Commit graph

1698 commits

Author SHA1 Message Date
Chris Packham
65d4d00abc net: Add support for mv88e609x switches
The Marvell Link Street mv88e60xx is a series of FastEthernet switch
chips, some of which also support Gigabit ports. It is similar to the
mv88e61xx series which support Gigabit on all ports.

The main difference is the number of ports. Which affects the
PORT_COUNT define and the size of the mask passed to
mv88e61xx_port_set_vlan().

Other than that it's just a matter of adding the appropriate chip
IDs.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Cc: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13 12:25:14 -05:00
Mugunthan V N
ab9715303d driver: net: cpsw: add support for RGMII id mode support and RMII clock source selection
cpsw driver supports only selection of phy mode in control module
but control module has more setting like RGMII ID mode selection,
RMII clock source selection. So ported to cpsw-phy-sel driver
from kernel to u-boot.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13 12:25:02 -05:00
Mugunthan V N
ce412b79e7 drivers: net: phy: atheros: add separate config for AR8031
In the current driver implementation, config() callback is common
for AR8035 and AR8031 phy. In config() callback, driver tries to
configure MMD Access Control Register and MMD Access Address Data
Register unconditionally for both phy versions which leads to
auto negotiation failure in AM335x EVMsk second port which uses
AR8031 Giga bit RGMII phy. Fixing this by adding separate config
for AR8031 phy.

Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13 12:24:55 -05:00
Andrea Merello
2ec4d10b65 phy: atheros: add support for RGMII_ID, RGMII_TXID and RGMII_RXID
This adds support for internal delay on RX and TX on RGMII interface for the
AR8035 phy.

This is basically the same Linux driver do. Tested on a Zynq Zturn board (for
which u-boot support in is my tree; first patch waiting ML approval)

Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13 12:24:51 -05:00
Robert P. J. Day
fc0b5948e0 Various, accumulated typos collected from around the tree.
Fix various misspellings of:

 * deprecated
 * partition
 * preceding,preceded
 * preparation
 * its versus it's
 * export
 * existing
 * scenario
 * redundant
 * remaining
 * value
 * architecture

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2016-10-06 20:57:40 -04:00
Heiko Schocher
592a749527 net, macb: fix misaligned cache operation warning
when using tftp on the smartweb board, it prints a lot of

CACHE: Misaligned operation at range [23b2e000, 23b2e100]

warnings ... fixed them.

Signed-off-by: Heiko Schocher <hs@denx.de>
2016-10-01 20:05:14 -04:00
Stefan Roese
544eefe084 net: mvneta: Add support for Armada 3700 SoC
This patch adds support for the Armada 3700 SoC to the Marvell mvneta
network driver.

Not like A380, in Armada3700, there are two layers of decode windows for GBE:
First layer is:  GbE Address window that resides inside the GBE unit,
Second layer is: Fabric address window which is located in the NIC400
                 (South Fabric).
To simplify the address decode configuration for Armada3700, we bypass the
first layer of GBE decode window by setting the first window to 4GB.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-09-27 17:29:52 +02:00
Stefan Roese
3cbc11da86 net: mvneta: Make driver 64bit safe
The mvneta driver is also used on the ARMv8 64bit Armada 3700 SoC. This
patch fixes the compilation warnings seen on this 64bit platform.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-09-27 17:29:52 +02:00
Stefan Roese
35e3fca7e3 net: mvneta: Round up top tx buffer boundaries for dcache ops
check_cache_range() warns that the top boundaries are not properly
aligned when flushing or invalidating the buffers and make these
operations fail.

This gets rid of the warnings:
CACHE: Misaligned operation at range ...

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-09-27 17:29:46 +02:00
Tom Rini
cbe7706ab8 Merge git://git.denx.de/u-boot-fsl-qoriq
trini: Drop local memset() from
examples/standalone/mem_to_mem_idma2intr.c

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-26 17:10:56 -04:00
York Sun
da28e58a7f armv8: ls1046a: Convert CONFIG_LS1046A to Kconfig option ARCH_LS1046A
Move this option to Kconfig and clean up existing uses.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Mingkai Hu <mingkai.hu@nxp.com>
CC: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-09-26 08:53:07 -07:00
Masahiro Yamada
5d97dff042 treewide: replace #include <asm-generic/errno.h> with <linux/errno.h>
Now, include/linux/errno.h is a wrapper of <asm-generic/errno.h>.
Replace all include directives for <asm-generic/errno.h> with
<linux/errno.h>.

<asm-generic/...> is supposed to be included from <asm/...> when
arch-headers fall back into generic implementation. Generally, they
should not be directly included from .c files.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Add drivers/usb/host/xhci-rockchip.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-23 22:25:27 -04:00
Masahiro Yamada
1221ce459d treewide: replace #include <asm/errno.h> with <linux/errno.h>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content.  (both just wrap <asm-generic/errno.h>)

Replace all include directives for <asm/errno.h> with <linux/errno.h>.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-23 17:55:42 -04:00
Paul Burton
96cb57c5ea net: pch_gbe: Make 64 bit safe
The pch_gbe driver previously casted pointers to & from unsigned 32 bit
integers in many locations. This breaks the driver on 64 bit systems,
producing streams of compiler warnings about mismatched pointer &
integer sizes and then failing to keep track of addresses correctly at
runtime.

Fix the driver for 64 bit systems by using unsigned longs in place of
the previously used 32 bit integers.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-09-21 15:04:32 +02:00
Paul Burton
154bf12f78 net: pch_gbe: Use dm_pci_map_bar to discover MMIO base
Reading the PCI BAR & converting the result to a physical address is not
safe across all architectures. For example on MIPS the virtual:physical
mapping is not 1:1, so we cannot directly make use of the physical
address.

Use the more generic BAR-mapping function dm_pci_map_bar to discover the
MMIO base address, which should work across architectures.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-09-21 15:04:32 +02:00
Zubair Lutfullah Kakakhel
2f1f05f432 net: emaclite: Enable driver for MIPS
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-09-21 14:55:14 +02:00
Zubair Lutfullah Kakakhel
611fe0bddb net: emaclite: use __raw_readl/writel instead of weird define
out_be32 and in_be32 are actually #defined to little endian
writel/readl in arch/microblaze.

Just use __raw_writel/readl instead. That is also what is used
in the Linux kernel driver for this IP block

Tested on MIPSfpga. Can tftp a kernel.

Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-09-21 14:55:14 +02:00
Zubair Lutfullah Kakakhel
39e020ef16 net: emaclite: Use ioremap_nocache
Virtual to physical mapping isn't necessarily 1:1 for all architectures

Using ioremap_nocache allows for the arch code to translate the
physical address to a virtual address.

Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-09-21 14:55:14 +02:00
Qianyu Gong
77b571da3b net: fm: fix spi flash probe for using driver model
The current code would always use the speed and mode set by
CONFIG_ENV_SPI_MAX_HZ and CONFIG_ENV_SPI_MODE. But if using
SPI driver model it should get the values from DT.

Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-09-14 14:04:56 -07:00
Beniamino Galvani
cfe255611c meson: odroid-c2: enable Ethernet support through the device tree
Remove the device definition from board file, update the driver with
the new compatible property and update config with necessary options.

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-09-06 13:18:19 -04:00
karl beldan
05237f735e net: davinci_emac: Restore the internal MDIO accessors return values
The spatch series converting legacy drivers from miiphy_register to
mdio_register changed the return convention of the davinci_emac internal
MDIO accessors, making the internal code relying on it misbehaving:
no mdiodev get registered and U-Boot crashes when using net cmds in the
context of the old legacy net API.

ATM davinci_emac_initialize and cpu_eth_init don't return a proper value
in that case but fixing them would not avoid the crash.

This change is just a follow-up to the spatch pass, the MDIO accessors
of the mdiodev introduced by the spatch pass retain their proper values.

Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-08-22 14:21:20 -05:00
Hou Zhiqiang
c23c7d461f net/fm: Remove unused code of FMan QMI
The QMan is not used in FMan IM mode, so no QMI enqueue or QMI
dequeue are performed.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-08-22 14:21:16 -05:00
karl beldan
a51897b6c1 net: davinci_emac: Invalidate only the received portion of a buffer
ATM when receiving a packet the whole buffer is invalidated, this change
optimizes this behaviour.

Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-08-22 14:21:13 -05:00
karl beldan
6202b8f28c net: davinci_emac: Round up top tx buffer boundaries for dcache ops
check_cache_range() warns that the top boundaries are not properly
aligned when flushing or invalidating the buffers and make these
operations fail.

This gets rid of the remaining warnings:
CACHE: Misaligned operation at range

Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-08-22 14:21:09 -05:00
karl beldan
a02c232336 net: davinci_emac: Remove useless dcache ops on descriptors
ATM the rx and tx descriptors are handled as cached memory while they
lie in a dedicated RAM of the SoCs, which is an uncached area.
Removing the said dcache ops, while optimizing the logic and clarifying
the code, also gets rid of most of the check_cache_range() incurred
warnings:
CACHE: Misaligned operation at range

Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-08-22 14:21:06 -05:00
Joe Hershberger
dfcc496ed7 net: mii: Changes not made by spatch
If the functions passed to the registration function are not in the same
C file (extern) then spatch will not handle the dependent changes.

Make those changes manually.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>

For the 4xx related files:
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-08-15 15:29:03 -05:00
Joe Hershberger
875e0bc68a net: mii: Fix changes made by spatch
Some of the changes were a bit too complex.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-08-15 15:29:03 -05:00
Joe Hershberger
5a49f17481 net: mii: Use spatch to update miiphy_register
Run scripts/coccinelle/net/mdio_register.cocci on the U-Boot code base.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-08-15 15:26:33 -05:00
Max Filippov
0d0779c141 net/ethoc: implement MDIO bus and support phylib
Implement MDIO bus read/write functions, initialize the bus and scan for
the PHY when phylib is enabled. Limit PHY speeds to 10/100 Mbps.

Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-08-15 13:34:49 -05:00
Max Filippov
59b7dfa0d1 net/ethoc: support private memory configurations
The ethoc device can be configured to have a private memory region
instead of having access to the main memory. In that case egress packets
must be copied into that memory for transmission and pointers to that
memory need to be passed to net_process_received_packet or returned from
the recv callback.

Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-08-15 13:34:48 -05:00
Max Filippov
02a888b567 net/ethoc: don't mix virtual and physical addresses
Addresses used in buffer descriptors and passed in platform data or
device tree are physical. Addresses used by CPU to access packet data
and registers are virtual. Don't mix these addresses and use virt_to_phys
for translation.

Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-08-15 13:34:48 -05:00
Max Filippov
2de18c8d77 net/ethoc: support device tree
Add .of_match table and .ofdata_to_platdata callback to allow for ethoc
device configuration from the device tree.

Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-08-15 13:34:47 -05:00
Max Filippov
5d43feabf3 net/ethoc: add CONFIG_DM_ETH support
Extract reusable parts from ethoc_init, ethoc_set_mac_address,
ethoc_send and ethoc_receive, move the rest under #ifdef CONFIG_DM_ETH.
Add U_BOOT_DRIVER, eth_ops structure and implement required methods.

Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-08-15 13:34:47 -05:00
Max Filippov
a84a757ae7 net/ethoc: use priv instead of dev internally
Don't use physical base address of registers directly, ioremap it first.
Save pointer in private struct ethoc and use that struct in all internal
functions.

Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-08-15 13:34:46 -05:00
Max Filippov
f0727120a7 net/ethoc: add Kconfig entry for the driver
Add Kconfig entry for the driver, remove #define CONFIG_ETHOC from the
only board configuration that uses it and put it into that board's
defconfig.

Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-08-15 13:34:46 -05:00
Alban Bedel
eb4e8ceb47 net: e1000: Fix the build with driver model and SPI EEPROM
When adding support for the driver model the SPI EEPROM feature had
been ignored. Fix the build with both CONFIG_DM_ETH and
CONFIG_E1000_SPI enabled.

Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-08-15 13:34:45 -05:00
Wenyou Yang
a212b66d7c net: macb: Fix build error for CONFIG_DM_ETH enabled
Use the right phy_connect() prototype for CONFIGF_DM_ETH.
Support to get the phy interface from dt and set GMAC_UR.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-08-15 13:34:44 -05:00
Tom Rini
f4b0df1823 Merge git://git.denx.de/u-boot-dm 2016-08-12 16:00:50 -04:00
Stephen Warren
6e06acb732 fdt: allow fdtdec_get_addr_size_*() to translate addresses
Some code may want to read reg values from DT, but from nodes that aren't
associated with DM devices, so using dev_get_addr_index() isn't
appropriate. In this case, fdtdec_get_addr_size_*() are the functions to
use. However, "translation" (via the chain of ranges properties in parent
nodes) may still be desirable. Add a function parameter to request that,
and implement it. Update all call sites to default to the original
behaviour.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Squashed in build fix from Stephen:
Signed-off-by: Simon Glass <sjg@chromium.org>
2016-08-12 09:20:27 -06:00
Lokesh Vutla
1f01962e0f drivers: net: cpsw: always flush cache of size aligned to PKTALIGN
cpsw tries to flush dcache which is not in the range of PKTALIGN.
Because of this the following warning comes while flushing:

CACHE: Misaligned operation at range [dffecec0, dffed016]

Fix it by flushing cache of size aligned to PKTALIGN.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-08-12 09:23:47 -04:00
Mugunthan V N
a61f6a5595 drivers: net: keystone_net: add support for multi slave ethernet
Keystone net can have multiple ethernet slaves, currently only
slave 1 is supported by the driver. Register multiple slaves as
individual ethernets to network framework.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-08-08 13:32:57 -04:00
Mugunthan V N
1610a9212a drivers: net: keystone_net: fix line termination with semi-colon
Each line should be terminated by semi-colon. It was not caught
earlier as there is a proper statement. Fix it by changing the
comma with semi-colon.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-08-08 13:32:56 -04:00
Vignesh R
2e205ef7eb net: cpsw: Add support to drive gpios for ethernet to be functional
On DRA72 EVM, cpsw slaves may be muxed with other modules. This
selection is controlled by a pcf gpio line. Add support for cpsw driver
to acquire mode-gpios and select the appropriate slave using gpio APIs.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-08-08 13:32:54 -04:00
Hans de Goede
4069437dfb net: sun8i_emac: Fix DMA alignment issues with the rx / tx buffers
This fixes the following CACHE warnings when using sun8i_emac:

=> dhcp
BOOTP broadcast 1
BOOTP broadcast 2
CACHE: Misaligned operation at range [7bf594a8, 7bf59628]
BOOTP broadcast 3
CACHE: Misaligned operation at range [7bf59c90, 7bf59e10]
CACHE: Misaligned operation at range [7bf5a478, 7bf5a5f8]
DHCP client bound to address 10.42.43.80 (1009 ms)

Note this commit also changes the max rx size from 2024 to 2044,
matching what the kernel driver uses.

Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Corentin LABBE <clabbe.montjoie@gmail.com>
Cc: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-07-31 21:45:46 +02:00
Tom Rini
4711e7f7af Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-07-28 08:45:00 -04:00
Simon Glass
fbfa1aba91 net: phy: marvell: Add a missing errno.h header
This corrects a build error on zynqmp.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-27 14:15:54 -06:00
Tom Rini
0b6699ad8e Merge branch 'master' of http://git.denx.de/u-boot-sunxi 2016-07-26 18:33:04 -04:00
Chen-Yu Tsai
a85ba87dbe net: sun8i_emac: Drop redundant and incorrect setting of syscon register
In sun8i_emac_board_setup, the driver partially configures the syscon
register for H3 EPHY. However, the settings are incomplete, and
completely unusable. The correct settings are later set in
sun8i_emac_set_syscon, but the incorrect CLK_SEL setting persists.

It is incorrect to use CLK_SEL to select 25 MHz, as the SoC does not
have a 25 MHz clock the EPHY can use.

This patch removes the setting of the syscon register in board_setup,
and also moves set_syscon above mdio_init. While mdio_init does not
access the PHY, it is better to have the PHY parameters setup before
the MDIO bus is registered.

Fixes: a29710c525 ("net: Add EMAC driver for H3/A83T/A64 SoCs.")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-26 21:56:03 +02:00
Chen-Yu Tsai
687284483c net: sun8i_emac: Do not configure AHB2 clock
The sun8i_emac driver erroneously configures the AHB2 clock when it
assumes it is configuring the AXI gates, which is not even documented
or ever appeared in either the WiP kernel driver or Allwinner's original
driver.

As a result, AHB2 clock mux is set to an invalid setting, making the
EPHY unusable.

Fixes: a29710c525 ("net: Add EMAC driver for H3/A83T/A64 SoCs.")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-26 21:56:02 +02:00
Mingkai Hu
9d3b8bd166 drivers: net/fm: Add Fman support for LS1046A
The Fman module on LS1046A is similiar with that on LS1043A but
LS1046A has one more XFI (10GbE) interface.

Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-07-26 09:02:32 -07:00
Amit Singh Tomar
a29710c525 net: Add EMAC driver for H3/A83T/A64 SoCs.
This patch add EMAC driver support for H3/A83T/A64 SoCs.
Tested on Pine64(A64-External PHY) and Orangepipc(H3-Internal PHY).

BIG Thanks to Andre for providing some of the DT code.

Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-15 08:34:34 +02:00
Hannes Schmelzer
0750701a3f driver/net/fec: support fixed speed connection
If MAC is directly connected to another MAC (like a switch for example)
we don't need to probe for a phy, autoneogation and so on. We simply
have to setup speed.

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-07-12 17:58:48 +02:00
Oleksandr Tymoshenko
4c64c4db3b net: rtl8169: Fix return value for rtl_send_common
Return value of rtl_send_common propogates unmodified all the way
up to eth_send and further to API consumer if CONFIG_API is enabled.
Previously rtl_send_common returned number of bytes sent on success
which was erroneouly detected as error condition by API consumers
that checked for operation success by comparing return value with 0.

Switch rtl_send_common to use common convention: return 0 on success
and negative value for failure.

Cc: Stephen Warren <swarren@nvidia.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Oleksandr Tymoshenko <gonzo@bluezbox.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-07-06 10:45:11 -05:00
Mingkai Hu
19c9ddaa4f driver: net: phylib: add support for aquantia AQR106/107 PHY
This patch adds support for aquantia AQR106/107 PHY.

Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-07-06 10:45:04 -05:00
Alexey Brodkin
66d027e22c net: designware: Make driver independent from DM_GPIO again
Commit 90b7fc924a "net: designware: support phy reset device-tree
bindings" made DW GMAC driver dependent on DM_GPIO by unconditional
usage of purely DM_GPIO stuff like:
 * dm_gpio_XXX()
 * gpio_request_by_name()

But since that driver as of today might be easily used without
DM_GPIO (that's the case for Synopsys AXS10x boards) we're
shielding all DM_GPIO things by ifdefs.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-07-06 10:45:00 -05:00
Nathan Rossi
08e64cece2 net: phy: marvell: Do not reset 88e1310 after autoneg
Commit a058052c "net: phy: do not read configuration register on reset",
changes the behaviour of the phy_reset function such that the state of
the BMCR register is not preserved during reset.

Change the config function for the m88e1310 so that it does not do a
reset after configuring auto-negotiation.

Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2016-06-21 17:01:52 -05:00
Alexey Firago
79887749f8 net: phy: micrel: add support for KSZ886x switches in MIIM mode
This patch adds a phy driver for the Micrel KSZ886x switches.

Similarly to the KSZ8895, SoC MAC is directly connected to the switch
MAC on the switch CPU port, so the link to the switch is always up.

KSZ886x switches can be used in the following configuration modes:
- Unmanaged mode with config stored in external EEPROM
- Managed mode over SPI
- Managed mode over I2C
- Managed mode over mdio/mdc (aka MIIM or SMI)

This patch supports only unmanaged and MIIM modes.

Based on Micrel KSZ886x driver from Linux kernel and
Micrel KSZ8895 driver from U-Boot.

Verified with the KSZ8863MLL.

