it up and uses it
for the built-in Ethernet device.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-11-07 11:28:16 -06:00
Stephen Warren
86919a2306 ARM: tegra: add SoC-level hook for board_late_init()
Extend the Tegra186 implementation of board_late_init() to call a per-SoC
"hook" function. This will allow SoC-specific (rather than Tegra-wide)
functionality to be implemented without the core Tegra code needing to be
aware of the details. While board186.c is currently only used for
Tegra186, it should be applicable to any other future SoC, and perhaps its
simple design could be back-ported to older SoCs in the future too.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-11-07 11:28:15 -06:00
Stephen Warren
ba4dfef146 net: add driver for Synopsys Ethernet QoS device
This driver supports the Synopsys Designware Ethernet QoS (Quality of
Service) a/k/a eqos IP block, which is a different design than the HW
supported by the existing designware.c driver. The IP supports many
options for bus type, clocking/reset structure, and feature list. This
driver currently supports the specific configuration used in NVIDIA's
Tegra186 chip, but should be extensible to other combinations quite
easily, as explained in the source.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org> # V1
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-11-07 11:28:15 -06:00
Stephen Warren
afb970f78a dt: net: add DWC EQoS binding
The Synopsys DWC EQoS is a configurable Ethernet MAC/DMA IP block which
supports multiple options for bus type, clocking and reset structure, and
feature list.

This patch imports the binding from the Linux kernel, including my V3
patch to extend the binding to cover the Tegra186, which is applied for
next-20160912. So far, my changes have been acked by Lars Persson, the
original author of the binding.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-11-07 11:28:15 -06:00
Fabio Estevam
dac09fc10b wandboard: Make Ethernet functional again
Since commit ce412b79e7 ("drivers: net: phy: atheros: add separate
config for AR8031") ethernet does not work on mx6sabresd.

This commit correctly assigns ar8031_config() as the configuration
function for AR8031 in the same way as done in the Linux kernel.

However, on wandboard design we need some additional configuration,
such as enabling the 125 MHz AR8031 output that needs to be done
in the board file.

This also aligns with the same method that the kernel performs
the AR8031 fixup in arch/arm/mach-imx/mach-imx6q.c.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-11-06 07:40:40 -05:00
Tomeu Vizoso
0f7c6cdc81 mkimage: Allow including a ramdisk in FIT auto mode
Adds -i option that allows specifying a ramdisk file to be added to the
FIT image when we are using the automatic FIT mode (no ITS file).

This makes adding Depthcharge support to LAVA much more convenient, as
no additional configuration files need to be kept around in the machine
that dispatches jobs to the boards.

Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Matt Hart <matthew.hart@linaro.org>
Cc: Neil Williams <codehelp@debian.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-11-06 07:33:42 -05:00
Tom Rini
baade496d1 travis-ci: Try harder to build all ARM targets
The way that we have things broken down currently allows for some
combinations of vendor or CPU to not be built.  To fix this, create a
new catch-all job that excludes everything we've built elsewhere.  For
the sake of simplicity we are allowing for the possibility of some
overlap between the vendor-based jobs and the CPU-based jobs.  While
we're in here, make a failed build provide the summary of failure.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-11-06 07:33:41 -05:00
Tom Rini
e0f2406e73 buildman: Fix building based on 'options' field
The README for buildman says that we can use any field in boards.cfg to
decide what to build.  However, we were not saving the options field
correctly.

Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-11-06 07:33:41 -05:00