- Use TF-A on imx8mp_beacon to fix boot regression.
- Use latest 6.8 dts for imx8mp_beacon.
- Fix the RAM initialization for phycore_imx8mp PCL-070 rev 1.
- Describe the 0087 i.mx8m mini product variant in tdx-cfg-block.
The device tree has evolved over time, so re-sync. This also
partial reverts one change on the PCIe, because U-Boot doesn't
have a proper driver. However, since the clock is configured
to generate a 100MHz reference clock by default, a proper driver
isn't really necessary.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
When the board was originally added, it enabled some features which
allowed it to bypass Trusted Firmware, but as the feature set of
Linux grew and more features became available, the U-Boot config
options which bypassed TF-A caused issues, so it needs to return
to the standard operating mode of using TF-A or the system no
longer boots.
Fixes: ab53bd43db ("arm64: imx: Add support for imx8mp-beacon-kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
We need to differ between PCL-070 and PCM-070. PCL-070 supports 2GHz RAM
timings from pcb rev 1 or newer. PCM-070 supports 2GHz RAM timings from
pcb rev 3 or newer.
Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
In case the PHY is fully described in DT, use PHY MDIO address
from DT directly instead of always using auto-detection. This
also fixes the behavior of 'mdio list' in such DT setup, which
now prints the PHY connected to the MAC correctly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
One fix makes the reboot more robust on some older board, another one
stabilises the initial clock setup on the A10/A20.
Two patches make sure our DRAM init does not actually change the content
of the DRAM array, which allows to use DRAM for Linux' pstore
functionality.
We get SPI support for U-Boot proper for one more SoC, that patch was
lingering around for a while, and should not affect other SoCs, so I am
merging this now.
As an added bonus, we get the defconfig file for a new board, the DT was
already synced from the kernel tree.
The CI looked happy with changes, and I tested them on five different
boards with different SoCs.
A RNG driver for Armada 3720 boards running the Turris Mox rWTM firmware
from CZ.NIC in the secure processor.
Signed-off-by: Max Resch <resch.max@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add a config fragment with required differences for booting from spi
flash instead of sd-card (default).
Settings for environment location are based on vendor u-boot:
https://github.com/kobol-io/u-boot/blob/helios4/include/configs/helios4.h#L59
The fragment can be applied on top of helios4_defconfig by make:
make helios4_defconfig spiboot.config
Signed-off-by: Josua Mayer <josua@solid-run.com>
Update the helios4 defconfig to enable the 'setexpr' command, which is a
default and useful for various complex boot-scripts.
Signed-off-by: Josua Mayer <josua@solid-run.com>
SolidRun Armada-388 SoM has an i2c bus supporting on-som eeprom, and
peripherals on a carrier.
armada-38x.dtsi disables this bus by default, it should be enabled by
som or carrier dts.
Linux has moved i2c0 from helios-4 board dts to som dtsi, including
status, pinctrl and clock speed.
Copy these settings from mainline.
This fixes accessing i2c bus from u-boot commandline.
Signed-off-by: Josua Mayer <josua@solid-run.com>
The Turris Omnia contains the Marvell 88E6176 ethernet switch. Add
config options and device tree to enable the support.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Signed-off-by: Marek Behún <kabel@kernel.org>
The mv88e6xxx driver does not currently initialize the smi_addr field, but
instead keeps the default zero value. This leads to driver being unusable
on devices where the switch is not on address zero of the mdio bus. Fix
this problem by reading the SMI address from device tree.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Current sunxi DRAM initialisation code does several test accesses to the
DRAM array to detect aliasing effects and so determine the correct
row/column configuration. This changes the DRAM content, which breaks
use cases like soft reset and Linux's ramoops mechanism.
Fix this problem by saving and restoring the content of the DRAM cells
that is used for the test writes.
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
mctl_mem_matches and mctl_mem_matches_base identical functions. To
avoid code duplication move them to dram_helpers and make
mctl_mem_matches use generic mctl_mem_matches_base.
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
No device tree in U-Boot or linux use the wrong spelling used in code.
Use correct property name as defined in dwc3 bindings.
Fixes: 062790f461 ("usb: xhci-dwc3: Add USB2 PHY configuration")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marex@denx.de>
Because of commit bf947d2a4b ("imx6ul: synchronise device tree with
linux"), the compatible property of lcdif in imx6ul.dtsi went from
compatible = "fsl,imx6ul-lcdif", "fsl,imx28-lcdif";
to
compatible = "fsl,imx6ul-lcdif", "fsl,imx6sx-lcdif";
without updating the mxsfb driver to match that change.
Add "fsl,imx6sx-lcdif" as a compatible id to fix that.
