Mainline kernel has psgtr driver that's why it is good to add description
to DT files. Some boards are just missing description for USB3 and sata.
zc1751-dc1 and p-a2197 are also missing clock descriptions for input
clocks.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP pinctrl Linux driver has been merged to 5.13-rc1 kernel. Based on it
DT files can be extended by pinctrl configurations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There are several changes which happen in mainline kernel which should get
also to U-Boot. Here is the list of patches from the kernel:
- ARM: zynq: Fix leds subnode name for zc702/zybo-z7
- arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
- arm64: dts: zynqmp: Fix u48 si5382 chip on zcu111
- arm64: dts: zynqmp: Wire up the DisplayPort subsystem
- arm64: dts: zynqmp: Add DisplayPort subsystem
- arm64: dts: zynqmp: Add DPDMA node
- arm64: dts: zynqmp: Enable phy driver for Sata on zcu102/zcu104/zcu106
- arm64: dts: zynqmp: Enable si5341 driver for zcu102/106/111
- arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106
- arm64: dts: zynqmp-zcu100-revC: correct interrupt flags
- arm64: dts: xilinx: align GPIO hog names with dtschema
- arm64: zynqmp: Add Xilinx AES node
- dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA
but also some other changes have been done.
- Using only one compatible string for adxl345 on zturn
- Remove Xilinx internal DP bindings
- Remove USB3.0 serdes configurations
- Remove SATA serdes configuration for zc1232
- Resort nvmem_firmware
- Update nand compatible string
- Aling power-domains property for sd0/1
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
s/xlnx,mio_bank/xlnx,mio-bank/g
DT binding is describing mio-bank not mio_bank that's why fix all DTSes and
also driver itself.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Node name should be <name>@<address> which is not how partitions are
described.
Issue was found by running dtbs_check as:
flash@0: 'partition@qspi-device-tree', 'partition@qspi-fsbl-uboot',
'partition@qspi-linux', 'partition@qspi-rootfs'
do not match any of the regexes: ...
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Sync DP subsystem with the latest state in Xilinx U-Boot repository.
This binding hasn't been approved in mainline Linux but it is much better
than ancient version which this patch removes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Modify dts files to add 'no-1-8-v' property for all the ZynqMP boards.
User can remove this property to enable the UHS mode. This is to keep
the same speed (HS) modes across all the stages of the Linux Boot. Due
to power cycling limitation of some of the ZynqMP boards, some SD cards
don't get power cycled and are failing in Linux.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Most of the legacy "gpio-key,wakeup" boolean property is already
replaced with "wakeup-source". However few occurrences of old property
has popped up again, probably from the remnants in downstream trees.
This patch replaces the legacy properties with the unified
"wakeup-source" property introduced by:
"Input: gpio_keys - switch to using generic device properties"
(sha1: 700a38b27eefc582099fdf69effacfad0ad738a4)
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
s/_/-/ for node names.
It fixes warnings like this:
... Warning (node_name_chars_strict): /cpu_opp_table:
Character '_' not recommended in node name ...
Issues reported by make dtbs W=12
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Label property is adding capability to distiguish chips from each other
when iio framework is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add gpio phy reset via I2C expander TCA6416 on board ZCU102.
A warning call trace is observer in probe when this reset is called
from context that can sleep. Keep this commented until that is
resolved in phylib.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The DP83867 strap control workaround is already present in Linux kernel
mainline binding. All these Xilinx boards require this quirk.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Ethernet phys based on devicetree specification should be using
ethernet-phy@ node name instead of pure phy@.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason not to use the Linux "jedec,spi-nor" binding in U-Boot
dts files. This compatible has been added in sf_probe, let use it.
This patch switches to jedec,spi-nor when spi-flash is used in the DTS
and DTSI files, and removed spi-flash when jedec,spi-nor is already
present.
The x86 dts are switched in a separate commit since it depends on a change
in fdtdec.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Evgeniy Paltsev <paltsev@synopsys.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Patrick Delaunay <Patrick.delaunay@st.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
CONFIG_PCA953X is not needed because of PCA953X is integrated in gpio
subsystem already. That's why also remove CMD_PCA953X which is only for
this driver.
zcu102/zcu104-revC/zcu106/zcu111 contain links to eeprom which stores MAC address.
DM_I2C is not enabled for the whole SoC because it increase size for
mini configurations and there is no I2C symbol present to setup
dependencies.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
If there are more instances of si570 clock-output-names property
should be used for differentiation of clock output.
The patch is adding this optional properties for all zynqmp boards with
si570 chip.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds qspi driver support for all ZynqMP ZCU102
boards.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
dtc is showing some warnings and this change was also done in
the Linux kernel as "Input: gpio-keys - clean up device tree binding
example"
with this fragment in commit message
"Drop #address-cells and #size-cells, which are not required by the
gpio-keys binding documentation, as button sub-nodes are not devices."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This part hasn't been pushed to mainline yet that's why remove it.
The patch can be reverted in future when this is pushed there.
Reported-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Mainline Linux kernel has adopted SPDX header license in a different
format then was used before. This patch is syncing it up.
Also update years in License text and remove Nathalie's email because it
is no longer valid.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove overfetch, ratectrl, include-sg and src-issue dma properties.
Driver is not using them and they are also not documented in the binding
doc.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Kedareswara rao Appana <appanad@xilinx.com>
Enable watchdog in dts for zcu102.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The AMS includes an ADC as well as on-chip sensors that can be used to
sample external voltages and monitor on-die operating conditions, such as
temperature and supply voltage levels.
Signed-off-by: Rajnikant Bhojani <rajnikant.bhojani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added pin control support in device tree for zynqmp.
Signed-off-by: Chirag Parekh <chirag.parekh@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Generic dtsi file can't use the same mac address for all.
U-Boot read mac from eeprom in zcu102 case and for others random mac
address is generated.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Used defines rather than raw values for gpio configurations.
Signed-off-by: Chirag Parekh <chirag.parekh@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Not using board revision is causing confusion about which board is
supported and tested. Mark dts files exactly with board revision which
was tested. When new board revision arives it can be symlink if SW view
is the same. Also add -revX suffix to compatible string because user space
tools are parsing this string and can change behavior depends of board
revision.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-02 09:11:52 +02:00
Renamed from arch/arm/dts/zynqmp-zcu102.dts (Browse further)