BIST test code has a typo, resulting the binding registers not
maintained as expected. This typo results BIST runs twice on
the covered memory.
Signed-off-by: York Sun <yorksun@freescale.com>
Reported-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Freescale LSCH3 platforms use two DDR controlers interleaving mode out of
reset. It can be configured to disable one controller. To support this
operation, the driver needs to detect and skip the disabled controller.
Signed-off-by: York Sun <yorksun@freescale.com>
Freescale's LS2085A is a another personality of LS2080A SoC with
support of AIOP and DP-DDR.
This Patch adds support of LS2085A Personality.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Updated MAINTAINERS files
Dropped #ifdef in cpu.h
Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: York Sun <yorksun@freescale.com>
SAR1_CPU_CORE_MASK was wrong, probably copy/paste
from another architecture.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
A lot of extra configuration information was left over in the
Marvell serdes and DDR3 initialization code for boards that
U-boot does not support. Remove this extra config information,
and the concept of fixing up board topologies with information
loaded from an EEPROM. If this needs to be done, it should be
handled in the board file, not in core code.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one. This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
SR_IE(Self-refresh interrupt enable) is needed for
Hardware Based Self-Refresh. Make it configurable and let
board code handle the rest.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Reviewed-by: York Sun <yorksun@freescale.com>
introduce BIT() definition, used in at91_udc gadget
driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
[remove all other occurrences of BIT(x) definition]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
Fix the following problem:
drivers/ddr/altera/sequencer.c: In function 'sdram_calibration_full':
drivers/ddr/altera/sequencer.c:1943:25: warning: 'found_failing_read' may be used uninitialized in this function [-Wmaybe-uninitialized]
if (found_passing_read && found_failing_read)
^
drivers/ddr/altera/sequencer.c:1803:26: note: 'found_failing_read' was declared here
u32 found_passing_read, found_failing_read, initial_failing_dtap;
^
Signed-off-by: Marek Vasut <marex@denx.de>
This gem is really really rare, there was an actual float used in
the Altera DDR init code, which pulled in floating point ops from
the libgcc, just wow.
Since we don't support floating point operations the same way Linux
does not support them, replace this with an integer multiplication
and division combo. This removes some 2kiB of size from the SPL as
the floating point ops are no longer pulled in from libgcc.
This was detected by enabling CONFIG_USE_PRIVATE_LIBGCC=y , which
does not contain the floating point bits.
Signed-off-by: Marek Vasut <marex@denx.de>
This patch introduces the SDRAM scrubbing for ECC enabled board
to fill/initialize the ECC bytes. This is done via the XOR engine
to speed up the process. The scrubbing is a 2-stage process:
1) SPL scrubs the area 0 - 0x100.0000 (16MiB) for the main U-Boot
2) U-Boot scrubs the remaining SDRAM area(s)
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This is tested on the DB-MV784MP-GP eval board. To really enable ECC
support on this board the I2C EEPROM needs to get changed. As it
saves the enabling of ECC support internally. For this the following
commands can be used to enable ECC support on this board:
Its recommended for first save (print) the value(s) in this EEPROM
address:
=> i2c md 4e 0.1 2
0000: 05 00 ..
To enable ECC support you need to set bit 1 in the 2nd byte:
Marvell>> i2c mw 4e 1.1 02
Marvell>> i2c md 4e 0.1 2
0000: 05 02 ..
To disable ECC support again, please use this command:
Marvell>> i2c mw 4e 1.1 00
Marvell>> i2c md 4e 0.1 2
0000: 05 00 ..
On other AXP boards, simply plugging an ECC DIMM should be enough to
enable ECC support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Fix most of the dangling checkpatch issues, no functional change.
There are still 7 warnings, 1 checks , but those are left in place
for the sake of readability of the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Actually convert the sequencer code to use socfpga_sdram_misc_config
instead of the various macros. This is just an sed exercise here, no
manual coding needed.
This patch actually removes the need to include any board-specific
files in sequencer.c , so sequencer.c namespace is now no longer
poluted by QTS-generated macros.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
This is another macro used to obfuscate the real code. The
T(INIT|RESET)_CNTR._VAL is always defined, so this indirection
is unnecessary. Get rid of this.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Just use READ_VALID_FIFO_SIZE directly, no need for this macro obfuscation.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce structure socfpga_sdram_misc_config to wrap the remaining
misc configuration values in board file. Again, introduce a function,
socfpga_get_sdram_misc_config(), which returns this the structure. This
is almost the final step toward wrapping the nasty QTS generated macros
in board files and reducing the pollution of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Actually convert the sequencer code to use socfpga_sdram_io_config
instead of the IO_* macros. This is just an sed excercise here, no
manual coding needed.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce structure socfpga_sdram_io_config to wrap the IO configuration
values in board file. Introduce socfpga_get_sdram_io_config() function,
which returns this the structure. This is another step toward wrapping
the nasty QTS generated macros in board files and reducing the pollution
of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Actually convert the sequencer code to use socfpga_sdram_rw_mgr_config
instead of the RW_MGR_* macros. This is just an sed exercise here, no
manual coding needed.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce structure socfpga_sdram_rw_mgr_config to wrap the RW manager
configuration values in board file. Introduce a complementary function,
socfpga_get_sdram_rwmgr_config(), which returns this the structure.
