So far the switch is initialized in probe stage and is connected to PSE
unconditionally. This will cause all packets being flooded to PSE and may
cause PSE hang before entering linux.
This patch changes the connection between switch and PSE:
- Still initialize switch in probe stage, but disconnect it with PSE
- Connect switch with PSE on eth start
- Disconnect on eth stop
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The original mediatek pinctrl functions for driving configuration
'mtk_pinconf_drive_set_*' do not return -ENOSUPP even if input
parameters are not supported.
This patch fixes the return value in those functions.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
There exists a situation of the mediatek pinctrl driver that may return
wrong pin function value for the pinmux driver:
- All pin function arrays are defined without const
- Some pin function arrays contain all-zero value, e.g.:
static int mt7622_spi_funcs[] = { 0, 0, 0, 0, 0, 0, };
- These arrays will be put into .bss section during compilation
- .bss section has no "a" attribute and does not exist in the final binary
file after objcopy.
- FDT binary blob is appended to the u-boot binary, which occupies the
.bss section.
- During board_f stage, .bss has not been initialized, and contains the
data of FDT, which is not full-zero data.
- pinctrl driver is initialized in board_f stage, and it will get wrong
data if another driver is going to set default pinctrl.
Since pinmux information and soc data are only meant to be read-only, thus
should be declared as const. This will force all pinctrl data being put
into .rodata section. Since .rodata has "a" attribute, even the all-zero
data will be allocated and filled with correct value in to u-boot binary.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
MT7981 actually uses MediaTek I2C controller v3 instead of v1.
This patch adds support for I2C controller v3 fix fixes the I2C usability
for MT7981.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch add missing return value check for allocating the driver's
private data. -ENOMEM will be returned if malloc() fails.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch ensures driver private data being fully initialized in
_debug_uart_init which is not covered by .priv_auto ops.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Stefan Roese <sr@denx.de>
In u-boot we don't use IRQ. Instead, we poll busy bit in SPI_STATUS.
However these IRQ enable bits may be set in previous boot stage (BootROM).
If we leave these bits not cleared, although u-boot has disabled IRQ and
nothing will happen, the linux kernel may encounter panic during
initializing the spim driver due to IRQ event happens before IRQ handler
is properly setup.
This patch clear IRQ bits to prevent this from happening.
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
We don't really need to switch clk rate during operating SPIM controller.
Get clk rate only once at driver probing.
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add rtl8169 NIC device ID and reorder the device ID.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
For RISC-V architeture, hardware maintain the dcache coherency.
Software do not flush the cache. So even cache-line size larger
than descriptor size, driver can work.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
While compiling rtl8169.c, There are many "make pointer from
integer without a cast" compile warnings. fix them with
adding cast.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add pcie driver for StarFive JH7110, Also add PLDA
PCIe controller common driver functions.
Several devices are tested:
a) M.2 NVMe SSD
b) Realtek 8169 Ethernet adapter.
Signed-off-by: Mason Huo <mason.huo@starfivetech.com>
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Acked-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
As the Designware_i2c_pci.c uses ACPI APIs, If some SoCs (StarFive
JH7110) contain Designware i2c and PCI but do not use ACPI,
This file cannot be compiled. So add a new Kconfig for
designware_i2c_pci.c, which depends on ACPIGEN
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
- Add a little more info to 'cbsysinfo' command
-----BEGIN PGP SIGNATURE-----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=s8Ab
-----END PGP SIGNATURE-----
Merge tag 'x86-pull-20230801' of https://source.denx.de/u-boot/custodians/u-boot-x86
- MTRR fixes for x86 boards
- Add a little more info to 'cbsysinfo' command
- bochs: remove the x86 limitation
- correct kconfig text for PCI default FB size
- kconfig: drop the superfluous PCI dependency
- set up default FB size for Bochs
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCZMj+xA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXPovAJ9DU0H3Xm9LmrPZE4NzmmkfKJ/99QCfTlDfIkZI
dVilMWOHsRX1SgMS6YM=
=KYKc
-----END PGP SIGNATURE-----
Merge tag 'video-20230801' of https://source.denx.de/u-boot/custodians/u-boot-video
- dm video cosmetic style fix
- bochs: remove the x86 limitation
- correct kconfig text for PCI default FB size
- kconfig: drop the superfluous PCI dependency
- set up default FB size for Bochs
