The TWL6030 power driver is only built when CONFIG_TWL6030_POWER is selected,
thus there is no reason to wrap the code with ifdef.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
When booting from USB, the bootrom sets the VUSB_IN_PMID bit of the MISC2
register of the TWL6030. However, U-Boot sets the VUSB_IN_VSYS bit to enable
VBUS input. As both bits are contradictory, enabling both disables the input,
according to the TWL6030 TRM.
Thus, we need to clear the VUSB_IN_PMID bit in case of an USB boot (which could
just as well be a memory boot after USB timed out).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Not every device has multiple MMC slots available, so it makes sense to enable
only the required LDOs for the available slots. Generic code in omap_hsmmc will
enable both VMMC and VAUX1, in doubt.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This enables the VAUX1 supply, used for eMMC power in standard configurations.
Its voltage is determined by the value of the BOOT2 pin of the TWL6030.
Note that the TWL6030 might already have enabled this regulator at startup
(depending on the value of the BOOT3 pin of the TWL6030), according to the
TWL6030 datasheet.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This makes the twl6030 mmc and usb-related power registers and values
definitions more explicit and clear and adds prefixes to them.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Add the following functions:
tps65218_reg_read() for accessing redisters
tps65218_toggle_fseal() for toggling the fseal bit
tps65218_lock_fsea() for locking the fseal bit to 1
Add the following defines:
All status register bits
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
SY8106A is a PMIC which is used on the Allwinner
H3 Orange Pi Pc and Plus board. The VOUT1_SEL register is
implemented to set the default V-CPU voltage to 1200 mV.
This driver is required to ensure the SY8106A V-CPU
voltage is set to 1200 mV after a software reset. On cold
boot the default SY8106A output voltage is selected to be
1200 mV by a pair of resistors on the Orange Pi PC and Plus.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Previously, AXP818 ALDO support was partially added to Kconfig, but
never enabled in the board file, nor properly set or configured in
Kconfig. The boards continue to work because the AXP818 is designed
to pair with the A83T/H8, and the default voltages match the reference
design's requirements.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
AXP818 provides an array of LDOs to provide power to various peripherals.
None of these regulators are critical.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Instead of one function for each DLDO regulator, make 1 function that
takes an extra "index". Since the control bits for the DLDO regulators
are contiguous, this makes the function very simple. This removes a lot
of duplicate code.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Adds poweroff support for axp209 pmic.
Signed-off-by: Michael van Slingerland <michael@deviousops.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Some regulators will not implement any operations (e.g. fixed regulators).
This is not an error, so allow the autoset process to continue when one
of these regulators is found.
Signed-off-by: Simon Glass <sjg@chromium.org>
The currect PMIC debugging is a little confusing. Adjust it so that it is
clear whether the operation succeeded or failed. Also, avoid creating a new
error return value when a perfectly good one is already available.
Signed-off-by: Simon Glass <sjg@chromium.org>
For some boards the pmic interface is useful but the regulator interface
(which comes with it) is too large. Allow them to be separated such that
SPL can decide which it needs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add regulator support for the RK808 PMIC. It integrated 4 BUCKs and 8 LDOs
all of which are supported by this driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
This Rockchip PMIC provides features suitable for battery-powered
applications. It is commonly used with Rockchip SoCs.
Add a driver which provides register access. The regulator driver will use
this.
Signed-off-by: Simon Glass <sjg@chromium.org>
With gcc-5.3 we get a warning for using switch() on a bool type.
Rewrite these sections as if/else and update the one section that was
using 1/0 instead of true/false.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
AXP818 is rsb based PMIC and used on Allwinner A83T H8 Homlet dev board.
It's registers are different and calculating reg config is different than
that of earlier axp power ICs.
DCDC1, DCDC2, DCDC3 and DCDC5 is implemented at the moment.
all other voltages can be added subsequently.
AXP datasheet is uploaded to wiki:
http://linux-sunxi.org/File:AXP818_datasheet_Revision1.0.pdf
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add initial sun8i H3 support, only uart + mmc are supported for now.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The console includes a global variable and several functions that are only
used by a small subset of U-Boot files. Before adding more functions, move
the definitions into their own header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some devices are supplied by configurable regulator's output.
But there was no function for getting it. This commit adds
function, that allows for getting the supply device by it's phandle.
The returned regulator device can be used with regulator uclass's API.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This driver allows I/O operations on the Samsung S2MPS11 PMIC,
which provides lots of LDO/BUCK outputs.
