Commit graph

5362 commits

Author SHA1 Message Date
Remy Bohmer
d6ee5fa40c Fix order for reading rx-status registers in 32bit mode of DM9000
A last minute cleanup before submitting the DM9000A patch series yesterday introduced
a bug in reading the rx-status registers in 32bit mode only.
This patch repairs this.

Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-06-04 23:49:28 -07:00
Remy Bohmer
98291e2e68 DM9000: Some minor code cleanups
Some lines of the U-boot DM9000x driver are longer than 80 characters, or
need some other minor cleanup.

Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-06-04 23:47:32 -07:00
Remy Bohmer
850ba7555d DM9000: Make driver work properly for DM9000A
The DM9000A network controller does not work with the U-boot DM9000x driver.
Analysis showed that many incoming packets are lost.

The DM9000A Application Notes V1.20 (section 5.6.1) recommend that the poll to
check for a valid rx packet be done on the interrupt status register, not
directly by performing the dummy read and the rx status check as is currently
the case in the u-boot driver.

When the recommended poll is done as suggested the driver starts working
correctly on 10Mbit/HD, but on 100MBit/FD packets come in faster so that there
can be more than 1 package in the fifo at the same time.

The driver must perform the rx-status check in a loop and read and handle all
packages until there is no more left _after_ the interrupt RX flag is set.

This change has been tested with DM9000A, DM9000E, DM9000EP.

Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-06-04 23:47:31 -07:00
Remy Bohmer
fbcb7ece0e DM9000: Improve eth_reset() routine
According to the application notes of the DM9000 v1.22 chapter 5.2 bullet 2, the
reset procedure must be done twice to properly reset the DM9000 by means of software.
This errata is not needed anymore for the DM9000A, but it does not bother it.

This change has been tested with DM9000A, DM9000E, DM9000EP.

Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-06-04 23:47:31 -07:00
Remy Bohmer
acba31847f DM9000: improve eth_send() routine
The eth_send routine of the U-boot DM9000x driver does not match the
DM9000 or DM9000A application notes/programming guides.

This change improves the stability of the DM9000A network controller.

This change has been tested with DM9000A, DM9000E, DM9000EP.

Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-06-04 23:47:31 -07:00
Remy Bohmer
134e266253 DM9000: repair debug logging
It seems that the debugging code of the DM9000x driver in U-boot has not been
compiled for a long time, because it cannot compile...

Also rearranged some loglines to get more useful info while debugging.

Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-06-04 23:47:31 -07:00
Remy Bohmer
a101361bfe DM9000: Add data bus-width auto detection.
The U-boot DM9000x driver contains a compile time bus-width definition for
the databus connected to the network controller.

This compile check makes the code unclear, inflexible and is unneccessary.
It can be asked to the network controller what its bus-width is by reading bits
6 and 7 of the interrupt status register.

The linux kernel already uses a runtime mechanism to determine this bus-width,
so the implementation below looks somewhat like that implementation.

This change has been tested with DM9000A, DM9000E, DM9000EP.

Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-06-04 23:47:31 -07:00
Wolfgang Denk
8155efbd7a Merge branch 'master' of ssh://mercury/home/wd/git/u-boot/master 2008-06-05 01:12:30 +02:00
Stefan Roese
63a0afa0c3 ppc4xx: Fix problem with SDRAM init in bamboo NAND booting port
This patch fixes a problem spotted by Eugene O'Brian (thanks Eugene)
introduced by the commit:

ppc4xx/NAND_SPL: Consolidate 405 and 440 NAND booting code in start.S

With this patch SDRAM will get initialized again and booting from NAND
is working again.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Eugene O'Brien <eugene.obrien@advantechamt.com>
2008-06-04 21:34:12 +02:00
Wolfgang Denk
9ef1cbef1a Socrates: Fix PCI bus frequency report
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
2008-06-03 21:49:32 +02:00
Tor Krill
8ec6e332ea Fix incorrect switch for IF_TYPE in part.c
Use correct field in block_dev_desc_t when writing interface type in
dev_print. Error introduced in 574b3195.

Also added fix from Martin Krause

Signed-off-by: Tor Krill <tor@excito.com>
2008-06-03 21:46:39 +02:00
Andre Schwarz
b64b8a0bd3 Add size #defines for Altera Cyclone-II EP2C8 and EP2C20.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
2008-06-03 21:40:09 +02:00
Peter Tyser
35ef877f0a Additional fix to readline_into_buffer() with CONFIG_CMDLINE_EDITING before relocating
Removed unneeded command line history initialization.  Also, the original
code would access the 'initted' variable before relocation to SDRAM
which resulted in erratic behavior since the bss is not initialized when
executing from flash.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2008-06-03 21:33:27 +02:00
Grant Erickson
22f371b630 PPC4xx: Simplified post_word_{load, store}
This patch simplifies post_word_{load,store} by using the preprocessor
to eliminate redundant, copy-and-pasted code.

