Commit graph

33 commits

Author SHA1 Message Date
Manikanta Guntupalli
28dc356e66 xilinx: dts: Fix open drain warning on Zynq, ZynqMP and Versal
Fix for below open drain warning on Zynq, ZynqMP and Versal reported by
Linux.
"enforced open drain please flag it properly in DT/ACPI DSDT/board
file."

Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/056b6f60f89fa2addb762669b80640cd5b31b001.1688992653.git.michal.simek@amd.com
2023-07-21 09:00:38 +02:00
Michal Simek
174d728471 arm64: zynqmp: Switch to amd.com emails
Update my and DPs email address to match current setup.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/aba5b19b9c5a95608829e86ad5cc4671c940f1bb.1688992543.git.michal.simek@amd.com
2023-07-21 09:00:38 +02:00
Ashok Reddy Soma
b8745e7eb4 arm64: zynqmp: Fix usb node drive strength and slew rate
As per design, all input/rx pins should have fast slew rate and 12mA
drive strength. Rest all pins should be slow slew rate and 4mA drive
strength. Fix usb nodes as per this and remove setting of slow slew rate
for all the usb gorup pins.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/b245c165f05845c1f3ab41a92c82b7ec1538cee4.1655288171.git.michal.simek@amd.com
2022-06-24 14:17:18 +02:00
Amit Kumar Mahapatra
6e38e2ea79 arm64: zynqmp: Set qspi tx-buswidth to 4
In all the ZynqMP boards dts files tx-buswidth is by default set to 1. Due
to this the framework only issues 1-1-1 write commands to the GQSPI driver.
But the GQSPI controller is capable of handling 1-4-4 write commands, so
updated the tx-buswidth to 4 in ZynqMP boards dts files. This would enable
the spi-nor framework to issue 1-4-4 write commands instead of 1-1-1. This
will increase the tx data transfer rate, as now the tx data will be
transferred on four lines instead on single line.

Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/ad61199f55e5e00f29de6206d9d1872a52a7657e.1652193179.git.michal.simek@amd.com
2022-05-18 13:17:18 +02:00
Manish Narani
15ca9ebb07 arm64: zynqmp: Move USB3 PHY properties from DWC3 node to USB node
Move the PHY properties from DWC3 node to USB node in ZynqMP DTs as here
the USB3 PHY used is PSGTR, which is connected to Xilinx USB core. This
PHY initialization should be handled from Xilinx USB core as the
prerequisite register configurations are done here only.

Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-07-26 09:26:41 +02:00
Michal Simek
9899f3e6b9 arm64: zynqmp: Add psgtr description to zc1751 dc1 board
Wire psgtr for zc1751 dc1 board.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:36 +02:00
Michal Simek
52caf2c12b arm64: zynqmp: Remove gpio from aliases list
It is not recommended to have aliases for gpio. In past it was used in
Linux for assigning numbers via sysfs which is deprecated and libgpiod
should be used instead.
In U-Boot this number is used for seq number but gpio offset are not
counted from this number. That's why having these aliases only for seq
number is not needed. As is done in Linux it is the best to use full gpio
name instead of sequence number which depends on sequence in binding.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:36 +02:00
Michal Simek
6a2ce6ec24 arm64: zynqmp: Sync psgtr location on zcu104/zcu111/zc1751-dc1
psgtr node should be below pinctrl for easier comparion among dts files.
That's why move that nodes to different location.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
70fbcdb825 arm64: zynqmp: Remove addition newline from zc1751 dc1
Trivial patch.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
184309b8c6 arm64: zynqmp: Add maximum-speed property for dwc3 nodes
dwc3 can be used only for higher speeds than super-speed that's why
explicitly set it up.
This is also aligned with other ZynqMP dts files.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
447fb8db02 arm64: zynqmp: Update Copyright years to 2021
Trivial change for all files I have touched recently.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
3195840c94 arm64: zynqmp: Add psgtr DT descriptions
Mainline kernel has psgtr driver that's why it is good to add description
to DT files. Some boards are just missing description for USB3 and sata.
zc1751-dc1 and p-a2197 are also missing clock descriptions for input
clocks.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-05-19 09:44:50 +02:00
Michal Simek
bd00849ae9 arm64: zynqmp: Add pinctrl description
ZynqMP pinctrl Linux driver has been merged to 5.13-rc1 kernel. Based on it
DT files can be extended by pinctrl configurations.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-05-19 09:44:50 +02:00
Michal Simek
ce90654d1c xilinx: Sync DTs with Linux kernel
There are several changes which happen in mainline kernel which should get
also to U-Boot. Here is the list of patches from the kernel:

