Neural Compute Module 6(Neu2) is a 96boards SoM-CB compute module
based on Rockchip RK3588 from Edgeble AI.
General features:
- Rockchip RK3588
- up to 32GB LPDDR4x
- up to 128GB eMMC
- 2x MIPI CSI2 FPC
On module WiFi6/BT5 is available in the following Neu6 variants.
Neu6 needs to mount on top of associated Edgeble IO boards for
creating complete platform solutions.
Enable eMMC for now to boot Linux successfully.
commit <3d9a2f7e7c5e> ("arm64: dts: rockchip: rk3588: Add Edgeble Neu6
Model A SoM")
Add support for Edgeble Neu6 Model A SoM.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This initial version supports CPU, dma, interrupts, timers, UART and
SDHCI (everything necessary to boot Linux on this system on chip) as
well as Ethernet, I2C, PWM and SPI.
The DT is split into rk3588 and rk3588s, which is a reduced version
(i.e. with less peripherals) of the former.
commit <9fb232e9911f> (" arm64: dts: rockchip: Add base DT for rk3588
SoC")
commit <d68a97d501f8> ("arm64: dts: rockchip: Add rk3588 pinctrl data")
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add IOC unit header include for rk3588.
Signed-off-by: Steven Liu <steven.liu@rock-chips.com>
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add ddr driver for rk3588 to get the ram capacity.
Co-developed-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add RK3588 pll set and get rate clock support.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add clock driver support for Rockchip RK3588 SoC.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add the dt-bindings header for the Rockchip RK3588, that gets
shared between the clock controller and the clock references
in the dts.
commit <f204a60e545c> ("dt-bindings: clock: add rk3588 clock
definitions")
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add clock and reset unit header include for rk3588.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for rk3588 package header in mkimage tool.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update the MAINTAINERS file to include the devicetree for the
rk3568-evb1-v10 board.
Also update Rockchip board docs to include information on building
RK3568 based devices.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add gpio-ranges property to GPIO nodes so that the bank ID can
be correctly derived for each GPIO bank.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
It enables automatic clock gating on idle, disables the eDP phy by
default, and sets the core pvtpll ring length. It is reported this
lowers the temperature on at least one SoC by 7C.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable spl to detect which device it was booted from.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3566 and rk3568 from the mainline Linux kernel (6.2-rc2 as of
this writing).
Note that this will rename the rk3568-evb to rk3568-evb1-v10.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the gpio-ranges property to each GPIO node for use in deriving
the correct bank ID. Note that invoking "gpio status -a" no longer
causes the board to hit a "Synchronous Abort".
Fixes: 537b1a2774 ("rockchip: add px30 devicetrees")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Use the new devicetree property of gpio-ranges to determine the GPIO
bank ID. Preserve the "old" way of doing things too, so that boards
can be migrated and tested gradually (I only have a 3566 and 3326 to
test).
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
=> usb start
starting USB...
Bus usb@fd000000: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus usb@fd800000: USB EHCI 1.00
scanning bus usb@fd000000 for devices... cannot reset port 1!?
2 USB Device(s) found
scanning bus usb@fd800000 for devices... 4 USB Device(s) found
scanning usb for storage devices... 2 Storage Device(s) found
=> usb tree
USB device tree:
1 Hub (5 Gb/s, 0mA)
| U-Boot XHCI Host Controller
|
+-2 Mass Storage (5 Gb/s, 224mA)
SanDisk Dual Drive 04019c9b2e1a58f24ee318c3c123aa5
1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Hub (480 Mb/s, 100mA)
| USB 2.0 Hub
|
+-3 Mass Storage (480 Mb/s, 500mA)
| JetFlash Mass Storage Device 19M7I4ZQFTSC08SU
|
+-4 Human Interface (12 Mb/s, 98mA)
Logitech USB Receiver
Co-developed-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
combphy1 is failing to probe due to unhandled assigned-clocks and
assigned-clocks-rates.
=> usb start
starting USB...
Bus usb@fd000000: Failed to get PHY1 for usb@fd000000
Port not available.
Bus usb@fd800000: USB EHCI 1.00
There is no real requirement for them in U-Boot to handle, hence
mark them as deleted-properties for the probe to success
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RK3568 has two USB 2.0 PHYs, and each PHY has two ports, the OTG port
of PHY0 support OTG mode with charging detection function, they are
similar to previous Rockchip SoCs.
However, there are three different designs for RK3568 USB 2.0 PHY.
1. RK3568 uses independent USB GRF module for each USB 2.0 PHY.
2. RK3568 accesses the registers of USB 2.0 PHY IP directly by APB.
3. The two ports of USB 2.0 PHY share one interrupt.
This patch only PHY1 with necessary attributes required to function
USBPHY1 on U-Boot.