Signed-off-by: Alexey Firago <alexey_firago@mentor.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-06-21 17:01:52 -05:00
Stephen Warren
dad7b74045 net: rtl8169: fix switching between adapters
The rtl8169 driver uses a global variable to store the register address
of the adapter being operated upon. This is updated to point at the
correct adapter when sending or receiving a packet, or shutting down the
adapter, but not when initializing the adapter. Consequently, switching
between different adapters within the same U-Boot runtime does not work
correctly since the driver programs the wrong registers during
rtl8169_eth_start() -> rtl8169_common_start() -> rtl8169_hw_start().

Note that since rtl8169_eth_stop() does set the global variable, the
second consecutive attempt to use the "new" adapter did work even before
this patch, because each time network usage is shut down, the network
core calls stop, which sets the variable so that the next start does
actually initialize the hardware, and the adapter works.

Equally, rtl8169_eth_probe() calls rtl_init() which sets the global, so
if using only a single device, or if picking the "right" device (based on
probe order) when multiple devices are present, ioaddr will already be set
correctly from the get-go, so the issue does not occur.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-06-21 17:01:51 -05:00
Tom Rini
fd9102dafe Merge branch 'master' of git://git.denx.de/u-boot-atmel 2016-06-13 08:50:58 -04:00
Simon Glass
f1dcc19b21 net: macb: Convert to driver model
Add driver-model support to this driver. The old code remains for now so
that we can convert boards one at a time.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-on: smartweb, corvus, taurus, axm
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
2016-06-12 23:49:38 +02:00
Simon Glass
f589f8cca6 net: macb: Flush correct cache portion when sending
The end address of the cache flush must be cache-line-aligned since
otherwise (at least on ARM926-EJS) the request is ignored. When the cache
is enabled this means that packets are not sent.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
2016-06-12 23:49:38 +02:00
Simon Glass
d5555b70e6 net: macb: Prepare for driver-model conversion
Adjust this driver to avoid using struct netdev in functions that driver
model will call. Also refactor the receive function to be compatible with
driver model.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-on: smartweb, corvus, taurus, axm
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
2016-06-12 23:49:38 +02:00
Tom Rini
3fc304b8d7 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-06-12 12:51:34 -04:00
Scott Wood
b616d9b0a7 nand: Embed mtd_info in struct nand_chip
nand_info[] is now an array of pointers, with the actual mtd_info
instance embedded in struct nand_chip.

This is in preparation for syncing the NAND code with Linux 4.6,
which makes the same change to struct nand_chip.  It's in a separate
commit due to the large amount of changes required to accommodate the
change to nand_info[].

Signed-off-by: Scott Wood <oss@buserror.net>
2016-06-03 20:27:48 -05:00
Marek Vasut
e40095f63b net: Add ag7xxx driver for Atheros MIPS
Add ethernet driver for the AR933x and AR934x Atheros MIPS machines.
The driver could be easily extended to other WiSoCs.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Wills Wang <wills.wang@live.com>
[fixed Kconfig dependency]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-05-31 09:38:11 +02:00
Paul Burton
bed1ca322d net: pcnet: Fix init on big endian 64 bit
If dev->iobase is 64 bits wide then writing the value of the BAR into a
pointer to iobase will not work on big endian systems, where the BAR
value will incorrectly get written to the upper 32 bits of the 64 bit
variable. Fix this by reading the BAR into a u32, matching the type
expected by pci_read_config_dword.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2016-05-31 09:38:11 +02:00
Paul Burton
442d2e0149 net: pcnet: Make 64 bit safe
Fix the pcnet driver to build safely on 64 bit platforms, in preparation
for allowing MIPS64 builds for Malta boards.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-31 09:38:11 +02:00
Paul Burton
4677d665a7 net: pcnet: Stop converting kseg1->kseg0 addresses
Now that MIPS virt_to_phys can handle kseg1 addresses on MIPS32, stop
manually converting addresses to their kseg0 equivalents in the pcnet
driver.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2016-05-31 09:38:11 +02:00
Tom Rini
378f9134eb Merge git://git.denx.de/u-boot-rockchip 2016-05-27 15:48:53 -04:00
Beniamino Galvani
0e1a3e30de net: designware: fix descriptor layout and warnings on 64-bit archs
All members of the DMA descriptor must be 32-bit, even on 64-bit
architectures: change the type to u32 to ensure this. Also, fix
other warnings.

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Use phys_addr_t not unsigned long long to test that we're within
DMA'able memory]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:39:46 -04:00
Sjoerd Simons
90b7fc924a net: designware: support phy reset device-tree bindings
Add support for the snps,reset-gpio, snps,reset-active-low (optional) and
snps,reset-delays-us device-tree bindings. The combination of these
three define how the PHY should be reset to ensure it's in a sane state.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-27 09:00:48 -06:00
Tom Rini
826d06dbdd Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2016-05-25 07:19:31 -04:00
Ying Zhang
8ef548d5f1 powerpc:t4240: MAC9 and MAC10 should not be identified as 1G interface in some case
When using rcw protocols to support 10G on MAC9 and MAC10, these MACs
should not be identified as 1G interface, otherwise, one MAC will be
listed as two Ethernet ports. For example, MAC9 will be listed as
FM1@TGEC1 and FM1@DTSEC9.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-24 17:11:03 -07:00
Tom Rini
2ee490a024 Merge branch 'master' of git://git.denx.de/u-boot-net
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	drivers/net/zynq_gem.c
2016-05-24 11:59:02 -04:00
Dan Murphy
0a71cd7729 net: phy: dp83867: Add SGMII helper for configuration
The code assumed that if the interface is not RGMII configured
then it must be SGMII configured.  This device has the ability
to support most of the MII interfaces.  Therefore add the
helper for SGMII and only configure the device if the interface is
configured for SGMII.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24 11:42:05 -05:00
Dan Murphy
3ab72fe807 net: phy: Move is_rgmii helper to phy.h
Move the phy_interface_is_rgmii to the phy.h
file for all phy's to be able to use the API.

This now aligns with the Linux kernel based on
commit e463d88c36d42211aa72ed76d32fb8bf37820ef1

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24 11:42:05 -05:00
Dan Murphy
085445ca41 net: phy: ti: Allow the driver to be more configurable
Not all devices use the same internal delay or fifo depth.
Add the ability to set the internal delay for rx or tx and the
fifo depth via the devicetree.  If the value is not set in the
devicetree then set the delay to the default.

If devicetree is not used then use the default defines within the
driver.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24 11:42:04 -05:00
Dan Murphy
20671a9896 net: zynq_gem: Add the passing of the phy-handle node
Add the ability to pass the phy-handle node offset
to the phy driver.  This allows the phy driver
to access the DT subnode's data and parse accordingly.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24 11:42:04 -05:00
Dan Murphy
cb3862277b drivers: net: cpsw: Add reading of DT phy-handle node
Add the ability to read the phy-handle node of the
cpsw slave.  Upon reading this handle the phy-id
can be stored based on the reg node in the DT.

The phy-handle also needs to be stored and passed
to the phy to access any phy data that is available.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24 11:42:04 -05:00
Mugunthan V N
e4310566de drivers: net: cpsw: add support for reading mac address from efuse
Different TI platforms has to read with different combination to
get the mac address from efuse. So add support to read mac address
based on machine/device compatibles.

The code is taken from Linux drivers/net/ethernet/ti/cpsw-common.c
done by Tony Lindgren.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24 11:42:03 -05:00
Mugunthan V N
66e740cbbd drivers: net: cpsw: fix get mdio base and gmii_sel reg from DT
Since dra7x platforms address bus is define as 64 bits to support
LAPE, fdtdec_get_addr() returns a invalid address for mdio based
and gmii_sel register address. Fixing this by using
fdtdec_get_addr_size_auto_noparent() which will derive address
cell and size cell from its parent.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24 11:42:02 -05:00
Mugunthan V N
b2003c5458 drivers: net: cpsw: fix cpsw dp parse when num slaves as 1
On some boards number of slaves can be 1 when only one port
ethernet is pinned out. So do not break when slave_index and
num slaves check fails, instead continue to parse the next
child.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24 11:42:02 -05:00
Kevin Smith
24ae3961f8 net: phy: Add PHY driver for mv88e61xx switches
The previous mv88e61xx driver was a driver for configuring the
switch, but did not integrate with the PHY/networking system, so
it could not be used as a PHY by U-boot.  This is a complete
rework to support this device as a PHY.

Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24 11:39:04 -05:00
Kevin Smith
83c05515d8 net: Remove unused mv88e61xx switch driver
No boards are using this driver.  Remove in preparation for a new
driver with integrated PHY support.

Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
2016-05-24 11:39:04 -05:00
Peng Fan
87f9989502 net: fec_mxc: use simpler runtime cpu dection macros
Use simpler runtime cpu dection macros.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24 14:59:57 +02:00
Michal Simek
1b008fdb06 phy: marvell: Do not reset phy after negotiation
The patch
"net: phy: do not read configuration register on reset"
(sha1: a058052c35)
was causing regression on zynq zc702 board where Marwell 88e1118
phy was resetted after negotiation was setup.
Phy reset is done pretty early in phy_connect_dev() and doens't need to
be called again in phy code.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24 13:17:59 +02:00
Michal Simek
7a673f0b06 phy: Wire return value from phy_config()
Fix zynq_gem driver to handle error from phy_config correctly.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24 13:17:59 +02:00
Michal Simek
b733c278d7 net: phy: Handle phy_startup() error codes properly
Propagate error code from genphy_update_link() to phy startup().

