In function nand_write_skip_bad(),for YAFFS filesystem part,
write_oob() will return 0 when success, so when rval equals 0,
it should continue to write the next page, and no break.
Signed-off-by: Wentao, Liu <wentao.liu@intel.com>
Acked-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Scott Wood <scott@tyr.buserror.net>
This fixes the issue where mxs_dma_init() was called either twice or never,
without introducing any new init hooks.
The idea is to allow each and every device using the APBH DMA block to
configure and request only the channels it uses, instead of making it call init
for all the channels as is now.
The common DMA block init part, which only configures the block, is then called
from CPUs arch_cpu_init() call.
NOTE: This patch depends on:
http://patchwork.ozlabs.org/patch/150957/
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
The following warnings are reported for boards using SOFT ECC.
omap_gpmc.c:33:30: warning: 'hw_nand_oob' defined but not used
omap_gpmc.c:78:13: warning: 'omap_hwecc_init' defined but not used
omap_gpmc.c:116:12: warning: 'omap_correct_data' defined but not used
omap_gpmc.c:182:12: warning: 'omap_calculate_ecc' defined but not used
omap_gpmc.c:208:13: warning: 'omap_enable_hwecc' defined but not used
Signed-off-by: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Scott Wood <scottwood@freescale.com>
Freescale IFC NAND Machine calculates ECC on 512byte sector and same is used in
fsl_ifc_run_command() during ECC status verification. Also this sector is passed
to is_blank() for blank checking. It is wrong at first place because
is_blank()'s implementation checks for Page size and OOB area size.
is_blank() should be called per page for main and OOB area verification.
Variables name are redefined to avoid confusion between buffer and ecc sector.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
1) OOB area should be updated irrespective of NAND page size. Earlier it was
updated only for 512byte NAND page.
2) During OOB update fbcr should be equal to OOB size.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
commit 2a8e0fc8b3 ("nand: Merge changes
from Linux nand driver") accidentally reverted commit
13f0fd94e3 ("NAND: Scan bad blocks
lazily.").
Reinstate the change, as amended by commit
ff49ea8977 ("NAND: Mark the BBT as scanned
prior to calling scan_bbt.").
Signed-off-by: Scott Wood <scottwood@freescale.com>
This reverts commit 4fee6c2f29.
It breaks boards that currently rely on soft-ecc, as pointed out here:
http://patchwork.ozlabs.org/patch/140872/
The reverted patch should be resubmitted with documentation, and with the
CONFIG_MTD_ECC_SOFT selected from every board that needs it. We could
start by looking at what NAND driver the board selects, and whether
that driver ever asks for soft ECC.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This driver doesn't yet make use of the added flexibility (not that that
should stop anyone from converting...), but it will with the in-progress
hack to support 4k-page NAND.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This allows a driver to run code between nand_scan_ident() and
nand_scan_tail(), among other things. See the additions to
doc/README.nand for details.
To allow a gradual transition, Boards that don't set
CONFIG_SYS_NAND_SELF_INIT will still be initialized the old way, but
new drivers should not require this, and existing drivers should be
converted when convenient.
Signed-off-by: Scott Wood <scottwood@freescale.com>
- fix NAND_CMD_READID command for ONFI detect.
- add NAND_CMD_PARAM command to read the ONFI parameter page.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The software ECC algorithm is not necessary when hardware ECC
is available and can be left out for a smaller image size.
Enable with CONFIG_MTD_ECC_SOFT.
Signed-off-by: Christian Hitz <christian.hitz@aizo.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
[backport from linux commit 02f8c6aee8df3cdc935e9bdd4f2d020306035dbe]
This is part of the synchronization with the nand driver to the
Linux 3.0 state.
Signed-off-by: Christian Hitz <christian.hitz@aizo.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
[backport from linux commit 02f8c6aee8df3cdc935e9bdd4f2d020306035dbe]
This patch synchronizes the nand driver with the Linux 3.0 state.
Signed-off-by: Christian Hitz <christian.hitz@aizo.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
[backport from linux commit 02f8c6aee8df3cdc935e9bdd4f2d020306035dbe]
This patch synchronizes the nand driver with the Linux 3.0 state.
Signed-off-by: Christian Hitz <christian.hitz@aizo.com>
Cc: Scott Wood <scottwood@freescale.com>
[scottwood@freescale.com: minor fixes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Bring up to date with corresponding file from linux.
Signed-off-by: Christian Hitz <christian.hitz@aizo.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
[backport from linux commit 02f8c6aee8df3cdc935e9bdd4f2d020306035dbe]
This patch merges the additional NAND flash types from the 3.0 Linux
kernel.
Signed-off-by: Christian Hitz <christian.hitz@aizo.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
[backport from linux commit 02f8c6aee8df3cdc935e9bdd4f2d020306035dbe]
This patch merges the BCH ECC algorithm from the 3.0 Linux kernel.
This enables U-Boot to support modern NAND flash chips that
require more than 1-bit of ECC in software.
Signed-off-by: Christian Hitz <christian.hitz@aizo.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Currently nand_spl_simple puts it's temp data at 0x10000 offset in SDRAM
which is likely to contain already loaded data.
The patch saves the oob data and the ecc on the stack replacing
the fixed address in RAM.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Ilya Yanok <yanok@emcraft.com>
CC: Scott Wood <scottwood@freescale.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Simon Schwarz <simonschwarzcor@googlemail.com>
CC: Wolfgang Denk <wd@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Fix:
nand_spl_load.c: In function 'nand_boot':
nand_spl_load.c:31:6: warning: variable 'ret' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Fix warnings for both cases:
definded CONFIG_SYS_NAND_HW_ECC_OOBFIRST:
nand_spl_simple.c: In function 'nand_read_page':
nand_spl_simple.c:156:6: warning: variable 'stat' set but not used
[-Wunused-but-set-variable]
not definded CONFIG_SYS_NAND_HW_ECC_OOBFIRST:
nand_spl_simple.c: In function 'nand_read_page':
nand_spl_simple.c:196:6: warning: variable 'stat' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Use software ECC for the SPL build if support for software ECC in SPL is
enabled.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Scott Wood <scottwood@freescale.com>
This patch adds support for software ECC to the nand_spl_simple driver.
To enable this one have to define CONFIG_SPL_NAND_SOFTECC.
Tested on OMAP3.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Scott Wood <scottwood@freescale.com>
s3c64xx.c implemented its own nand_read_byte, nand_write_buf and
nand_read_buf functions. This provoked a regression when these functions
were made public by patch 55f429bb39614a16b1bacc9a8bea9ac01a60bfc8.