To enable it, update defconfig with:
- CONFIG_PMIC_S2MPS11
and additional, if were not defined:
- CONFIG_CMD_PMIC
- CONFIG_ERRNO_STR
The binding info: doc/device-tree-bindings/pmic/s2mps11.txt
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
LDO3 and LDO4 are normally either unused, or used to power csi
attached camera sensors, and as such do not need to be enabled at
boot time.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for disabling the regulators found on the axp209 pmic.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The only thing axp221.c's axp_init() does which needs protection
against multiple calls is calling pmic_bus_init, and pmic_bus_init()
itself is already protected against being called multiple times.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Use the generic pmic_bus helpers for the axp152 / axp209 drivers,
rather then having them define their own register read / write
functions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
On A23 / A33 boards aldo1 is used for VCC-IO and should be 3.0V, make this
the default.
Note that this does not cause any functional changes since all sun8i
board defconfig-s already contained: CONFIG_AXP_ALDO1_VOLT=3000 .
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Change the axp223 dcdc2 / VDD-SYS default from 1.2V to 1.1V, 1.1V is the
value recommended by Allwinner and is what most fex files specify.
This has been tested on a number of A23/A33 tablets including on an
A23 Ippo-q8h-v1.2 PCB tablet which has a fex file which specifies 1.2V
(which is where our original 1.2V default comes from).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Stop prefixing the axp functions for setting voltages, etc. with the
model number, there ever is only one pmic driver built into u-boot,
this allows simplifying the callers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
On boards with axp221/223 pmic-s we already allow configuring most
voltages. Make the Kconfig options for these also apply to boards with
axp152 / axp209 pmic-s and extend them to configure all voltages.
The Kconfig defaults are chosen so that this commit does not introduce any
functional changes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Kconfig-ify CONFIG_AXP152_POWER and _AXP209_POWER settings, removing
them from CONFIG_SYS_EXTRA_OPTIONS.
Note that sun5i boards can have either an AXP209 or an AXP152 pmic, the
Kconfig default is AXP209, boards with an AXP152 must explicitly select
this. Likewise boards without a pmic must explicitly select SUNXI_NO_PMIC
in their defconfig.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add a full regulator driver for the ACT8846. This provides easy access to
voltage and current settings for each regulator.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a driver for the ACT8846 PMIC. This supports several LDOs and BUCKs and
is connected to the I2C bus. This driver supports using a regulator driver
to access the regulators.
Signed-off-by: Simon Glass <sjg@chromium.org>
* Add pmic pfuze3000 support, implement power_pfuze3000_init to be
used in power_init_board callback function.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Allow specifying the axp221 dcdc2 voltage via Kconfig, this is necessary
because on some boards the 1.2V default does not work reliable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We have flipped CONFIG_SPL_DISABLE_OF_CONTROL. We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:
#ifdef CONFIG_OF_CONTROL
# if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
# define OF_CONTROL 0
# else
# define OF_CONTROL 1
# endif
#else
# define OF_CONTROL 0
#endif
Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute. It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.
Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This part of mentioned commit, was missed by my mistake during the rebase.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Original commit message:
power: pmic: pfuze100 support driver model
1. Support driver model for pfuze100.
2. Introduce a new Kconfig entry DM_PMIC_PFUZE100 for pfuze100
3. This driver intends to support PF100, PF200 and PF3000, so add
the device id into the udevice_id array.
4. Rename PMIC_NUM_OF_REGS macro to PFUZE100_NUM_OF_REGS.
Change-Id: I4fc88414f3c0285f9648e47ec7aed60addeccc4d
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a simple pmic driver for the hi6553 pmic which is used in
conjunction with the hi6220 SoC on the hikey board. Eventually this
driver will be updated to be a proper UCLASS PMIC driver which
can parse the voltages direct from device tree.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
This adds support for powering off (the omap3 SoC) from the twl4030. This is
especially useful when the kernel does not actually power off the device using
this method but reboots and leaves it up to the bootloader to actually turn the
power off.
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
The return type of pmic_read and pmic_write is signed int, so
correct variable 'ret' from type unsigned int to int.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
1. Add new regulator driver pfuze100.
* Introduce struct pfuze100_regulator_desc for maintaining info
for one regulator.
2. Add new Kconfig entry DM_REGULATOR_PFUZE100 for pfuze100.
3. This driver intends to support PF100, PF200 and PF3000.
4. Add related macro definition in pfuze header file.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
1. Support driver model for pfuze100.
2. Introduce a new Kconfig entry DM_PMIC_PFUZE100 for pfuze100
3. This driver intends to support PF100, PF200 and PF3000, so add
the device id into the udevice_id array.
4. Rename PMIC_NUM_OF_REGS macro to PFUZE100_NUM_OF_REGS.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
If there is no property named 'regulator-name' for regulators,
choose node name instead, but not directly return failure value.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Remove the old drivers (both the normal one and the cros_ec one) now that
we have new drivers that use driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Not all regulators can be set up automatically. Adjust the code so that
regulators_enable_boot_on() will return success when some are skipped.
