This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_IS_IN_ENV
CONFIG_CONSOLE_MUX
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Re-order, re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>
Move these option to Kconfig and tidy up existing uses.
The Power PC boards don't have a suitable common element: the common header
files don't appear to line up with the Kconfig files as far as I can tell.
This results in a lot of defconfig changes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
[trini: Re-migrate, update common/console.c logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
Hardware: CM-FX6 Module from Compulab
This patch fixes unwanted watchdog resets while the user enters
a command at the U-Boot prompt.
As found on the CM-FX6 board from Compulab, when having enabled the
watchdog, a missing WATCHDOG_RESET call in common/console.c causes
this and alike boards to reset when the watchdog's timeout has
elapsed while waiting at the U-Boot prompt.
Despite the user could press several keys within the watchdog
timeout limit, the while loop in cli_readline.c, line 261, does only
call WATCHDOG_RESET if first == 1, which gets set to 0 in the 1st
loop iteration. This leads to a watchdog timeout no matter if the
user presses keys or not.
Although, this affects other boards as well as it touches
common/console.c, the macro WATCHDOG_RESET expands to {} if watchdog
support isn't configured. Hence, there's no harm caused and no need to
surround it by #ifdef in this case.
* Symptom:
U-Boot resets after watchdog times out when in commandline prompt
and watchdog is enabled.
* Reasoning:
When U-Boot shows the commandline prompt, the following function
call stack is executed while waiting for a keypress:
common/main.c:
main_loop => common/cli.c: cli_loop() =>
common/cli_hush.c:
parse_file_outer => parse_stream_outer =>
parse_stream => b_getch(i) =>
i->get(i) => file_get =>
get_user_input => cmdedit_read_input =>
uboot_cli_readline =>
common/cli_readline.c:
cli_readline => cli_readline_into_buffer =>
cread_line => getcmd_getch (== getc) =>
common/console.c:
fgetc => console_tstc
common/console.c:
(with CONFIG_CONSOLE_MUX is set)
- in console_tstc line 181:
If dev->tstc(dev) returns 0, the global tstcdev variable doesn't get
set. This is the case if no character is in the serial buffer.
- in fgetc(int file), line 297:
Program flow keeps looping because tstcdev does not get set.
Therefore WATCHDOG_RESET is not called, as mx_serial_tstc from
drivers/serial/serial_mxc.c does not call it.
* Solution:
Add WATCHDOG_RESET into the loop of console_tstc.
Note: Macro expands to {} if not configured, so no #ifdef is needed.
* Comment:
Signed-off-by: Christian Storm <christian.storm@tngtech.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Andreas J. Reichel <Andreas.Reichel@tngtech.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move SYS_OS_BASE to Kconfig and cleanup existing
uses.
Signed-off-by: Heiko Schocher <hs@denx.de>
[trini: Also migrate a4m2k]
Signed-off-by: Tom Rini <trini@konsulko.com>
The signature for this macro has changed. Bring in the upstream version and
adjust U-Boot's usages to suit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update to drivers/power/pmic/palmas.c:
Signed-off-by: Keerthy <j-keerthy@ti.com>
Change-Id: I6cc9021339bfe686f9df21d61a1095ca2b3776e8
These have now landed upstream. The naming is different and in one case the
function signature has changed. Update the code to match.
This applies the following upstream commits by
Thierry Reding <treding@nvidia.com> :
604e61e fdt: Add functions to retrieve strings
8702bd1 fdt: Add a function to get the index of a string
2218387 fdt: Add a function to count strings
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes devicetree nodes and or properties are added out of the u-boot
console, maybe through some script or manual interaction.
The devicetree as loaded or embedded is quite small, so the devicetree
has to be resized to take up those new nodes/properties.
In original the devicetree was only extended by effective
4 * add_mem_rsv.
With this commit we can add an argument to the "fdt resize" command,
which takes the extrasize to be added.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Simon Glass <sjg@chromium.org>
Create a Kconfig entry for DISPLAY_BOARDINFO and make it be the default
in certain architectures. Migrate all config files.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Create a Kconfig entry for DISPLAY_CPUINFO and make it be the default
in certain architectures. Migrate all config files.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This is already called earlier, from fdtdec_setup(), so drop this unnecessary
call from the init sequence.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present all video devices are probed on start-up. It would be better to
probe a device only when it is needed. This can happen if it is referenced
in the stdout environment variable, for example.
Add support for this by searching for a suitable device when needed, probing
it, and finding the stdio device it creates.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
By default saveenv option is not supported for SPL. This patch
enable the support for save environment variable for SPL build.
Enable save environment support in SPL after setenv. By default
the saveenv option is not provided in SPL, but some boards need
this support in 'Falcon' boot, where SPL need to boot from
different images based on environment variable set by OS. For
example OS may set "reboot_image" environment variable to
"recovery" inorder to boot recovery image by SPL. The SPL read
"reboot_image" and act accordingly and change the reboot_image
to default mode using setenv and save the environemnt.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Simon Glass <sig@chromium.org>
change in v1:
- dropped SUPPORT, use CONFIG_SPL_SAVEENV
- updates the comments in mmc_private.h
When CONFIG_SILENT_CONSOLE is defined and the default environment has
silent=1 it is not possible for a user to make the console un-silent if
the environment is not available when console_init_f() is called (for
example because the environment is in SPI).