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
2016-05-24 13:17:59 +02:00
Michal Simek
ef5e821bd8 phy: Return correct error code when timeout happens
Return -ETIMEDOUT if timeout happens.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
2016-05-24 13:17:59 +02:00
Michal Simek
55259e7cda net: xilinx: Handle error value from phy_startup()
Handle error returned by phy_startup() properly.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
2016-05-24 13:17:55 +02:00
Robert P. J. Day
1cc0a9f496 Fix various typos, scattered over the code.
Spelling corrections for (among other things):

* environment
* override
* variable
* ftd (should be "fdt", for flattened device tree)
* embedded
* FTDI
* emulation
* controller
2016-05-05 21:39:26 -04:00
Prabhakar Kushwaha
31a48cf4e1 drivers: net: ldpaa: Memset pools_params as "0" before use
Memset pools_params as "0" to avoid garbage value in dpni_set_pools.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reported-by: Jose Rivera <german.rivera@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-03 17:52:11 -05:00
Vagrant Cascadian
eae4b2b67b Fix spelling of "occurred".
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-02 18:37:09 -04:00
York Sun
3c1d218a1d armv8: LS2080A: Consolidate LS2080A and LS2085A
LS2080A is the primary SoC, and LS2085A is a personality with AIOP
and DPAA DDR. The RDB and QDS boards support both personality. By
detecting the SVR at runtime, a single image per board can support
both SoCs. It gives users flexibility to swtich SoC without the need
to reprogram the board.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2016-04-06 10:26:46 -07:00
Codrin Ciubotariu
9101a68c15 drivers: net: vsc9953: Fix bug when PVID is shown for disabled ports only
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-04-06 08:34:44 -07:00
Codrin Ciubotariu
02c00f265d drivers: net: vsc9953: Do not configure disabled ports
Some SerDes protocols might not enable all l2switch ports. In this case,
these ports should not be configured to perform Rx/Tx operations.
This also fixes an issue when flooded frames were also switched to
disabled ports and frames start to accumulate, consuming memory
and eventually causing head-of-line blocking for other frames.

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-04-06 08:34:18 -07:00
Tom Rini
4ed6ed3c27 Merge branch 'master' of git://www.denx.de/git/u-boot-microblaze 2016-04-04 14:34:09 -04:00
Siva Durga Prasad Paladugu
845ee5f623 net: zynq_gem: Add SGMII support for zynqMP
PCS auto negotaiation bit should be enabled
along with SGMII autonegotation enabled
in phy.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-04 20:28:39 +02:00
Siva Durga Prasad Paladugu
85b949f40b net: phy: Add SGMII support for TI phy
Add support of SGMII to TI phy dp838367
Enable the SGMII and PCS settings in phy
control, CFG2 and BIST registers

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-04 20:28:39 +02:00
Siva Durga Prasad Paladugu
e76d2dcaeb net: zynq_gem: Return error incase of invalid phy address
Return error from probe in case of invalid phy address.
This fixes the issue of uboot crash if phy is not detected.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-04 20:28:39 +02:00
Michal Simek
ceb04e1a5d net: axi_emac: Report phy-node error message permanently
Do not use debug() when printing error message. Use printf instead.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-04 20:28:38 +02:00
Joe Hershberger
a509a1d402 net: gem: Allow to set the MAC from an EEPROM
Provide board specific option how to read MAC address from ROM.
Do it in generic way to be reusable by differnet boards.
If this is not enough board specific functions can be created.

Signed-off-by: Joe Hershberger <joe.hershberger@gmail.com> # driver part
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-04 20:27:54 +02:00
Siva Durga Prasad Paladugu
8964f24179 net: xilinx_axi: Clear Isolate bit if found during phy setup
In SGMII cases the isolate bit might set after DMA and
ethernet resets and hence check and clear during
setup_phy if it was set.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-04 20:10:44 +02:00
Siva Durga Prasad Paladugu
9c0da76220 net: xilinx_axi: Use interface type instead of zero
Pass appropriate interface type to phy_connect
instead of zero.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-04 20:10:44 +02:00
Siva Durga Prasad Paladugu
a06c341faa net: zynq_gem: Add support for SGMII interface
Add support of SGMII interface for zynq GEM.
Read xlnx,emio property from DT.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-04 20:10:44 +02:00
Siva Durga Prasad Paladugu
ed6fad3e25 phy: Add phy driver support for xilinx PCS/PMA core
Add phy driver support for xilinx PCS/PMA core

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-04 20:10:44 +02:00
Stefan Roese
99d4c6d3b2 net: mvpp2.c: Add Marvell mvpp2 network driver for Armada 375
This patch adds support for the mvpp2 ethernet controller which is integrated
in the Marvell Armada 375 SoC. This port is based on the Linux driver (v4.4),
which has been stripped of the in U-Boot unused portions.

Tested on the Marvell Armada 375 eval board db-88f6720.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Acked-by: Joe Hershberger <joe.hershberger@gmail.com>
2016-04-04 11:21:40 +02:00
Karsten Merker
563d8d9358 net: phy: Realtek RTL8211B/C PHY ID fix
The RTL8211B_driver structure in drivers/net/phy/realtek.c contains a
wrong PHY ID (0x1cc910 instead of 0x1cc912) in the uid field.

The lowest four bits of the PHY ID encode the chip revision (B+C/D/E/F)
of the RTL8211 and the code originally applied a mask of 0xfffff0 to
the PHY ID, so that matching the PHY ID to the appropriate driver code
was only done on the chip type (RTL8211), but not on a specific
revision.

After introduction of support for the RTL8211E, which needed another
startup function than the older chip revisions, commit
4220504767 changed the mask to 0xffffff
to make the chip revision relevant for the match, but didn't provide
the now-relevant lower bits of the uid field for the RTL8211B/C.

Fix this by setting the full PHY ID in the RTL8211B_driver uid field.

Fixes: 4220504767 ("net/phy: realtek: Fix the PHY ID mask to ensure the correct Realtek PHY is detected")
Signed-off-by: Karsten Merker <merker@debian.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-04-02 19:26:08 -04:00
Michael Haas
525d187afb net: phy: Optionally force master mode for RTL PHY
This patch introduces CONFIG_RTL8211X_PHY_FORCE_MASTER. If this
define is set, RTL8211x PHYs (except for the RTL8211F) will have their
1000BASE-T master/slave autonegotiation disabled and forced to master
mode.

This is helpful for PHYs like the RTL8211C which produce unstable links
in slave mode. Such problems have been found on the A20-Olimex-SOM-EVB
and A20-OLinuXino-Lime2.

There is no proper way to identify affected PHYs in software as the
RTL8211C shares its UID with the RTL8211B. Thus, this fix requires
the introduction of an #ifdef.

CC: fradav@gmail.com
CC: merker@debian.org
CC: hdegoede@redhat.com
CC: ijc@hellion.org.uk
CC: joe.hershberger@ni.com

Signed-off-by: Michael Haas <haas@computerlinguist.org>
Tested-by: Karsten Merker <merker@debian.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-03-31 14:29:11 +02:00
Tom Rini
0badc648dc Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-03-29 12:58:45 -04:00
Prabhakar Kushwaha
b576d325ac driver: net: fsl-mc: Check NULL before pointer dereference
NULL pointer should be checked before any dereference.  This patch
move memest after the NULL pointer check.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reported-by: Jose Rivera <german.rivera@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-29 08:46:01 -07:00
Prabhakar Kushwaha
cd7b3fbcf4 driver: net: fsl-mc: Free dflt_dpio pointer after its usage
Free dflt_dpio pointer after its usage during error handling

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reported-by: Jose Rivera <german.rivera@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-28 17:35:38 -07:00
Bin Meng
dbe253861a net: rtl8169: Fix build error when DEBUG is on
When DEBUG_RTL8169 is on, a build error occurs in function
'rtl_init': error: 'dev' undeclared. Fix this.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-03-27 09:12:25 -04:00
Bin Meng
0764f24ae6 net: Move CONFIG_RTL8169 to Kconfig
Introduce CONFIG_RTL8169 in Kconfig and move over boards' defconfig
to use that.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Stephen Warren <swaren@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-03-22 12:19:53 -04:00
Bin Meng
86e9dc86b1 net: Move CONFIG_RTL8139 to Kconfig
Introduce CONFIG_RTL8139 in Kconfig and move over boards' defconfig
to use that.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: Fixup MPC8641HPCN* and r2dplus configs]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-22 12:19:27 -04:00
Prabhakar Kushwaha
6dedcedd64 driver: net: fsl-mc: Return from DPAA_exit if boot_status !=0
Return value of get_mc_boot_status() in case of failure is not necessary
to be -1.

So update the error condition check.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reported-by: Yao Yuan <yao.yuan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-21 12:42:15 -07:00
Prabhakar Kushwaha
6c2b520a37 driver: net: ldpaa_eth: Add support of PHY framework
This patch integrate DPAA2 ethernet driver existing PHY framework.

Call phy_connect and phy_config as per available DPMAC id defined
in SerDes Protcol.

Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-21 12:42:14 -07:00
Simon Glass
73223f0e1b Kconfig: Move CONFIG_FIT and related options to Kconfig
There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.

Move these options to Kconfig and tidy up board configuration:

   CONFIG_FIT
   CONFIG_OF_BOARD_SETUP
   CONFIG_OF_SYSTEM_SETUP
   CONFIG_FIT_SIGNATURE
   CONFIG_FIT_BEST_MATCH
   CONFIG_FIT_VERBOSE
   CONFIG_OF_STDOUT_VIA_ALIAS
   CONFIG_RSA

Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.

Note: Masahiro's moveconfig.py script is amazing.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:07 -04:00
Alison Wang
903d384d40 net: phy: atheros: Fix problem with phy_reset() clearing BMCR
In commit <a058052c358c> [net: phy: do not read configuration register on
reset], phy_reset() will clear the BMCR register. Bit 12(AUTO_NEGOTIATION)
is cleared too. It causes auto-negotiation timeout error on Atheros's
PHY AR8033.

To fix this problem, genphy_config_aneg() and genphy_restart_aneg()
needs to be called in ar8035_config() to enable and restart
auto-negotiation.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-02-26 13:32:37 -06:00
Tom Rini
e1417c7b66 Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-02-24 18:44:15 -05:00
Qianyu Gong
6fc9535f39 driver/fm: fdt.c: fix fdt_fixup_fman_firmware() to support ARM platforms
Use fdt32_to_cpu() to convert the data correctly for both endianness
platforms.

Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24 08:51:13 -08:00
Qianyu Gong
075affb1ac fm: fdt: Move fman ucode fixup to driver code
Not only powerpc/mpc85xx but also Freescale Layerscape platforms will
use fdt_fixup_fman_firmware() to insert Fman ucode blob into the device
tree. So move the function to Fman driver code.

Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24 08:51:13 -08:00
Qianyu Gong
2459afb1a7 qe: move drivers/qe/qe.h to include/fsl_qe.h
As the QE firmware struct is shared with Fman, move the header file
out of drivers/qe/.

Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24 08:51:13 -08:00
Michal Simek
6a10bc5be8 net: phy: realtek: Use generic genphy_parse_link() for RTL8211E
The problem with current implementation is that SPDDONE bit is 1
but link bit is zero. That's why phydev->link is setup to 0
which ending up in driver failure that link is not up.

Log:
Zynq> dhcp
ethernet@e000b000 Waiting for PHY auto negotiation to complete.......
done
ethernet@e000b000: No link.

There is at least 1ms delay between spddone bit and link up.

Use genphy_read_status() instead of realtek implemenation which is
working with page 11. Linux driver is also using generic implementation.

Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-02-22 16:37:50 +01:00
Tom Rini
20680b560a Merge branch 'master' of git://git.denx.de/u-boot-atmel 2016-02-20 17:32:48 -05:00
Wenyou Yang
cd4de1d928 drivers: at91: clean up peripheral clock code
Due to introducing the new peripheral clock handle functions,
use these functions to reduce the duplicated code.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
[fixup for missing clk.h in at91_emac.c]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2016-02-18 21:34:40 +01:00
Stefan Roese
a8c3eca433 net: phy: marvell: Fix problem with phy_reset() clearing BMCR
With commit a058052c [net: phy: do not read configuration register on
reset], phy_reset() will clear the BMCR register. Resulting in bit 12
being cleared (A/N enable). This leads to autonegotiation link problems,
at least on the Marvell Armada ClearFog board. I suspect that other
boards using this driver will be affected as well.

At the of m88e1111s_config(), phy_reset() is called. This is not needed
for the PHY to load the changed configuration, as phy_reset() is called
a few lines before already. So lets call genphy_restart_aneg() here
instead to start the AN correctly.

Tested on clearfog.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Hao Zhang <hzhang@ti.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-02-18 11:32:03 -06:00
Stefan Roese
3089c47ddc net: phy: marvell: Call phy_reset() where possible
Instead of coding the soft PHY reset function multiple times in marvell.c,
lets call the common phy_reset() function from phy.c.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Hao Zhang <hzhang@ti.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-02-18 11:32:00 -06:00
Mugunthan V N
6599f3690c drivers: net: keystone_net: convert driver to adopt device driver model
Adopt keystone_net driver to adopt device driver model

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-02-08 10:10:46 -05:00
Mugunthan V N
347348f9f7 drivers: net: phy: micrel: fix build errors with CONFIG_DM_ETH
When Micrel phy is selected without CONFIG_PHY_MICREL_KSZ9031 or
CONFIG_PHY_MICREL_KSZ9021 there  is a build error. Fixing this
by adding proper ifdefs

drivers/net/phy/micrel.c:370:39: error: array type has incomplete element type
 static const struct ksz90x1_reg_field ksz9031_ctl_grp[] =
                                       ^
drivers/net/phy/micrel.c:372:39: error: array type has incomplete element type
 static const struct ksz90x1_reg_field ksz9031_clk_grp[] =
                                       ^
drivers/net/phy/micrel.c: In function ‘ksz9031_of_config’:
drivers/net/phy/micrel.c:377:23: error: array type has incomplete element type
  struct ksz90x1_ofcfg ofcfg[] = {
                       ^
drivers/net/phy/micrel.c:379:13: error: ‘ksz90x1_rxd_grp’ undeclared (first use in this function)
   { MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW, 2, ksz90x1_rxd_grp, 4 },
             ^
drivers/net/phy/micrel.c:379:13: note: each undeclared identifier is reported only once for each function it appears in
drivers/net/phy/micrel.c:380:13: error: ‘ksz90x1_txd_grp’ undeclared (first use in this function)
   { MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW, 2, ksz90x1_txd_grp, 4 },
             ^
drivers/net/phy/micrel.c:386:3: warning: implicit declaration of function ‘ksz90x1_of_config_group’ [-Wimplicit-function-declaration]
   ret = ksz90x1_of_config_group(phydev, &(ofcfg[i]));
   ^
drivers/net/phy/micrel.c:377:23: warning: unused variable ‘ofcfg’ [-Wunused-variable]
  struct ksz90x1_ofcfg ofcfg[] = {
                       ^
drivers/net/phy/micrel.c: At top level:
drivers/net/phy/micrel.c:370:39: warning: ‘ksz9031_ctl_grp’ defined but not used [-Wunused-variable]
 static const struct ksz90x1_reg_field ksz9031_ctl_grp[] =
                                       ^
drivers/net/phy/micrel.c:372:39: warning: ‘ksz9031_clk_grp’ defined but not used [-Wunused-variable]
 static const struct ksz90x1_reg_field ksz9031_clk_grp[] =
                                       ^
scripts/Makefile.build:277: recipe for target 'drivers/net/phy/micrel.o' failed
make[1]: *** [drivers/net/phy/micrel.o] Error 1
Makefile:1201: recipe for target 'drivers/net/phy' failed
make: *** [drivers/net/phy] Error 2
make: *** Waiting for unfinished jobs....

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-02-08 10:10:45 -05:00
Tom Rini
57dc53a724 Merge branch 'agust@denx.de' of git://git.denx.de/u-boot-staging 2016-02-08 09:48:04 -05:00
Vishwas Srivastava
2300184f70 net: davinci_emac: fix NULL check after pointer dereference
NULL check is made after the pointer dereference. This patch
fixes this issue.

Signed-off-by: Vishwas Srivastava <vishu.kernel@gmail.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2016-02-06 16:39:31 +01:00
Vishwas Srivastava
abbf2d9b56 net: fix wrong initialization in davinci-emac driver
emac module of the davinci platform supports only 8 tx and 8
rx channels (total 16). emac driver for davinci platform,
however, while doing initialization of the dma descriptor
head pointers, wrongly initializes the 16 head pointers
(instead of  8) for tx dma and 16 head pointers (insted of 8)
for rx dma, which is wrong. The result is, that this register
initilization spills over the other registers which was not
intended and is undesirable. This patch fixes this problem.

Signed-off-by: Vishwas Srivastava <vishu.kernel@gmail.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2016-02-06 15:11:57 +01:00
Bin Meng
a187559e3d Use correct spelling of "U-Boot"
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
2016-02-06 12:00:59 +01:00
Bin Meng
81dab9af92 net: e1000: Convert to use DM PCI API
Update this driver to use proper DM PCI APIs.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-02-05 12:47:23 +08:00
Bin Meng
6758a6ccc1 net: designware: Use dm_pci_mem_to_phys() in the probe routine
Convert to use native DM PCI API dm_pci_mem_to_phys().

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-02-05 12:47:23 +08:00
Bin Meng
c52ac3f901 net: pch_gbe: Convert to use DM PCI API
Use native DM PCI APIs instead of legacy compatible ones.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-02-05 12:47:23 +08:00
Tom Rini
161b1fe745 Merge branch 'master' of git://git.denx.de/u-boot-atmel 2016-02-02 07:24:52 -05:00
Tom Rini
008e61f512 Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-02-02 06:51:05 -05:00
Purna Chandra Mandal
23e7578c9b drivers: net: Add ethernet driver for Microchip PIC32.
This driver implements MAC and MII layer of the ethernet controller.
Network data transfer is handled by controller internal DMA engine.
Ethernet controller is configurable through device-tree file.

Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
2016-02-01 22:14:02 +01:00
Purna Chandra Mandal
46c9d938ca drivers: net: phy: add SMSC LAN8740 Phy support.
Add SMSC LAN8740 Phy support required for PIC32MZDA devices.

Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-02-01 22:14:02 +01:00
Prabhakar Kushwaha
a2a4dc565d driver: net: fsl-mc: Update print to reflect correct string
Update printf with dpbp_exit to match with previous function call.

Signed-off-by: Itai Katz <itai.katz@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-01 09:11:11 -08:00
Prabhakar Kushwaha
5373b204df driver: net: fsl-mc: Memset dprc_cfg before configuring
All fields of struct dprc_cfg are not being configured while creating
child container. "Not" configured fields are assumed to be 0.

So memset dprc_cfg before configuring the fields.

Signed-off-by: Itai Katz <itai.katz@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-01 09:11:11 -08:00
Tom Rini
82d72a1b99 Merge branch 'master' of git://git.denx.de/u-boot-net 2016-01-28 18:42:10 -05:00
Shaohui Xie
d8877e6f8c net: phy: implements probe for Cortina phy
Cortina phy cannot support soft reset, this commit implements probe
for Cortina PHY to tell phylib to skip phy soft reset by setting
PHY_FLAG_BROKEN_RESET in flags.

Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 13:20:31 -06:00
Shaohui Xie
ddcd1f3084 net: phy: introduce a quirk PHY_FLAG_BROKEN_RESET
Current driver always performs a phy soft reset when connecting the phy
device, but soft reset is not always supported by a phy device, so
introduce a quirk PHY_FLAG_BROKEN_RESET to let such a phy device to skip
soft reset. This commit uses 'flags' of phy device structure to store the
quirk.

Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 13:20:30 -06:00
Dinh Nguyen
ff7bd212cb net: phy: micrel: fix divisor value for KSZ9031 phy skew
The picoseconds to register value divisor(ps_to_regval) should be 60 and not
200. Linux has KSZ9031_PS_TO_REG defined to be 60 as well. 60 is the correct
divisor because the 4-bit skew values are defined from 0x0000(-420ps) to
0xffff(480ps), increments of 60.

For example, a DTS skew value of 420, represents 0ps delay, which should be 0x7.
With the previous divisor of 200, it would result in 0x2, which represents a
-300ps delay.

With this patch, ethernet on the SoCFPGA DE0 Atlas is now able to work with
1Gb ethernet.

References:
http://www.micrel.com/_PDF/Ethernet/datasheets/KSZ9031RNX.pdf -> page 26

Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 13:20:30 -06:00
Alexandre Messier
1f9e672c79 net: phy: Use 'autoneg' flag from phydev
Use the 'autoneg' flag available in phydev when checking if
autoneg is in use.

The previous implementation was checking directly in the PHY
if autoneg was supported. Some PHYs will report that autoneg
is supported, even when it is disabled. Thus it is not possible
to use that bit to determine if autoneg is currently in use or
not.

