Layerscape began to use two eSDHC controllers, for example,
LS1012A. They are same IP block with same reference clock.
This patch is to add clock support for the second eSDHC.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
As per LS1046A hardware manual, SGMII.9 and SGMII.10 present on
lane D and lane C respectively for 0x3363 protocol.
So fix serdes1 settings for ls1046a.
Signed-off-by: Maciej Pijanowski <maciej.pijanowski@3mdeb.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Fixes a link error on layerscape platform, linking fails with CONFIG_PCI
set and CONFIG_PCI_LAYERSCAPE unset.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Change bootcmd update logic when CONFIG_ENV_ADDR is not defined
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Update qspi clock configuration in TFABOOT in case
of all boot sources except qspi boot source.
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Flushing L3 cache may need variable time depending upon cache line
allocation.
Coming up with a proper timeout value would be best handled by
simulations under multiple scenarios in your actual system.
>From the purely HN-F point of view, the flush would take ~15 cycles for
a clean line, and ~22 cycles for a dirty line. For the dirty line case,
there are many variables outside the HN-F that will increase the
duration per line. For example, a *DBIDResp from the SN-F/SBSX,
memory controller latency, SN-F/SBSX RetryAck responses, CCN ring
congestion, CCN ring hops, etc, etc. The worst-case timeout would
have to factor in all of these variables plus the HN-F cycles for
every line in the L3, and assuming all lines are dirty
In case if L3 is not flushed properly, system behaviour will be
erratic, so remove timeout and add loop to check status of L3 cache.
System will stuck in while loop if there is some issue in L3 cache
flushing.
Signed-off-by: Udit Kumar <udit.kumar@nxp.com>
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Layerscape began to use two eSDHC controllers, for example,
LS1028A. They are same IP block with same reference clock.
This patch is to add clock support for the second eSDHC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Rx Compliance tests may fail intermittently at high jitter
frequencies using default register values.
So program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Enable workaround for USB erratum A-008997. Here PCSTXSWINGFULL
registers has been moved to DSCR as compared to other Layerscape SoCs
where it was in SCFG.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
ENVL_NOWHERE is dependent on CONFIG_ENV_IS_NOWHERE and not on
CONFIG_CHAIN_OF_TRUST so return ENVL_NOWHERE when CONFIG_ENV_IS_NOWHERE
is enabled
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
LS1028A is an ARMv8 implementation. LS1028ARDB is an evaluation
platform that supports the LS1028A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@nxp.com>
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The LX2160A PCIe is using driver PCIE_LAYERSCAPE_GEN4 instead
of PCIE_LAYERSCAPE.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The lx2160a have up to 6 PCIe controllers and have different
address and size of PCIe region.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Change to use PCIe address macro to determine if precompile the PCIe
MMU table entry.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
This is fix to:
e2a12f590d rockchip: use 'arch-rockchip' as header file path
The V2 of origin patch set has fix this, but we merge V1 by
mistake, so lets correct it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
On AM654 SoC(arm64) which is IO coherent and has L3 Cache, cache
maintenance operations being done to support non-coherent platforms
causes issues.
For example, here is how U-Boot prepares/handles a buffer to receive
data from a device (DMA Write). This may vary slightly depending on the
driver framework:
Start DMA to write to destination buffer
Wait for DMA to be done (dma_receive()/dma_memcpy())
Invalidate destination buffer (invalidate_dcache_range())
Read from destination buffer
The invalidate after the DMA is needed in order to read latest data from
memory that’s updated by DMA write. Also, in case random prefetch has
pulled in buffer data during the “wait for DMA” before the DMA has
written to it. This works well for non-coherent architectures.
In case of coherent architecture with L3 cache, DMA write would directly
update L3 cache contents (assuming cacheline is present in L3) without
updating the DDR memory. So invalidate after “wait for DMA” in above
sequence would discard latest data and read will cause stale data to be
fetched from DDR. Therefore invalidate after “wait for DMA” is not
always correct on coherent architecture.
Therefore, provide a Kconfig option to disable cache maintenance ops on
coherent architectures. This has added benefit of improving the
performance of DMA transfers as we no longer need to invalidate/flush
individual cache lines(especially for buffer thats several KBs in size).
In order to facilitate use of same Kconfig across different
architecture, I have added the symbol to top level arch/Kconfig file.
Patch currently disables cache maintenance ops for arm64 only.
flush_dcache_all() and invalidate_dcache_all() are exclusively used
during enabling/disabling dcache and hence are not disabled.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
rockchip platform header file is in 'arch-rockchip'
instead of arch-$(SOC) for all SoCs.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This fixes relaction isses with the PSCI_TABLE entries in
the psci_32_table and psci_64_table.
When using 32-bit adress pointers relocation was not being applied to
the tables, causing PSCI handlers to point to the un-relocated code
area. By using 64-bit data relocation is properly applied. The
handlers are thus in the "secure data" area, which is protected by
/memreserve/ in the FDT.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
HVC call makes use of 6 mandatory arguments rather than 7 in the same way
as SMC calls. The 7th argument is optional (Client ID) for both HVC and
SMC but is implemented as 16-bit parameter and register R7 or W7. The aim
of this patch is just fix compilation error due to an invalid asm code in
the HVC call so that's why the 7th argument is removed.
The issue does not report any error in a normal build as hvc_call is not
used at all and is optimized by the compiler. Using -O0 triggers the
error so the patch is intended to fix issues on a ongoing effor to build
U-Boot with -O0.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
When PSCI is enabled, we are expecting U-Boot which now act
as EL3 software will handle all the PSCI calls. We won't need
fwcall as no further HVC or SMC are needed.
Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
Allow PSCI layer to handle any SiP service functions added by
platform vendors. PSCI layer will look for SiP service function
in the SiP function table located in '._secure_svc_tbl_entries'
section if the SMC function identifier is not found in the PSCI
standard functions table. Use DECLARE_SECURE_SVC macro to declare
and add platform specific SiP service function.
This new section '._secure_svc_tbl_entries' is located next to
'._secure.text' section. Refer to arch/arm/cpu/armv8/u-boot.lds.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Commit 1416e2d225 ("armv8: make SPL exception vectors optional") had a
typo in it which effectively disabled exception handling in SPL code always.
Since nobody complained, I guess we may as well disable exception handling
in SPL always by default.
So fix the bug to make the config option effective, but disable exception
handling in SPL by default. This gets us to the same functionality as before
by default, but with much less code included in the binary.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
The SEC QI ICID setup in the QIIC_LS register is actually an offset
that is being added to the ICID coming from the qman portal. Setting
it with a non-zero value breaks SMMU setup as the resulting ICID is
not known. On top of that, the SEC QI ICID must match the qman portal
ICIDs in order to share the isolation context.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
remove SCSI and SCSI_AHCI configs for ls1043ardb due to no sata interface
support.
this changed is to fixed the ls1043ardb compile warning as fallows:
===================== WARNING ======================
This board does not use CONFIG_DM_SCSI. Please update
the storage controller to use CONFIG_DM_SCSI before the
v2019.07 release. Failure to update by the deadline may
result in board removal.See doc/driver-model/MIGRATION.txt
for more info.
====================================================
Signed-off-by: Peng Ma <peng.ma@nxp.com>
[PK: reword the patch subject]
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Moves FSL_TZASC_400 and FSL_TZPC_BP147 configs to Kconfig
for LS1088A and LS2088A platforms.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
LX2160AQDS is a development board that supports LX2160A
family SoCs. This patch add base support for this board.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[PK: Sqaush patch for "secure boot defconfig" & add maintainer]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
some dpmacs in armv8a based freescale layerscape SOCs can be
configured via both serdes(sgmii, xfi, xlaui etc) bits and via
EC*_PMUX(rgmii) bits in RCW.
e.g. dpmac 17 and 18 in LX2160A can be configured as SGMII from
serdes bits and as RGMII via EC1_PMUX/EC2_PMUX bits
Now if a dpmac is enabled by serdes bits then it takes precedence
over EC*_PMUX bits. i.e. in LX2160A if we select serdes protocol
that configures dpmac17 as SGMII and set the EC1_PMUX as RGMII,
then the dpmac is SGMII and not RGMII.
Therefore, move the fsl_rgmii_init after fsl_serdes_init. in
fsl_rgmii_init function of SOC, we will check if the dpmac is enabled
or not? if it is (fsl_serdes_init has already enabled the dpmac), then
don't enable it.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add code to initial ethernet interface arrays
with corresponding dpmac-id values in serdes_init function
for LX2160A.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Commit 81ea00838c ("efi_loader: PSCI reset and shutdown") put the SMCCC
assembly code into the efi specific code section. This is wrong when we
do not have EFI_LOADER enabled, as that strips efi runtime sections from
the output binary
Reported-by: Michal Simek <monstr@monstr.eu>
Reported-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Tested-by: Michal Simek <monstr@monstr.eu>
Fixes: 81ea00838c ("efi_loader: PSCI reset and shutdown")
Signed-off-by: Alexander Graf <agraf@suse.de>
Refactor the switch from supervisor to hypervisor to a new function called
at the beginning of do_bootefi().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Make use of "IMAGE_MAX_SIZE" and "IMAGE_TEXT_BASE" rather than
CONFIG_SPL_MAX_SIZE and CONFIG_SPL_TEXT_BASE. This lets us re-use the
same script for both SPL and TPL. Add logic to scripts/Makefile.spl to
pass in the right value when preprocessing the script.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850evm & omap3_logic_somlv
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Similar changes was done for Zynq in past and this patch just follow
this pattern to separate cpu code from SoC code.
Move arch/arm/cpu/armv8/zynqmp/* -> arch/arm/mach-zynqmp/*
And also fix references to these files.
Based on
"ARM: zynq: move SoC sources to mach-zynq"
(sha1: 0107f24036)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is hard dependency for CLK_ZYNQMP to have zynqmp_pmufw_version()
but also FPGA code is calling this function which is possible to use
without actual CLK_ZYNQMP firmware driver to be enabled.
This patch enables the case where only fixed-clock CLK setup is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
On LS1043A rev1.0 there are 4 interrupt pins for INTx, and on
rev1.1 there is only 1 for INTx, so the current fixup is inverse
of the fact.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1043A/LS1023A 23x23 package silicon has different SVR:VAR_PER.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls2088ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- remove EL3 specific erratas for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1088ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- MC address changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- ifc chip select changes for TFABOOT
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Fixes for TFABOOT framework
- update eMMC bootsrc to SD_MMC
- Increase buffer size for mcinitcmd from 256 to 512
- Fix mcinitcmd and bootcmd for Secure Boot
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add Kconfig option WATCHDOG_RESET_DISABLE to disable watchdog reset
in imx_watchdog driver, so that the watchdog will not be fed in
u-boot if CONFIG_WATCHDOG_RESET_DISABLE is enabled.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Support watchdog driver for fsl-lsch2. It's disabled in default.
If you want to use it, please enable CONFIG_IMX_WATCHDOG.
Define CONFIG_WATCHDOG_TIMEOUT_MSECS to set watchdog timeout.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