Add a new helper function console_update_silent() and call it from both
console_init_f() and console_init_r().
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix various misspellings of:
* deprecated
* partition
* preceding,preceded
* preparation
* its versus it's
* export
* existing
* scenario
* redundant
* remaining
* value
* architecture
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
There is no need for this to be in the BSS region. By moving it we can delay
use of BSS in SPL. This is useful for machines where the BSS region is not
in writeable space. On 64-bit x86, SPL runs from SPI flash and it is easier
to eliminate BSS use than link SPL to run with BSS at a particular
cache-as-RAM (CAR) address.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update the fat loader to avoid using the spl_image global variable.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update the ext loader to avoid using the spl_image global variable.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Rather than having a global variable, pass the spl_image as a parameter.
This avoids BSS use, and makes it clearer what the function is actually
doing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code. Update existing users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code. We need two variants - one for BOOT_DEVICE_CPGMAC and one for
BOOT_DEVICE_USBETH.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code. Also set up the sunxi function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
All the other SPL loaders are in this directory, so move the SPI one in
there too.
There are two board-specific SPI loaders (fsl and sunxi). These remain in
the drivers/mtd/spi directory, since they do not contain generic code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Include updating the DFU case]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a linker list macro which can be used to declare an SPL image loader.
Update spl_load_image() to search available loaders for the correct one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present some spl_xxx_load_image() functions take a parameter and some
don't. Of those that do, most take an integer but one takes a string.
Convert this parameter into a struct so that we can pass all functions the
same thing. This will allow us to use a common function signature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move this option to Kconfig and tidy up existing uses. Also add a function
comment to the header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Instead of using the global spl_image variable, pass the required struct in
as an argument.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Instead of using the global spl_image variable, pass the required struct in
as an argument.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Rather than act on the global variable, pass the required struct in as a
parameter.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This format can be flashed directly at address 0 of
the NAND FLASH, as it contains all necessary headers.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Move FASTBOOT_MBR_NAME and FASTBOOT_GPT_NAME into Kconfig.
Add dependency on the FASTBOOT_FLASH setting (also for FASTBOOT_MBR_NAME).
Remove the now redundant GPT_ENTRY_NAME.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Add FIXME about xxx_PARTITION needing to be in Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add special target "mbr" (otherwise configurable via CONFIG_FASTBOOT_MBR_NAME)
to write MBR partition table.
Partitions are now searched using the generic function which finds any
partiiton by name. For MBR the partition names hda1, sda1, etc. are used.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
So far partition search by name has been supported only on the EFI partition
table. This patch extends the search to all partition tables.
Rename part_get_info_efi_by_name() to part_get_info_by_name(), move it from
part_efi.c into part.c and make it a generic function which traverses all part
drivers and searches all partitions (in the order given by the linked list).
For this a new variable struct part_driver.max_entries is added, which limits
the number of partitions searched. For EFI this was GPT_ENTRY_NUMBERS.
Similarly the limit is defined for DOS, ISO, MAC and AMIGA partition tables.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Steve Rae <steve.rae@raedomain.com>
This bug appears in b6396403 which makes u-boot unable to pass
arguments via bootm to a standalone application without this patch.
Steps to reproduce.
Compile a u-boot. Use mkimage to package the standalone hello_world.bin
file.
e.g. For the MIPS Boston platform
mkimage -n "hello" -A mips -O u-boot -C none -T standalone \
-a 0xffffffff80200000 -d hello_world.bin \
-ep 0xffffffff80200000 hello_out
Then tftp hello_out and run it using
boston # dhcp 192.168.154.45:hello_out
...
boston # bootm $loadaddr 123 321
Without the patch the following output is observed.
boston # bootm $loadaddr 123 321
Image Name: hello
Image Type: MIPS U-Boot Standalone Program (uncompressed)
Data Size: 1240 Bytes = 1.2 KiB
Load Address: 80200000
Entry Point: 80200000
Verifying Checksum ... OK
Loading Standalone Program ... OK
Example expects ABI version 8
Actual U-Boot ABI version 8
Hello World
argc = 0
argv[0] = "0xffffffff88000000"
With the patch, you see the following.
boston # bootm $loadaddr 123 321
Image Name: hello
Image Type: MIPS U-Boot Standalone Program (uncompressed)
Data Size: 1240 Bytes = 1.2 KiB
Load Address: 80200000
Entry Point: 80200000
Verifying Checksum ... OK
Loading Standalone Program ... OK
Example expects ABI version 8
Actual U-Boot ABI version 8
Hello World
argc = 3
argv[0] = "0xffffffff88000000"
argv[1] = "123"
argv[2] = "321"
argv[3] = "<NULL>"
Without the patch, the go command at the entry point seems to work.
boston # go 0xffffffff80200000 123 321
Example expects ABI version 8
Actual U-Boot ABI version 8
Hello World
argc = 3
argv[0] = "0xffffffff80200000"
argv[1] = "123"
argv[2] = "321"
argv[3] = "<NULL>"
Hit any key to exit ...
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Without this, if g_dnl_register() fails, DFU code continues on
blindly and crashes. This fix makes it simply print an error
message instead.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
[l.majewski@samsung.com - some manual tweaks needed]