Signed-off-by: Alexandre Messier <amessier@tycoint.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 13:20:29 -06:00
Alexandre Messier
53b0c38c7a net: phy: Set ANRESTART in setup_forced
When configuring a PHY in fixed (forced) link mode, in order for
the changes to be applied, either one of these conditions must
be triggered:
	1- PHY is reset
	2- Autoneg is restarted
	3- PHY transitions from power-down to power-up

Neither of these is currently done, so effectively the fixed link
configuration is not applied in the PHY.

Fix this by setting the Autoneg restart bit.

Signed-off-by: Alexandre Messier <amessier@tycoint.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 13:20:28 -06:00
Alexandre Messier
79e3efd5e5 net: phy: micrel: Disable B_CAST on config
Micrel PHYs KSZ8021/31 and KSZ8081 have a feature where MDIO address 0
is considered as a broadcast address; the PHY will respond even if it
is not its configured (pinstrapped) address. This feature is enabled
by default.

The Linux kernel disables that feature at initialisation, but not
before it probes the MDIO bus. This causes an issue, because a PHY
at address 3 will be discovered at addresses 0 and 3, but will then
only respond at address 3. Because Linux attaches the first PHY it
discovers on 'eth0', it will attach the PHY from address 0, which
will never answer again.

Fix the issue by disabling the broadcast feature in U-Boot, before
Linux is started.

Signed-off-by: Alexandre Messier <amessier@tycoint.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 13:20:21 -06:00
Alexey Brodkin
6968ec9216 net/designware: add support of max-speed device tree property
This property allows to specify fastest connection mode supported by
the MAC (as opposed to features of the phy).

There are situations when phy may handle faster modes than the
MAC (or even it's particular implementation or even due to CPU being too
slow).

This property is a standard one in Linux kernel these days and some
boards do already use it in their device tree descriptions.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
cc: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 12:32:44 -06:00
Alexey Brodkin
b884c3fe63 net/designware: do explicit port selection for 1Gb mode
Current implementation only sets "port select" bit for non-1Gb mode.
That works fine if GMAC has just exited reset state but we may as well
change connection mode in runtime. Then we'll need to reprogram GMAC for
that new mode of operation and if previous mode was 10 or 100 Mb and new
one is 1 Gb we'll need to reset port mode bit.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
cc: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 12:32:43 -06:00
Alexey Brodkin
b18acb0a11 drivers/net/phy: introduce phy_set_supported()
This new function will allow MAC drivers to override supported
capabilities of the phy. It is required when MAC cannot handle all
speeds supported by phy.

For example phy supports up-to 1Gb connections while MAC may only work
in modes up to 100 or even 10 Mbit/sec.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 12:32:42 -06:00
Sascha Hauer
44bc317487 net: phy: genphy: Allow overwriting features
of_set_phy_supported allows overwiting hardware capabilities of
a phy with values from the devicetree. This does not work with
the genphy driver though because the genphys config_init function
will overwrite all values adjusted by of_set_phy_supported. Fix
this by initialising the genphy features in the phy_driver struct
and in config_init just limit the features to the ones the hardware
can actually support. The resulting features are a subset of the
devicetree specified features and the hardware features.

This is a copy of the patch from Linux kernel, see
http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=c242a47238fa2a6a54af8a16e62b54e6e031d4bc

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 12:32:41 -06:00
Florian Fainelli
bbdcaff12a net: phy: ensure Gigabit features are masked off if requested
When a Gigabit PHY device is connected to a 10/100Mbits capable Ethernet
MAC, the driver will restrict the phydev->supported modes to mask off
Gigabit. If the Gigabit PHY comes out of reset with the Gigabit features
set by default in MII_CTRL1000, it will keep advertising these feature,
so by the time we call genphy_config_advert(), the condition on
phydev->supported having the Gigabit features on is false, and we do not
update MII_CTRL1000 with updated values, and we keep advertising Gigabit
features, eventually configuring the PHY for Gigabit whilst the Ethernet
MAC does not support that.

This patches fixes the problem by ensuring that the Gigabit feature bits
are always cleared in MII_CTRL1000, if the PHY happens to be a Gigabit
PHY, and then, if Gigabit features are supported, setting those and
updating MII_CTRL1000 accordingly.

This is a copy of patch from Linux kernel, see
http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=5273e3a5ca94fbeb8e07d31203069220d5e682aa

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 12:31:30 -06:00
Bin Meng
a1c76c1508 net: tsec: Use priv->tbiaddr to initialize TBI PHY address
Add a new member 'tbiaddr' to tsec_private struct. For non-DM driver,
it is initialized as CONFIG_SYS_TBIPA_VALUE, but for DM driver, we
can get this from device tree. Update the bindings doc as well.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 12:23:19 -06:00
Bin Meng
9a1d6af55e net: tsec: Add driver model ethernet support
This adds driver model support to Freescale TSEC ethernet driver.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 12:23:15 -06:00
Bin Meng
56a27a1e6c net: tsec: Use tsec_private pointer as the parameter for internal routines
For internal routines like redundant_init(), startup_tsec() and
init_phy(), change to use tsec_private pointer as the parameter.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 12:23:07 -06:00
Bin Meng
8ba50176fc net: tsec: Adjust orders to avoid forward declaration of tsec_send()
Adjust static functions in a proper order so that forward declaration
of tsec_send() can be avoided.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 12:23:03 -06:00
Bin Meng
e677da9723 net: tsec: Move rxbd and txbd to struct tsec_private
rxbd and txbd are declared static with 8 byte alignment requirement,
but they can be put into struct tsec_private as well and are natually
aligned to 8 byte.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 12:22:59 -06:00
Bin Meng
362b123f47 net: tsec: Move rx_idx and tx_idx to struct tsec_private
At present rx_idx and tx_idx are declared as static variables
in the driver codes. To support multiple interfaces, move it to
struct tsec_private.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 12:22:55 -06:00
Bin Meng
9872b736f9 net: tsec: fsl_mdio: Fix several cosmetic issues
Clean up the tsec and fsl_mdio driver codes a little bit, by:
- Fix misuse of tab and space here and there
- Use correct multi-line comment format
- Replace license identifier to GPL-2.0+

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 12:22:49 -06:00
Codrin Ciubotariu
aae0e68909 drivers: net: vsc9953: Add LAG support
You can now configure LAG on VSC9953's ports using the command:
ethsw [port <port_no>] aggr {[help] | show | <lag_group_no>}

A port must belong to a single LAG. By default, a port
belongs to a LAG equal to the port's number.

For each frame, a hash will be calculated based on
Source/Destination MAC addresses, Source/Destination IP(v4/v6)
addresses, Source/Destination ports. This hash will be used to
select a single egress port from LAG. This also assures
that frames from the same flow will always have the
same egress port.

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 12:22:19 -06:00
Codrin Ciubotariu
ba389e65e5 drivers: net: vsc9953: Fix FDB aging time
By default, the aging period is set to 0, so the dynamic
FDB entries are never removed. This patch sets the aging
time to 300 seconds.

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 12:22:08 -06:00
Stefan Agner
a058052c35 net: phy: do not read configuration register on reset
When doing a software reset, the reset flag should be written without
other bits set. Writing the current state will lead to restoring the
state of the PHY (e.g. Powerdown), which is not what is expected from
a software reset.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Michael Welling <mwelling@ieee.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 12:22:00 -06:00
Tom Rini
cd85bec36d Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-01-27 15:05:36 -05:00
Prabhakar Kushwaha
335b1936eb driver: net: fsl-mc: Remove portal id hard-coding
Management Complex firmware 9.0 has fixed the issue of
dprc_destroy_container i.e. the used portal is not return to the
free pool. Which was resulting in error ethernet driver want to
use this portal via either DPL or dynamically in Linux.

Hard-coding of portal id is removed.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:13:12 -08:00
Prabhakar Kushwaha
44b2036e12 driver: net: ldpaa: Add debug info of printing DPMAC stats
Add debug information prints to provide DPMAC statistics
 - Number of bytes received
 - Number of received and discard frames
 - Number of bytes transferred
 - Number of frames transferred
 etc.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:13:11 -08:00
Prabhakar Kushwaha
1c42beac80 driver: net: ldpaa: Increase num of buffers for a pool
Management Complex FW 9.0 set the hardware depletion to be 20
buffers in order to support multiple pools in DPNI. This requires
driver to fill the pool with at least 21 to be able to receive
frames. So, Increase number of buffers for a pool.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:13:11 -08:00
Prabhakar Kushwaha
6073548a0b driver: net: ldpaa: Report back only error frames for tx
Management Complex FW 9.0 puts a new requirement to provide Tx
confirmation and error queue configuration by calling
dpni_set_tx_conf API.

Configure report of only error frames for a tx frame.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:13:11 -08:00
Prabhakar Kushwaha
879a59ac90 driver: net: fsl-mc: Prepare extended cfg for DPNI create
Management Complex FW 9.0 puts a new requirement to prepare extended
parameters which should be provided as input in dpni_create. extended
parameters includes traffic class and IP reassembly configurations.

So prepare extended parameters with default "0" as input for
dpni_create.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:13:11 -08:00
Prabhakar Kushwaha
53e353fc3e driver: net: fsl-mc: flib changes for MC FW 9.0.0
MC firmware version 9.0.0 contains
 - Support of new APIs
 - Update in existing APIs
 - Change in Major and minor version of DPAA2 objects

This patch contains modifications in FLIB files to support new
MC firmware version.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:13:10 -08:00
Prabhakar Kushwaha
9a696f56fc driver: net: fsl-mc: Add version check for MC objects
Check and compare version of management  complex's object with
the version supported by Freescale ldpaa2 ethernet driver.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:13:10 -08:00
Ricardo Ribalda Delgado
21909baf57 net: xilinx_ll_temac: Fix string overflow
Size of this snprintf "lltemac.%lx" is bigger than 16 characters.
Replacing it with "ll_tem.%lx"

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:57:20 +01:00
Michal Simek
f17ea71d3a net: zynq: Change MDC setup for arm64
MDC setting depends on pclk input clocks which varies across SoC. This
driver is used by xilinx zynq and zynqmp SOC.
Input clock frequence on silicon is 125MHz where divider 64 put
frequency below 2.5MHz requires by spec (125/64=1.95).