This deletes these duplicated functions from s3c64xx.c and adds the generic
implementations in nand_base.c to the spl Makefile. It also adds
-ffcuntion-sections and -gc-sections to the compilation flags of the SPL to
avoid errors originating from unused functions in nand_base.c.
Description of the regression:
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/108873
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Cc: scottwood@freescale.com
Cc: s-paulraj@ti.com
Cc: albert.u.boot@aribaud.net
Functions often used in SPL are now part of linux/mtd/nand.h.
Static modifiers are removed from these functions in
drivers/mtd/nand/nand_base.c.
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Cc: scottwood@freescale.com
Cc: s-paulraj@ti.com
Cc: albert.u.boot@aribaud.net
Acked-by: Scott Wood <scottwood@freescale.com>
Change my old email address which is no longer valid.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
similiar to commit dc7cd8e59b, only
adapted for the new spl framework.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The debugX() macro was always used with debug level 1. There is no point to use
it here instead of debug().
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Jz4740 NAND flash controller can support:
* MLC NAND as well as SLC NAND
* all 8-bit/16-bit NAND flash devices
* HAMMING and RS hardware ECC
* automatic boot up from NAND flash devices
nand_ecclayout is set up for 2GiB NAND chip mounted in Qi LB60.
We'll bring up boot-from-NAND support in nand_spl/ in the future.
Signed-off-by: Xiangfu Liu <xiangfu@openmobilefree.net>
Acked-by: Daniel <zpxu@ingenic.cn>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
In nand_davinci_readecc(), select the correct NANDF<n>ECC register based
on CONFIG_SYS_NAND_CS rather than hardcoding the choice of NANDF1ECC.
This allows 1-bit hardware ECC to work with chip select other than CS2.
Note this now matches the usage in nand_davinci_enable_hwecc(), which
already had the correct handling, and allows refactoring to a single
function encapsulating the register read.
Without this fix, writing NAND pages to a chip not wired to CS2 would
result in in the ECC calculation always returning FFFFFF for each
512-byte segment, and reading back a correctly written page (one with
ECC intact) would always fail. With this fix, the ECC is written and
verified correctly.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
* 'master' of git://git.denx.de/u-boot-nand-flash:
PPC: Fix socrates NAND problem
PPC: Fix fsl_upm.c by renaming nand handling functions
NAND: Make page, erase, oob size available via cmd_nand
mtd: eLBC NAND: remove elbc_fcm_ctrl->oob_poi
NAND: Add -y option to nand scrub command
NAND: Add nand read.raw and write.raw commands
NAND: Really ignore bad blocks when scrubbing
spl, nand: add 4bit HW ecc oob first nand_read_page function
mxc_nand: fix a problem writing more than 32MB
mxc_nand: fixed some typos (cosmetic)
nand: increase chip_delay in mv kirkwood nand driver
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/p3060: Add SoC related support for P3060 platform
powerpc/85xx: Add support for setting up RAID engine liodns on P5020
powerpc/85xx: Refactor some defines out of corenet_ds.h
fm-eth: Add ability for board code to disable a port
powerpc/mpc8548: Add workaround for erratum NMG_LBC103
powerpc/mpc8548: Add workaround for erratum NMG_DDR120
powerpc/mpc85xxcds: Fix PCI speed
powerpc/mpc8548cds: Fix booting message
powerpc/p4080: Add support for secure boot flow
powerpc/85xx: Add Secure Boot support on P1010RDB for NOR, NAND & SPIFLASH
powerpc/85xx: Add PBL & SECUREBOOT support on P3041/P5020DS boards
powerpc/p2041rdb: remove watch dog related codes
powerpc/p2041rdb: updated description of cpld command
powerpc/p2041rdb: add more ddr frequencies support
powerpc/p2041rdb: set sysclk according to status of physical switch SW1
powerpc/p2041rdb: update cpld reset command according to CPLD 2.0
powerpc/mpc8349emds: Migrate from spd_sdram to unified DDR driver
powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver
powerpc/mpc8xxx: Add DDR2 to unified DDR driver
powerpc/mpc8xxx: Fix picos_to_mclk() and get_memory_clk_period_ps()
powerpc/mpc8xxx: Add SPD EEPROM address for single controller 2 slots
powerpc/mpc8xxx: Fix DDR code for empty first DIMM slot and enable DQS_en
powerpc/85xx: Refactor P2041RDB to use common p_corenet files
powerpc/85xx: refactor common P-Series CoreNet files for FSL boards
powerpc/85xx: Enable CMD_REGINFO on corenet boards
powerpc/85xx: p2041rdb - Remove unused 'execute' perm in TLB entries
powerpc/85xx: Fix USB protocol definitions for P1020RDB
powerpc/corenet_ds: Use separated speed tables for UDIMM and RDIMM
powerpc/mpc8xxx: Move DDR RCW overriding to common code
powerpc/mpc8xxx: Extend CWL table
powerpc/85xx: Cleanup how SVR_MAJ() is defined on MPC8536
powerpc/85xx: Cleanup extern in corenet_ds board code
powerpc/p2041rdb: Add ethernet support on P2041RDB board
powerpc/85xx: Add networking support to P1023RDS
powerpc/hydra: Add ethernet support on P5020/P3041 DS boards
powerpc/85xx: Add FMan ethernet support to P4080DS
powerpc/85xx: Add support for FMan ethernet in Independent mode
powerpc/mpc8548cds: Cleanup mpc8548cds.c
powerpc/mp: add support for discontiguous cores
powerpc/85xx: corenet_ds - Remove unused 'execute' perm in TLB entries
fdt: Add new fdt_create_phandle helper
fdt: Rename fdt_create_phandle to fdt_set_phandle
powerpc/85xx: Fix compile warnings/errors if CONFIG_SYS_DPAA_FMAN isn't set
fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010)
powerpc/P1010: Add workaround for erratum P1010-A003549 (related to IFC)
fsl_ifc: Add the workaround for erratum IFC-A002769 (enable on P1010)
powerpc/85xx: Expanding the window of CCSRBAR in AS=1 from 4k to 1M
powerpc/85xx: Add NAND/NAND_SPL support to P1010RDB
nand: Freescale Integrated Flash Controller NAND support
powerpc/85xx: Add basic support for P1010RDB
powerpc/85xx: Add support for new P102x/P2020 RDB style boards
powerpc/85xx: relocate CCSR before creating the initial RAM area
powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros
powerpc/85xx: Enable internal USB UTMI PHY on p204x/p3041/p50x0
powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014
This avoids colision with nand subsystem's functions.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The eLBC NAND driver currently follows up each program/write operation with a
read-back of the page, in order to [ostensibly] fill in ECC data for the
caller. However, the page address used for this read is always -1, so the read
will never work correctly. Remove this useless (and potentially problematic)
block of code.
v2: fix broken mailer
Signed-off-by: mhench <mhench@elutions.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
[scottwood@freescale.com: use chip instead of redundant priv_nand]
Signed-off-by: Scott Wood <scottwood@freescale.com>
When writing 0x4000 to the unlockend_blkaddr register, large writes to
a 2k page NAND sometimes fail. The current kernel driver writes 0xFFFF
to this register for V2 of the nand controller.