Co-developed-by: Ren Jianing <jianing.ren@rock-chips.com>
Signed-off-by: Ren Jianing <jianing.ren@rock-chips.com>
Co-developed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
New Rockchip devices have the usb phy nodes as standalone devices.
These nodes have register nodes with #address_cells = 2, but only
use 32 bit addresses.
Adjust the driver to check if the returned address is "0", and adjust
the index in that case.
Derived and adjusted the similar change from linux-next with below
commit <9c19c531dc98> ("phy: phy-rockchip-inno-usb2: support
#address_cells = 2")
Co-developed-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa Compute Module 3(CM3) IO board an application board from Radxa
and is compatible with Raspberry Pi CM4 IO form factor.
Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.
Add support for Radxa CM3 IO Board defconfig and -u-boot.dtsi
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Radxa Compute Module 3(CM3) IO board an application board from Radxa
and is compatible with Raspberry Pi CM4 IO form factor.
Specification:
- 1x HDMI,
- 2x MIPI DSI
- 2x MIPI CSI2
- 1x eDP
- 1x PCIe card
- 2x SATA
- 2x USB 2.0 Host
- 1x USB 3.0
- 1x USB 2.0 OTG
- Phone jack
- microSD slot
- 40-pin GPIO expansion header
- 12V DC
Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.
linux-next commit for the same,
commit <8f19828844f2> ("arm64: dts: rockchip: Fix compatible for Radxa
CM3")
Add support for Radxa CM3 IO Board.
Co-developed-by: FUKAUMI Naoki <naoki@radxa.com>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Co-developed-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa Compute Module 3(CM3) is one of the modules from a series
System On Module based on the Radxa ROCK 3 series and is compatible
with Raspberry Pi CM4 pinout and form factor.
Specification:
- Rockchip RK3566
- up to 8GB LPDDR4
- up to 128GB high performance eMMC
- Optional wireless LAN, 2.4GHz and 5.0GHz IEEE 802.11b/g/n/ac wireless,
BT 5.0, BLE with onboard and external antenna.
- Gigabit Ethernet PHY
Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.
Since Radxa CM3 is compatible with Raspberry Pi CM4 pinout so it is
possible to mount Radxa CM3 on top of the Rasberry Pi CM4 IO board.
linux-next commit for the same,
commit <8f19828844f2> ("arm64: dts: rockchip: Fix compatible for Radxa
CM3")
Add support for Radxa CM3.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Co-developed-by: FUKAUMI Naoki <naoki@radxa.com>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Sync rockchip,vop2.h from linux-next, and the last commit is
commit <604be85547ce> ("drm/rockchip: Add VOP2 driver")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Like other rockchip SoCs, DM_RESET is useful across rk3568
platform.
Select it from arch kconfig.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The board should be RV1126-NEU2 instead RV1126-ECM0.
Fix the wrong name.
Fixes: b8f1ca9540 ("board: rockchip: Add Edgeble Neu2 IO Board")
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add default memory addresses for kernel_comp_addr_r and kernel_comp_size
to enable booting from a compressed kernel image. This area is temporarily
used to decompress the kernel image on-the-fly.
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add Radxa ROCK 3 Model A support. sync rk3308-rock-pi-s.dts from
Linux 6.2.0-rc7.
ROCK Pi S is RK3308 based SBC from radxa.com. ROCK Pi S has a,
- 256MB/512MB DDR3 RAM
- SD, NAND flash (optional on board 1/2/4/8Gb)
- 100MB ethernet, PoE (optional)
- Onboard 802.11 b/g/n wifi + Bluetooth 4.0 Module
- USB2.0 Type-A HOST x1
- USB3.0 Type-C OTG x1
- 26-pin expansion header
- USB Type-C DC 5V Power Supply
Linux commit commit for the same,
<2e04c25b1320> ("arm64: dts: rockchip: add ROCK Pi S DTS support")
Signed-off-by: Akash Gajjar <gajjar04akash@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add Radxa ROCK 3 Model A support. sync rk3568-rock-3a.dts from Linux 6.2.0-rc7
Board Specifications
- Rockchip RK3568
- 2/4/8GB LPDDR4 3200MT/s
- eMMC socket, SD card slot
- GbE LAN
- PCIe 3.0/2.0
- M.2 Connector
- 3.5mm Audio jack with mic
- HDMI 2.0, MIPI DSI/CSI
- USB 3.0 Host/OTG, USB 2.0 Host
- 40-pin GPIO expansion ports
- USB Type C PD 2.0, 9V/2A, 12V/2A, 15V/2A, 20V/2A
Refer Linux commit <22a442e6586c>
("arm64: dts: rockchip: add basic dts for the radxa rock3 model a")
Signed-off-by: Akash Gajjar <gajjar04akash@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Using the mkimage entry with the multiple-data-files prop and having a
missing external blob result in an unexpected ValueError exception using
the --allow-missing flag.
