The current transfer code relies on ctrlc() to abort transfers, but this
requires user interactivity. Naturalize the process with a timeout.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch re-formats the arm920t s3c24x0 driver files, excluding the nand
driver, in preparation for changes to add support for the Embest SBC2440-II Board.
The changes are as follows:
- re-indent the code using Lindent
- make sure register layouts are defined using a C struct
- replace the upper-case typedef'ed C struct names with lower case
non-typedef'ed ones
- make sure registers are accessed using the proper accessor functions
- run checkpatch.pl and fix any error reports
It assumes the following patch has been applied first:
- [U-Boot][PATCH-ARM] CONFIG_SYS_HZ fix for ARM902T S3C24X0 Boards, 05/09/2009
- patches 1/4 and 2/4 of this series
Tested on an Embest SBC2440-II Board with local u-boot patches as I don't have
any s3c2400 or s3c2410 boards but need this patch applying before I can submit
patches for the SBC2440-II Board. Also, temporarily modified sbc2410x, smdk2400,
smdk2410 and trab configs to use the mtd nand driver (which isn't used by any
board at the moment), ran MAKEALL for all ARM9 targets and no new warnings or
errors were found.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
__i2c_read always ends with a STOP condition thereby releasing
the bus. It is cleaner to do the STOP magic in i2c_read(), like
i2c_write() does. This may also help future multimaster systems which
wants to hold on to the bus until all transactions are finished.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
The latest AN2919 has changed the way FDR/DFSR should be calculated.
Update the driver according to spec. However, Condition 2
is not accounted for as it is not clear how to do so.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Some boards need a higher DFSR value than the spec currently
recommends so give these boards the means to define there own.
For completeness, add CONFIG_FSL_I2C_CUSTOM_FDR too.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
After issuing a STOP one must wait until the STOP has completed
on the bus before doing something new to the controller.
Also add an extra read of SR as the manual mentions doing that
is a good idea.
Remove surplus write of CR just before a write, isn't required and
could potentially disturb the I2C bus.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
The value of I2C_TIMEOUT in fsl_i2c.c has several problems. First, it is
defined as CONFIG_HZ/4, but it is used as a count of microseconds, so it makes
no sense to derive it from a clock rate. Second, the current value (250) is
too low for some boards, so it needs to be increased. Third, the timeout
necessary for multiple-master arbitration is larger than the timeout for basic
read/write operations, so we shouldn't have a single constant for both timeouts.
Finally, it would be nice if we could override these values on a per-board
basis.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Tested-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Peter Tyser <ptyser@xes-inc.com>
This problem is seen on Zoom1 and Zoom2 in the startup and
when i2c probe is used
Before :
In: serial
Out: serial
Err: serial
timed out in wait_for_bb: I2C_STAT=1000
timed out in wait_for_bb: I2C_STAT=1000
timed out in wait_for_bb: I2C_STAT=1000
timed out in wait_for_pin: I2C_STAT=1000
I2C read: I/O error
timed out in wait_for_bb: I2C_STAT=1000
timed out in wait_for_bb: I2C_STAT=1000
Die ID #327c00020000000004013ddd05026013
Hit any key to stop autoboot: 0
OMAP3 Zoom1# i2c probe
Valid chip addresses:timed out in wait_for_bb: I2C_STAT=1000
02 03 04 05 06 07 08 09 0A 0B 0C 0D <snip>
After :
In: serial
Out: serial
Err: serial
Die ID #327c00020000000004013ddd05026013
Hit any key to stop autoboot: 0
OMAP3 Zoom1# i2c probe
Valid chip addresses: 48 49 4A 4B
The addresses are for the twl4030.
The prescalar that converts the function clock to the sampling
clock is hardcoded to 0. The reference manual recommends 7
if the function clock is 96MHz.
Instead of just changing the hardcoded values, the prescalar
is calculated from the value I2C_IP_CLK.
The i2c #defines are in kHz. The speed passed into the
i2c init routine is in Hz. To be consistent, change the
defines to be in Hz.
The timing calculations are based on what is done in the
linux 2.6.30 kernel in drivers/i2c/buses/i2c_omap.c as
apposed to what is done in TRM.
The major variables in the timing caculations are
specified as #defines that can be overriden as required.
The variables and their defaults are
I2C_IP_CLK SYSTEM_CLOCK_96
I2C_INTERNAL_SAMPLING_CLK 19200000
I2C_FASTSPEED_SCLL_TRIM 6
I2C_FASTSPEED_SCLH_TRIM 6
I2C_HIGHSPEED_PHASE_ONE_SCLL_TRIM I2C_FASTSPEED_SCLL_TRIM
I2C_HIGHSPEED_PHASE_ONE_SCLH_TRIM I2C_FASTSPEED_SCLH_TRIM
I2C_HIGHSPEED_PHASE_TWO_SCLL_TRIM I2C_FASTSPEED_SCLL_TRIM
I2C_HIGHSPEED_PHASE_TWO_SCLH I2C_FASTSPEED_SCLH_TRIM
This was runtime verified on Zoom1, Zoom2, Beagle and Overo.
The 400kHz and 3.4M cases were verifed on test Zoom1,
Zoom2, Beagle and Overo configurations.