However on an i.MX31 this also fixes writes larger than 32MB.
The datasheet is very unspecific, but (0x4000=16384)*2000
roughly fits the limits we're encountering with NAND writes.
This problem might be NAND chip specific.
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The new SAMSUNG NAND Flash K9F1G08U0D require a bigger chip_delay.
The Data Transfer from Cell to Register is >= 35us. Other Vendors
and older chips normally use >= 25us. To have enough margin 40us
is selected.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Stefan Roese <sr@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
nand_bbt.c: In function ‘search_bbt’:
nand_bbt.c:465:6: warning: variable ‘bits’ set but not used
[-Wunused-but-set-variable]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Add NAND support (including spl) on IFC, such as is found on the p1010.
Note that using hardware ECC on IFC with small-page NAND (which is what
comes on the p1010rdb reference board) means there will be insufficient
OOB space for JFFS2, since IFC does not support 1-bit ECC. UBI should
work, as it does not use OOB for anything but ECC.
When hardware ECC is not enabled in CSOR, software ECC is now used.
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
[scottwood@freescale.com: ECC rework and misc fixes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch adds support for 16 bit NAND devices attached to the
NDFC on ppc4xx processors. Two config entries were added:
CONFIG_SYS_NDFC_16 - Setting this tells the NDFC that a
16 bit device is attached.
CONFIG_SYS_NDFC_EBC0_CFG - This is for the External Bus
Controller configuration register.
Also, a new ndfc_read_byte() function was added which does not
first convert the data to little endian.
The NAND SPL was also modified to do 16bit bad block testing
when a 16 bit chip is being used.
Signed-off-by: Alex Waterman <awaterman@dawning.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add a flag to nand_read_skip_bad() such that if true, any trailing
pages in an eraseblock whose contents are entirely 0xff will be
dropped.
The implementation is via a new drop_ffs() function which is
based on the function of the same name from the ubiformat
utility by Artem Bityutskiy.
This is as-per the reccomendations of the UBI FAQ [1]
[1] http://www.linux-mtd.infradead.org/doc/ubi.html#L_flasher_algo
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Artem Bityutskiy <dedekind1@gmail.com>
Acked-by: Detlev Zundel <dzu@denx.de>
CC: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
When specified in the flags argument of nand_write, WITH_YAFFS_OOB causes an
operation which is mutually exclusive with the 'usual' way of writing.
Add a check that client code does not specify WITH_YAFFS_OOB along with any
other flags and add a comment indicating that the WITH_YAFFS_OOB flag should
not be mixed with other flags.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
In a future commit the behaviour of nand_write_skip_bad()
will be further extended.
Convert the only flag currently passed to the nand_write_
skip_bad() function to a bitfield of only one allocated
member. This should avoid an explosion of int's at the
end of the parameter list or the ambiguous calls like
nand_write_skip_bad(info, offset, len, buf, 0, 1, 1);
nand_write_skip_bad(info, offset, len, buf, 0, 1, 0);
Instead there will be:
nand_write_skip_bad(info, offset, len, buf, WITH_YAFFS_OOB |
WITH_OTHER);
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Replace an incorrect 'read' with 'write' in a comment.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch sync with Brian's patch on Linux in nand_flash_detect_onfi()
commit b7b1a29d94c17e4341856381bccb4d17495bea60
Author: Brian Norris <computersforpeace@gmail.com>
Date: Sun Dec 12 00:23:33 2010 -0800
mtd: nand: rearrange ONFI revision checking, add ONFI 2.3
In checking for the ONFI revision, the first conditional (for checking
"unsupported" ONFI) seems unnecessary. All ONFI revisions should be
backwards-compatible; even if this is not the case on some newer ONFI
revision, it should simply fail the second version-checking if-else block
(i.e., the bit-fields for 1.0, 2.0, etc. would not be set to 1). Thus, we
move our "unsupported" condition after having checked each bit field.
Also, it's simple enough to add a condition for ONFI revision 2.3. Note
that this does *NOT* mean we handle all new features of ONFI versions
above 1.0.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
This patch sync with David's patch on Linux in nand_flash_detect_onfi()
commit 4ccb3b4497ce01fab4933704fe21581e30fda1a5
Author: David Woodhouse <David.Woodhouse@intel.com>
Date: Fri Dec 3 16:36:34 2010 +0000
mtd: nand: Fix integer overflow in ONFI detection of chips >= 4GiB
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
If NCE is hooked up to NCS3, we don't need to (and can't)
explicitly set the state of the NCE pin. Instead, the
controller asserts it automatically as part of a
command/data access. Only "CE don't care"-type NAND chips
can be used in this manner.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Reinhard Meyer <u-boot@emk-elektronik.de>
This patch adds support for reading an ONFI page parameter from a NAND
device supporting it. If this is the case, struct nand_chip onfi_version
member contains the supported ONFI version, 0 otherwise.
This allows NAND drivers past nand_scan_ident to set the best timings for the
NAND chip.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch sync with David's patch on Linux for handling nand_scan_ident.
commit 5e81e88a4c140586d9212999cea683bcd66a15c6
Author: David Woodhouse <David.Woodhouse@intel.com>
Date: Fri Feb 26 18:32:56 2010 +0000
mtd: nand: Allow caller to pass alternative ID table to nand_scan_ident()
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Lei Wen <leiwen@marvell.com>
This patch add addition suffix to nand write to give the uboot
the power to directly burn the yaffs image to nand.
Signed-off-by: Lei Wen <leiwen@marvell.com>
This is part of the timer cleanup effort.
In the future we only use get_timer() in its intended way to
program timeout loops.
reset_timer() shall not be used anymore.
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
According to Freescale reference manuals (eg section "13.4.4.2
Programming the UPMs" of the P4080 Reference Manual):
"Since the result of any update to the MxMR/MDR register must be in
effect before the dummy read or write to the UPM region, a write to
MxMR/MDR should be followed immediately by a read of MxMR/MDR."
The UPM on a custom P4080-based board did not work without performing
a read of MxMR/MDR after a write.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The attached patch fixes wrong timing default values and adds the
possibility to specify board specific timing value in the board config file.
Signed-off-by: David Mueller <d.mueller@elsoft.ch>
This is needed for the canyonlands_nand build target. Without it
the resulting image won't fit into 4k.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
By now, the majority of architectures have working relocation
support, so the few remaining architectures have become exceptions.
