This driver is actually used for powerpc and m68k/ColdFire.
On ColdFire SoC's, interrupt flag get not set if IIEN flag (mbcr bit6,
interrupt enabled) is not set appropriately before each transfert.
As a result, the transfert hangs forever waiting for IIEN.
This patch set IIEN before each transfert, while considering this fix
as not harming powerpc arch.
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
- improve tegra DC driver to work with panel ops and implement
native 180 degree panel rotation support
- add T30 support to tegra DC driver
- add DSI driver (based on mainline Linux one with minor
adjustments, only T30 tested)
- add get_display_timing ops to simple panel driver
- extend simple panel driver to use it for MIPI DSI panels
which do not require additional DSI commands for setup
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCZDBwUw4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXL3+AJ9EkQKAWXZtlYdAOVl4/nzJnuTCAQCfY58zkDsw
TnAlwmMGWFl3RF6yGXY=
=uYUp
-----END PGP SIGNATURE-----
Merge tag 'video-20230407' of https://source.denx.de/u-boot/custodians/u-boot-video
- fix building sandbox without SDL
- improve tegra DC driver to work with panel ops and implement
native 180 degree panel rotation support
- add T30 support to tegra DC driver
- add DSI driver (based on mainline Linux one with minor
adjustments, only T30 tested)
- add get_display_timing ops to simple panel driver
- extend simple panel driver to use it for MIPI DSI panels
which do not require additional DSI commands for setup
Adds support for both DSI outputs found on Tegra. Only very
minimal functionality is implemented, so advanced features
like ganged mode won't work. Driver is heavily based on
mainline Tegra DSI and re-uses much of its features.
Only T30 is supported for now but T20 support can be added
if any supported devices will be found.
Driver is wrapped as panel driver since Tegra DC driver supports
only panel drivers calls.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF600T T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # HTC One X T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Internal video devices like DSI and HDMI controllers
require sending commands into DC register field.
To make this available, lets create platform data,
which is restricted to pass DC regmap only to
pre-defined devices.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF T30
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # Paz00
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101 T20
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # HTC One X T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
On popular request make the display driver from T20 work on T30 as
well. Turned out to be quite straight forward. However a few notes
about some things encountered during porting: Of course the T30 device
tree was completely missing host1x as well as PWM support but it turns
out this can simply be copied from T20. The only trouble compiling the
Tegra video driver for T30 had to do with some hard-coded PWM pin
muxing for T20 which is quite ugly anyway. On T30 this gets handled by
a board specific complete pin muxing table. The older Chromium U-Boot
2011.06 which to my knowledge was the only prior attempt at enabling a
display driver for T30 for whatever reason got some clocking stuff
mixed up. Turns out at least for a single display controller T20 and
T30 can be clocked quite similar. Enjoy.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF T30
Tested-by: Jonas Schwöbel <jonasschwoebel@yahoo.de> # Surface RT T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
This is currently broken. If SDL is not installed, SANDBOX_SDL becomes
false and build errors are generated, e.g.:
test/dm/video.c:424: undefined reference to `sandbox_sdl_set_bpp'
Fix it by making the function return an error in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add board code for R8A779G0 V4H White Hawk board.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Synchronize configuration symbols which are now switched to Kconfig
Mallocate gd->bd->bi_boot_params, i.e. drop the assignment
Sort headers, use clrbits_le32(), use BIT macros where appropriate
Use CONFIG_SYS_CLK_FREQ for counter frequency instead of custom macro]
Add Kconfig entry and PRR ID to support R8A779G0 V4H SoC.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update commit message]
Add DTs for R8A779G0 V4H White Hawk CPU and BreakOut boards.
Based on Linux next 20230228 DTs up to
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tho Vu <tho.vu.wh@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228, update commit message
Rename DTs to match Linux, which has dash between white-hawk]
Add R8A779G0 V4H DT extras for U-Boot.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update compatible string to match latest upstream]
Add initial DT support for R8A779G0 (R-Car V4H). Based on Linux next
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228, update commit message]
Add board code for R8A779F0 S4 Spider board.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Synchronize configuration symbols which are now switched to Kconfig
Mallocate gd->bd->bi_boot_params, i.e. drop the assignment
Sort headers, use clrbits_le32(), use BIT macros where appropriate
Use CONFIG_SYS_CLK_FREQ for counter frequency instead of custom macro]
Add Kconfig entry and PRR ID to support R8A779F0 S4 SoC.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update commit message]
Add DTs for R8A779F0 S4 Spider CPU boards and Breakout boards.
