Function dm_pci_hose_probe_bus() expects that bus is valid PCI device with
Bridge header type (0x01). So add check before touching PCI config space to
prevent misconfiguring some non-standard device.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
PCI Rom Address is currently supported only for Normal (0x00) and
Bridge (0x01) header types. Fix code accordingly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The current code invalidates the range after the read buffer since the
buffer pointer gets incremented in the read loop. Use a temporary
pointer to make sure we have a pristine pointer to invalidate the
correct memory range after read.
Fixes: 704e040a51 ("nvme: Apply cache operations on the DMA buffers")
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
The DS1307 driver was originally based on the DS1337 driver. However,
the functionality of the clock set/get functions has diverged. In the
original DS1337 driver, the set/get functions did the following:
1) Setting the clock ensured the oscillator was enabled.
2) Getting the clock checked and reset the oscillator-stop flag.
The DS1307 does not have an oscillator-stop flag, but the driver tried
(incorrectly) to emulate this by ensuring the oscillator was running. It
really makes no sense to start a stopped clock without setting it.
This patch makes the DS1307 driver behave like the original DS1337
driver again. For the DS1307 itself, this is just a removal of code,
since there is no oscillator-fail bit to check or reset, and the clock
is started when it is set. Since the DS1307 driver can now also be used
for the DS1337 and DS1340 which do have this bit, add code to handle the
oscillator-stop bit in the same was the original DS1337 driver did --
i.e. report that the oscillator had stopped and clear the flag.
This means that setting the date using the date command (which does both
a get and a set) will now clear the oscillator-stop flag in addition to
setting and starting the clock.
The old-style (non-DM) code has not been updated and will be removed in
a future patch. Note that this older code does not support the DS1337,
as there is a separate driver for this. Also note that the original (DM)
code used the wrong control-register address for the DS1337.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Add a driver for Macronix raw NAND controller.
This patch referred from linux mxic_nand.c. The difference from the
linux version is described here.
1. In order to adapt to the uboot nand framework, add function
binding (cmdfunc, read_byte, read_buf, write_buf).
2. Added parsing command format to use hardware correctly.
3. Remove the incompatible functions of Uboot.
Signed-off-by: Zhengxun Li <zhengxunli@mxic.com.tw>
strlcat() need to be passed the full buffer length. The incorrect call
caused truncation of partition names for fastboot_raw_partition_... and
fastboot_partition_alias_... env lookup to much less than PART_NAME_LEN.
Fixes: 69a7529831 ("fastboot: Fix possible buffer overrun")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
-----BEGIN PGP SIGNATURE-----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=S4kl
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211012' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Disable ATAGS for STM32 MCU and MPU boards
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
Signed-off-by: Tom Rini <trini@konsulko.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmFlfXAcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyHzuB/4pV2iAeFBjNf6YYsuk
uvBQm7+j+AQzy0J337bDwulvw8wTKKlaid4qfOpEjW316DI9oXN1bXTlwNsjtQvO
zTILW7MoBjDRhZHsSkeSfIuD+Sc80juAoLBv+GXskQdZOTQUbWdmi2o60gdY5Ba4
WN0i4zOGVqd7xoDuDgM3XC1M2RnKerxDeVt20Ji+5dFfmes11m7br6sWj2j/45f+
q3G1ufHl+ea+8oRLZGjn2ddKCb1wLLOrNZA+74dsZ5SN0LCN0vFsE3+JAk4RZ2A5
omiHVApjE+J3vAjwiVY7apjcIdVEeyb5AioiXSBAEZiq1l1UI7eKDQT75bDkaKSs
4wBV
=78ME
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.01-b' of https://source.denx.de/u-boot/custodians/u-boot-at91
Second set of u-boot-at91 features for the 2022.01 cycle:
This small feature set adds the support for PWM driver for the sama5d2
SoC. It also adds a node in the DT for this SoC.
The bulk of it is Samuel's DM_I2C rework, which removes the nasty I2C
deprecation warnings for most 32-bit boards. It also includes some
smaller refactorings that pave the way for more changes, mostly driven
by needing to support the Allwinner RISC-V SoC later on.