This is another step toward wrapping the nasty QTS generated macros
in board files and reducing the pollution of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce two wrapper functions, socfpga_get_seq_ac_init() and
socfpga_get_seq_inst_init() to avoid direct inclusion of the
sequencer_auto_ac_init.h and sequencer_auto_inst_init.h QTS
generated files. This reduces namespace pollution again.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
This is defined in the QTS-generated headers, so it must not be
re-defined in sequencer.h .
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
These parameters are not used in the code, zap them and the
macros which are used by them as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Move the files generated by QTS into the board directory, they should not
be part of the driver files at all.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Originally, both sdram_start and sdram_end were 64b values. The
sdram_start had no reason for being so, since our address space
is only 32b, so switching sdram_start to u32 is simple.
The sdram_end is a bit more complex, since it can actually be
set to (1 << 32) if someone really wanted to use an SoCFPGA with
4 GiB of DRAM and fixed the code around a little. But, the code
handling the protection rules internally decrements the sdram_end
variable anyway. Thus, instead of calling the code and passing in
the address of the SDRAM end, pass in the address already decremented
by one. This lets the sdram_end be 32b as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Clean the function up so that it's obvious what it is doing,
fix the formating strings in debug outputs, add kerneldoc.
Make the function return proper errno-compliant return values
and propagate this change throughout sdram.c
Signed-off-by: Marek Vasut <marex@denx.de>
Clean up coding style, mostly clean up comments, add kerneldoc.
Also, zap assignment of the "cs" variable, which is outright
dead code, so just remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Pluck out all of the CONFIG_HPS_SDR_CTRLCFG_* macros. This change
makes sdram.c completely clear of these macros and allows removing
of the ugly include of sdram.h . The namespace is now a much nicer
place!
Signed-off-by: Marek Vasut <marex@denx.de>
Introduce socfpga_sdram_get_config() function implement in a board file,
which returns the socfpga_sdram_config structure. This is the last step
in cleaning up the socfpga_mmr_init_full(), but not the last step which
allows removing the inclusion of sdram.h from drivers/ddr/altera/sdram.c
thus far.
Signed-off-by: Marek Vasut <marex@denx.de>
Rework remaining two register setting functions such that they only
return the final register value. Move the register setting into the
block of register I/O in sdram_mmr_init_full().
Signed-off-by: Marek Vasut <marex@denx.de>
Merge sdr_set_*() functions which are just setting registers among
the sea of register setting in sdram_mmr_init_full(). There is no
need to keep them separate this way, there is nothing special about
them.
Signed-off-by: Marek Vasut <marex@denx.de>
Suck out all the CONFIG_HPS_SDR_CTRLCFG_* from sdram_mmr_init_full()
into the socfpga_sdram_config structure. There is still one ugly
macro left behind, but this will be taken care of in subsequent patch.
Signed-off-by: Marek Vasut <marex@denx.de>
Zap all the ad-hoc readbacks from the registers and other useless
and broken debug output. This is really not useful and is only
confusing.
Signed-off-by: Marek Vasut <marex@denx.de>
Introduce this seemingly massive structure, which holds required values
of all the registers of the SDRAM controller. The idea here is to avoid
including the sdram.h header file, which is full of ad-hoc macros that
polute the global namespace. Once the cleanup of sdram.c would be complete
and all registers would be loaded from this new socfpga_sdram_config, a
board file will only pass this structure into the sdram.c . This will
hide all the horrors generated by QTS in the board directory.
Signed-off-by: Marek Vasut <marex@denx.de>
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Signed-off-by: Marek Vasut <marex@denx.de>
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Signed-off-by: Marek Vasut <marex@denx.de>
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Signed-off-by: Marek Vasut <marex@denx.de>
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Signed-off-by: Marek Vasut <marex@denx.de>
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Signed-off-by: Marek Vasut <marex@denx.de>
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Signed-off-by: Marek Vasut <marex@denx.de>
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Merge set_sdr_dram_timing{1,2,3,4,lowpwr}() into single function
set_sdr_dram_timing() , since there's no point in keeping all this
stuff separate anymore.