Only genuine errors are reported.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Some regulators use the wrong voltage register and thus it is not possible
to control them. Fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
This should write the register, not read it. Fix this bug.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
The driver name should not have a space in it. Also the regulator names
should match the case of the device tree. Fix these problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
This PMIC is used with SoCs which need a combination of BUCKs and LDOs. The
driver supports changing voltage and enabling/disabling each regulator. It
supports the standard device tree binding and supports driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
This PMIC is used with SoCs which need a combination of BUCKs and LDOs. The
driver supports probing and basic register access. It supports the standard
device tree binding and supports driver model. A regulator driver can be
provided also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
The TPS65090 has 7 FETs which are modelled as regulators. This allows them
to be controlled by drivers easier, accessed through the 'regulator' command
and used by other drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
The existing TPS65090 driver does not support driver model. Add a new one
that does. This can be used as a base for a regulator driver also. It uses
the standard device tree binding.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
The Chrome OS EC supports tunnelling through to an I2C bus on the EC. This
currently uses a copy of the I2C command code and a special 'crosec'
sub-command.
With driver model we can define an I2C bus which tunnels through to the EC,
and use the normal 'i2c' command to access it. This simplifies the code and
removes some duplication.
Add an I2C driver which tunnels through to the EC. Adjust the EC code to
support binding child devices so that it can be set up. Adjust the existing
I2C xfer function to fit driver model better.
For now the old code remains to allow things to still work. It will be
removed in a later patch once the new flow is fully enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the common function to obtain the number from the end of the string,
instead of a local function. Also tweak the position of a debug() statement.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
It is a common requirement to update some PMIC registers. Provide some
simple convenience functions to do this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
To reduce unnecessary code size in an uncommon code path, use debug()
where possible(). The driver returns an error which indicates failure.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
The device tree provides information about which regulators should be
on at boot, or always on. Use this to set them up automatically.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
The regulator_autoset() function mixes printf() output and PMIC adjustment
code. It provides a boolean to control the output. It is better to avoid
missing logic and output, and this permits a smaller SPL code size. So
split the output into a separate function.
Also rename the function to have a by_name() suffix, since we would like
to be able to pass a device when we know it, and thus avoid the name
search.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Decide when the regulator is set up whether we want to auto-set the voltage
or current. This avoids the complex logic spilling into the processing code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
This is not user input (i.e. from the command line). It should be possible
to get the case correct and avoid the case-insensitive match. This will
help avoid sloppy device tree setups.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
This commit adds emulation of sandbox PMIC device, which includes:
- PMIC I2C emulation driver
- PMIC I/O driver (UCLASS_PMIC)
- PMIC regulator driver (UCLASS_REGULATOR)
The sandbox PMIC has 12 significant registers and 4 as padding to 16 bytes,
which allows using 'i2c md' command with the default count (16).
The sandbox PMIC provides regulators:
- 2x BUCK
- 2x LDO
Each, with adjustable output:
- Enable state
- Voltage
- Current limit (LDO1/BUCK1 only)
- Operation mode (different for BUCK and LDO)
Each attribute has it's own register, beside the enable state, which depends
on operation mode.
The header file: sandbox_pmic.h includes PMIC's default register values,
which are set on i2c pmic emul driver's probe() method.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested on sandbox:
Tested-by: Simon Glass <sjg@chromium.org>
This cleanup includes:
- remove of the preprocessor macros which pointed to long name functions
- update of the names of some regulator uclass driver functions
- cleanup of the function regulator_autoset()
- reword of some comments of regulator uclass header file
- regulator_get_by_platname: check error for uclass_find_* function calls
- add function: regulator_name_is_unique
- regulator post_bind(): check regulator name uniqueness
- fix mistakes in: regulator/Kconfig
- regulator.h: update comments
- odroid u3: cleanup the regulator calls
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested on sandbox:
Tested-by: Simon Glass <sjg@chromium.org>
The cleanup includes:
- pmic.h - fix mistakes in a few comments
- pmic operations: value 'reg_count' - redefine as function call
- fix function name: pmic_bind_childs() -> pmic_bind_children()
- pmic_bind_children: change the 'while' loop with the 'for'
- add implementation of pmic_reg_count() method
- pmic_bind_children() - update function call name
- Kconfig: add new line at the end of file
- Update MAX77686 driver code
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested on sandbox:
Tested-by: Simon Glass <sjg@chromium.org>
This driver implements regulator operations for fixed Voltage/Current
value regulators. beside the standard regulator constraints, which are
put into the uclass platform data, a typical fixed regulator node provides
few additional properties like:
- gpio
- gpio-open-drain
- enable-active-high
- startup-delay-us
The only 'gpio' is used by this driver and is kept in structure of type
'fixed_regulator_platdata', as a device platform data (dev->platdata).
The driver implements:
- get_value
- get_current
- get_enable
- set_enable
The regulator calls and commands can be used for fixed-regulator devices,
and the proper error will be returned for prohibited.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds support to MAX77686 regulator driver,
based on a driver model regulator's API. It implements
almost all regulator operations, beside those for setting
and geting the Current value.