Fixes: bf947d2a4b ("imx6ul: synchronise device tree with linux")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Commit 5d7a95f499 ("imx6ul/imx6ull: synchronise device trees with
linux") removed the display timings from the board device tree whereas
they are still needed by the mxsfb driver.
Add the timings back (the correct ones) in the
imx6ul-opos6uldev-u-boot.dtsi file and remove them from the
opos6uldev.env file.
Update the opos6uldev_defconfig file so that the LCD turns on at boot.
Fixes: 5d7a95f499 ("imx6ul/imx6ull: synchronise device trees with linux")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Use the latest, mx93a1-ahab-container.img that is compatible with the
i.MX93 A1 revision.
Using mx93a1-ahab-container.img on an A0 chip and conversely causes a boot
failure without any traces on the UART.
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
If the optional `tee.bin` OP-TEE binary is missing, the image will still be
functional. Adapt the warning message accordingly.
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
The OrangePi Zero 2W is a tiny development board featuring the Allwinner
H618 SoC, shipping with up to 4GB of LPDDR4 DRAM, a mini-HDMI connector,
two USB Type-C sockets and a 16MB SPI NOR flash.
There is an FPC connector to connect an expansion board, which sports
two more USB Type-A sockets and a 100MBit Ethernet port. Support for
the expansion board is not in the DT yet, probably a DT overlay would
cover this in the future.
Add a defconfig file selecting the right drivers and DRAM options.
Since the .dts file was synced from the Linux kernel repo already, we
just need to add one line to the Makefile to actually build the .dtb.
The DRAM parameters were derived from the values found in the BSP DRAM
drivers on the SPI NOR flash.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
This delay is required after switching the clock source.
See “A20 Reference manual v1.4” Page 50 / section
“1.5.4.16. CPU/AHB/APB0 CLOCK RATIO”: “If the clock
source is changed, at most to wait for 8 present running
clock cycles.”
This is already implemented in clock_set_pll1(), but was
still missing in clock_init_safe().
Signed-off-by: Ludwig Kormann <ludwig.kormann@ict42.de>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
This change fix reboot, both configurations
were tested on my Olimex A20 Micro Rev E with debian-12.
This issue was also present and fixed on A20 Lime2 (in 8311e84b18),
quoting Olliver Schinagl:
The lime2 features a too large capacitor on the LDO3 output, which
causes the PMIC to shutdown when enabling power. To be able to still
boot up however, we must gradually enable power on LDO3 for this board.
We do this by enabling both the inrush quirk and the maximum slope the
AXP209 supports.
Link: https://bugs.debian.org/1060752
Cc: Olliver Schinagl <oliver@schinagl.nl>
Cc: Priit Laes <plaes@plaes.org>
Cc: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Philippe Coval <rzr@users.sf.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
These SoCs have two SPI controllers that are quite similar to the SPI
on previous Allwinner SoCs. The main difference is that new SoCs
don't have a clock divider (SPI_CCR register) inside SPI IP.
Instead SPI sample mode should be configured depending on the input clock.
For now SPI input clock source selection is not supported by this driver,
and only HOSC@24MHz can be used as input clock. Therefore, according to
the, manual we could change the SPI sample mode from delay half
cycle(default) to normal.
This patch adds a quirk for this kind of SPI controllers
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Tested-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Marek Vasut <marek.vasut+renesas@mailbox.org> says:
Rename R-Mobile to Renesas all over the place because the chips are
made by Renesas, while only a subset of them is from the R-Mobile line.
Add new renesas entry and update rmobile entry to match.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Rename rmobile_is_gen3_mmc0() to rcar_is_gen3_mmc0() because
this particular function is specific to Renesas R-Car Gen3.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Fix up remains of rename from rmobile to renesas,
namely file paths and remaining RMOBILE strings.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Rename arch-rmobile to arch-renesas and mach-rmobile to mach-renesas
because all the chips are made by Renesas, while only a subset of
them is from the R-Mobile line.
Use the following command to perform the rename, with manual move of
the directories using git mv and manual fix up to arch/arm/Makefile:
"
$ git grep -l '\<\(arch\|mach\)-rmobile\>' | \
xargs -I {} sed -i 's@\<\(arch\|mach\)-rmobile\>@\1-renesas@g' {}
$ sed -i 's@rmobile@renesas@' board/*/*/Kconfig
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Rename ARCH_RMOBILE to ARCH_RENESAS because all the chips are made
by Renesas, while only a subset of them is from the R-Mobile
line.