Signed-off-by: Grant Erickson <gerickson@nuovations.com>
2008-06-03 21:22:26 +02:00
Vasiliy Leoenenko
9c048b5234 cfi_flash: enable M18 flash chips family support.
Added new command set ID. Buffered write command processing is changed
in order to support M18 flash chips family.

Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Signed-off-by: Vasiliy Leonenko <vasiliy.leonenko@mail.ru>
2008-06-03 21:02:34 +02:00
Vasiliy Leoenenko
93c56f212c cfi_flash: support of long cmd in U-boot.
Some NOR flash chips needs support of commands with length grether than max
value size of uchar. For example all M18 family chips use 0x1ff command in
buffered write mode as value of program loops count.

Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Signed-off-by: Vasiliy Leonenko <vasiliy.leonenko@mail.ru>
2008-06-03 21:01:55 +02:00
Stefan Roese
4d91d1df2f DTT: Issue one-shot command on AD7414 (LM75 code) to read temp
On AD7414 the first value upon bootup is not read correctly.
This is most likely because of the 800ms update time of the
temp register in normal update mode. To get current values
each time we issue the "dtt" command including upon powerup
we switch into one-short mode.

This patch fixes the problem on AD7414 equipped boards (Sequoia,
Canyonlands etc), that temp value printed in the bootup log was
incorrect.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-06-03 21:00:00 +02:00
Matthias Fuchs
de5bfcf7b0 ppc4xx: Cleanup CPCI405 variant's config file
This patch removes some dead code from CPCI405 board's
config files. JFFS2 support is also removed. It's not used and
CPCI4052 does not build anymore without some size reduction.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2008-06-03 20:36:59 +02:00
Kenneth Johansson
2918eb9d42 Remove shell variable UNDEF_SYM.
UNDEF_SYM is a shell variable in the main Makefile used to force the
linker to add all u-boot commands to the final image. It has no use here.

Signed-off-by: Kenneth Johansson <kenneth@southpole.se>
2008-06-03 20:36:18 +02:00
Haavard Skinnemoen
8c66497e06 Add support for environment in SPI flash
This is pretty incomplete...it doesn't handle reading the environment
before relocation, it doesn't support redundant environment, and it
doesn't support embedded environment. But apart from that, it does
seem to work.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-06-03 20:33:11 +02:00
Haavard Skinnemoen
b6368467e6 SPI Flash: Add "sf" command
This adds a new command, "sf" which can be used to manipulate SPI
flash. Currently, initialization, reading, writing and erasing is
supported.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-06-03 20:32:25 +02:00
Haavard Skinnemoen
d25ce7d24c SPI Flash subsystem
This adds a new SPI flash subsystem.

Currently, only AT45 DataFlash in non-power-of-two mode is supported,
but some preliminary support for other flash types is in place as
well.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-06-03 20:31:34 +02:00
Hans-Christian Egtvedt
60445cb5c3 atmel_spi: Driver for the Atmel SPI controller
This adds a driver for the SPI controller found on most AT91 and AVR32
chips, implementing the new SPI API.

Changed in v4:
  - Update to new API
  - Handle zero-length transfers appropriately. The user may send a
    zero-length SPI transfer with SPI_XFER_END set in order to
    deactivate the chip select after a series of transfers with chip
    select active. This is useful e.g. when polling the status
    register of DataFlash.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2008-06-03 20:30:05 +02:00
Haavard Skinnemoen
d255bb0e78 SPI API improvements
This patch gets rid of the spi_chipsel table and adds a handful of new
functions that makes the SPI layer cleaner and more flexible.

Instead of the spi_chipsel table, each board that wants to use SPI
gets to implement three hooks:
  * spi_cs_activate(): Activates the chipselect for a given slave
  * spi_cs_deactivate(): Deactivates the chipselect for a given slave
  * spi_cs_is_valid(): Determines if the given bus/chipselect
    combination can be activated.

Not all drivers may need those extra functions however. If that's the
case, the board code may just leave them out (assuming they know what
the driver needs) or rely on the linker to strip them out (assuming
--gc-sections is being used.)

