This adds support for "nvmem cells" as seen in Linux. The nvmem device
class in Linux is used for various assorted ROMs and EEPROMs. In this
sense, it is similar to UCLASS_MISC, but also includes
UCLASS_I2C_EEPROM, UCLASS_RTC, and UCLASS_MTD. New drivers corresponding
to a Linux-style nvmem device should be implemented as one of the
previously-mentioned uclasses. The nvmem API acts as a compatibility
layer to adapt the (slightly different) APIs of these uclasses. It also
handles the lookup of nvmem cells.
While nvmem devices can be accessed directly, they are most often used
by reading/writing contiguous values called "cells". Cells typically
hold information like calibration, versions, or configuration (such as
mac addresses).
nvmem devices can specify "cells" in their device tree:
qfprom: eeprom@700000 {
#address-cells = <1>;
#size-cells = <1>;
reg = <0x00700000 0x100000>;
/* ... */
tsens_calibration: calib@404 {
reg = <0x404 0x10>;
};
};
which can then be referenced like:
tsens {
/* ... */
nvmem-cells = <&tsens_calibration>;
nvmem-cell-names = "calibration";
};
The tsens driver could then read the calibration value like:
struct nvmem_cell cal_cell;
u8 cal[16];
nvmem_cell_get_by_name(dev, "calibration", &cal_cell);
nvmem_cell_read(&cal_cell, cal, sizeof(cal));
Because nvmem devices are not all of the same uclass, supported uclasses
must register a nvmem_interface struct. This allows CONFIG_NVMEM to be
enabled without depending on specific uclasses. At the moment,
nvmem_interface is very bare-bones, and assumes that no initialization
is necessary. However, this could be amended in the future.
Although I2C_EEPROM and MISC are quite similar (and could likely be
unified), they present different read/write function signatures. To
abstract over this, NVMEM uses the same read/write signature as Linux.
In particular, short read/writes are not allowed, which is allowed by
MISC.
The functionality implemented by nvmem cells is very similar to that
provided by i2c_eeprom_partition. "fixed-partition"s for eeproms does
not seem to have made its way into Linux or into any device tree other
than sandbox. It is possible that with the introduction of this API it
would be possible to remove it.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Add some fallback functions for when i2c_eeprom is disabled. This allows
code to reference i2c_eeprom_* functions without needing to check
whether support has been compiled in.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
i2c_eeprom_ops->write uses a const buf, so use one for the wrapper
function as well.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When the device returns used buffers, it should refer to the descriptor
that is the head of the descriptor chain for that buffer. Confirm this
to be the case by tracking the head of descriptor chains that have been
made available to the device.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The shared descriptors should only be written by the guest driver,
however, the device is still able to overwrite and corrupt them.
Maintain a private shadow copy of the descriptors for the driver to
use for state tracking, removing the need to read from the shared
descriptors.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
rootwait=1 is not a valid kernel boot parameters. According
to the documenation is only rootwait
rootwait [KNL] Wait (indefinitely) for root device to show up.
Useful for devices that are detected asynchronously
(e.g. USB and MMC devices).
Fix:
Unknown kernel command line parameters "rootwait=1", will be passed to user space.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The bi_enetaddr field in struct bd_info is write-only; nothing ever
reads back the value.
Moreover, the value we write is more or less random, and certainly not
something one can rely on: If the board has a writable environment and
the mac address has been stored there, we fetch that value. But if the
board doesn't, this code runs before initr_net() -> eth_initialize(),
and thus before the code in eth-uclass which fetches MAC addresses
from eeprom, fuses or whatnot and populates the (run-time) environment
with those values.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Tom Rini <trini@konsulko.com>
Static events do not currently work post-relocation for boards that enable
CONFIG_NEEDS_MANUAL_RELOC. Relocate event handler pointers for all event
spies to fix this.
Tested on Microblaze.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
CONFIG_DM_EVENT without CONFIG_EVENT is non-functional.
Let CONFIG_DM_EVENT depend on CONFIG_EVENT.
Remove superfluous stub in include/event.h.
Fixes: 5b896ed585 ("event: Add events for device probe/remove")
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
CONFIG_SPL_BOOT_DEVICE was made obsolete by
CONFIG_MVEBU_SPL_BOOT_DEVICE_{SPI,MMC,SATA,UART}.
CONFIG_MVEBU_SPL_BOOT_DEVICE_SPI is the default so existing users of
CONFIG_SPL_BOOT_DEVICE can simply have the option removed.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
CONFIG_FIXED_SDHCI_ALIGNED_BUFFER is needed on some Marvell SoCs when
booting from MMC. All existing usages of this have the same value so
make this the default and have the Kconfig option depend on SPL &&
MVEBU_SPL_BOOT_DEVICE_MMC.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR
CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS
Signed-off-by: Tom Rini <trini@konsulko.com>
In some cases, when we don't use CONFIG_SPL_FRAMEWORK nor are we on
PowerPC using their specific SPL/TPL framework, we need to specify the
start.S file to use for these typically very constrained systems. Do
this within the Makefile logic, rather than introducing a string-based
CONFIG option, as this would get slightly complex to do in Kconfig for a
very limited number of users.