- ARM: zynq: Fix leds subnode name for zc702/zybo-z7
- arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
- arm64: dts: zynqmp: Fix u48 si5382 chip on zcu111
- arm64: dts: zynqmp: Wire up the DisplayPort subsystem
- arm64: dts: zynqmp: Add DisplayPort subsystem
- arm64: dts: zynqmp: Add DPDMA node
- arm64: dts: zynqmp: Enable phy driver for Sata on zcu102/zcu104/zcu106
- arm64: dts: zynqmp: Enable si5341 driver for zcu102/106/111
- arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106
- arm64: dts: zynqmp-zcu100-revC: correct interrupt flags
- arm64: dts: xilinx: align GPIO hog names with dtschema
- arm64: zynqmp: Add Xilinx AES node
- dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA

but also some other changes have been done.
- Using only one compatible string for adxl345 on zturn
- Remove Xilinx internal DP bindings
- Remove USB3.0 serdes configurations
- Remove SATA serdes configuration for zc1232
- Resort nvmem_firmware
- Update nand compatible string
- Aling power-domains property for sd0/1

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-03-30 12:03:24 +02:00
Michal Simek
01a6da1661 xilinx: Fix xlnx,mio_bank property
s/xlnx,mio_bank/xlnx,mio-bank/g

DT binding is describing mio-bank not mio_bank that's why fix all DTSes and
also driver itself.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
2020-08-20 09:49:20 +02:00
Michal Simek
5df63a60aa arm64: zynqmp: Fix addresses in partition definitions
Node name should be <name>@<address> which is not how partitions are
described.

Issue was found by running dtbs_check as:
flash@0: 'partition@qspi-device-tree', 'partition@qspi-fsbl-uboot',
'partition@qspi-linux', 'partition@qspi-rootfs'
do not match any of the regexes: ...

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-06 12:51:31 +02:00
Michal Simek
04437dea7c arm64: zynqmp: Sync DP subsystem
Sync DP subsystem with the latest state in Xilinx U-Boot repository.
This binding hasn't been approved in mainline Linux but it is much better
than ancient version which this patch removes.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-06 12:51:31 +02:00
Manish Narani
12ffe75819 arm64: zynqmp: Add 'no-1-8-v' property for ZynqMP Boards
Modify dts files to add 'no-1-8-v' property for all the ZynqMP boards.
User can remove this property to enable the UHS mode. This is to keep
the same speed (HS) modes across all the stages of the Linux Boot. Due
to power cycling limitation of some of the ZynqMP boards, some SD cards
don't get power cycled and are failing in Linux.

Signed-off-by: Manish Narani <manish.narani@xilinx.com>
2020-04-06 12:51:31 +02:00
Michal Simek
d31f1c9236 arm64: zynqmp: Update Copyright years to 2020
Trivial change.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-06 12:51:31 +02:00
Michal Simek
2975a42b42 arm64: zynqmp: Use ethernet-phy as node name for ethernet phys
Ethernet phys based on devicetree specification should be using
ethernet-phy@ node name instead of pure phy@.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:01 +02:00
Neil Armstrong
ffd4c7c2ec dts: switch spi-flash to jedec, spi-nor compatible
There is no reason not to use the Linux "jedec,spi-nor" binding in U-Boot
dts files. This compatible has been added in sf_probe, let use it.