To set up communication parameters for a given slave, the driver needs
to call spi_setup_slave(). This returns a pointer to an opaque
spi_slave struct which must be passed as a parameter to subsequent SPI
calls. This struct can be freed by calling spi_free_slave(), but most
driver probably don't want to do this.

Before starting one or more SPI transfers, the driver must call
spi_claim_bus() to gain exclusive access to the SPI bus and initialize
the hardware. When all transfers are done, the driver must call
spi_release_bus() to make the bus available to others, and possibly
shut down the SPI controller hardware.

spi_xfer() behaves mostly the same as before, but it now takes a
spi_slave parameter instead of a spi_chipsel function pointer. It also
got a new parameter, flags, which is used to specify chip select
behaviour. This may be extended with other flags in the future.

This patch has been build-tested on all powerpc and arm boards
involved. I have not tested NIOS since I don't have a toolchain for it
installed, so I expect some breakage there even though I've tried
fixing up everything I could find by visual inspection.

I have run-time tested this on AVR32 ATNGW100 using the atmel_spi and
DataFlash drivers posted as a follow-up. I'd like some help testing
other boards that use the existing SPI API.

But most of all, I'd like some comments on the new API. Is this stuff
usable for everyone? If not, why?

Changed in v4:
  - Build fixes for various boards, drivers and commands
  - Provide common struct spi_slave definition that can be extended by
    drivers
  - Pass a struct spi_slave * to spi_cs_activate and spi_cs_deactivate
  - Make default bus and mode build-time configurable
  - Override default SPI bus ID and mode on mx32ads and imx31_litekit.

Changed in v3:
  - Add opaque struct spi_slave for controller-specific data associated
    with a slave.
  - Add spi_claim_bus() and spi_release_bus()
  - Add spi_free_slave()
  - spi_setup() is now called spi_setup_slave() and returns a
    struct spi_slave
  - soft_spi now supports four SPI modes (CPOL|CPHA)
  - Add bus parameter to spi_setup_slave()
  - Convert the new i.MX32 SPI driver
  - Convert the new MC13783 RTC driver

Changed in v2:
  - Convert the mpc8xxx_spi driver and the mpc8349emds board to the
    new API.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Tested-by: Guennadi Liakhovetski <lg@denx.de>
2008-06-03 20:28:50 +02:00
Haavard Skinnemoen
289011207d Move definition of container_of() to common.h
AVR32 and AT91SAM9 both have their own identical definitions of
container_of() taken from the Linux kernel. Move it to common.h so
that all architectures can use it.

container_of() is already used by some drivers, and will be used
extensively by the new and improved SPI API.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-06-03 20:27:23 +02:00
Haavard Skinnemoen
110e006fe6 soft_i2c: Pull SDA high before reading
Spotted by Dean Capindale.

Systems that support open-drain GPIO properly are allowed provide an
empty I2C_TRISTATE define. However, this means that we need to be
careful not to drive SDA low when the slave is expected to respond.

This patch adds a missing I2C_SDA(1) to read_byte() required to
tristate the SDA line on systems that support open-drain GPIO.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-06-03 20:25:56 +02:00
Stefan Roese
3c1de1a6d3 ppc4xx: Remove implementations of testdram()
This patch removes the used testdram() implementations of the board
that are maintained by myself.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-06-03 20:22:24 +02:00
Stefan Roese
bbeff30cbd ppc4xx: Remove superfluous dram_init() call or replace it by initdram()
Historically the 405 U-Boot port had a dram_init() call in early init
stage. This function was still called from start.S and most of the time
coded in assembler. This is not needed anymore (since a long time) and
boards should implement the common initdram() function in C instead.

This patch now removed the dram_init() call from start.S and removes the
empty implementations that are scattered through most of the 405 board
ports. Some older board ports really implement this dram_init() though.
These are:

csb272
csb472
ERIC
EXBITGEN
W7OLMC
W7OLMG

I changed those boards to call this assembler dram_init() function now
from their board specific initdram() instead. This *should* work, but please
test again on those platforms. And it is perhaps a good idea that those
boards use some common 405 SDRAM initialization code from cpu/ppc4xx at
some time. So further patches welcome here.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-06-03 20:22:19 +02:00
Stefan Roese
192f90e272 ppc4xx: Use new 4xx SDRAM controller enable defines in common ECC code
Signed-off-by: Stefan Roese <sr@denx.de>
2008-06-03 20:22:13 +02:00
Stefan Roese
39b32be18c ppc4xx: Fix common ECC generation code for 440GP style platforms
This patch makes the common 4xx ECC code really usable on 440GP style
platforms.