Board wise we gain support for the FriendlyARM NanoPi R1S H5 router
board and official Pinetab support.
Build-tested for all 160 sunxi boards, and boot tested on a A64, A20,
H3, H6, and H616 board. USB, SD card, eMMC, and Ethernet all work there
(where applicable).
Add usb_gadget_handle_interrupts(), usb_gadget_register_driver()
and usb_gadget_unregister_driver() to be able to test
binding usb gadget.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add an entry in usb_gadget_controller_number() for the DWC2
gadget controller. It is used to bind the USB Ethernet driver.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reported-by: Herbert Poetzl <herbert@13thfloor.at>
Cc: Marek Vasut <marex@denx.de>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Fix a regression brings by commit 84f8e36f03 ("cmd: bind: allow to
bind driver with driver data")
As example, the following bind command doesn't work:
bind /soc/usb-otg@49000000 usb_ether
As usb_ether driver has no compatible string, it can't be find by
lists_bind_fdt(). In bind_by_node_path(), which called lists_bind_fdt(),
the driver entry is known, pass it to lists_bind_fdt() to force the driver
entry selection.
For this, add a new parameter struct *driver to lists_bind_fdt().
Fix also all lists_bind_fdt() callers.
Fixes: 84f8e36f03 ("cmd: bind: allow to bind driver with driver data")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reported-by: Herbert Poetzl <herbert@13thfloor.at>
Cc: Marek Vasut <marex@denx.de>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Two displays supported by the sunxi display driver (each one used by a
single board) require initialization over I2C. Both previously used
i2c_soft; replace this with the i2c-gpio instance that already exists in
those boards' device trees (sun5i-a13-utoo-p66 and sun6i-a31-colombus).
Since the i2c-gpio nodes are not referenced by any other node in the
device trees (the device trees have no panel node), the I2C bus is
selected by its node name.
This panel initialization code was the only i2c_soft user, so the
i2c_soft GPIO setup code can be removed now as well.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This bus controller is used to communicate with an X-Powers AXP PMIC.
Currently, various drivers access PMIC registers through a platform-
specific non-DM "pmic_bus" interface, which depends on the legacy I2C
framework. In order to convert those drivers to use DM_PMIC, this bus
needs a DM_I2C driver.
Refactor the rsb functions to take the base address as a parameter,
and implement both the existing interface (which is still needed in
SPL) and the DM_I2C interface on top of them.
The register for switching between I2C/P2WI/RSB mode is the same across
all PMIC variants, so move that to the common header.
There are only a couple of pairs of hardware/runtime addresses used
across all PMIC variants. So far the code expected only the "primary"
pair, but some PMICs like the AXP305 and AXP805 use the secondary pair,
so add support for that to the DM driver as well.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This bus controller is used to communicate with an X-Powers AXP PMIC.
Currently, various drivers access PMIC registers through a platform-
specific non-DM "pmic_bus" interface, which depends on the legacy I2C
framework. In order to convert those drivers to use DM_PMIC, this bus
needs a DM_I2C driver.
Refactor the p2wi functions to take the base address as a parameter,
and implement both the existing interface (which is still needed in
SPL) and the DM_I2C interface on top of them.
The register for switching between I2C/P2WI/RSB mode is the same across
all PMIC variants. Move that to the common header, so it can be used by
both interface implementations.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
These PMICs provide some combination of battery charger, fuel gauge,
GPIOs, regulators, and VBUS routing. These functions are represented
as child nodes in the device tree. Add the minimal driver needed to
probe these child devices and provide the DM_PMIC ops.
Enable the driver by default for SoCs that normally pair with a PMIC.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Now that there is a separate symbol to enable DM_PMIC in SPL, update the
the SPL-specific driver symbols to depend on this new option.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Kconfig symbols for two PMIC drivers (PMIC_AS3722 and DM_PMIC_MC34708)
were missing a dependency on DM_PMIC. To fix this inconsistency, and to
keep it from happening again, wrap the driver section with "if DM_PMIC"
instead of using a "depends on DM_PMIC" clause for each driver.
