Add support for detection of SR2.0 version of DRA72x family of
processors.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Same flash driver can be used by other stm32 families like stm32f7.
Better place for this driver would be mtd driver location.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
The direct write config register is needed for SPI direct write mode
configuration.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Stefan Roese <sr@denx.de>
cpu_eth_init is no longer called for dm enabled eth drivers, this
was causing the sunxi gmac eth controller to no longer work in u-boot.
This commit fixes this by calling the clock, reset and pinmux setup
function from s_init() and enabling the phy power pin (if any) from
board_init().
The enabling of phy power cannot be done from s_init because it uses dm
and dm is not ready yet at this point.
Note that the mdelay is dropped as the phy gets enabled much earlier
now, so it is no longer needed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Tested-by: Karsten Merker <merker@debian.org>
Tested-by: Michael Haas <haas@computerlinguist.org>
On the A83T and H3, the SID block is at a different address.
Furthurmore, the e-fuses are at an offset of 0x200 within the
hardware's address space.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
During initial DDR training, false parity errors may be detected.
This patch adds workaround to fix the erratum.
Tested on LS2085QDS and LS2080RDB.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The per-PCI controller LUT (Look-Up-Table) is a 32-entry table
that maps PCI requester IDs (bus/dev/fun) to a stream ID.
Add defines for the register offsets.
Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Update comments around how stream IDs are partitioned.
Stream IDs allocated to PCI are no longer divided up by
controller, but are instead a contiguous range
Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As the compatible property values for QSPI and DSPI dts nodes
are changed in kernel, FSL_QSPI_COMPAT and FSL_DSPI_COMPAT
need to be updated too.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
To use AQR405 PHY's interrupt, we need to invert the relative IRQ pins
polarity by setting IRQCR register, because AQR405 interrupt is low
active but GIC accepts high active.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Enable wuo config to accelerate coherent ordered writes for LS2080A
and LS2085A.
WRIOP IP is connected to RNI-20 Node.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
If EMIF is idle for certain amount of DDR cycles, EMIF will put the
DDR in self refresh mode to save power if EMIF_PWR_MGMT_CTRL register
is programmed. And also before entering suspend-resume ddr needs to
be put in self-refresh. Linux kernel does not program this register
before entering suspend and relies on u-boot setting.
So configuring it in u-boot.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
By now the code to only have a single page table level with 64k page
size and 42 bit address space is no longer used by any board in tree,
so we can safely remove it.
To clean up code, move the layerscape mmu code to the new defines,
removing redundant field definitions.
Signed-off-by: Alexander Graf <agraf@suse.de>
The MMU range table can vary depending on things we may only find
out at runtime. While the very simple ThunderX variant does not
change, other boards will, so move the definition from a static
entry in a header file to the board file.
Signed-off-by: Alexander Graf <agraf@suse.de>
The idea to generate our pages tables from an array of memory ranges
is very sound. However, instead of hard coding the code to create up
to 2 levels of 64k granule page tables, we really should just create
normal 4k page tables that allow us to set caching attributes on 2M
or 4k level later on.
So this patch moves the full_va mapping code to 4k page size and
makes it fully flexible to dynamically create as many levels as
necessary for a map (including dynamic 1G/2M pages). It also adds
support to dynamically split a large map into smaller ones when
some code wants to set dcache attributes.
With all this in place, there is very little reason to create your
own page tables in board specific files.
Signed-off-by: Alexander Graf <agraf@suse.de>
When running in EL1, AArch64 knows two page table maps. One with addresses
that start with all zeros (TTBR0) and one with addresses that start with all
ones (TTBR1).
In U-Boot we don't care about the high up maps, so just disable them to ensure
we don't walk an invalid page table by accident.
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Based on the memory map we can determine a lot of hard coded fields of
TCR, like the maximum VA and max PA we want to support. Calculate those
dynamically to reduce the chance for pit falls.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reboot mode is written to SAR memory before reboot in the form of a string.
This mechanism is supported on OMAP4 by various TI kernels.
It is up to each board to make use of this mechanism or not.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This correctly enables the USB PHY clocks, by enabling CM_ALWON_USBPHY_CLKCTRL
and correctly setting CM_L3INIT_USBPHY_CLKCTRL's value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
There is no distinction between essential and non-essential mux configuration,
so it doesn't make sense to have an "essential" prefix.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Individual boards might provide their own emif_get_device_timings function and
use the jedec timings in their own way, hence those have to be exported.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Individual boards might provide their own emif_get_device_timings function and
use the elpidia timings in their own way, hence those have to be exported.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Individual boards might provide their own emif_get_device_details function and
use elpidia device details in their own way, hence those have to be exported.