To make this more obvious, we make working relocation now the default
case, and flag the remaining cases with CONFIG_NEEDS_MANUAL_RELOC.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
This patch adds generic support for the Samsung s3c2440 processor.
Global s3c24x0 changes to struct members converting from upper case to
lower case.
Signed-off-by: Craig Nauman <cnauman@diagraph.com>
Cc: kevin.morfitt@fearnside-systems.co.uk
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The ECC calculations were started by writing 1 << 13 to the nand FCR register;
that value is also defined as DAVINCI_NANDFCR_4BIT_CALC_START in emif_defs.h.
This patch substitutes the macro DAVINCI_NANDFCR_4BIT_CALC_START for the
magic number '1 << 13'.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Get rid of the several "#if 0" sections that were keeping around Linux
code that isn't relevant to U-Boot. Besides cluttering the code, these
sections make tracking upstream changes harder, rather than easier.
It's easy to discard obviously irrelevant diff hunks that patch rejects,
but it's not as easy to notice hunks that apply cleanly to the #if 0
section, but *are* relevant to U-Boot and require modification elsewhere.
Also remove suspend/resume, as this is not applicable to U-Boot. Removal
saves 232 bytes on powerpc.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
A while back, in http://lists.denx.de/pipermail/u-boot/2009-June/054428.html,
Michele De Candia posted a patch to not count bad blocks toward the
requested size to be erased. This is desireable when you're passing in
something like $filesize, but not when you're trying to erase a partition.
Thus, a .spread subcommand (named for consistency with
http://lists.denx.de/pipermail/u-boot/2010-August/075163.html) is introduced
to make explicit the user's desire to erase for a given amount of data,
rather than to erase a specific region of the chip.
While passing $filesize to "nand erase" is useful, accidentally passing
something like $fliesize currently produces quite unpleasant results, as the
variable evaluates to nothing and U-Boot assumes that you want to erase
the entire rest of the chip/partition. To improve the safety of the
erase command, require the user to make explicit their intentions by
using a .part or .chip subcommand. This is an incompatible user interface
change, but keeping compatibility would eliminate the safety gain, and IMHO
it's worth it.
While touching nand_erase_opts(), make it accept 64-bit offsets and sizes,
fix the percentage display when erase length is rounded up, eliminate
an inconsistent warning about rounding up the erase length which only
happened when the length was less than one block (rounding up for $filesize
is normal operation), and add a diagnostic if there's an attempt to erase
beginning at a non-block boundary.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
The underlying code in nand_base.c already supports non-page-aligned reads
and writes, but the block-skipping wrapper code did not.
With block skipping, an unaligned start address is not useful since you
really want to be starting at the beginning of a partition -- or at least
that's where you want to start checking for blocks to skip, but we don't
(yet) support that. So we still require the start address to be aligned.
An unaligned length, though, is useful for passing $filesize to the
read/write command, and handling it does not complicate block skipping.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
This patch moves some ppc4xx related headers from the common include
directory (include/) to the powerpc specific one
(arch/powerpc/include/asm/). This way to common include directory is not
so cluttered with files.
Signed-off-by: Stefan Roese <sr@denx.de>
Due to a register glitch (result code <4 might show up right after the
start-calculation-bit was set), make sure the ECC has really started.
See 1c3275b656045aff9a75bb2c9f3251af1043ebb3 in the kernel.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
This printk was added recently and results in ugly output on systems
with no NAND:
NAND: nand_get_flash_type: unknown NAND device: Manufacturer ID: 0x00, Chip ID: 0x00 0 MiB
instead of:
NAND: 0 MiB
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Currently, 83xx, 86xx, and 85xx have a lot of duplicated code
dedicated to defining and manipulating the LBC registers. Merge
this into a single spot.
To do this, we have to decide on a common name for the data structure
that holds the lbc registers - it will now be known as fsl_lbc_t, and we
adopt a common name for the immap layouts that include the lbc - this was
previously known as either im_lbc or lbus; use the former.
In addition, create accessors for the BR/OR regs that use in/out_be32
and use those instead of the mismash of access methods currently in play.
I have done a successful ppc build all and tested a board or two from
each processor family.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rather than bang MMRs directly, use the new portmux framework to handle
the details.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Scott Wood <scottwood@freescale.com>
Make it easy to use GPIOs for the DEV_READY pin by using the common GPIO
framework. Also make the NAND_PLAT_INIT() define optional.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
The Toshiba TC58NVG0* parts are 128Mbytes x 8 bits 3.3V parts with the 0xD1
identifier. Add these to the list of known devices IDs.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
When the NAND part is not supported, it is useful to show the manufacturer
and device ID to help debugging and reporting.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The current Blackfin nand write function fills up the write buffer but
returns before it has had a chance to drain. On faster systems, this
isn't a problem as the operation finishes before the ECC registers are
read, but on slower systems the ECC may be incomplete when the core tries
to read it.
So wait for the buffer to drain once we're done writing to it.
Signed-off-by: Andrew Caldwell <Andrew.Caldwell@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This is a patch to use the hardware ECC controller of
the AT91SAM9260 for the AT91 nand. Taken from the kernel 2.6.33.
Signed-off-by: Nikolay Petukhov <Nikolay.Petukhov@gmail.com>
I executed 'find . -name "*.[chS]" -perm 755 -exec chmod 644 {} \;'
Signed-off-by: Thomas Weber <swirl@gmx.li>
Add some more: neither Makefile nor config.mk need execute permissions.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Add support for version 1.1 of the nfc nand flash
controller which is on the i.mx25 soc.
Signed-off-by: John Rigby <jcrigby@gmail.com>
CC: Scott Wood <scottwood@freescale.com>
SPEAr SoCs contain an FSMC controller which can be used to interface
with a range of memories eg. NAND, SRAM, NOR.
Currently, this driver supports interfacing FSMC with NAND memories
Signed-off-by: Vipin <vipin.kumar@st.com>
Import the large page oob layout from Linux mxc_nand.c driver.
The CONFIG_SYS_NAND_LARGEPAGE option is used to activate
the large page oob layout. Run time detection is not supported
as this moment.
This has been tested on the i.MX31 PDK board with a large
page NAND device.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Introduces various optimisations that approximately triple the
read data rate from NAND when run on da830evm.
Most of these optimisations depend on the endianess of the machine
and most of them are very similar to optimisations already present
in the Linux Kernel.
Signed-off-by: Nick Thompson <nick.thompson@ge.com>
Davinci: NAND enable ECC even when not in NAND boot mode
On Davinci platforms, the default NAND device is enabled (for ECC)
in low level boot code when NAND boot mode is used. If booting in
another mode, NAND ECC is not enabled. The driver should make
sure ECC is enabled regardless of boot mode if NAND is configured
in U-Boot.