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The patch enables spread spectrum clocking (SSC) for MPU and LCD PLLs.
As reported by the TI spruh73x/spruhl7x RM, SSC is only supported for
the DISP/LCD and MPU PLLs on am33xx/am43xx. SSC is not supported for
DDR, PER, and CORE PLLs.
Calculating the required values and setting the registers accordingly
was taken from the set_mpu_spreadspectrum routine contained in the
arch/arm/mach-omap2/am33xx/clock_am33xx.c file of the u-boot project.
In locked condition, DPLL output clock = CLKINP *[M/N]. In case of
SSC enabled, the reference manual explains that there is a restriction
of range of M values. Since the clk_ti_am3_dpll_round_rate() attempts
to select the minimum possible N, the value of M obtained is not
guaranteed to be within the range required. With the new "ti,min-div"
parameter it is possible to increase N and consequently M to satisfy the
constraint imposed by SSC.
Link: https://lore.kernel.org/r/20210606202253.31649-6-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Add a driver so the clocks/resets for these peripherals (especially I2C,
RSB, and UART) can be enabled using the normal uclass methods.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently, the I2C clocks are configured in the sunxi board code. Add
the I2C clocks to the DM clock driver so they can be enabled from the
DM I2C driver using the normal uclass methods.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Since the beginning, all banks have had space for 32 pins, even when
not all pins were implemented. Let's use a single constant for the GPIO
bank size here, like the GPIO driver is already doing.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This clarifies which callers must be updated to complete the DM_GPIO
conversion.
The only remaining caller of name_to_gpio in generic code is inside the
!DM_GPIO block in cmd/gpio.c. DM_GPIO is always selected on sunxi, so
that code cannot be reached. And after this commit, there are only two
remaining implementations of name_to_gpio.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
As part of migrating to DM_GPIO and DM_PINCTRL, eventually we will
remove the asm/arch/gpio.h header. In preparation, clean up the various
files that include it.
Some files did not contain any GPIO code at all, so this header was
completely unused.
A few files contained only legacy platform-specific GPIO code for
setting up pin muxes. They were left unchanged, as that code will be
completely removed by the DM_PINCTRL migration.
The remaining files contain some combination of DM_GPIO and legacy GPIO
code. For those, switch to including asm/gpio.h (if it wasn't included
already). Right now, this header provides both sets of functions,
because ARCH_SUNXI selects GPIO_EXTRA_HEADER. This will still be the
right header to include once the DM_GPIO migration is complete and
GPIO_EXTRA_HEADER is no longer needed.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The only caller of this function was the MMC pinmux code, which used it
to parse a string given from a Kconfig symbol. As the Kconfig symbol has
been converted to a Boolean, this function is no longer needed.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The CCU header is only used by the DM drivers, not any platform code.
Its current location adds an artificial dependency on CONFIG_ARM and
ARCH_SUNXI, which will be problematic when adding the CCU driver for
a RISC-V sunxi platform.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Move CONFIG_VIDEO_MXS from board headers to Kconfig
and drop it from obsolete cfb_console driver.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add support for 30bpp mode where pixels are picked in 32-bit
integers but use 10 bits instead of 8 bits for each component.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Compute i2cclk only one time in stm32_i2c_compute_timing()
and remove setup parameter (accessible in i2c_priv).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the support for the i2c-digital-filter binding, allowing to enable
the digital filter via the device-tree and indicate its value in the DT
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The digital filter related computation are present in the driver
however the programming of the filter within the IP is missing.
The maximum value for the DNF is wrong and should be 15 instead of 16.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Replace driver internally coded enabling/disabling of the
analog-filter with the DT binding "i2c-analog-filter".
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Today all the I2C instance point on the same global
variable stm32_i2c_setup according the compatible: i2c_priv->setup =
pointer to the same driver data.
This patch changes this driver data (stm32f7_setup and stm32mp15_setup)
to a const struct and move the timing struct 'setup' as element of i2c
privdata, initialized in stm32_ofdata_to_platdata() with the driver
configuration data.