Perform removal of DSS if kconfigs VIDEO_REMOVE or SPL_VIDEO_REMOVE is
set by user. Otherwise if above Kconfigs are not selected, it is assumed
that user wants splash screen to be displayed until linux kernel boots
up. In such scenario, leave the power domain of DSS as "on" so that
splash screen stays intact until kernel boots up.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Change remove method of DSS video driver to disable video port instead
of performing a soft reset, as soft reset takes longer duration. Video
port is disabled by setting enable bit of video port to 0.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
At present the uclass stored frame buffer size is set to a hard
coded value, but we can calculate the correct value based on what
is configured.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # qemu-x86_64
Set up a default frame buffer size of 8MiB for Bochs for non-x86
architecturs as PCI is normally not enumerated before relocation
on these architectures.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
PCI is always selected by X86 architecture hence "X86 && PCI" does
not make it better.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # qemu-x86_64
There is an example in the VIDEO_PCI_DEFAULT_FB_SIZE help text to
tell people how to calculate its value but the resolution given
does not match the value. Fix it.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that the driver is legacy free, remove the x86 dependency so
that it can be used on non-x86 architectures.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # qemu-x86_64
At present the driver uses IO instructions to access the legacy
VGA IO ports, which unfortunately limits the driver to work only
on x86. It turns out the IO instruction is not necessary as Bochs
VGA card remaps the legacy VGA IO ports (0x3c0 -> 0x3df) to its
memory mapped register space from offset 0x400.
Update the driver to use MMIO access for VGA IO port.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # qemu-x86_64
bochs_vga_write() takes 'index' as one argument, but never uses it.
While we are here, use macros instead of magic numbers for the
VGA IO port register name and value.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # qemu-x86_64
The driver does not call any MTRR APIs.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # qemu-x86_64
Some coding convention fixes for video_post_bind().
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # qemu-x86_64
At present this uses mtrr_add_request() & mtrr_commit() combination
to program the MTRR for graphics memory. This usage has two major
issues as below:
- mtrr_commit() will re-initialize all MTRR registers from index 0,
using the settings previously added by mtrr_add_request() and saved
in gd->arch.mtrr_req[], which won't cause any issue but is unnecessary
- The way such combination works is based on the assumption that U-Boot
has full control with MTRR programming (e.g.: U-Boot without any blob
that does all low-level initialization on its own, or using FSP2 which
does not touch MTRR), but this is not the case with FSP. FSP programs
some MTRRs during its execution but U-Boot does not have the settings
saved in gd->arch.mtrr_req[] and when doing mtrr_commit() it will
corrupt what was already programmed previously.
Correct this to use mtrr_set_next_var() instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present this uses mtrr_add_request() & mtrr_commit() combination
to program the MTRR for graphics memory. This usage has two major
issues as below:
- mtrr_commit() will re-initialize all MTRR registers from index 0,
using the settings previously added by mtrr_add_request() and saved
in gd->arch.mtrr_req[], which won't cause any issue but is unnecessary
- The way such combination works is based on the assumption that U-Boot
has full control with MTRR programming (e.g.: U-Boot without any blob
that does all low-level initialization on its own, or using FSP2 which
does not touch MTRR), but this is not the case with FSP. FSP programs
some MTRRs during its execution but U-Boot does not have the settings
saved in gd->arch.mtrr_req[] and when doing mtrr_commit() it will
corrupt what was already programmed previously.
Correct this to use mtrr_set_next_var() instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present this uses mtrr_add_request() & mtrr_commit() combination
to program the MTRR for graphics memory. This usage has two major
issues as below:
- mtrr_commit() will re-initialize all MTRR registers from index 0,
using the settings previously added by mtrr_add_request() and saved
in gd->arch.mtrr_req[], which won't cause any issue but is unnecessary
- The way such combination works is based on the assumption that U-Boot
has full control with MTRR programming (e.g.: U-Boot without any blob
that does all low-level initialization on its own, or using FSP2 which
does not touch MTRR), but this is not the case with FSP. FSP programs
some MTRRs during its execution but U-Boot does not have the settings
saved in gd->arch.mtrr_req[] and when doing mtrr_commit() it will
corrupt what was already programmed previously.