Signed-off-by: Nick Thompson <nick.thompson@ge.com>
Davinci: Configurable NAND chip selects
Add a CONFIG_SYS_NAND_CS setting to all davinci configs and
use it to setup the NAND controller in the davinci_nand
mtd driver.
Signed-off-by: Nick Thompson <nick.thompson@gefanuc.com>
Currently, the last block of NAND devices can't be accessed. This patch
fixes this issue by correcting the boundary checking (off-by-one error).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
There is more and more usage of printing 64bit values,
so enable this feature generally, and delete the
CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
defines.
Signed-off-by: Heiko Schocher <hs@denx.de>
Depending on offset, flash size and the number of bad blocks,
get_len_incl_bad may return a too small value which may lead to:
1) If there are no bad blocks, nand_{read,write}_skip_bad chooses the
bad block aware read/write code. This may hurt performance, but does
not have any adverse effects.
2) If there are bad blocks, the nand_{read,write}_skip_bad may choose
the bad block unaware read/write code (if len_incl_bad == *length)
which leads to corrupted data.
Signed-off-by: Daniel Hobi <daniel.hobi@schmid-telecom.ch>
This patch adds a unified s3c24x0 cpu header file that selects the header
file for the specific s3c24x0 cpu from the SOC and CPU configs defined in
board config file. This removes the current chain of s3c24-type #ifdef's
from the s3c24x0 code.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch moves the s3c24x0 header files from include/ to
include/asm-arm/arch-s3c24x0/.
checkpatch.pl showed 2 errors and 3 warnings. The 2 errors were both due
to a non-UTF8 character in David M?ller's name:
ERROR: Invalid UTF-8, patch and commit message should be encoded in UTF-8
#489: FILE: include/asm-arm/arch-s3c24x0/s3c2410.h:3:
+ * David M?ller ELSOFT AG Switzerland. d.mueller@elsoft.ch
As David's name correctly contains a non-UTF8 character I haven't fixed
these errors.
The 3 warnings were all because of the use of 'volatile' in s3c24x0.h:
WARNING: Use of volatile is usually wrong: see Documentation/volatile-considered-harmful.txt
#673: FILE: include/asm-arm/arch-s3c24x0/s3c24x0.h:35:
+typedef volatile u8 S3C24X0_REG8;
+typedef volatile u16 S3C24X0_REG16;
+typedef volatile u32 S3C24X0_REG32;
I'll fix these errors in another patch.
Tested by running MAKEALL for ARM8 targets and ensuring there were no new
errors or warnings.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds support for NAND devices with a page size of
4K in the DaVinci NAND driver. The layout matches the layout that TI uses
for 4K page size NAND devices in the kernel NAND driver.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch add nand_read_buf() for S3C2410 NAND SPL.
In nand_spl/nand_boot.c, nand_boot() will check nand->select_chip,
so nand->select_chip should also be initialized.
Signed-off-by: Hui.Tang <zetalabs@gmail.com>
This patch updates a check condition in the NAND driver.
The check condition is similat to what is in linux/next.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The commit 66372fe2 manually relocated the bbt pattern pointer,
which can be removed by using full relocation.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
The syndrome based page read/write routines store ECC, and possibly other
"OOB" data, right after each chunk of ECC'd data. With ECC chunk size of
512 bytes and a large page (2KiB) NAND, the layout is:
data-0 OOB-0 data-1 OOB-1 data-2 OOB-2 data-3 OOB-3 OOB-leftover
Where OOBx is (prepad, ECC, postpad). However, the current "raw" routines
use a traditional layout -- data OOB, disregarding the prepad and postpad
values -- so when they're used with that type of ECC hardware, those calls
mix up the data and OOB. Which means, in particular, that bad block
tables won't be found on startup, with data corruption and related chaos
ensuing.
The current syndrome-based drivers in mainline all seem to use one chunk
per page; presumably they haven't noticed such bugs.
Fix this, by adding read/write page_raw_syndrome() routines as siblings of
the existing non-raw routines; "raw" just means to bypass the ECC
computations, not change data and OOB layout.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When computing oobavail from the list of free areas in the OOB,
don't assume there will always be an unused slot at the end.
This syncs up with the kernel NAND driver.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The patch updates the check condition for determining
whether the ECC corrections has failed.
This makes it similar to what is in the kernel NAND driver.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This was originally part of Thomas Gleixner's patch for
adding support for 4KiB pages.
This is not part of the U-Boot NAND driver so updating the
driver with this to sync up with the kernel NAND driver.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch updates the "chip_shift" calculation in the
NAND driver. This is being done to sync up the NAND driver with
the kernel NAND driver.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds support for NANDs greater than 2 GB.
Patch is based on the MTD NAND driver in the kernel.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch re-formats the arm920t s3c24x0 nand driver in preparation for changes
to add support for the Embest SBC2440-II Board.
The changes are as follows:
- re-indent the code using Lindent
- make sure register layouts are defined using a C struct
- replace the upper-case typedef'ed C struct names with lower case
non-typedef'ed ones
- make sure registers are accessed using the proper accessor functions
- run checkpatch.pl and fix any error reports
It assumes the following patch has been applied first:
- [U-Boot][PATCH-ARM] CONFIG_SYS_HZ fix for ARM902T S3C24X0 Boards, 05/09/2009
- patches 1/4, 2/4 and 3/4 of this series
Tested on an Embest SBC2440-II Board with local u-boot patches as I don't have
any s3c2400 or s3c2410 boards but need this patch applying before I can submit
patches for the SBC2440-II Board. Also, temporarily modified sbc2410x, smdk2400,
smdk2410 and trab configs to use the mtd nand driver (which isn't used by any
board at the moment), ran MAKEALL for all ARM9 targets and no new warnings or
errors were found.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add #ifdefs where necessary to not perform relocation fixups. This
allows boards/architectures which support relocation to trim a decent
chunk of code.
Note that this patch doesn't add #ifdefs to architecture-specific code
which does not support relocation.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
I accidentally left v2 of "NAND: DaVinci:Adding 4 BIT ECC support"
applied when I pushed the tree last merge window, and missed these fixes
which were in v3 of that patch.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch cleans up multiple issues of the 4xx register (mostly
DCR, SDR, CPR, etc) definitions:
- Change lower case defines to upper case (plb4_acr -> PLB4_ACR)
- Change the defines to better match the names from the
user's manuals (e.g. cprpllc -> CPR0_PLLC)
- Removal of some unused defines
Please test this patch intensive on your PPC4xx platform. Even though
I tried not to break anything and tested successfully on multiple
4xx AMCC platforms, testing on custom platforms is recommended.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds 4 BIT ECC support in the DaVinci NAND
driver. Tested on both the DM355 and DM365.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch adds the new mode NAND_ECC_HW_OOB_FIRST in the nand code to
support 4-bit ECC on TI DaVinci devices with large page (up to 2K) NAND
chips. This ECC mode is similar to NAND_ECC_HW, with the exception of
read_page API that first reads the OOB area, reads the data in chunks,
feeds the ECC from OOB area to the ECC hw engine and perform any
correction on the data as per the ECC status reported by the engine.