Based on Linux next 20230228 DTs up to
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228, update commit message]
Add R8A779F0 S4 DT extras for U-Boot.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update compatible string to match latest upstream]
Add initial DT for R8A779F0 S4 SoC. Based on Linux next
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228, update commit message]
This adds R-Car Generation 4 (Gen4) support as Renesas ARM64 SoC.
In this version, reusing R-Car Gen3 lowlevel initialize routine [1]
and R-Car Gen3 memory map tables [2] .
[1] arch/arm/mach-rmobile/lowlevel_init_gen3.S
[2] arch/arm/mach-rmobile/memmap-gen3.c
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: - Enable DTO support by default
- Sort the Kconfig lists
- Select RCAR_64 Kconfig option to pull in all the shared
Kconfig options with Gen3, and use where applicable to
deduplicate entries.
- Fix reference [2] typo in commit message
- Drop config options moved to Kconfig, rename rest to CFG_
accordingly to synchronize with upstream changes. Drop
removed CONFIG_VERY_BIG_RAM.
- Move board size limit to arch/Kconfig
- Move GICR_BASE to headers instead of common config]
The assembly for __gnu_thumb1_case_si was taken from upstream gcc and adapted
as width suffix was removed for the add instruction [1].
Signed-off-by: Francis Laniel <francis.laniel@amarulasolutions.com>
Tested-by: Tony Dinh <mibodhi@gmail.com>
[1] 4f181f9c7e/libgcc/config/arm/lib1funcs.S (L2156)
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Tony Dinh <mibodhi@gmail.com>
Tag the serial nodes with bootph-all in order to have these nodes and
the drivers available before relocation.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sync the serial nodes of the LX2160A based boards with their
representation in Linux. We also imported the clockgen and sysclk nodes
which are dependencies.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move the serial nodes under the soc node. No changes are made to the
nodes, just their location is changed.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The u-boot dts for these boards do not have an soc node, unlike its
Linux counterpart. This patch just adds the soc node as seen in Linux,
the next patches will move some nodes under it.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tag the serial nodes with bootph-all in order to have these nodes and
the drivers available before relocation.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sync the serial nodes of the LS1088A based boards with their
representation in Linux. We also imported the clockgen and sysclk nodes
which are dependencies.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move the serial nodes under the soc node. No changes are made to the
nodes, just their location is changed.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The u-boot dts for these boards do not have an soc node, unlike its
Linux counterpart. This patch just adds the soc node as seen in Linux,
the next patches will move some nodes under it.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Beacon Embedded has an i.MX8M Plus development kit which consists
of a SOM + baseboard. The SOM includes Bluetooth, WiFi, QSPI, eMMC,
and one Ethernet PHY. The baseboard includes audio, HDMI, USB-C Dual
Role port, USB Hub with five ports, a PCIe slot, and a second Ethernet
PHY. The device trees are already queued for inclusion in Linux 6.3.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for Data Modul i.MX8M Plus eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, SPI NOR, USB.
Signed-off-by: Marek Vasut <marex@denx.de>
Add WDT reboot bindings on DH i.MX6 DHSOM to permit the platform
to reboot via WDT in U-Boot. These are custom U-Boot bindings,
hence they are placed in -u-boot.dtsi .
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
U-Boot can be booted from NAND without SPL by prepending the DCD header to
the actual U-Boot binary. However this requires prepending 1024 bytes to
u-boot.imx (DCD + u-boot.bin).
There is already a similar target to build spl/u-boot-nand-spl.imx, add the
same option for no-SPL boot.
Tested on i.MX6ULL.
The resulting layout of u-boot-nand.imx is:
- Offset 0x0000 (0 KiB): padding
- Offset 0x0400 (1 KiB): DCD header
- Offset 0x1000 (4 KiB): u-boot.bin
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
J721e SK has been broken since at least March 2022.
The main-navss and mcu-navss nodes were renamed and this caused the
A72 SPL to fail early in the boot even before the serial port was
enabled. Fix this.