ValueError: Filename 'missing.bin' not found in input path (...)
Fix this by using _pathname that is resolved by ObtainContents for blob
entries, ObtainContents also handles allow missing for external blobs.
Mark mkimage entry as missing and return without running mkimage when
missing entries is reported by CheckMissing.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The current init size limit of 76KiB is too big to fit in the 64KiB SRAM
on RK3568, sync init size limit from vendor u-boot to fix this.
Set init size limit to 60KiB (-16KiB) for RK3568.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Latest vendor TPL for RK3328 has grown past the current init size limit
of 28KiB, sync the init size limit from vendor u-boot to fix this.
Set init size limit to 30KiB (+2KiB) for RK3328.
This makes it possible to use latest vendor TPL on RK3328 without
getting a size limit error running the mkimage command.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
An external TPL binary is now expected to be provided using ROCKCHIP_TPL
when building RK3568 targets.
This reverts commit 31500e7bcf.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip SoCs typically use U-Boot TPL to initialize DRAM, then jumps
back to BootRom to load next stage, U-Boot SPL, into DRAM. BootRom then
jumps to U-Boot SPL to continue the normal boot flow.
However, there is no support to initialize DRAM on RK35xx SoCs using
U-Boot TPL and instead an external TPL binary must be used to generate a
bootable u-boot-rockchip.bin image.
Add CONFIG_ROCKCHIP_EXTERNAL_TPL to indicate that an external TPL should
be used. Build U-Boot with ROCKCHIP_TPL=/path/to/ddr.bin to generate a
bootable u-boot-rockchip.bin image for RK3568.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Eugen Hristev <eugen.hristev@collabora.com>
The rockchip-tpl entry can be used when an external TPL binary should be
used instead of the normal U-Boot TPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Eugen Hristev <eugen.hristev@collabora.com>
The rk3328 sdram driver read sdram parameters from the devicetree into a
struct rk3328_sdram_params using dev_read_u32_array.
After commit 5ab30c3176 ("ram: rockchip: Update ddr pctl regs for px30")
changed the size of struct ddr_pctl_regs, a member of struct
rk3328_sdram_params, U-Boot TPL can no longer initialize DRAM on RK3328.
Add ten u32 to the sdram parameter array in devicetree to align with
this size change. This fixes DRAM initialization on RK3328.
Fixes: 5ab30c3176 ("ram: rockchip: Update ddr pctl regs for px30")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # roc-rk3328-cc
Add a second dram bank of usable memory beyond the blob of space for
peripheral near 4GB. Any memory that exists beyond the 4GB mark is added
to the second bank.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Newer DRAM initialization blobs from vendor can encode sdram info in a
new version 3 format. The new format makes use of more bits in sys_reg3
compared to the version 2 format.
Add basic support for detecting the version 3 format and decoding the
high bits used for ddrtype.
This fixes decode of sdram size on my RK3568 boards that have LPDDR4X.
Details on the new format was deciphered from vendor u-boot commit [1].
[1] c69667e0e2
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CONFIG_RAM_PX30_DDR4 got renamed to CONFIG_RAM_ROCKCHIP_DDR4 in commit
26f92be07e ("ram: rockchip: Add common ddr type configs"). Since both
patchsets were merged unbeknownst to the other, the conflict wasn't
detected while testing each patchset individually and could only be
observed after a merge to master branch.
Fixes: c925be73a0 ("rockchip: add support for PX30 Ringneck SoM on Haikou Devkit")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The RK3288 TRM states that, for 8-bit DDR modes:
The CLKDIV register should always be programmed with a value
higher than zero (0); that is, a clock divider should always be
used for 8-bit DDR mode.
In Linux, the driver applies this logic for all SoCs using the driver
and does not distinguish RK3288, so presumably this requirement is the
same for all other Rockchip SoCs using this IP.
Add the necessary code to double the clock frequency when 8-bit DDR is
selected. The dw_mmc core already handles setting CLKDIV correctly
given the input clock and desired bus clock.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Provide human-readable manufacturer and product names for the
FriendlyELEC NanoPi R4S.
Enable CONFIG_SYSINFO and CONFIG_SYSINFO_SMBIOS by default.
Signed-off-by: Christian Kohlschütter <christian@kohlschutter.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The PMC_MCK1 clock id for the ebi node is 23.
Fixes: 746b738224 ("ARM: dts: at91: sama7g5/sama7g5ek: align with Linux DT")
Reviewed-by: Eugen Hristev <eugen.hristev@collabora.com>
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