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:54 +01:00
Michal Simek
0179063273 net: phy: ti: Enable automatic crossover mode
Enable automatic crossover cable detection.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27 15:55:54 +01:00
Michal Simek
3229c869aa net: emaclite: Move emaclite to Kconfig
Add PHYLIB and MII dependencies and enable it by default for Microblaze.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27 15:55:52 +01:00
Michal Simek
f412b6ab5b net: emaclite: Let core to handle received packet
Pass pointer to core to handle packet.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:52 +01:00
Michal Simek
f03ec01015 net: emaclite: Rename start and stop functions
Rename start and stop functions to align with DM functions names.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:52 +01:00
Michal Simek
d538ee1b54 net: emaclite: Move driver to DM
Move driver to DM.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27 15:55:52 +01:00
Michal Simek
4d2749be62 net: emaclite: Use indirect access in emaclite_recv
When IP is configured with pong buffers, IP is receiving packets to ping
and then to pong buffer and than ping again.
The original logic in the driver remains there that when ping buffer is
free, pong buffer is checked too and return if both are free.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:52 +01:00
Michal Simek
0070251836 net: emaclite: Use indirect reg access in send
The original logic in the driver was exchanging buffers which are used for
sending packet and tx_ping and tx_pong buffers were exchanged all the
time to ensure that IP has enough time to send the packet out.
Based on this "feature" send function was using nextbuffertouse variable
to save which buffer should be used.
Before this algorithm was called driver checked that there is free
buffer available.
This checking remains in the driver but driver tries to use tx_ping
first if available. If not, tx_pong buffer is used instead.
To reach this code the original condition is met that at least one of the
buffer should be available.
Testing doesn't show any performance drop when this patch is applied.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27 15:55:52 +01:00
Michal Simek
15c239c8ce net: emaclite: Remove XEL_TSR_XMIT_ACTIVE_MASK flag
This flag is not documented anywhere in the latest documentation that's
why this patch removes it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27 15:55:52 +01:00
Michal Simek
26c7945a24 net: emaclite: Fix logic around available TX buffers
Simplify logic how to find out if there is free TX buffer.
Both buffers are checked all the time that's why logic around order
can be removed.
Also add check when only one buffer is available.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27 15:55:52 +01:00
Michal Simek
5a4baa33e4 net: emaclite: Use indirect register access for TX reset
Move to use indirect register access when timeout expires for resetting
TX buffers.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27 15:55:52 +01:00
Michal Simek
3af709092c net: emaclite: Use indirect register access for rx_ping/pong
Do initialization via indirect register access.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:51 +01:00
Michal Simek
a0b2bfb0bf net: emaclite: Use indirect register access for tx_ping/pong
Do initialization via indirect register access.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27 15:55:51 +01:00
Michal Simek
9a23c49662 net: emaclite: Convert MDIO to use register offset
Use u-boot coding style how to setup and access MDIO bus.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27 15:55:51 +01:00
Michal Simek
d722e8641b net: emaclite: Add MDIO support to driver
Add MDIO support before move to DM.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27 15:55:51 +01:00
Michal Simek
8ce6947831 net: emaclite: Remove ancient OF probe function
Prepare for DM move.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27 15:55:51 +01:00
Michal Simek
338a5f2bf1 net: Add axi emac to Kconfig
Also add dependency on PHYLIB and MII which is required.
Clean PHYLIB dependency from the driver too.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27 15:55:51 +01:00
Michal Simek
ad499e42be net: axi_emac: Rename start, stop, write_hwaddr functions
Rename few functions to fit to the new name convention used by DM.

Suggested-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:51 +01:00
Michal Simek
97d2363d20 net: axi_emac: Split recv from free_pkt
Call net_process_received_packet() by core.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27 15:55:51 +01:00
Michal Simek
5d0449d4c7 net: axi_emac: Enable access to MDIO in probe
Detect phy when driver probes.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27 15:55:51 +01:00
Michal Simek
75cc93fad7 net: axi_emac: Move driver to DM
Move driver to DM.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27 15:55:51 +01:00
Michal Simek
f09854810c net: axi_emac: Pass private structure where possible
Use axidma_priv instead of ethdevice in preparation of the DM move.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:50 +01:00
Michal Simek
0d78abf5ba net: axi_emac: Pass private structure to phyread/phywrite
Prepare for move to DM.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27 15:55:50 +01:00
Michal Simek
6609f35b93 net: axi_emac: Put iobase to private structure
Saving iobase directly to private structure helps with moving to DM.
There is an option to load iobase from pdata but it is additional load.
Pointer to private structure is available all the time.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27 15:55:50 +01:00
Michal Simek
f36bbcceba net: axi_emac: Pass directly pointer to register space
Simplify mdio_wait function by passing regs directly.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27 15:55:50 +01:00
Michal Simek
2652a6219f net: axi_emac: Show phy address instead of register content
Fix debug message.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27 15:55:50 +01:00
Michal Simek
3e3f8ba26e net: axi_emac: Fix parentheses around operand !
Fix these compilation warning by proper grouping:
In function 'axi_dma_init': drivers/net/xilinx_axi_emac.c:391:7:
warning: suggest parentheses around operand of '!' or change '&' to '&&'
or '!' to '~' [-Wparentheses]
    if (!(in_be32(&priv->dmatx->control) |
        ^
In function 'axiemac_send': drivers/net/xilinx_axi_emac.c:501:21:
warning: suggest parentheses around operand of '!' or change '&' to '&&'
or '!' to '~' [-Wparentheses]
  while (timeout && (!in_be32(&priv->dmatx->status) &

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27 15:55:50 +01:00
Gregory CLEMENT
75b03cf14c net: macb: Not all the GEM are gigabit capable
During the initialization of PHY the gigabit bit capable is set if the
controller is a GEM. However, for sama5d2 and sama5d4, the GEM is
configured to support only 10/100.

Improperly setting the GBE capability leads to an unresponsive MAC
controller. This patch fixes this behavior allowing using the gmac with
these SoCs.

Suggested-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
[fixed minor checkpatch warning]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2016-01-27 13:58:58 +01:00
Pratiyush Mohan Srivastava
c088326597 drivers: net: fsl_mc: Compare pointer value qbman_swp_mc_start
Current code compares the return pointer of function
qbman_cena_write_start with NULL. Instead the value of the return
pointer should be compared.

Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Acked-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25 08:24:17 -08:00
Bin Meng
e6655d7c23 net: eepro100: Fix build warnings
When building katmai, it reports quite a lot

  warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]

Fix this by casting the dev->iobase with u_long.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-25 10:40:01 -05:00
Masahiro Yamada
84b8bf6d5d bug.h: move BUILD_BUG_* defines to include/linux/bug.h
BUILD_BUG_* macros have been defined in several headers.  It would
be nice to collect them in include/linux/bug.h like Linux.

This commit is cherry-picking useful macros from include/linux/bug.h
of Linux 4.4.

I did not import BUILD_BUG_ON_MSG() because it would not work if it
is used with include/common.h in U-Boot.  I'd like to postpone it
until the root cause (the "error()" macro in include/common.h causes
the name conflict with "__attribute__((error()))") is fixed.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-25 10:39:59 -05:00
Mateusz Kulikowski
e7138b34b0 net: zynq_gem: Use shared wait_for_bit
Use existing library function to poll bit(s).
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
2016-01-25 10:39:50 -05:00
Daniel Schwierzeck
df50b3b414 net: pcnet: refactor mapping of virtual addresses to physical ones
pci_virt_to_mem() uses virt_to_phys() to get the physical address.
But pci_virt_to_mem() is also called with uncached addresses which
is wrong according to the documentation of virt_to_phys().

Refactor the PCI_TO_MEM() macro to optionally map an uncached address
back to a cached one before calling pci_virt_to_mem().

Currently pcnet works because virt_to_phys() is incorrectly implemented
on MIPS. With the upcoming asm header file update for MIPS, the
virt_to_phys() implementation will be fixed. Thus this patch is needed
to keep pcnet working on MIPS Malta board.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-01-16 21:06:46 +01:00
Ben Whitten
192bc6948b Fix GCC format-security errors and convert sprintfs.
With format-security errors turned on, GCC picks up the use of sprintf with
a format parameter not being a string literal.

Simple uses of sprintf are also converted to use strcpy.

Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-14 22:11:34 -05:00
Tom Rini
f46c25583a Merge git://www.denx.de/git/u-boot-marvell
Conflicts:
	arch/arm/Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-01-14 11:23:05 -05:00
Stefan Roese
e3b9c98a23 net: mvneta: Convert to driver model
Update this driver to support driver model. As all MVEBU boards using
this driver are converted with this patch, the non-driver-model code
can be removed completely. This is also the reason why this patch
is quite big and includes a) the driver change and b) the
platform change. As its not git-bisect save otherwise.

With this conversion, some parameters are now extracted from the
DT instread of using the config header defines. The supported
properties right now are:

PHY-mode ("phy-mode") and PHY-address ("reg").

The base addresses for the ethernet controllers can be removed from
the header files as well.

Please note that this patch also removes the E1000 network driver
from some MVEBU config headers. This is necessary, as with DM_ETH
configured and the e1000 driver enabled, the PCI driver also needs
to support DM. But the MVEBU PCI(e) driver still needs to get
ported to DM. When this is done, the E1000 driver can be enabled
again.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Simon Glass <sjg@chromium.org>
2016-01-14 14:08:59 +01:00
Vladimir Zapolskiy
79206c04a9 net: lpc32xx: fix ignored MDIO busy wait status on read
The change fixes PHY write operation, which incorrectly waits for
released busy state before issuing a write operation, this breaks
sequential write/read operation logic, because read operation
starts immediately on request and it completes, when busy state is
gone.