A later patch series between v2022.07 and v2022.10 additionally broke
boot on this board by introducing hbmc nodes which are not present on
this board. The right fix is to disable these by default in the SOC
dtsi file, but for now we can also disable them in the u-boot dtsi.
With both these fixed, we can now boot the j721e SK board fully from
mainline u-boot.
Fixes: 58d61fb5a7 ("arm: dts: k3-j721e-sk: Add initial A72 specific dts support")
Fixes: 297daac43a ("arm: dts: k3-j721e-mcu-wakeup: Add HyperBus Controller node")
Reported-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
[gadiyar@ti.com: update commit description]
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Bryan Brattlof <bb@ti.com>
Originally, the mmc aliases node was present in imx6qdl-pico.dtsi.
After the sync with Linux in commit d0399a46e7 ("imx6dl/imx6qdl:
synchronise device trees with linux"), the aliases node is gone as
the upstream version does not have it.
This causes a boot regression in which the eMMC card cannot be found anymore.
Fix it by passing the alias node in the u-boot.dtsi file to
restore the original behaviour where the eMMC (esdhc3) was
mapped to mmc0.
Fixes: d0399a46e7 ("imx6dl/imx6qdl: synchronise device trees with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
The image size was increased but the firmware-update part was not
updated. Correct this so that VBE firmware update can succeed with
sandbox_vpl.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 85c66dc95c ("sandbox: Expand size for VPL image")
---------------------------------
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/15819
i.MX patches queued for next:
- Conversions to DM_SERIAL
- Fixes for Toradex boards
- Gateworks Boards
- i.MX8ULP
- EQoS support / fixes, changes in boards
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCZCaU0Q8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76YCKgCgk4OueoIggmes+Ccj8bu1BcQbrfYAoJAgMeKE
It0hrVAifD62TPb2rmHt
=hFVG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-next-20230331' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx into next
u-boot-imx-next-20230331 for next
---------------------------------
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/15819
i.MX patches queued for next:
- Conversions to DM_SERIAL
- Fixes for Toradex boards
- Gateworks Boards
- i.MX8ULP
- EQoS support / fixes, changes in boards
The FEC interface mode is now configured in common board_interface_eth_init()
and called by FEC MAC driver when appropriate. Drop the board side duplicates
if the same functionality.
Signed-off-by: Marek Vasut <marex@denx.de>
The EQoS interface mode is now configured in common board_interface_eth_init()
and called by EQoS MAC driver when appropriate. Drop the board side duplicates
if the same functionality.
Signed-off-by: Marek Vasut <marex@denx.de>
The assigned-clock no longer have to be dropped, the clock are now
defined in clk-imx8mp.c and used by DWMAC driver to configure the
DWMAC clock. Drop the workarounds from U-Boot specific DT extras.
Signed-off-by: Marek Vasut <marex@denx.de>
In order for i2c_num==4 and 5 to stay invalid for non-imx8mp SOCs, the
i2c_ccgr[] array must be sized by the number of initializers present,
not with a hard-coded 6 which would implicitly initialize the last two
elements with zeroes.
Also, the bounds check is off-by-one.
Fixes: c92c3a4453 "ARM: imx: imx8mp: Enable support for i2c5 and i2c6 on i.MX8MP"
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Implement common board_interface_eth_init() and call it from the FEC
driver to configure IOMUXC GPR[1] register according to the PHY mode
obtained from DT. This supports all three interface modes supported by
the i.MX8M Mini/Nano/Plus FEC and supersedes the current board-side
configuration of the same IOMUX GPR[1] duplicated in the board files.
Signed-off-by: Marek Vasut <marex@denx.de>
Implement common board_interface_eth_init() and call it from the DWMAC
driver to configure IOMUXC GPR[1] register according to the PHY mode
obtained from DT. This supports all three interface modes supported by
the i.MX8M Plus DWMAC and supersedes current board-side configuration
of the same IOMUX GPR[1] duplicated in the board files.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
The DWMAC clock in i.MX8M Plus were so far configured via ad-hoc
architecture code. Replace that with DM clock instead. This way,
the driver claims all its required clock, enables and disables
them, and even gets the CSR clock rate and sets the TX clock rate,
without any need of architecture specific register fiddling. Drop
the architecture specific code while at it too.
The adjustment here is modeled after STM32MP15xx clock handling
in this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