For proper bind and operation it requires the MAX77686 PMIC driver.
New file: drivers/power/regulator/max77686.c
New config: CONFIG_DM_REGULATOR_MAX77686
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
This is the implementation of driver model PMIC driver.
The max77686 PMIC driver implements read/write operations and driver
bind method - to bind its childs.
This driver will try to bind the regulator devices by using it's child
info array with regulator prefixes and driver names. This should succeed
when compatible regulator driver is compiled. If no regulator driver found,
then the pmic can still provide read/write operations, and can be used with
PMIC function calls.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit introduces the implementation of dm regulator API.
Device tree support allows for auto binding. And by the basic
uclass operations, it allows to driving the devices in a common
way. For detailed informations, please look into the header file.
Core files:
- drivers/power/regulator-uclass.c - provides regulator common functions api
- include/power/regulator.h - define all structures required by the regulator
Changes:
- new uclass-id: UCLASS_REGULATOR
- new config: CONFIG_DM_REGULATOR
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit introduces the PMIC uclass implementation.
It allows providing the basic I/O interface for PMIC devices.
For the multi-function PMIC devices, this can be used as I/O
parent device, for each IC's interface. Then, each PMIC particular
function can be provided by the child device's operations, and the
child devices will use its parent for read/write by the common API.
Core files:
- 'include/power/pmic.h'
- 'drivers/power/pmic/pmic-uclass.c'
The old pmic framework is still kept and is independent.
For more detailed informations, please look into the header file.
Changes:
- new uclass-id: UCLASS_PMIC
- new config: CONFIG_DM_PMIC
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
With the full PMIC framework we may be able to avoid this. But for now
we need access to the PMIC.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Move the axp-gpio code out of the drivers/power/axp*.c code, and into
a new separate axpi-gpio driver.
This change drops supports for the gpio3 pin on the axp209, as that requires
special handling, and no boards are using it.
Besides cleaning things up by moving the code to a separate driver, as
a bonus this change also adds support for the (non vusb) gpio pins on the
axp221 and the gpio pins on the axp152.
The new axp-gpio driver gets its own Kconfig option, and is only enabled
on boards which need it. Besides that it only gets enabled in the regular
u-boot build and not for the SPL as we never need it in the SPL.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Move the register helpers used to access the registers via p2wi resp.
rsb bus on the otherwise identical axp221 and axp223 pmics to a separate
file, so that they can be used by the upcoming standalone axp gpio driver
too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Change the axp_gpio_foo function prototypes to match the gpio uclass op
prototypes, this is a preparation patch for moving the axp gpio code to
a separate driver-model gpio driver.
Note that the ugly calls with a NULL udev pointer in drivers/gpio/sunxi_gpio.c
this adds are removed in a later patch.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
vbus-usable may not get set if power is provided through both the power barrel
connector and external 5v is also present on the otg connector, at least on
boards where vbus is also controlled through the axp221-pmic.
One way to reproduce this is to bootup an Ippo-q8h board with a usb-host
cable plugged into the otg (so that it will get powered), then unplug the
usb-host cable and plug in a charger, and then do "reset" on the u-boot
console, vbus-usable will then report 0, leading to uboot trying to provide
power to the otg port even though external 5v is present, this commit fixes
this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This converts the VBUS detection and enable logic to GPIO instead of separate
axp functions and checks that have to be used aside usual GPIO functions.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
board/sunxi/board.c tries to set ldo3 to 2.8v however drivers/power/axp209.c
contains an incorrect limit on ldo3 of 2.275v
The origin of the incorrect limit seems likely due to some inconsistencies
in the axp209 datasheet. ldo3 is described with different limits in
different sections. register 0x29 uses 7 bits for voltage configuration
while the 2.275v limit would apply if only 6 bits were used.
Probably this is a cut&paste error from register 0x23
The linux kernel driver has the correct limit and operation up to the 2.8v
required by my board has been physically verified with a multimeter.
Signed-off-by: Iain Paton <ipaton0@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Some of the AXP PMICs support VBUS detection, i.e. checking whether
VBUS power input is available and usable (supplied by an external
source). A few boards use this instead of a separate GPIO to detect
VBUS on USB OTG.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
It turns out that the device_mode_data is rsb specific, rather then slave
specific, so integrate the rsb_set_device_mode() call into rsb_init().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Rather than assuming that the chip offset length is 1, allow it to be
provided. This allows chips that don't use the default offset length to
be used (at present they are only supported by the command line 'i2c'
command which sets the offset length explicitly).
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Add a dm_ prefix to driver model I2C functions so that we can keep the old
ones around.
This is a little unfortunate, but on reflection it is too difficult to
change the API. We can undo this rename when most boards and drivers are
converted to use driver model for I2C.