This also wraps existing definitions with the proper ifdef logic.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This introduces a define for the offset to the reboot reason, rather than
hardcoding it.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This switches reboot mode handling to a string-based interface, that allows more
flexibility to set a common interface with the next generations of OMAP devices.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
Given that DRA7/OMAP5 SoCs can support more than 2GB of memory,
enable interleaving for this higher memory to increase performance.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Read and write leveling can be enabled independently. Check for these
enable bits before updating the read and write leveling output values.
This will allow to use the combination of software and hardware leveling.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Many TI EVMs have capability to store relevant board information
such as DDR description in EEPROM. Further many pad configuration
variations can occur as part of revision changes in the platform.
In-order to support these at runtime, we for a board detection hook
which is available for override from board files that may desire to do
so.
NOTE: All TI EVMs are capable of detecting board information based on
early clocks that are configured. However, in case of additional needs
this can be achieved within the override logic from within the board
file.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Several TI EVMs have EEPROM that can contain board description information
such as revision, DDR definition, serial number, etc. In just about all
cases, these EEPROM are on the I2C bus and provides us the opportunity
to centralize the generic operations involved.
The on-board EEPROM on the BeagleBone Black, BeagleBone, AM335x EVM,
AM43x GP EVM, AM57xx-evm, BeagleBoard-X15 share the same format.
However, DRA-7* EVMs, OMAP4SDP use a modified format.
We hence introduce logic which is generic between these platforms
without enforcing any specific format. This allows the boards to use the
relevant format for operations that they might choose.
This module will compile for all TI SoC based boards when
CONFIG_TI_I2C_BOARD_DETECT is enabled to have optimal build times for
platforms that require this support.
It is important to note that this logic is fundamental to the board
configuration process such as DDR configuration which is needed in
SPL, hence cannot be part of the standard u-boot driver model (which
is available later in the process). Hence, to aid efficiency, the
eeprom contents are copied over to SRAM scratchpad memory area at the
first invocation to retrieve data.
To prevent churn with cases such as DRA7, where eeprom format maybe
incompatible, we introduce a generic common format in eeprom which
is made available over accessor functions for usage.
Special handling for BBG1 EEPROM had to be introduced thanks to the
weird eeprom rev contents used.
The follow on patches introduce the use of this library for AM335x,
AM437x, and AM57xx.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Centralize gpi2c_init into omap_common from the sys_proto header so
that the information can be reused across SoCs.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Early clock initialization is currently done in two stages for OMAP4/5
SoCs. The first stage is the initialization of console clocks and
then we initialize basic clocks for functionality necessary for SoC
initialization and basic board functionality.
By splitting up prcm_init and centralizing this clock initialization,
we setup the code for follow on patches that can do board specific
initialization such as board detection which will depend on these
basic clocks.
As part of this change, since the early clock initialization
is centralized, we no longer need to expose the console clock
initialization.
NOTE: we change the sequence slightly by initializing console clocks
timer after the io settings are complete, but this is not expected
to have any functioanlity impact since we setup the basic IO drive
strength initialization as part of do_io_settings.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.
Move these options to Kconfig and tidy up board configuration:
CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA
Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.
Note: Masahiro's moveconfig.py script is amazing.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>
LVDS have a different display out mode, add code to get right flag.
The vop_ip decide display device and the remote_vop_id decide which
vop was being used. So we should use the remote_vop_id to set DCLK_VOP.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Acked-by: Simon Glass <sjg@chromium.org>
Some Rockchip SoCs support LVDS output. Add a display driver for this so
that these displays can be used on supported boards.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Acked-by: Simon Glass <sjg@chromium.org>
Kconfig options must defined in the defconfig files. Since RSA_SOFTWARE_EXP
relies on CONFIG_DM, unless it is set in kconfig we cannot enable RSA.
Remove the hacks which enable CONFIG_DM in header files and update the
defconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
During very early boot-ROM execution the pinmux
configuration isi in Hi-Z state. If pull-up is enabled
on GPIO pad's there will be a short period of toggle
from high to low on the IO when GPIO is set low during
boot. To avoid this glitch, disable pull-up configuration
in GPIO pinmux.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
I implemented a GPIO driver based on Driver Model for the UniPhier
SoC family, but I could not find any good reason why such SoC
specific GPIO headers are needed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Base addresses for GPIOs could be different for different socs, this
patch moves the base addresses from driver to the soc specific location.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
This patch removes the gpio clock enable from gpio driver & move it in the
board code, making it possible to use the gpio driver with other socs.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
The initialization for smmu and stream id is moved into the common soc
code.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Memory controller performance is not optimal with default internal
target queue register value, write required value for optimal DDR
performance.
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support for phy 1-3.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: use setclrbits_le32 instead of read-modify-write]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Remove unused macros. Adresses are taken from DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