This patch has been accepted by Andrew Morton and can be found at
http://userweb.kernel.org/~akpm/mmotm/broken-out/mtd-nand-add-new-ecc-mode-ecc_hw_oob_first.patch
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Driver for NFC NAND controller found on Freescale's MX2 and MX3
processors. Ported from Linux. Tested only with i.MX27 but should
works with other MX2 and MX3 processors too.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch adds a new "page" parameter to all NAND read_page/read_page_raw
APIs. The read_page API for the new mode ECC_HW_OOB_FIRST requires the
page information to send the READOOB command and read the OOB area before
the data area.
This patch has been accepted by Andrew Morton and can be found at
http://userweb.kernel.org/~akpm/mmotm/broken-out/mtd-nand-add-page-parameter-to-all-read_page-read_page_raw-apis.patch
WE would like this to become part of the u-boot GIT as well
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Fix ECC Correction bug where the byte offset location were double
flipped causing correction routine to toggle the wrong byte location
in the ECC segment. The ndfc_calculate_ecc routine change the order
of getting the ECC code.
/* The NDFC uses Smart Media (SMC) bytes order */
ecc_code[0] = p[2];
ecc_code[1] = p[1];
ecc_code[2] = p[3];
But in the Correction algorithm when calculating the byte offset
location, the s1 is used as the upper part of the address. Which
again reverse the order making the final byte offset address
location incorrect.
byteoffs = (s1 << 0) & 0x80;
.
.
byteoffs |= (s0 >> 4) & 0x08;
The order is change to read it in straight and let the correction
function to revert it to SMC order.
Signed-off-by: Feng Kan <fkan@amcc.com>
Acked-by: Victor Gallardo <vgallardo@amcc.com>
Acked-by: Prodyut Hazarika <phazarika@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Embedd chip select configuration into struct for gpmc config
instead of having it completely separated as suggested by
Wolfgang Denk on
http://lists.denx.de/pipermail/u-boot/2009-May/052247.html
Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>
Legacy NAND had been scheduled for removal. Any boards that use this
were already not building in the previous release due to an #error.
The disk on chip code in common/cmd_doc.c relies on legacy NAND,
and it has also been removed. There is newer disk on chip code
in drivers/mtd/nand; someone with access to hardware and sufficient
time and motivation can try to get that working, but for now disk
on chip is not supported.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Now that the 4xx NAND driver ndfc is moved to the common NAND driver
directory we don't need this #ifdef's anymore.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch adds a NAND driver for the Marvell Kirkwood SoC's
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Scott Wood <scottwood@freescale.com>
The bbt descriptors contains the pointer to the bbt pattern which
are statically initialized memory struct. When relocated to RAM,
these pointers will continue point to NOR flash(or L2 SRAM, or
other boot device). If the contents of NOR flash changed or L2
SRAM disabled, it'll hang the system.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The S3C2410 NAND driver source file is included in the makefile instead of
the object file.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Scott Wood <scottwood@freescale.com>
nand_util currently uses size_t which is arch dependent and not always a
unsigned long. Now use loff_t, as does the linux mtd layer.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The BF537-STAMP Blackfin board had a driver for working with NAND devices
that are simply memory mapped. Since there is nothing Blackfin specific
about this, generalize the driver a bit so that everyone can leverage it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Update chipselect handling in davinci_nand.c so that it can
handle 2 GByte chips the same way Linux does: as one device,
even though it has two halves with independent chip selects.
For such chips the "nand info" command reports:
Device 0: 2x nand0, sector size 128 KiB
Switch to use the default chipselect function unless the board
really needs its own. The logic for the Sonata board moves out
of the driver into board-specific code. (Which doesn't affect
current build breakage if its NAND support is enabled...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Remove CONFIG_SYS_DAVINCI_BROKEN_ECC option. It's not just nasty;
it's also unused by any current boards, and doesn't even match the
main U-Boot distributions from TI (which use soft ECC, or 4-bit ECC
on newer chips that support it).
DaVinci GIT kernels since 2.6.24, and mainline Linux since 2.6.30,
match non-BROKEN code paths for 1-bit HW ECC. The BROKEN code paths
do seem to partially match what MontaVista/TI kernels (4.0/2.6.10,
and 5.0/2.6.18) do ... but only for small pages. Large page support
is really broken (and it's unclear just what software it was trying
to match!), and the ECC layout was making three more bytes available
for use by filesystem (or whatever) code.
Since this option itself seems broken, remove it. Add a comment
about the MV/TI compat issue, and the most straightforward way to
address it (should someone really need to solve it).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Minor cleanup for DaVinci NAND code:
- Use I/O addresses from nand_chip; CONFIG_SYS_NAND_BASE won't
be defined when there are multiple chipselect lines in use
(as with common 2 GByte chips).
- Cleanup handling of EMIF control registers
* Only need one pointer pointing to them
* Remove incorrect and unused struct supersetting them
- Use the standard waitfunc; we don't need a custom version
- Partial legacy cleanup:
* Don't initialize every board like it's a DM6446 EVM
* #ifdef a bit more code for BROKEN_ECC
Sanity checked with small page NAND on dm355 and dm6446 EVMs;
and large page on dm355 EVM (packaged as two devices, not one).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
NAND module should not modify EMIF registers unrelated to CS2
that is used for NAND, i.e. do not modify EWAIT config register
or registers for other Chip Selects.
Without this patch, EMIF configurations made in board_init()
will be invalidated.
Signed-off-by: Thomas Lange <thomas@corelatus.se>
This patch adds NAND Flash Controller driver for MPC5121 revision 2.
All device features, except hardware ECC and power management, are
supported.
This NFC driver replaces the one orignally posted by John Rigby:
"[PATCH] Freescale NFC NAND driver"
It's a port of the Linux driver version posted by Piotr Ziecik a few
weeks ago. Using this driver has the following advantages (from my
point of view):
- Compatibility with the Linux NAND driver (e.g. ECC usage)
- Better code quality in general
- Resulting U-Boot image is a bit smaller (approx. 3k)
- Better to sync with newer Linux driver versions
The only disadvantage I can see, is that HW-ECC is not supported right
now. But this could be added later (e.g. port from Linux driver after
it's supported there). Using HW-ECC on the MCP5121 NFC has a general
problem because of the ECC usage in the spare area. This collides with
JFFS2 for example.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Piotr Ziecik <kosmo@semihalf.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
This new define enables mtdcore.c compilation and with this we can
select the MTD device infrastructure needed for the reworked mtdparts
command.