Instead of adding the second preceding busy state check to read
function, do busy state release check after issuing a write operation,
this method of operation is also recommended by the LPC32xx User's
Manual, see MII Mgmt Indicators Register notes:

  For PHY Write if scan is not used:
  1. Write 0 to MCMD
  2. Write PHY address and register address to MADR
  3. Write data to MWTD
  4. Wait for busy bit to be cleared in MIND

Reported-by: Alexandre Messier <amessier@tycoint.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Alexandre Messier <amessier@tycoint.com>
2016-01-13 21:05:25 -05:00
Stephen Warren
7c4213f6a5 block: pass block dev not num to read/write/erase()
This will allow the implementation to make use of data in the block_dev
structure beyond the base device number. This will be useful so that eMMC
block devices can encompass the HW partition ID rather than treating this
out-of-band. Equally, the existence of the priv field is crying out for
this patch to exist.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-13 21:05:18 -05:00
Tom Rini
774da4b9aa Merge git://git.denx.de/u-boot-net 2016-01-13 21:05:16 -05:00
Simon Glass
552ddbe3ce dm: net: Convert rtl8169 to use DM PCI API
Update this driver to use the proper driver-model PCI API functions.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-12 10:19:09 -07:00
Simon Glass
21ccce1ba5 dm: pci: Add a dm_ prefix to pci_get_bdf()
Most driver model PCI functions have a dm_ prefix. At some point, when the
old code is converted to driver model and the old functions are removed, we
will drop that prefix.

For consistency, we should use the dm_ prefix for all driver model
functions. Update pci_get_bdf() accordingly.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12 10:19:09 -07:00
Tom Rini
b685c7348c Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-01-08 10:18:18 -05:00
Joe Hershberger
c5a75339cf net: Fix delay in net_retry test
Introduced in 45b4773 (net/arp: account for ARP delay, avoid duplicate packets on timeout)

Check the arp timeout and adjust the timeout start time before the call
to eth_recv() so that the sandbox driver has the opportunity to adjust
the sandbox timer after the new start time has been recorded.

Also, change the adjustment amount by 11 seconds instead of exactly the
10 seconds that the ping timout is expecting since the timeout check is
looking for the time elapsed to be greater than but not equal to the
specified delay.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Simon Glass <sjg@chromium.org>
2016-01-07 12:18:58 -07:00
Fabio Estevam
d584c68ce0 phy: atheros: Use ar8035_config for AR8031
Commit 08ad9b068a (" ar8031: modify the config func of ar8031 to
ar8021_config") selected 'ar8021_config' as the configuration function
for AR8031.

The correct would be to use 'ar8035_config' instead as AR8031/AR8035
have the same programming model and even share the same phy driver
in the linux kernel: drivers/net/phy/at803x.c.

Tested on a mx6qsabresd and wandboard, which now can work without
any PHY setup code in the board files.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-07 17:46:47 +01:00
Miao Yan
a40b2dff7b net: e1000: use correct helper to do endianness conversion
In struct e1000_rx_desc, field 'length' is declared as
uint16_t, so use le16_to_cpu() to do endianness conversion.

Also drop conversion on 'status' which is declared as
uint8_t.

Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-04 12:25:35 -05:00
Tom Rini
f1993ca066 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-01-03 10:32:24 -05:00
Måns Rullgård
845a57b4de net: fec_mxc: unregister mdio bus on probe error
If fecmxc_initialize_multi() fails, it frees but does not unregister
the mdio bus, causing subsequent uses of the "mii" command to crash.
Fix this by adding mdio_unregister() calls where needed.

Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
2016-01-03 15:28:06 +01:00
Måns Rullgård
843a3e5893 net: fec_mxc: configure MDIO hold time
If the host clock frequency is higher than 100 MHz, the MDIO hold
time needs to be increased from its current setting of one cycle in
order to meet the specified minium of 10 ns.  Writing an appropriate
value to the HOLDTIME field of the MII_SPEED register achieves this.

Comment copied from Linux kernel.

Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
2016-01-03 15:26:06 +01:00
Marek Vasut
2b26109219 net: designware: Zap trailing backslash
Trailing backslashes are necessary only in macros, not in the actual
code, so remove them.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2015-12-22 04:42:27 +01:00
Thomas Chou
25af71c4bf net: eth_designware: select PHYLIB in Kconfig
Select PHYLIB in drivers/net/Kconfig. And remove CONFIG_PHYLIB
from legacy board header files.

This fixed the warnings when both ALTERA_TSE and ETH_DESIGNWARE
are selected.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reported-by: Pavel Machek <pavel@denx.de>
Acked-by: Chin Liang See <clsee@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Tested-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-12-22 04:42:27 +01:00
Bin Meng
140bc33e05 net: e1000: Mark _disable_wr() and _write_status() as __maybe_unused
Per the comments, e1000_spi_eeprom_disable_wr() and
e1000_spi_eeprom_write_status() have been tested.
Remove the #if 0, #endif and mark them as __maybe_unused.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-12-21 20:01:57 -06:00
Bin Meng
c65a5f4f7f net: e1000: Remove CONFIG_MVBC_1G
CONFIG_MVBC_1G is not referenced anywhere, hence remove it.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-12-21 20:00:53 -06:00
Bin Meng
e97f7fbba5 net: e1000: Remove dead codes wrapped by #if 0
Remove those dead codes wrapped by #if 0 and #endif.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-12-21 19:59:34 -06:00
Marek Vasut
22854bda80 net: phy: micrel: Configure KSZ9021/KSZ9031 skew from OF
Add code to process the KSZ9021/KSZ9031 OF props if they are present
and configure skew registers based on the information from the OF.
This code is only enabled if the DM support for ethernet is also
enabled.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>

V2: - Implement struct ksz90x1_reg_field to describe the skew register
      fields more accurately.
    - Fix RXDV/TXEN skew register default value and offset.
2015-12-20 03:36:49 +01:00
Michal Simek
7bccc75a2b net: gem: Add driver dependencies to PHYLIB
Clear driver dependecies via Kconfig. Remove PHYLIB dependency from
the driver.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-12-18 13:15:58 +01:00
Michal Simek
c942810787 net: gem: Fix typo in Kconfig entry
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-12-18 13:15:58 +01:00
Michal Simek
9d9211ac11 net: gem: Separate recv and free_pkt functions
Use core to call net_process_received_packet() instead of call inside
the driver.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-12-18 13:15:58 +01:00
Michal Simek
da872d7c13 net: gem: Fix return value from recv
recv function should return 0 instead of frame_len not to
proceed the same packet again in core.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-12-18 13:15:58 +01:00
Michal Simek
bcdfef7a26 net: gem: Setup default phy address to -1
Undefined phy address is -1 not 0.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-12-18 13:15:58 +01:00
Shaohui Xie
ea1332ceb4 net: fm: disables unused FM1-DTSEC1 MAC node in DTS
We don't disable unused FM1-DTSEC1 MAC node in FMAN v2 since it is
used by MDIO. For FMAN v3, MDIO uses dedicated controller, so we
can disable unused FM1-DTSEC1 MAC node to avoid being probed in
Linux.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
[York Sun: revised commit message]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-17 08:52:19 +08:00
Mingkai Hu
862d9296dd armv8/ls1043a: remove print info
Remove verbose message for FMan port.

Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
[York Sun: Added commit message]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-17 08:52:18 +08:00
Stuart Yoder
509356224b driver: net: fsl-mc: remove MC firmware version check
The MC version numbers provide no meaningful information
about binary interface compatibility, so remove the
check which refuses to start the MC unless a specific
version is found.

Version checking is supposed to be done at the individual
object level, and individual drivers are responsible
for their own version checking.

Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Acked-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-17 08:52:18 +08:00
Tom Rini
b1f6be5ac8 qbman_portal.c: Update BUG_ON() call in qbman_swp_mc_submit
With gcc-5.x we get a warning about the ambiguity of BUG_ON(!a != b) and
becomes BUG_ON((!a) != b).  In this case reading of the function leads to
us wanting to rewrite this as BUG_ON(a != b).

Cc: Prabhakar Kushwaha <prabhakar@freescale.com>
Cc: Geoff Thorpe <Geoff.Thorpe@freescale.com>
Cc: Haiying Wang <Haiying.Wang@freescale.com>
Cc: Roy Pledge <Roy.Pledge@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-13 18:27:29 -08:00
Michal Simek
b8de29feae net: gem: Enable CTRL+C in wait_for_bit
Enable to break waiting loop at any time.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-12-07 10:14:29 +01:00
Michal Simek
596e5782e7 net: gem: Move gem to Kconfig
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-12-07 10:14:28 +01:00
Michal Simek
3cdb1450de net: gem: Read information about interface from DT
Do not set interface via configs. Read information from DT.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-12-07 10:14:28 +01:00
Michal Simek
6889ca7198 net: gem: Move driver to DM
- Enable DM_ETH by default for Zynq and ZynqMP
- Remove board_eth_init code
- Change miiphy_read function to return value instead of error code
  based on DM requirement
- Do not enable EMIO DT support by default

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-12-07 10:14:22 +01:00
Michal Simek
5a9284f7f5 net: gem: Fix miiphy_read name
Sync it with write function.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-12-07 09:59:05 +01:00
Michal Simek
687d731263 net: gem: Remove zynq_gem_of_init()
This function was used for OF init before DM.
Remove this function as the part of move to DM.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-12-07 09:59:05 +01:00
Michal Simek
c8e29271b1 net: gem: Enable MDIO bus earlier
Enable access to MDIO before zynq_gem_init is called.
It enables read information about phy earlier.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-12-07 09:59:05 +01:00
Michal Simek
90c6f2e21b net: gem: Check if priv->phydev is valid
Check return value.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-12-07 09:59:05 +01:00
Michal Simek
68cc3bd8b2 net: gem: Extract phy init code
Move phy init code out of zynq_gem_init. DM drivers are normally calling
this code from probe function.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-12-07 09:59:04 +01:00
Michal Simek
64a7ead64b net: gem: Remove phydev variable
Resort code to use priv->phydev variable directly.
It will simplify move to DM.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-12-07 09:59:04 +01:00
Michal Simek
f2fc27684f net: gem: Change mii function not to use eth_device structure
Next step to move driver to driver model. Do not use eth_device
structure. Use private structure instead.
Add iobase to private structure to store gem iobase.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-12-07 09:59:04 +01:00
Michal Simek
3fac27243c net: gem: Change mdio_wait prototype to pass regs
Pass regs instead of dev because this will be chagned by
driver model.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-12-07 09:59:04 +01:00
Michal Simek
b904725a11 net: gem: Do not continue if phy is not found
Add return value for phy detection algorithm to stop init function when
phy is not found.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-12-07 09:59:04 +01:00