Signed-off-by: Tom Rini <trini@konsulko.com>
The address where the device tree will be passed in to U-Boot at is now
moved to the Kconfig file. If this is user configurable, it needs to be
exposed rather than hidden, and should probably be renamed as well.
Reviewed-by: Rick Chen <rick@andestech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_SPL_ARGS_ADDR
In doing so, we also consistently use this variable for SPL_OS_BOOT and
not CONFIG_SYS_FDT_BASE in some cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
This is mostly unused. In the case where it is currently used, it means
the same as CONFIG_SPL_PAD_TO, which is already set for the platform.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_SPL_MALLOC_SIZE
CONFIG_SYS_SPL_MALLOC_START
We introduce a default value here as well, and CONFIG_SYS_SPL_MALLOC to
control if we have a malloc pool or not.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_RELOC_TEXT_BASE
CONFIG_SPL_RELOC_STACK
CONFIG_SPL_RELOC_MALLOC_ADDR
CONFIG_SPL_RELOC_MALLOC_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
Update the Kconfig entry to have the correct defaults for i.MX7
platforms, and move the existing large comment from imx7_spl.h to
doc/imx/common/imx7.txt so that it's not lost.
Signed-off-by: Tom Rini <trini@konsulko.com>
Update the Kconfig entry to have the correct defaults for i.MX6
platforms, and move the existing large comment from imx6_spl.h to
doc/imx/common/imx6.txt so that it's not lost.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a number of CONFIG symbols today that are of the form:
SYM1 = CONST1 + CONST2
or other static math operations (shifts, etc). The issue is that by
moving these to Kconfig we no longer have the ability to calculate these
values, so they become less flexible and useful. It's also the case
that sometimes a platform will just define SYM1 directly or perform a
slightly different set of calculations. We introduce this header now to
have a place to start to handle these cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have GENERATED_GBL_DATA_SIZE to tell us how large the generated
global data is, so do not use a hard-coded value of 1024 for it.
Signed-off-by: Tom Rini <trini@konsulko.com>
In the places where PowerPC references CONFIG_SYS_GBL_DATA_OFFSET it
does so as (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET). And
it defines CONFIG_SYS_GBL_DATA_OFFSET in the same manner that other
architectures define CONFIG_SYS_INIT_SP_OFFSET. Other architectures
define CONFIG_SYS_INIT_SP_ADDR as (CONFIG_SYS_INIT_RAM_ADDR +
CONFIG_SYS_INIT_SP_OFFSET) typically. Rename things within PowerPC for
consistency with other architectures.
Signed-off-by: Tom Rini <trini@konsulko.com>
This value is only referenced by PowerPC code in a way other than
directly as CONFIG_SYS_INIT_SP_ADDR. Switch to CONFIG_SYS_INIT_SP_ADDR
directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
This value is only referenced by PowerPC code in a way other than
directly as CONFIG_SYS_INIT_SP_ADDR. Switch to CONFIG_SYS_INIT_SP_ADDR
directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
In some cases, we define CONFIG_SYS_INIT_SP_ADDR differently for SPL or
full U-Boot. This case should be making use of CONFIG_SPL_STACK, as
that's what that variable is for. In a few other cases we define
CONFIG_SPL_STACK directly to CONFIG_SYS_INIT_SP_ADDR, but do not need to
as the code handles this correctly, normally.
Signed-off-by: Tom Rini <trini@konsulko.com>
The definition of CONFIG_SPL_BOOTROM_SAVE is always a fixed
CONFIG_SPL_STACK + 4, while CONFIG_SPL_STACK is not constant. This
change will make it clear where the location is still, once
CONFIG_SPL_STACK moves to Kconfig.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
A number of PowerPC platforms define this, for SPL. To move this to
Kconfig, it needs to be CONFIG_SPL_SYS_CCSR_DO_NOT_RELOCATE, so use
CONFIG_IS_ENABLED() to check for usage. A number of layerscape
platforms bring this logic from PowerPC, but only need a small part of
it, for the fman driver. Remove their unused portion at least.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_SYS_MALLOC_SIMPLE
The problem here is that a few platforms have been doing:
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MALLOC_SIMPLE
#endif
instead of defining CONFIG_SPL_SYS_MALLOC_SIMPLE directly. Correct this
and update the documentation in a few places to match usage.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_BSS_MAX_SIZE
CONFIG_SPL_MAX_FOOTPRINT
Note that the da850evm platforms were violating the "only use one" rule
here, and so now hard-code their BSS limit.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_PAD_TO
CONFIG_SPL_MAX_SIZE
CONFIG_TPL_PAD_TO
CONFIG_TPL_MAX_SIZE
Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the
existing places.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_FS_LOAD_ARGS_NAME
CONFIG_SPL_FS_LOAD_KERNEL_NAME
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_INIT_MINIMAL
CONFIG_SPL_FLUSH_IMAGE
CONFIG_SPL_SKIP_RELOCATE
Signed-off-by: Tom Rini <trini@konsulko.com>
This is only referenced in non-SPL_DM cases, of which there are
currently none. Remove this option and slightly re-organize the code is
there is now never an if/else at the start of spl_sata_load_image()
Signed-off-by: Tom Rini <trini@konsulko.com>