Testing for omap2 will be done in a second step as Nishanth
and Jean-Christophe commented.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
This patch adds the possibility to call a board specific
i2c bus reset routine for the fsl_i2c bus driver, and adds
this option for the keymile kmeter1 board.
The deblock sequence for this board is implemented and
tested in the following way:
CR = 0x20 (release SDA and SCL pin)
CR = 0xa0 (start read)
dummy read
dummy read
if 2. dummy read == 0x00
3. dummy read
CR = 0x80 (SDA and SCL now 1 SR = 0x86)
CR = 0x00 (Modul reset SR=0x81)
CR = 0x80 (SDA and SCL = 1, SR = 0x81)
Signed-off-by: Heiko Schocher <hs@denx.de>
If doing a pure write with register address and data (not a read/write
combo transfer), we don't set the initial transfer length properly which
ends up causing only the register address to be transferred.
While we're here, fix the i2c_write() parameter description of the buffer.
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The individual i2c commands imd, imm, inm, imw, icrc32, iprobe, iloop,
and isdram are no longer available so all references to them have been
updated to the new form of "i2c <cmd>".
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
New default, weak i2c_get_bus_speed() and i2c_set_bus_speed() functions
replace a number of architecture-specific implementations.
Also, providing default functions will allow all boards to enable
CONFIG_I2C_CMD_TREE. This was previously not possible since the
tree-form of the i2c command provides the ability to display and modify
the i2c bus speed which requires i2c_[set|get]_bus_speed() to be
present.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Add the i2c_init() function so that the tsi108_i2c.c driver fits
U-Boot's standard I2C API which is utilized by cmd_i2c.c
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
This patch fix the compiler/linker errors
common/cmd_i2c.c:1252: undefined reference to `i2c_get_bus_speed'
common/cmd_i2c.c:1256: undefined reference to `i2c_set_bus_speed'
if board use CONFIG_I2C_CMD_TREE and CONFIG_I2C_MULTI_BUS is not
uesd/undef (wrong define order)
and
removes additional empty lines
Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
This patch adds support for the kmsupx4 board from Keymile,
based on a Freescale MPC852T CPU
- serial console on SMC1
- 32 MB SDRAM
- 32 MB NOR Flash
- Ethernet over SCC3
- I2C Bitbang
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch adds I2C mux support for the fsl_i2c driver. This
allows you to add "new" i2c busses, which are reached over
i2c muxes. For more infos, please look in the README and
search for CONFIG_I2C_MUX.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
i.MX31 powers on with most clocks running, so, after a power on this explicit
clock start up is not required. However, as Linux boots it disables most clocks
to save power. This includes the I2C clock. If we then soft reboot from Linux
the I2C clock stays off. This breaks the phycore, which has its environment in
I2C EEPROM. Fix the problem by explicitly starting the clock in I2C driver
initialisation routine.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Ack-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The current Blackfin i2c driver does not work properly with certain devices
due to it breaking up transfers incorrectly. This is a rewrite of the
driver and relocates it to the newer place in the source tree.
Also remove duplicated I2C speed defines in Blackfin board configs and
disable I2C slave address usage since it isn't implemented.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch adds a #define to optionally change the behaviour of
i2c_read() in soft_i2c.c to send an I2C repeated start instead of a
stop-start between sending the device address pointer write and
reading back the data. The current behaviour is retained as the
default.
While most devices will work either way, I have a smart battery(*)
that requires repeated start, and someone at some point found a
device that required a stop-start.
(*) http://www.inspired-energy.com/Standard_Products/NL2054/NL2054%20Rev1.0%20Data%20Sheet.pdf
Signed-off-by: Andrew Dyer <adyer@righthandtech.com>
All implementations of the functions i2c_reg_read() and
i2c_reg_write() are identical. We can save space and simplify the
code by converting these functions into inlines and putting them in
i2c.h.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-By: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
With this Command it is possible to add new I2C Busses,
which are behind 1 .. n I2C Muxes. Details see README.
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch fixes the following warnings, when using
the soft_i2c driver using no CPU pins on MPC82xx or MPC8xx
systems:
soft_i2c.c: In function 'send_reset':
soft_i2c.c:93: warning: unused variable 'immr'
soft_i2c.c: In function 'send_start':
soft_i2c.c:124: warning: unused variable 'immr'
soft_i2c.c: In function 'send_stop':
soft_i2c.c:146: warning: unused variable 'immr'
soft_i2c.c: In function 'send_ack':
soft_i2c.c:171: warning: unused variable 'immr'
soft_i2c.c: In function 'write_byte':
soft_i2c.c:196: warning: unused variable 'immr'
soft_i2c.c: In function 'read_byte':
soft_i2c.c:244: warning: unused variable 'immr'
Signed-off-by: Heiko Schocher <hs@denx.de>
The existing I2C freqency dividers for FDR does not apply
to ColdFire platforms; thus, a seperate table is added
based on MCF5xxx Reference Manual
Signed-off-by: Luigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Acked-by: Tabi Timur <timur@freescale.com>
This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).
Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Add support to the Freescale I2C driver (fsl_i2c.c) for setting and querying
the I2C bus speed. Current 8[356]xx boards define the CFG_I2C_SPEED macro,
but fsl_i2c.c ignores it and uses conservative value when programming the
I2C bus speed.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