Signed-off-by: Simon Glass <sjg@chromium.org>
And also add Kconfig option for selecting ELDO3 voltage. The reason
for having this option is that the Android kernel sets ELDO3 to
1.2V when powering up LCD in the case if 'lcd_if' configuration
variable is set to 6 (LCD_IF_EXT_DSI) in the FEX file. Most likely
to supply power for a SSD2828 chip.
However on the MSI Primo81 tablet, which is using this particular
'lcd_if = 6' setup for LCD, setting the ELDO3 voltage appears to
be unnecessary and it works regardless. Having no schematics of
this tablet, I can only guess that 1.2V is supplied to SSD2828
in some other way.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
We do not use the axp209 interrupt, and at least in my mini-x (which does not
have a power button) the pwr-button pin and the irq pin are soldered together,
so if the axp209 keeps it irq asserted too long it will see a 10s pwr-button
press and hard power off the board, disabling the irqs fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The axp221 / axp223's N_VBUSEN pin can be configured as an output rather
then an input, add axp_drivebus_enable() and _disable() functions to set
the pin in output mode and control it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The voltage setting code knows it needs to call axp221_init before calling
the various voltage setting functions.
But users of axp utility functions like axp221_get_sid() do not know this,
so the utility functions always call axp221_init() to ensure that the
p2wi / rsb setup magic has been done.
Since doing this repeatedly is quite expensive, add a check to axp221_init
so that it only does the initialization once.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
ALDO2 is used to power LPDDR2 SDRAM on both the reference design and the
Hummingbird A31, when this type of RAM is present.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Some boards use GPIO-s on the pmic, one example of this is the A13-OLinuXino
board, which uses gpio0 of the axp209 for the lcd-power signal.
This commit adds support for gpio pins on the AXP209 pmic, the sunxi_gpio.c
changes are universal, adding gpio support for the other AXP pmics (when
necessary) should be a matter of adding the necessary axp_gpio_foo functions
to their resp. drivers, and add "#define AXP_GPIO" to their header file.
Note this commit only adds support for the non device-model version of the
gpio code, patches for adding support to the device-model version are very
welcome.
The string representation for these gpio-s is AXP0-#, the 0 in the AXP0 prefix
is there in case we need to support gpio-s on more then 1 pmic in the future.
At least A80 boards have 2 pmics, and we may end up needing to support gpio-s
on both.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Explicitly turn off unused voltages, rather then leaving them as is. Likewise
explictly enabled the dcdc convertors, rather then assuming they are already
enabled at boot.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The dcdc1 voltage is typically used as generic 3.3V IO voltage for things like
GPIO-s, sdcard interfaces, etc. On most boards this is undervolted to 3.0V to
safe battery, but not on all, make it configurable so that we can use the
same settings as the original firmware on all boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Some of the ldo-s of the axp221 are used in the same way on most boards, add
comments to the Kconfig help text to reflect this, and give them defaults
matching their typical usage.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The axp223 appears to be the same as the axp221, except that it uses the
rsb to communicate rather then the p2wi. At least all the registers we use
are 100% the same.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
For sun6i the SID is stored in the pmic, rather then in the SoC itself,
add a function to retreive the sid.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This regulator is used with AM437x IDK to feed
VDD_MPU, without means to scale VDD_MPU we can't
support higher frequencies.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The AS3722 provides a number of DC/DC converters and LDOs as well as 8
GPIOs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This converts all Tegra boards over to use driver model for I2C. The driver
is adjusted to use driver model and the following obsolete CONFIGs are
removed:
- CONFIG_SYS_I2C_INIT_BOARD
- CONFIG_I2C_MULTI_BUS
- CONFIG_SYS_MAX_I2C_BUS
- CONFIG_SYS_I2C_SPEED
- CONFIG_SYS_I2C
This has been tested on:
- trimslice (no I2C)
- beaver
- Jetson-TK1
It has not been tested on Tegra 114 as I don't have that board.
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Not every device has multiple MMC slots available, so it makes sense to enable
only the required LDOs for the available slots. Generic code in omap_hsmmc will
enable both VMMC1 and VMMC2, in doubt.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
just add a few ifdefs around because this
device is very similar to dra7xxx.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Allow to set the buck voltage for the max77686.
This will be used to reset the SMC LAN9730 ethernet on the odroids.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The A31 uses the AXP221 pmic for various voltages.
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
--
Changes in v2:
-Rebase
Changes in v3:
-Add support for all dldo and aldo-s
-Add Kconfig option to select building AXP221 and to select voltage of
dldo and aldo-s
Changes in v4:
-Add axp221_setbits helper function
-Use symbolic names for enabled bits in CTRL1 - CTRL3 registers
The pmic_spi_free function isn't ever used, and as the frameworks stand
today, cannot be, so remove it. Integrate the probe function into
pmic_reg as it's not really a "probe" today. Finally, add an err label
for the common failure cases.