Use the following command to perform the rename:
"
$ git grep -l 'ARCH_RMOBILE' | xargs -I {} sed -i 's@ARCH_RMOBILE@ARCH_RENESAS@g' {}
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Rename rmobile.h to renesas.h because all the chips are made
by Renesas, while only a subset of them is from the R-Mobile
line.
Use the following command to perform the rename:
"
$ git grep -l 'include.*rmobile.h' | \
xargs -I {} sed -i '/include.*rmobile.h/ s@rmobile.h@renesas.h@g' {}
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Rename CONFIG_ARCH_RMOBILE_EXTRAM_BOOT to CONFIG_RMOBILE_EXTRAM_BOOT
because the former symbol does not exist and it is only incorrectly
converted CONFIG_RMOBILE_EXTRAM_BOOT which does exist. Replace the
RMOBILE with RENESAS because all the chips are made by Renesas, while
only a subset of them is from the R-Mobile line.
Use the following command to perform the rename with manual Kconfig.32 fix:
"
$ sed -i 's@CONFIG_ARCH_RMOBILE_EXTRAM_BOOT@CONFIG_RMOBILE_EXTRAM_BOOT@g' board/renesas/*/*
$ sed -i 's@CONFIG_RMOBILE_EXTRAM_BOOT@CONFIG_RENESAS_EXTRAM_BOOT@g' board/renesas/*/*
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Rename ARCH_RMOBILE_BOARD_STRING to ARCH_RENESAS_BOARD_STRING
because all the chips are made by Renesas, while only a subset
of them is from the R-Mobile line.
Use the following command to perform the rename:
"
$ git grep -l 'ARCH_RMOBILE_BOARD_STRING' | \
xargs -I {} sed -i 's@ARCH_RMOBILE_BOARD_STRING@ARCH_RENESAS_BOARD_STRING@g' {}
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Rename rmobile_get_prr() to renesas_get_prr() because all the
chips are made by Renesas, while only a subset of them is from
the R-Mobile line.
Use the following command to perform the rename:
"
$ git grep -l '\<rmobile_get_prr\>' | \
xargs -I {} sed -i 's@\<rmobile_get_prr\>@renesas_get_prr@g' {}
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Simplify the weak symbols use in cpu_info.c by using the __weak macro.
The result is identical, but the syntax is much simpler. Furthermore,
drop three more rmobile* symbols which are now unused.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Rename rmobile_cpuinfo[] to renesas_cpuinfo[] because all
the chips are made by Renesas, while only a subset of them
is from the R-Mobile line.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Rename rmobile_cpuinfo_idx() to renesas_cpuinfo_idx() because all
the chips are made by Renesas, while only a subset of them is from
the R-Mobile line.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Rename RMOBILE_CPU_TYPE_* to RENESAS_CPU_TYPE_* because all
the chips are made by Renesas, while only a subset of them is
from the R-Mobile line.
Use the following command to perform the rename:
"
$ git grep -l '\<RMOBILE_CPU_TYPE_[A-Z0-9]\+\>' | \
xargs -I {} sed -i 's@\<RMOBILE\(_CPU_TYPE_[A-Z0-9]\+\)\>@RENESAS\1@g' {}
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Rename rmobile_get_cpu_rev_*() to renesas_get_cpu_rev_*() because
all the chips are made by Renesas, while only a subset of them is
from the R-Mobile line.
Use the following command to perform the rename:
"
$ git grep -l '\<rmobile_get_cpu_rev_\(integer\|fraction\)\>' | \
xargs -I {} sed -i 's@\<rmobile_get_cpu_rev_\(integer\|fraction\)\>@renesas_get_cpu_rev_\1@g' {}
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Rename rmobile_get_cpu_type() to renesas_get_cpu_type() because
all the chips are made by Renesas, while only a subset of them
is from the R-Mobile line.
Use the following command to perform the rename:
"
$ git grep -l '\<rmobile_get_cpu_type\>' | \
xargs -I {} sed -i 's@\<rmobile_get_cpu_type\>@renesas_get_cpu_type@g' {}
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
This file is no longer used, the PFC pin controller driver is
superseded by drivers/pinctrl/renesas/pfc-r8a7790.c which
includes all the details of the hardware. Remove this file.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
This file is no longer used, the MMCIF controller driver is
superseded by drivers/mmc/sh_mmcif.c which includes all the
details of the hardware. Remove this file include from all
board files and remove the file itself. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
This file is no longer used, the SDHI controller driver is long
superseded by drivers/mmc/renesas-sdhi.c which includes all the
details of the hardware. Remove this file include from all board
files and remove the file itself. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Last board with this SoC has been removed in commit
0fb054b3f7 ("arm: Remove armadillo-800eva board")
in August 2022. Drop the rest of unused code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