This patch switches to jedec,spi-nor when spi-flash is used in the DTS
and DTSI files, and removed spi-flash when jedec,spi-nor is already
present.

The x86 dts are switched in a separate commit since it depends on a change
in fdtdec.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Evgeniy Paltsev <paltsev@synopsys.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Patrick Delaunay <Patrick.delaunay@st.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2019-04-12 10:54:27 +05:30
Michal Simek
0ed45f0025 arm64: zynqmp: Wire spi-flash compatible string with flashes
Enable reading tx and rx buswidth from DT via spi-uclass.
To get these from uclass spi-flash compatible string has to be added
to flash node.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-11-29 10:30:02 +01:00
Michal Simek
43bf439472 arm64: zynqmp: Add eeprom reference to eeprom nodes
eeprom can contain information which can be used by nvmem drivers.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09 12:14:48 +02:00
Michal Simek
098505f500 arm64: zynqmp: Use atmel prefix instead of at
This changes was done in mainline and this patch is just following it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09 12:14:48 +02:00
Michal Simek
52af7e3e81 arm64: zynqmp: Remove additional comments from dts files
Remove additional comments which were removed as the part of upstreaming.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09 12:14:48 +02:00
Michal Simek
18a952ce7f arm64: zynqmp: Sync up license with mainline kernel
Mainline Linux kernel has adopted SPDX header license in a different
format then was used before. This patch is syncing it up.

Also update years in License text and remove Nathalie's email because it
is no longer valid.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09 12:14:47 +02:00
Michal Simek
ee4983f73a arm64: zynqmp: Convert board to use zynqmp-clk driver
Use zynqmp clock driver instead of fixed clocks.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-23 09:30:44 +01:00
Michal Simek
858a508f49 arm64: zynqmp: Remove undocumented dma properties
Remove overfetch, ratectrl, include-sg and src-issue dma properties.
Driver is not using them and they are also not documented in the binding
doc.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Kedareswara rao Appana <appanad@xilinx.com>
2017-12-14 20:08:33 +01:00
Michal Simek
6507be7800 arm64: zynqmp: Remove local-mac-address from dtsi file
Generic dtsi file can't use the same mac address for all.
U-Boot read mac from eeprom in zcu102 case and for others random mac
address is generated.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:09 +01:00
Michal Simek
8925e5996d ARM64: zynqmp: Fix usb nodes for dc1 and dc2
Fix DT binding for usb nodes. Setup correct aliases and enable dwc3
nodes.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-01-10 10:18:12 +01:00
Sai Krishna Potthuri
0488a5e117 ARM64: zynqmp: change sdhci compatible string.
This patch changes the compatible string for sdhci node,
adds "xlnx,device_id" and "xlnx,mio_bank" property to sdhci node.

Signed-off-by: Sai Krishna Potthuri <lakshmis@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15 15:30:40 +01:00
Michal Simek
c926e6fbb6 ARM64: zynqmp: Remove DTC 1.4.2 warnings
DTC 1.4.2 reports these warnings:
Warning (unit_address_vs_reg): Node /amba_apu has a reg or ranges
property, but no unit name
Warning (unit_address_vs_reg): Node /amba has a reg or ranges property,
but no unit name
Warning (unit_address_vs_reg): Node /amba/usb@fe200000 has a unit name,
but no reg property
Warning (unit_address_vs_reg): Node /amba/usb@fe300000 has a unit name,
but no reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-video0channel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-video1channel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-video2channel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-graphicschannel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-audio0channel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-audio1channel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node /memory has a reg or ranges
property, but no unit name

This patch is fixing them.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-11-15 15:30:38 +01:00
Michal Simek
6c0c958de8 ARM64: zynqmp: Add support for zc1751 with DC cards
Support ZynqMP zc1751 with DC cards.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:06 +02:00