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This enables the VMMC2 LDO, which powers the MMC2 device.
When the device starts from MMC2, this has already been enabled by the BootROM,
but when starting from peripheral boot (USB, UART), it is not the case.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Currently uboot wrongly uses 25mV / step for dcdc3, this is a copy and paste
error introduced when adding the axp152_mvolt_to_target during review of the
axp152.c driver. This results in u-boot setting Vddr to 2.3V instead of 1.5V.
This commit fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Exynos 5250 boards (snow, spring) use the I2C driver but Exynos 5420 boards
cannot due to a hardware design decision. Select the correct driver to use
in each case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Unfortunately on Pit the AP has no direct access to the tps65090 but must
talk through the EC (over SPI) to the EC's I2C bus.
When driver model supports PMICs this will be relatively easy. In the
meantime the best approach is to duplicate the driver. It will be refactored
once driver model support is expanded.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This would be useful to start moving various config options.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
It is redundant to use 'PFUZE100_PMIC' as the PMIC name because we already
know it is a PMIC.
Call it simply 'PFUZE100' instead.
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Add in an init function for the drivers/power framework so we can dump
and read the registers via i2c.
Cc: Łukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
Add support for the x-powers axp152 pmic which is found on most A10s boards
and enable it for the r7-tv-dongle board.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for the x-powers axp209 pmic which is found on most A10, A13 and
A20 boards.
And enable AXP209 support for the Cubietruck and Cubieboard boards.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Since p->bus is unsigned checking for negative values
is optimized away. Since bus is already used as an argument
use tmp. While at it, don't declare variables in the middle
of a function.
cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The function tps65090_init checks the i2c bus of p->bus. However
the pointer p is not intialiased at this point. Check the local
variable bus instead.
cc: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Simon Glass <sjg@chromium.org>
The current pmic i2c code assumes the current i2c bus is
the same as the pmic device's bus. There is nothing ensuring
that to be true. Therefore, select the proper bus before performing
a transaction.
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This adds driver support for the TPS65090 PMU. Support includes
hooking into the pmic infrastructure so that the pmic commands
can be used on the console. The TPS65090 supports the following
functionality:
- fet enable/disable/querying
- getting and setting of charge state
Even though it is connected to the pmic infrastructure it does
not hook into the pmic charging charging infrastructure.
The device tree binding is from Linux, but only a small subset of
functionality is supported.
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Signed-off-by: Katie Roberts-Hoffman <katierh@chromium.org>
Signed-off-by: Rong Chang <rongchang@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This enum should be common across all PMICs rather than having it
independently defined with the same name in multiple places.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Commit be3b51aa did this mostly, but several have been added since. Do the
job again.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Conflicts:
boards.cfg
Conflicts were trivial once u-boot-arm/master boards.cfg was
reformatted (commit 6130c146) to match u-boot/master's own
reformatting (commit 1b37fa83).
The LTC3676 PMIC includes four DC/DC converters, and three 300mA
LDO Regulators (two Adjustable). The DC/DC converters are adjustable based
on a resistor devider (board-specific).
This adds support for the LTC3676 by creating a namespace unique init function
that uses the PMIC API to allocate a pmic and defines the registers.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Avoid uding pmic_init() as this forces the model of only allowing a
single PMIC driver to be built at a time.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Lack of this check resulted in a data abort when CPU tried to execute the
following command (without further mandatory input): 'pmic MAX77686_PMIC'.
Only the 'pmic list' command requires one passed parameter.
Other require at least two valid parameters for correct operation.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Remove wrong and unused env variables
Trats2 is not as GT-I8800.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Issues:
- reading i2c data by passing u16 pointer causes errors in read data.
- max17042 status register fields have not only Power On Reset meaning
so using proper mask is required.
Changes:
- read i2c data to type u32 instead of u16 - avoids buffer overflow
- compare FG status register using mask not just one bit value
- add checking return value to functions fg read/write
- add model lock and model check count
- add debug msg
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Added chip type detection and twl6032
support in the battery control
and charge functions.
Based on Balaji T K <balajitk@ti.com> patches for TI u-boot.
Signed-off-by: Oleg Kosheliev <oleg.kosheliev@ti.com>
The data struct is used to support different
PMIC chip types. It contains the chip type and
the data (e.g. registers addresses, adc multiplier)
which is different for twl6030 and twl6032.
Replaced some hardcoded values with the
structure vars.
Based on Balaji T K <balajitk@ti.com> patches for TI u-boot.
Signed-off-by: Oleg Kosheliev <oleg.kosheliev@ti.com>
There is no need to pass p->bus differently when the PMIC is connected via SPI
or via I2C.
Handle the both cases in the same way.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Add new functionality to turn on SMPS10 regulator.
This supplies the VBUS to devices connected to the
USB host ports
Signed-off-by: Dan Murphy <dmurphy@ti.com>
This patch prevents data abort when pmic bat command is called
on non-batery pmic device.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Lukasz Majewski <l.majewski@samsung.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch add support for new multi function pmic max77693.