Since the IBM DDR controller used on 440GP/GX/EP/GR is not register
compatible to the IBM DDR/2 controller used on 405EX/440SP/SPe/460EX/GT
we need to make some processor dependant defines used later on by the
driver.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-06-03 20:22:08 +02:00
Stefan Roese
ec724f883e ppc4xx: Change Kilauea to use the common DDR2 init function
This patch changes the kilauea and kilauea_nand (for NAND booting)
board port to not use a board specific DDR2 init routine anymore. Now
the common code from cpu/ppc4xx is used.

Thanks to Grant Erickson for all his basic work on this 405EX early
bootup.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-06-03 20:22:03 +02:00
Stefan Roese
17ceb069b8 ppc4xx: Consolidate PPC4xx SDRAM/DDR/DDR2 defines, part2
This patch now adds a new header file (asm-ppc/ppc4xx-sdram.h) for all
ppc4xx related SDRAM/DDR/DDR2 controller defines.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-06-03 20:21:58 +02:00
Stefan Roese
36ea16f6a0 ppc4xx: Consolidate PPC4xx SDRAM/DDR/DDR2 defines, part1
This patch removes all SDRAM related defines from the PPC4xx headers
ppc405.h and ppc440.h. This is needed since now some 405 PPC's use
the same SDRAM controller as 440 systems do (like 405EX and 440SP).

It also introduces new defines for the equipped SDRAM controller based on
which PPC variant is used. There new defines are:

used on 405GR/CR/EP and some Xilinx Virtex boards.

used on 440GP/GX/EP/GR.

used on 440EPx/GRx.

used on 405EX/r/440SP/SPe/460EX/GT.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-06-03 20:21:53 +02:00
Stefan Roese
64852d09e0 ppc4xx/NAND_SPL: Consolidate 405 and 440 NAND booting code in start.S
This patch consolidates the 405 and 440 parts of the NAND booting code
selected via CONFIG_NAND_SPL. Now common code is used to initialize the
SDRAM by calling initdram() and to "copy/relocate" to SDRAM/OCM/etc.
Only *after* running from this location, nand_boot() is called.

Please note that the initsdram() call is now moved from nand_boot.c
to start.S. I experienced problems with some boards like Kilauea
(405EX), which don't have internal SRAM (OCM) and relocation needs to
be done to SDRAM before the NAND controller can get accessed. When
initdram() is called later on in nand_boot(), this can lead to problems
with variables in the bss sections like nand_ecc_pos[].

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
2008-06-03 20:21:49 +02:00
Grant Erickson
8a24c07ba5 ppc4xx: Enable Primordial Stack for 40x and Unify ECC Handling
This patch (Part 2 of 2):

* Rolls up a suite of changes to enable correct primordial stack and
  global data handling when the data cache is used for such a purpose
  for PPC40x-variants (i.e. CFG_INIT_DCACHE_CS).

* Related to the first, unifies DDR2 SDRAM and ECC initialization by
  eliminating redundant ECC initialization implementations and moving
  redundant SDRAM initialization out of board code into shared 4xx
  code.

* Enables MCSR visibility on the 405EX(r).

* Enables the use of the data cache for initial RAM on
  both AMCC's Kilauea and Makalu and removes a redundant
  CFG_POST_MEMORY flag from each board's CONFIG_POST value.

  - Removed, per Stefan Roese's request, defunct memory.c file for
    Makalu and rolled sdram_init from it into makalu.c.

With respect to the 4xx DDR initialization and ECC unification, there
is certainly more work that can and should be done (file renaming,
etc.). However, that can be handled at a later date on a second or
third pass. As it stands, this patch moves things forward in an
incremental yet positive way for those platforms that utilize this
code and the features associated with it.

Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-06-03 20:21:20 +02:00
Grant Erickson
c821b5f120 ppc4xx: Enable Primordial Stack for 40x and Unify ECC Handling
This patch (Part 1 of 2):

* Rolls up a suite of changes to enable correct primordial stack and
  global data handling when the data cache is used for such a purpose
  for PPC40x-variants (i.e. CFG_INIT_DCACHE_CS).

* Related to the first, unifies DDR2 SDRAM and ECC initialization by
  eliminating redundant ECC initialization implementations and moving
  redundant SDRAM initialization out of board code into shared 4xx
  code.

* Enables MCSR visibility on the 405EX(r).