We now have the 2 MTD infrastructure defines, CONFIG_MTD_DEVICE and
CONFIG_MTD_PARTITIONS. CONFIG_MTD_DEVICE is needed (as explained above)
for the "mtdparts" command and CONFIG_MTD_PARTITIONS is needed for UBI.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
This patch brings the U-Boot MTD infrastructure in sync with the current
Linux MTD version (2.6.30-rc3). Biggest change is the 64bit device size
support and a resync of the mtdpart.c file which has seen multiple fixes
meanwhile.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Kyungmin Park <kmpark@infradead.org>
This patch enables Smart Media (SMC) ECC byte ordering which is used
on the PPC4xx NAND FLASH controller (NDFC). Without this patch we have
incompatible ECC byte ordering to the Linux kernel NDFC driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
With this patch the NAND and OneNAND devices are registered in the MTD
subsystem and can then be referenced by the mtdcore code (e.g.
get_mtd_device_nm()). This is needed for the new "ubi part" command
syntax without the flash type parameter (nor|nand|onenand).
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes this compilation warning when CONFIG_MTD_PARTITIONS is
defined:
nand_base.c: In function 'nand_release':
nand_base.c:2922: warning: implicit declaration of function 'del_mtd_partitions'
Signed-off-by: Stefan Roese <sr@denx.de>
We need to make sure the data written to the nand flash controller makes
it there before we start polling its status register. Otherwise, we may
get stale data and return before the controller is actually ready.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Scott Wood <scottwood@freescale.com>
The NAND flash on the TQM8548_BE modules requires a short delay after
running the UPM pattern like the MPC8360ERDK board does. The TQM8548_BE
requires a further short delay after writing out a buffer. Normally the
R/B pin should be checked, but it's not connected on the TQM8548_BE.
The corresponding Linux FSL UPM driver uses similar delay points at the
same locations. To manage these extra delays in a more general way, I
introduced the "wait_flags" field allowing the board-specific driver to
specify various types of extra delay.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
For the NAND chips on the TQM8548 modules, a special chip-select logic is
used. It uses dedicated address lines to be set via UPM machine address
register (mar). This patch adds such support to the FSL-UPM driver.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch adds support for multi-chip NAND devices to the FSL-UPM
driver. The "dev_ready" callback of the "struct fsl_upm_nand" is now
called with the argument "chip_nr" to allow testing the proper chip
select line. The NAND support of the MPC8360ERDK is updated as well.
No other boards are currently using the FSL UPM driver.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch adds support for NAND_MAX_CHIPS to the MTD NAND layer.
Multi-chips devices are displayed as shown:
Device 0: 2x NAND 512MiB 3,3V 8-bit, sector size 128 KiB
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This driver implements the ECC algorithm described in
the CPU data sheet and uses the OOB layout chosen in
already-released development systems (shipped with a custom-made
u-boot 1.3.1).
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
Without the timeout present an infinite loop can occur if the
NAND device is broken or not present.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Commit cfa460adfd removed support
for disabling the "No NAND device found!!!" warning when
CONFIG_SYS_NAND_QUIET_TEST was defined. This re-adds support
for silencing the warning.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Dear Wolfgang,
You are right, the patch was ugly.
The new one seems to be better.
Signed-off-by: Valeriy Glushkov <gvv@lstec.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch renames NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPS and
changes the default from 8 to 1 for the legacy and the new MTD
NAND layer. This allows to remove all NAND_MAX_CHIPS definitions
in the board config files because none of the boards use multi
chip support (NAND_MAX_CHIPS > 1) so far. The bamboo and the DU440
define
#define NAND_MAX_CHIPS CONFIG_SYS_MAX_NAND_DEVICE
but that's bogus and did not work anyhow.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Enable nand lock, unlock and status of lock feature.
Not every device and platform requires this, hence,
it is under define for CONFIG_CMD_NAND_LOCK_UNLOCK
Nand unlock and status operate on block boundary instead
of page boundary. Details in:
http://www.micron.com/products/partdetail?part=MT29C2G24MAKLAJG-6%20IT
Intial solution provided by Vikram Pandita <vikram.pandita@ti.com>
Includes preliminary suggestions from Scott Wood
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Rather than putting the function prototype for board_nand_init() in the one
place where it gets called, put it into nand.h so that every place that also
defines it gets the prototype. Otherwise, errors can go silently unnoticed
such as using the wrong return value (void rather than int) when defining
the function.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The current code that determines which bank/chipselect is used for a
given NAND instance only worked for 32-bit addresses and assumed
a 1:1 mapping. This breaks in 36-bit physical configs.
The proper way to handle this is to use the virt_to_phys() and
BR_PHYS_ADDR() routinues to match the 34-bit lbc bus address
with the the virtual address the NAND code uses.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Scott Wood <scottwood@freescale.com>
Otherwise, recursion can occur if scan_bbt does not find a bad block
table, and tries to write one, and the attempt to erase the BBT area
causes a bad block check.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This caused the operation to be needlessly repeated if there were
no bad blocks and no errors.
Signed-off-by: Valeriy Glushkov <gvv@lstec.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
As reported by Ilko Iliev <iliev@ronetix.at>, the "nand erase clean"
command is currently broken, and among other things causes all blocks
to be marked bad.
This implements it properly using MTD_OOB_AUTO, along with some
indentation fixes.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Hardware expects ECCM 0 for small page and ECCM 1 for large page
when booting from NAND, so use those defaults.
Signed-off-by: Scott Wood <scottwood@freescale.com>
- Rename lbus83xx_t to fsl_lbus_t and move it to asm/fsl_lbc.h so that it
can be shared by both 83xx and 85xx
- Remove lbus83xx_t and replace it with fsl_lbus_t in all 83xx boards
files which use lbus83xx_t.
- Move FMR, FIR, FCR, FPAR, LTESR from mpc83xx.h to asm/fsl_lbc.h so that
85xx can share them.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Some chips require a RESET after power-up (e.g. Micron MT29FxGxxxxx).
The first command sent is NAND_CMD_READID.
Issue a NAND_CMD_RESET in nand_scan_ident before reading the device id.
Tested with an MT29F4G08AAC.
Signed-off-by: Karl Beldan <karl.beldan@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This brings the core NAND code up to date with the Linux kernel.