This patch solves issues when several I2C instance have not the same
clock source or not the same configuration: each timing setup is saved
is the I2C privdata.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
There were several changes for this structure but the documentation was
not changed at the time. Fix this.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that PCI Bridge (PCIe Root Port) for Aardvark is emulated in U-Boot,
add support for handling and propagation of CRSSVE bit.
When CRSSVE bit is unset (default), driver has to reissue config
read/write request on CRS response.
CRSSVE bit is supported only when CRSVIS bit is provided in read-only
Root Capabilities register. So manually inject this CRSVIS bit into read
response for that register.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that PCI Bridge is working for the PCIe Root Port, U-Boot's PCI_PNP
code automatically enables memory access and bus mastering when needed.
We do not need to enable it when setting the HW up.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Aardvark does not have a real PCIe Root Port device on the root bus.
Instead it has PCIe registers of PCIe Root Port device mapped in
internal Aardvark memory space starting at offset 0xc0.
The PCIe Root Port itself is normally available as a PCI Bridge device
on the root bus with bus number zero. Aardvark instead has the
configuration registers of this PCI Bridge at offset 0x00 of Aardvark's
memory space, but the class code of this device is Mass Storage
Controller (0x010400), instead of PCI Bridge (0x600400), which causes
U-Boot to fail to recognize it as a P2P Bridge
Add a hook into the pcie_advk_read_config() / pcie_advk_write_config()
functions to redirect access for root bus from PIO transfer to this
internal Aardvark memory space. This will allow U-Boot to access
configuration space of this PCI Bridge which represents PCIe Root Port.
Redirect access to PCI Bridge registers in range 0x10 - 0x34 to driver's
internal buffer (cfgcache[]). This is because at those addresses
Aardvark has different registers, incompatible with config space of a
PCI Bridge.
Redirect access to PCI Bridge register PCI_ROM_ADDRESS1 (0x38) to
Aardvark internal address for that register (0x30).
When reading PCI Bridge register PCI_HEADER_TYPE, set it explicitly to
value Type 1 (PCI_HEADER_TYPE_BRIDGE) as PCI Bridge must be of Type 1.
When writing to PCI_PRIMARY_BUS or PCI_SECONDARY_BUS registers on this
PCI Bridge, correctly update driver's first_busno and sec_busno
variables, so that pcie_advk_addr_valid() function can check if address
of any device behind the root bus is valid and that PIO transfers are
started with correct config type (1 vs 0), which is required for
accessing devices behind some PCI bridge after the root bus.
U-Boot's PCI_PNP code sets primary and secondary bus numbers as relative
to the configured bus number of the root bus. This is done so that
U-Boot can support multiple PCIe host bridges or multiple root port
buses, when internal bus numbers are different.
Now that root bus is available, update code in pcie_advk_read_config()
and pcie_advk_write_config() functions to correctly calculate real
Aardvark bus number of the target device from U-Boot's bus number as:
busno = PCI_BUS(bdf) - dev_seq(bus)
Stefan: Small fix of header masking as suggested by Pali.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Aardvark reports Disabled and Hot Reset LTSSM states as values >= 0x20.
Link is not up in these states, so fix pcie_advk_link_up() function.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Subroutines in comphy_usb2_power_up() and comphy_sgmii_power_up() functions
may fail. In this case, do not continue execution of current function and
instead jump to the end. Return value in 'ret' variable is already set.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
phy_txd_inv or phy_rxd_inv needs to be set only in case when
appropriate polarity is inverted. Otherwise these bits should be
cleared.
Same change was included in TF-A project:
https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/9406
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Marvell Armada 3700 Functional Specifications, section 52.2 PCIe Link
Initialization says that TXDCLK_2X_SEL bit needs to be enabled for PCIe
Root Complex mode.
Same change was included in TF-A project:
https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/9408
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the CONFIG_STM32_FLASH to Kconfig by using
tools/moveconfig.py
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add protection on presence and order of the phy node sub node
by using the mandatory reg information.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