* Enables the use of the data cache for initial RAM on
  both AMCC's Kilauea and Makalu and removes a redundant
  CFG_POST_MEMORY flag from each board's CONFIG_POST value.

  - Removed, per Stefan Roese's request, defunct memory.c file for
    Makalu and rolled sdram_init from it into makalu.c.

With respect to the 4xx DDR initialization and ECC unification, there
is certainly more work that can and should be done (file renaming,
etc.). However, that can be handled at a later date on a second or
third pass. As it stands, this patch moves things forward in an
incremental yet positive way for those platforms that utilize this
code and the features associated with it.

Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-06-03 20:20:50 +02:00
Grant Erickson
a439680019 PPC4xx: Simplified post_word_{load, store}
This patch simplifies post_word_{load,store} by using the preprocessor
to eliminate redundant, copy-and-pasted code.

Signed-off-by: Grant Erickson <gerickson@nuovations.com>
2008-06-03 20:20:01 +02:00
Stefan Roese
10a3367955 Merge branch 'master' of /home/stefan/git/u-boot/u-boot 2008-06-03 20:19:08 +02:00
Kumar Gala
f979690ee3 Fix warnings from gcc-4.3.0 build on a ppc host
* The cfi_flash.c memset fix actual allows the board to boot so there is
  a bit more going on here than just resolving warnings associated with
  uninitialized variables.

* include/asm/bitops.h:302: warning: '__swab32p' is static but used in
  inline function 'ext2_find_next_zero_bit' which is not static

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-03 19:52:52 +02:00
Becky Bruce
9b124a6834 MPC512x: Change traps.c to not reference non-addressable memory
Currently, END_OF_RAM is used by the trap code to determine if
we should attempt to access the stack pointer or not. However,
on systems with a lot of RAM, only a subset of the RAM is
guaranteed to be mapped in and accessible.  Change END_OF_RAM
to use get_effective_memsize() instead of using the raw ram
size out of the bd.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-06-03 19:47:14 +02:00
Kumar Gala
81673e9ae1 Make sure common.h is the first include.
If common.h isn't first we can get CONFIG_ options defined in the
board config file ignored.  This can cause an issue if any of those
config options impact the size of types of data structures
(eg CONFIG_PHYS_64BIT).

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-03 19:42:05 +02:00
Marian Balakowicz
95d449ad4d Avoid initrd and logbuffer area overlaps
Add logbuffer to reserved LMB areas to prevent initrd allocation
from overlaping with it.

Make sure to use correct logbuffer base address.

Signed-off-by: Marian Balakowicz <m8@semihalf.com>
2008-06-03 19:34:19 +02:00
Sascha Laue
6956d53d99 lwmon5: add memory-pattern-test to FPGA POST. 2008-06-03 19:30:07 +02:00
Becky Bruce
e34a0e911b PPC: 86xx Add bat registers to reginfo command
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-06-03 18:05:15 +02:00
Becky Bruce
d5b9b8cdb8 PPC: Add print_bats() to lib_ppc/bat_rw.c
This function prints the values of all the BAT register
pairs - I needed this for debug earlier this week; adding it to
lib_ppc so others can use it (and add it to reginfo commands
if so desired).

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-06-03 18:03:03 +02:00
Becky Bruce
c148f24c15 PPC: Change lib_ppc/bat_rw.c to use high bats
Currently, this code only deals with BATs 0-3, which makes
it useless on systems that support BATs 4-7.  Add the
support for these registers.

Signed-off-by: Becky Bruce <Becky.bruce@freescale.com>
2008-06-03 18:01:24 +02:00
Becky Bruce
31d8267224 PPC: Create and use CONFIG_HIGH_BATS
Change all code that conditionally operates on high bat
registers (that is, BATs 4-7) to look at CONFIG_HIGH_BATS
instead of the myriad ways this is done now.  Define the option
for every config for which high bats are supported (and
enabled by early boot, on parts where they're not always
enabled)

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-06-03 17:48:41 +02:00
Ben Warren
ea183432e7 Merge branch 'master' of git://www.denx.de/git/u-boot 2008-06-02 22:55:42 -07:00
Wolfgang Grandegger
aa3b8bf9c3 E1000: Add support for the 82541GI LF Intel Pro 1000 GT Desktop Adapter
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-06-02 22:39:20 -07:00
TsiChung Liew
ff36fbb2e7 ColdFire: Add 10 base ethernet support for mcf5445x
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-06-02 22:38:53 -07:00