The driver is split into three modules: pmic, muic and fuelgage.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add a driver for the TPS65910 PMIC that is found in the AM335x GP EVM,
AM335x EVM SK and others.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
[trini: Split and rework Avinash's changes into new drivers/power
framework]
Signed-off-by: Tom Rini <trini@ti.com>
Add a driver for the TPS65217 PMIC that is found in the Beaglebone
family of boards.
Signed-off-by: Greg Guyotte <gguyotte@ti.com>
[trini: Split and rework Greg's changes into new drivers/power
framework]
Signed-off-by: Tom Rini <trini@ti.com>
This patch add new functions to pmic max77686 to set voltage and mode.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
After introduction of unified i2c model, the I2C_SET_BUS() macro is regarded
as obsolete.
Hence it is replaced with i2c_set_bus_num() function call.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Add support for disabling battery charging with ctrl+C keyboard
combination pressed.
Moreover the battery update is done more frequently.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch implements the mux_addr bit fields defined in tmu_control
register (used for debugging purpose)
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Vadim Bendebury <vbendeb@google.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch does the folowing
1. change the data types for unsigned int variable to unsigned
2. change the tmu_base type to struct exynos5_tmu_reg *
3. Add timer functionality for get_cur_temp()
4. error handling in the get_tmu_fdt_values()
5. Add check for curr_temp reading
6. some cosmotic changes.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Vadim Bendebury <vbendeb@google.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add some useful functions, and the corresponding definitions.
Add support for powering on the dra7xx_evm SD/MMC LDO
(courtesy Lokesh Vutla <lokeshvutla@ti.com>).
Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
Reviewed-by: Tom Rini <trini@ti.com>
commit 21144298 (power: twl6035: add palmas PMIC support)
introduced twl6035_i2c_[read|write]_u8
Then, commit dd23e59d (omap5: pbias ldo9 turn on)
introduced palmas_[read|write]_u8 for precisely the same access
function. TWL6035 belongs to the palmas family, so instead of having
an twl6035 API, we could use an generic palmas API instead.
To stay consistent with the function naming of twl4030,6030 accessors,
we use palmas_i2c_[read|write]_u8
Cc: Balaji T K <balajitk@ti.com>
Cc: Sricharan R <r.sricharan@ti.com>
Reported-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Since TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs,
rename twl6035_mmc1_poweron_ldo by a more generic palmas_mmc1_poweron_ldo
function.
Signed-off-by: Nishanth Menon <nm@ti.com>
Since TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs,
rename twl6035_init_settings with an more generic palmas_init_settings
Signed-off-by: Nishanth Menon <nm@ti.com>
TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs
Rename twl6035 to palmas to allow reuse across multiple current and
future platforms
As part of this change, change the CONFIG_TWL6035_POWER to
CONFIG_PALMAS_POWER and update usage of header file accordingly.
Signed-off-by: Nishanth Menon <nm@ti.com>
twl6030_i2c_[read|write]_u8 can be used else where to access
multi-function device such as twl6030, so move the register access
functions to the common twl6030.h header file.
Signed-off-by: Nishanth Menon <nm@ti.com>
u-boot standard i2c read prototype is
i2c_read(addr, reg, 1, &buf, 1)
twl4030_i2c_read_u8(u8 addr, u8 *val, u8 reg)
does not provide consistency, so switch the prototype to be
consistent with rest of u-boot i2c operations:
twl4030_i2c_read_u8(u8 addr, u8 reg, u8 *val)
Signed-off-by: Nishanth Menon <nm@ti.com>
u-boot standard i2c register write prototype is
i2c_reg_write(u8 addr, u8 reg, u8 val)
twl4030_i2c_write_u8(u8 addr, u8 val, u8 reg)
does not provide consistency, so switch the prototype to be
consistent with rest of u-boot i2c operations:
twl4030_i2c_write_u8(u8 addr, u8 reg, u8 val)
Signed-off-by: Nishanth Menon <nm@ti.com>
This adds hardware tripping at 110 degrees celsius which must enable
forced system shutdown in case TMU fails to power off.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Adding Exynos Thermal Management Unit driver to monitor SOC
temperature and take actions corresponding to states of TMU.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Moved the pmic_max77686.c max77686_pmic.h to drivers/power
and made required changes accordingly
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
We handle i2c_write return code and complain in case of error. We propagate the
error, too, to allow better handling at the upper level in the future.
Signed-off-by: Vincent Stehlé <v-stehle@ti.com>
Two extra commands:
"pmic name bat state" and "pmic name bat charge" has been added to
pmic framework. Those provides state display and charge capabilities
to named batteries.
The pmic_core.c file has been refactored to more consistent name scheme.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Function for calculating LDO internal register value from passed micro
Volt.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Support for MAX17042 fuel-gauge (FG), which is built into the MAX8997
power management device.