Correct this to use mtrr_set_next_var() instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Update dwc3 generic driver and update support for rk3568/rk3328;
- Add boards:
rk3566: Pine64 Quartz64-A/B, SOQuartz on Model A/Blade/CM4-IO
rk3568: Radxa E25 Carrier Board
rk3588: Radxa ROCK5A
- Fixes and updates for chromebook veryon/jerry/speedy;
- SPI support fixes for rk3399/rk3568/rk3588;
- rk3588 usbdp phy support;
- dts and config updates for different boards;
Handle USB480M clock ID in set_rate() and set_parent()
to allow the dt assigned-clocks and assigned-clock-parents
work on rk3328.dtsi
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
USB2.0 Host and OTG controllers in RK3328 are using USB2PHY.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Like Rockchip RK3568, the RK3328 also have single node to
represent the glue and ctrl for USB 3.0.
So, use the driver data to use single ctrl for RK3328 DWC3.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A quick power cycle of a LDO regulator during dw-mmc signal voltage
change has shown that SD-card does not always get recognized.
Linux driver use an enable_time of 400us for LDO regulators. Apply a
500us delay when a LDO regulator is enabled to fix possible issues.
Fixes: 94afc1cb46 ("power: regulator: rk8xx: update the driver for rk808 and rk818")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: elaine.zhang<elaine.zhang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
gpio_request_list_by_name() returns the number of gpios requested.
Notably it swallows the underlying -ENOENT when the "gpios" property
does not exist.
Update the i2c-gpio driver to check for ret == 0 before trying the new
sda-gpios/scl-gpios properties.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
RK3568 share glue and ctrl in a single node. Use glue_get_ctrl_dev to
return the glue node as the ctrl node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Marek Vasut <marex@denx.de>
When dr_mode is peripheral or otg and U-Boot has not been built with
DM_USB_GADGET support, booting such device may end up with:
dwc3_glue_bind_common: subnode name: usb@fcc00000
Error binding driver 'dwc3-generic-wrapper': -6
Some drivers failed to bind
initcall sequence 00000000effbca08 failed at call 0000000000a217c8 (err=-6)
### ERROR ### Please RESET the board ###
Instead fail gracfully with ENODEV to allow board continue booting.
dwc3_glue_bind_common: subnode name: usb@fcc00000
dwc3_glue_bind_common: unsupported dr_mode 3
Also use CONFIG_IS_ENABLED(USB_HOST) and change switch to if statements
to improve readability of the code.
Fixes: 446e3a205b ("dwc3-generic: Handle the PHYs, the clocks and the reset lines")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marex@denx.de>
The current error check for device_find_first_child is not working as
expected, the documentation for device_find_first_child mention:
@devp: Returns first child device, or NULL if none
Return: 0
Change to return early when there is no child node to avoid any possible
null pointer dereference.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CONFIG_SPL_PCI_PNP=y without CONFIG_SPL_PCI=y makes no sense.
Fixes: 32f5e9e5c1 ("nvme: pci: Enable for SPL")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
- Resync some of the K3 DTS files with the kernel, and pull in some
required related updates to keep drivers in sync with the dts files
now. Bring in some incremental fixes on top of one of the series I
applied recently as well as updating the iot2050 platform. Also do a
few small updates to the K2 platforms.
- Enable pcie support for rk3568;
- Add boards:
rk3399: Radxa ROCK 4SE;
rk3328: Orange Pi R1 Plus, Orange Pi R1 Plus LTS
rk3568: FriendlyARM NanoPi R5S/R5C, Hardkernel ODROID-M1
rk3588: Edgeble Neu6B
- support OP-TEE with binman;
- support Winbond SPI flash;
- rk3588 usbdp phy support;
- dts and config updates for different boards;
The TI AM654 timer is compatible with the omap-timer implementation,
so add it to the compatible id list.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Cc: Francesco Dolcini <francesco@dolcini.it>
Cc: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
The dwc_ahci driver use platform specific defines, place the platform
specific code behind a ifdef CONFIG_ARCH_OMAP2PLUS to allow build and
use of the driver on Rockchip platform.
Fixes: 02a4b42979 ("drivers: block: dwc_ahci: Implement a driver for Synopsys DWC sata device")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
