legacy_hole_base_k and legacy_hole_size_k are defined but
not used.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With bootstage we need access to the timer before driver model is set up.
To handle this, put the required state in global_data and provide a new
function to set up the device, separate from the driver's probe() method.
This will be used by the 'early' timer also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This adds support to Intel Cherry Hill board, a board based on
Intel Braswell SoC. The following devices are validated:
- serial port as the serial console
- on-board Realtek 8169 ethernet controller
- SATA AHCI controller
- EMMC/SDHC controller
- USB 3.0 xHCI controller
- PCIe x1 slot with a graphics card
- ICH SPI controller with an 8MB Macronix SPI flash
- Integrated graphics device as the video console
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
FSP's built-in UPD configuration enables PUNIT power configuration,
but on B0 stepping, this causes CPU hangs in fsp_init(). Disable it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds microcode device tree fragment for Braswell B0 (406C2),
C0 (406C3) and D0 (406C4) stepping SoC.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds initial Intel Braswell SoC support. It uses Intel FSP
to initialize the chipset.
Similar to its predecessor BayTrail, there are some work to do to
enable the legacy UART integrated in the Braswell SoC.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
FSP spec 1.1 adds 3 new APIs and their offsets are in the header.
Update the 'fsp hdr' command to show these new entries.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a VBT is given to an FSP that supports graphics initialization,
the FSP will produce a graphics info HOB that contains all necessary
information for the linear frame buffer of the integrated graphics
device. This adds a DM video driver for it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that binman is able to recognize the Video BIOS Table entry,
add such one in the u-boot.dtsi.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds Kconfig options for Video BIOS Table which is normally
required if you are using an Intel FSP firmware that is complaint
with spec 1.1 or later to initialize the integrated graphics device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a new HOB type for graphics information introduced in FSP
spec 1.1. When graphics capability is included in FSP and enabled,
FSP produces an FSP_GRAPHICS_INFO_HOB as described in the EFI PI
specification which provides information about the graphics mode and
framebuffer.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
FSP spec 1.1 adds one more member to the struct common_buf to
determine the memory size that can be reserved by FSP below "top
of low usable memory" for bootloader usage. This new member uses
the reserved space so that it is still compatible with previous
FSP spec 1.0.
A new HOB (FSP_HOB_RESOURCE_OWNER_BOOTLOADER_TOLUM_GUID) is also
published when common_buf.tolum_size is valid and non zero.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Import include/linux/dma-direction.h from Linux 4.13-rc7 and delete
duplicated definitions of enum dma_data_direction.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
It was noticed a few times, that the reboot from Linux (reboot command)
is different from the reboot (reset command) under U-Boot. The U-Boot
version does seem to reset the board more deeply (PCI cards etc) than
the Linux reboot.
This is actually caused by missing full reset bit in the reset register
value in the ACPI FADT table.
Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
These options should not be exposed to other platforms.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Some Intel FSP (like Braswell) does SPI lock-down during the call
to fsp_notify(INIT_PHASE_BOOT). But before SPI lock-down is done,
it's bootloader's responsibility to configure the SPI controller's
opcode registers properly otherwise SPI controller driver doesn't
know how to communicate with the SPI flash device.
This introduces a Kconfig option CONFIG_FSP_LOCKDOWN_SPI for such
FSPs. When it is on, U-Boot will configure the SPI opcode registers
before the lock-down.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we support multiple environment drivers but there is not way to
select between them at run time. Also settings related to the position and
size of the environment area are global (i.e. apply to all locations).
Until these limitations are removed we cannot really support more than one
environment location. Adjust the location to be a choice so that only one
can be selected. By default the environment is 'nowhere', meaning that the
environment exists only in memory and cannot be saved.