Special file - fg_battery_cell_params.h with cells characteristics
added.
The FG device will work with redesigned PMIC framework.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Support for MUIC (Micro USB Integrated Circuit) built into the MAX8997
power management device.
The MUIC device will work with redesigned PMIC framework.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Trats battery is now treated in the same way as other power related
devices. This approach allows for more unified handling of all devices
responsible for power management.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
The PMIC framework has been moved to its more natural place
./drivers/power from ./drivers/misc directory.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This power management chip supports battery charging and a large number
of power supplies. This initial driver only provides the ability to adjust
the two synchronous buck converters SM0 and SM1 in a stepwise manner.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
twl4030_pmrecv_vsel_cfg currently first sets up device group (effectively
enabling the supply), and only then sets vsel (selects voltage). This could
lead to wrong voltage for a short time, or even long time if second i2c
write fails.
Fix this by writing vsel first and device group after that. Also
introduce error checking to not enable the supply if we failed to set
the voltage, and start logging errors as power supply problems are
usually important.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
MMC interfaces are specified to be 3.3V compatible with an operating
voltage range of 3.1V to 3.5V for SD cards. This change affects
hardware using TWL4030 (TPS6595x) PMICs and should improve the
reliability when communicating with marginally-spec'd MMC devices.
3.15V is the highest possible level for this chip. This patch
has been tested on a Gumstix Overo board.
Signed-off-by: Ash Charles <ash@gumstix.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
Config VMMC voltage to 3V for MMC/SD card slot
and PBIAS settings needed for OMAP4
Fixes MMC/SD detection on boot from eMMC.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
1. ftpmu010.h: fix and add definitions
Enhanced for more features and asm related support
according to datasheet.
Note:
- FTPMU010_PDLLCR0_HCLKOUTDIS is "incorrect" in datasheet.
- FTPMU010_PDLLCR0_DLLFRANG is only 1 bit at bit #19. (not 20-19)
- FTPMU010_PDLLCR0_HCLKOUTDIS is 4 bits at bit #20. (not 24-21)
2. ftpmu010.c: enhance features and fix relocation
- The following functions is added for pmu features.
ftpmu010_mfpsr_select_dev()
ftpmu010_sdramhtc_set()
- This patch also fix the declare statement for relocation.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Faraday's ftpmu010 is a power managemnet unit which support cpu
sleep and frequency scaling. It has been integrated into many SoC.
This patch also move ftpmu010 to a proper place for later enhancement.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Add battery charging support twl6030 driver.
Add support for battery voltage and current measurements.
Add command to get battery status and start/stop battery charging from USB.
Signed-off-by: Balaji T K <balajitk@ti.com>
Tested-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
This patch adds a function to allow one to easily set the target
voltage for the TWL4030 regulators. It also modifies the existing
code to use this new function. Applicable definitions are moved
out of the driver file and into the header file so that they are
generally accessible
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch add the basic infrastructure for the TWL6030 driver and enables
support in the two existing OMAP4 boards, Panda and OMAP4430 SDP
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Because twl4030 now has its own device files, move and rename
twl4030_mmc_config.
twl4030_mmc_config initializes the twl4030 power setting to
the mmc device. Because it is in the twl4030 power domain, move
it out of drivers/mmc/omap3_mmc.c and into drivers/power/twl4030.c.
The function was renamed to twl4030_power_mmc_init because all
the functions in this file are to have the format
twl4030_power_<device>_<action>
In this case the suffix is mmc_init so
device : mmc
action : init
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
Because twl4030 now has its own device files, move exiting
omap3 power_init_r to a new location.
power_init_r is the only function in board/omap3/common.
It initializes the twl4030 power for the board and enables
the led.
The power part of the the function is moved to twl4030_power_init in
drivers/power/twl4030.c The power compilation is conditional on the
existing config variable CONFIG_TWL4030_POWER.
The led part is moved to twl4030_led_init in the new file
drivers/misc/twl4030_led.c The led compilation is conditional on
the new config variable CONFIG_TWL4030_LED
The directory board/omap3/common was removed because power_init_r
was the only function in it.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
The Zoom2 power reset button is on the top right side of the
main board. Press and hold for about to 8 seconds to completely
reset the board.
Some of the beta boards have a hardware problem that prevents
using this feature. If is difficult to further characterize the
boards that fail. So disable resetting for all beta boards.
The Zoom1 reset button is the red circle on the top right,
front of the board. Press and hold the button for 8 seconds to
completely reset the board.
After analyzing beagle, it was determined that other boards
that use the twl4030 for power managment can also make use
this function.
The resetting is done by the power management part of the twl4030.
Since there is no existing drivers/power, add one.
The compilation of power/twl4030.h is controlled by the config
variable CONFIG_TWL4030_POWER
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