Signed-off-by: Marek Vasut <marex@denx.de>
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
The big plan here is to remove all the CONFIG_HPS_SDR_ macros, hide
them in QTS compatibility layer in board implementation and pass only
a small structure into the driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Remove all parameters of this function, since they are only constants
passed in from another function, so make them local. Also, rename the
function to get_errata_rows() as this is closer to what it does.
Signed-off-by: Marek Vasut <marex@denx.de>
This function is implementing the DDR calibration Stage 3 as
described in Altera EMI_RM 2015.05.04 . The main body of this
function is almost identical to Stage 1.3 (DQ/DQS centering)
for all but two flags -- use_read_test and update_fom. Convert
this function to call rw_mgr_mem_calibrate_dq_dqs_centering()
with the correct flags set to trim down the code duplication.
Moreover, reorder the remnants in the function a little and
convert the function to return either 0 or -EIO in case of
success and failure respectively, to match the common return
value convention.
Signed-off-by: Marek Vasut <marex@denx.de>
Clean up coding style, mostly broken multiline formatting strings
in debug output. Also clean up data types and constify where applicable.
Signed-off-by: Marek Vasut <marex@denx.de>
Fix data types and constify where applicable, fix broken multiline
debug strings and fix comments. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Fix the return value of the function to match common convention
where 0 means success and negative means error. Fix the return
values in case of an error to use errno.h codes.
Signed-off-by: Marek Vasut <marex@denx.de>
The read_group and write_group arguments are the same in all
cases when this function is invoked, just merge them into one
rw_group argument. Also, clean up the function argument data
types and constify them.
Signed-off-by: Marek Vasut <marex@denx.de>
The search_stop_check() always resets the bit_chk to a new value,
so bit_chk will never survive between search_left_edge() and
search_right_edge() invocation. There is thus no need to pass
it into these functions, so make bit_chk local to them.
Signed-off-by: Marek Vasut <marex@denx.de>
Factor out center_dq_windows(), which is common code between
stage 2 and stage 3 of the calibration again and cater for
the minor differences.
Signed-off-by: Marek Vasut <marex@denx.de>
Factor out the get_window_mid_index() for finding the best DQ
window centering. This is again code common to two stages, so
pull it out.
Signed-off-by: Marek Vasut <marex@denx.de>
First of all, don't break strings in the debug_cond() calls across
multiple lines. Next, zap a couple of really odd casts in the code.
Finally, make i into a signed variable, so it is possible to avoid
constructs of the form:
for (i = FOO;; i--) { <code>; if (i == 0) break; }.
Signed-off-by: Marek Vasut <marex@denx.de>
Factor out common code from search_left_edge() and search_right_edge()
which checks whether searching for the window edge should stop. The
code is almost identical, so pull it into separate function and cater
for the minor differences.
Signed-off-by: Marek Vasut <marex@denx.de>
Factor out common code from rw_mgr_mem_calibrate_writes_center()
and rw_mgr_mem_calibrate_vfifo_center() for searching for the
left edge of the window. The code is almost identical, so pull
it into separate function and cater for the minor differences.
Signed-off-by: Marek Vasut <marex@denx.de>
Factor out common code from rw_mgr_mem_calibrate_writes_center()
and rw_mgr_mem_calibrate_vfifo_center() for searching for the
right edge of the window. The code is almost identical, so pull
it into separate function and cater for the minor differences.
Signed-off-by: Marek Vasut <marex@denx.de>
Reorder the content of the function a little and fix the comments
so they at least become full sentences. Constify function args.
Fix the return value to match the common convention of 0 meaning
success.
Signed-off-by: Marek Vasut <marex@denx.de>
The C language has signed types, so make use of them. Fix this
obscene loop, which tries to do away with unsigned type, but
just makes the code more cryptic.
Signed-off-by: Marek Vasut <marex@denx.de>
Clean up the debug output handling at the end of the function
and factor out common function call from the condition.
Signed-off-by: Marek Vasut <marex@denx.de>
Implement common sdr_find_phase_delay() function and convert all
places which use such code to this unified function. No functional
change to the code.
Signed-off-by: Marek Vasut <marex@denx.de>
If d != 0 after sdr_working_phase() finishes, the else branch
of the condition has no impact on anything at all, since work_end
was already set independently of the value of "d" . Zap this
useless code.
Signed-off-by: Marek Vasut <marex@denx.de>
Fix data types, constify where applicable, fix comments and debug
strings. In case enough failing reads are detected, just return
right away instead of breaking from the loop. This lets us make
the error handling at the end much simpler.
Signed-off-by: Marek Vasut <marex@denx.de>
Pluck out all this VFIFO value counting, which turns out to be
completely unused. Thus, remove it to simplify the code.
Signed-off-by: Marek Vasut <marex@denx.de>