Also expand the help for the 'nowhere' option and move it to the top since
it is the default.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Move all of the imply logic to default X if Y so it works again]
Signed-off-by: Tom Rini <trini@konsulko.com>
When CONFIG_EFI_PARTITION is not set, the following build error is
seen in arch/x86/lib/acpi_s3.c:
error: expected declaration specifiers or '...' before '*' token
static void asmlinkage (*acpi_do_wakeup)(void *vector) = (void*)WAKEUP_BASE;
This is actually caused by missing asmlinkage declaration, but with
CONFIG_EFI_PARTITION on, the declaration comes from part.h which
is included from common.h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Neither new design uses ISA bus, nor does any U-Boot codes use these
codes. Remove them.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
After MMC is converted to DM, convert to use DM SCSI as well for all
x86 boards and imply BLK for both MMC and SCSI drivers.
CONFIG_SCSI_DEV_LIST is no longer used. Clean them up.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert the pci_mmc driver over to driver model and migrate all x86 boards
that use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: remove DM_MMC from edison_defconfig]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
The value of uma_memory_size depends on an undefined value
from the stack. The value of uma_memory_size is changed but
never used.
So simply remove this superfluous code.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts Intel ICH6 GPIO driver to Kconfig, and add it to the
imply list of platform drivers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Like other peripheral drivers, move USB related drivers to platform
Kconfig as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Imply Tangier-specific drivers in the platform Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
U-Boot as coreboot payload can run on any x86 hardware ideally.
Let's imply some common drivers that are useful.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Imply drivers that are working with Ivybridge platform in the
platform Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
BayTrail integrates lots of peripherals that have U-Boot drivers.
Imply those in the platform Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Platform knows whether MRC cache is implemented, but using it can
be a choice of a specific board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is architecture-dependent early initialization hence should
be put in the platform Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
arch_misc_init() is intended to do architecture-dependent stuff.
This is required by each platform.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_BOARD_EARLY_INIT_F literally indicates board-specific codes
and should be not 'default y' for all x86 boards.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Intel Management Engine is required by the platform, however it's
not a must have when building a U-Boot image. For example, during
development normally programming ME firmware is a one-time effort.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some firmwares might have another window for generated tables.
So, introduce two configuration options to select start address and
maximum length for the generated tables.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
64-bit U-Boot image is a combination of 32-bit U-Boot (SPL) plus
64-bit U-Boot (proper). For the U-Boot proper, it has be compiled
to 64-bit object codes. Attempting to use a toolchain to compile
64-bit U-Boot for qemu-x86_64, like kernel.org 4.9 i386-linux-gcc,
fails with the following errors:
arch/x86/cpu/intel_common/microcode.c:79:2: error: PIC register
clobbered by 'ebx' in 'asm'
The issue is because toolchain is preconfigured to generate code
for the 32-bit architecture (i386), and currently '-m64' is missing
in the makefile fragment. Using kernel.org 4.9 x86_64-linux-gcc
works out of the box, since it is preconfigured to generate 64-bit
codes.
When compiling U-Boot SPL, '-m32' is passed to the toolchain, no
mater 32-bit (i386-linux-) or 64-bit (x86_64-linux) the toolchain
is preconfigured to generate.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present U-Boot x86 build is using -mpreferred-stack-boundary=2
which is 4 bytes stack boundary alignment. With 64-bit U-Boot, the
minimal required stack boundary alignment is 16 bytes.
If -mpreferred-stack-boundary is not specified, the default is 4
(16 bytes). Switch to use the default one.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present the AHCI SCSI driver only supports PCI with driver model.
Rename the existing function to indicate this and add support for adding
a non-PCI controller .
Signed-off-by: Simon Glass <sjg@chromium.org>
If ACPI HW reduced bit in FADT is set we should ignore any ACPI hardware
communications.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some platforms might require different approach when filling memory
mappings configuration table.
Allow them to override the common method.
At the same time export acpi_create_mcfg_mmconfig().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In Baytrail and Quark support code acpi_fill_madt() is identical.
Deduplicate its implementation by moving to lib/acpi_tables.c.
At the same time mark acpi_fill_madt() with __weak attribute to keep a
possibility to override it in platform code
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
ACPI specification defines FADT fields marked as reserved in U-Boot.
Name these fields in accordance with ACPI specification.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