Since there were several drivers in Linux as of the last update that are
not in u-boot, I'm not bringing over new drivers that have been added
since in the absence of an interested party.
I did not update OneNAND since it was recently synced by Kyungmin Park,
and I'm not sure exactly what the common ancestor is.
Signed-off-by: Scott Wood <scottwood@freescale.com>
When the total size of all NAND devices exceeds 4 GiB, the size will
overflow. This patch tries to fix this.
Note that we still have a problem when a single NAND device is bigger
than 4 GiB: then the overflow would actually happen earlier, i. e.
when storing the size in nand_info[].size, as nand_info[].size is an
"u_int32_t".
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch deletes oobavail assignments, they're calculated by the nand
core code in nand_scan_tail, plus current oobavail values are wrong for
the LP NANDs.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch implements support for flash-based BBT for chips working
through ELBC NAND controller, so that NAND core will not have to re-scan
for bad blocks on every boot.
Because ELBC controller may provide HW-generated ECCs we should adjust
bbt pattern and bbt version positions in the OOB free area.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
For large page chips, nand_bbt is looking into OOB area, and checking
for "0xff 0xff" pattern at OOB offset 0. That is, two bytes should be
reserved for bbt means.
But ELBC driver is specifying ecclayout so that oobfree area starts at
offset 1, so only one byte left for the bbt purposes.
This causes problems with any OOB users, namely JFFS2: after first mount
JFFS2 will fill all OOBs with "erased marker", so OOBs will contain:
OOB Data: ff 19 85 20 03 00 ff ff ff 00 00 08 ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
And on the next boot, NAND core will rescan for bad blocks, then will
see "0xff 0x19" pattern, and will mark all blocks as bad ones.
To fix the issue we should implement our own bad block pattern: just one
byte at OOB start. Though, this will work only for x8 chips. For x16
chips two bytes must be checked. Since ELBC driver does not support x16
NANDs (yet), we're safe for now.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Fixes an issue with chip->state not always being set causing troubles.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Rather than scanning on boot, scan upon the first attempt to check the
badness of a block. This speeds up boot when not using NAND, and reduces
the likelihood of needing to reflash via JTAG if NAND becomes
nonfunctional.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Implement block-skipping read/write, based on a patch from
Morten Ebbell Hestens <morten.hestnes@tandberg.com>.
Signed-off-by: Morten Ebbell Hestnes <morten.hestnes@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The hardware has separate registers for block and page-within-block,
but the division between the two has no apparent relation to the
actual erase block size of the NAND chip.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Using current driver elbc sometimes hangs during nand write. Reading back
last byte helps though (thanks to Scott Wood for the idea).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This is a driver for the Flash Control Machine of the enhanched Local Bus
Controller found on some Freescale chips (such as the mpc8313 and the
mpc8379).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Some hardware, such as the enhanced local bus controller used on some
mpc83xx chips, does ecc transparently when reading and writing data, rather
than providing a generic calculate/correct mechanism that can be exported to
the nand subsystem.
The subsystem should not BUG() when calculate, correct, or hwctl are
missing, if the methods that call them have been overridden.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch turns off printing of bad blocks per default upon bootup.
This can always be shown via the "nand bad" command later.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch changes nand_wait_ready() to not just call nand_wait(),
since this will send a new command to the NAND chip. We just want to
wait for the chip to become ready here.
Signed-off-by: Stefan Roese <sr@denx.de>
- Fixing leading white spaces
- Fixing indentation where 4 spaces are used instead of tab
- Removing C++ comments (//), wherever I introduced them
Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
A lot changed in the Linux MTD code, since it was last ported from
Linux to U-Boot. This patch takes U-Boot NAND support to the level
of Linux 2.6.22.1 and will enable support for very large NAND devices
(4KB pages) and ease the compatibility between U-Boot and Linux
filesystems.
This patch is tested on two custom boards with PPC and ARM
processors running YAFFS in U-Boot and Linux using gcc-4.1.2
cross compilers.
MAKEALL ppc/arm has some issues:
* DOC/OneNand/nand_spl is not building (I have not tried porting
these parts, and since I do not have any HW and I am not familiar
with this code/HW I think its best left to someone else.)
Except for the issues mentioned above, I have ported all drivers
necessary to run MAKEALL ppc/arm without errors and warnings. Many
drivers were trivial to port, but some were not so trivial. The
following drivers must be examined carefully and maybe rewritten to
some degree:
cpu/ppc4xx/ndfc.c
cpu/arm926ejs/davinci/nand.c
board/delta/nand.c
board/zylonite/nand.c
Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Stig Olsen <stig.olsen@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch fixes NAND related printf format warning. Those warnings are
now visible since patch dc4b0b38d4
[Fix printf errors.] by Andrew Klossner has been applied. Thanks, this is
really helpful.
Signed-off-by: Stefan Roese <sr@denx.de>
This is particularly problematic now that non-NAND-specific code is
including <nand.h>, and thus all debugging code is being compiled
regardless of whether it was requested, as reported by Scott McNutt
<smcnutt@psyent.com>.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This is a re-write of the NAND FSL UPM driver using the more universal
hwcontrol callback (instead of the cmdfunc callback). Here is a brief
list of furher modifications:
- For the time being, the UPM setup writing the UPM array has been
removed from the driver and must now be done by the board specific
code.
- The bus width definition in "struct fsl_upm_nand" is now in bits to
comply with the corresponding Linux driver and 8, 16 and 32 bit
accesses are supported.
- chip->dev_read is only set if fun->dev_ready != NULL, which is
required for boards not connecting the R/B pin.
- A few issue have been fixed with MxMR bit manipulation like in the
corresponding Linux driver.
Note: I think the "io_addr" field of "struct fsl_upm" could be removed
as well, because the address is already determined by
"nand->IO_ADDR_[RW]", but I'm not 100% sure.
This patch has been tested on a TQM8548 modules with the NAND chip
Micron MT29F8G08FABWP.
This patch is based on the following patches posted to this list a few
minutes ago:
PPC: add accessor macros to clear and set bits in one shot
83xx/85xx/86xx: add more MxMR local bus definitions
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).
Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch correctly sets the oobavail variable
and fixes a bug where the oob data was not valid when
there where multiple groups in oobfree.
First segment fixes a typo
Second segment fixes a bug where oob data may be copied incorrectly.
Third segment adds an error message when exiting due to write protect.
Forth segment fixes a bug where oobavail may be set incorrectly.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
There are two NAND entries with ID 0xDC and this obviously causes problems.
In the kernel, they punted the first entry, so we should do the same.
See this upstream e-mail for more info:
http://lists.infradead.org/pipermail/linux-mtd/2007-July/018795.html
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
