The node names should be generic and DT schema expects certain pattern:
xilinx/zynqmp-zcu100-revC.dtb: leds: 'vbus-det' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221125144136.477171-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Michal Simek <michal.simek@amd.com>
cdns prefix was deprecated and replaced by xlnx one in upstream Linux. Also
U-Boot driver has been updated to support new compatible string that's why
it is time to remove it and deprecate it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
AM62A7-SK board has 4GB LPDDR4 Micron MT53E2G32D4DE-046 AUT:B part
but only 2GB was enabled early.
Enable full 4GB memory by updating the latter 2GB memory region
which gets mapped to 0x0880000000 i.e. DDR16SS0_SDRAM as referred in
Table 2-1. AM62A Common SoC Memory of AM62Ax TRM [1].
[1] : https://www.ti.com/lit/zip/spruj16
Logs: https://gist.github.com/devarsht/e85b6af89c01ddadb3a62f3e5f196af8
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Synchronize devicetree sources with Linux v6.2.
- Use GIC interrupt definitions
- Add reg properties in USB-glue and SoC-glue node
- Fix node names to follow the generic names list in DT specification
- Add L2 cache and AHCI nodes
- Update nand and pcie nodes
- And some trivial fixes
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Marek Vasut <marex@denx.de>
UniPhier DT applies its own USB node for U-Boot due to the USB driver
constrains. After solving this issue, u-boot allows the original USB node.
After switching USB node, synchronization of USB node with Linux becomes
possible.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Marek Vasut <marex@denx.de>
Default parent clock for the PWM on Tegra is a 32kHz clock and
is unable to support the requested PWM period.
Fix PWM support on Tegra20, Tegra30, Tegra114, Tegra124 and Tegra210 by
updating the parent clock for the PWM to be the PLL_P.
This commit is equivalent to Linux kernel commit:
https://lore.kernel.org/all/20221010100046.6477-1-jonathanh@nvidia.com/
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF T30
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101 T20
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # ASUS TF201 T30
Tested-by: Thierry Reding <treding@nvidia.com> # T30 and T124
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Tom <twarren@nvidia.com>
Add devicetree for chameleonv3 with the 270-2I2-D11E variant of the
Mercury+ AA1 module
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This file is included by the different chameleonv3 variants. Change the
name to .dtsi.
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Set the bitstream name per Chameleon variant. This allows the same
boot filesystem with all bitstream variants to be used on different
boards.
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
i2c updates for v2023.04
- add new i2c driver ast2600 from Ryan Chen
- i2c-cdns: make read fifo-depth configurable through device tree
from Pei Yue Ho
- mxc i2c driver: print base address in hex, not in decimal
from Fabio
When DM_SERIAL is enabled, the device-tree tag u-boot,dm-pre-reloc is
required for this board to boot over UART with kwboot. Enable this in
kirkwood-pogoplug-series-4-u-boot.dtsi.
Added by Stefan while applying:
Please note that it's not fully understood, why this property really
is needed. Here a link to the discussion about this:
https://lore.kernel.org/r/20230201080210.ypz4nrj4y2igwxz3@pali/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Synology DS116 is a NAS based on Marvell Armada 385 SoC.
Board Specification:
- Marvel MV88F6820 Dual Core at 1.8GHz
- 1 GiB DDR3 RAM
- 8MB Macronix mx25l6405d SPI flash
- I2C
- 2x USB 3.0
- 1x GBE LAN port (PHY: Marvell 88E1510)
- 1x SATA (6 Gbps)
- 3x LED
- PIC16F1829 (connected to uart1)
- GPIO fan
- serial console
Note that this patch depends on the add-support for Thecus N2350 patch:
https://patchwork.ozlabs.org/project/uboot/patch/20230201231306.7010-1-mibodhi@gmail.com/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
The i2c driver have global register that i2c bus use
ofnode_get_parent to get parent register address.
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Previously, the TX LED would flash but nothing would appear on the
serial port, and the board would appear dead with a build of the
socfpga_cyclone5_defconfig. I have verified that adding the frequency to
the uart will fix the serial console on my board.
Thanks to @ehoffman on the Rocketboards forum:
https://forum.rocketboards.org/t/cyclonev-programming-fpga-from-u-boot/2230/30
Signed-off-by: Jade Lovelace <lists@jade.fyi>
Reviewed-by: Marek Vasut <marex@denx.de>
Use standard pinconf drive-strength values from Linux DT bindings rather
than ones based on custom u-boot header. These changes are in direction
to make u-boot DTs for Qcom SoCs to be compatible with standard Linux
DT bindings.
Also, add support for pinconf bias-pull-up.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
As MDIO driver does not support Driver Model, the
pinctrl settings in the MDIO node will not
be applied resulting in PHY not being detected.
To workaround this we add the MDIO pinctrl in
the CPSW3G node in the -u-boot.dtsi file.
Add the missing MDIO and RGMII pinctrl nodes in
k3-am642-r5-evm.dts
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add MV88E61XX DSA support:
- update dt to provide internal MDIO bus and port handles.
U-Boot requires a more restrictive subset of the dt bindings
required by Linux for the sake of simplifying code
- update defconfig to remove old driver and enable new one
- replace mv88e61xx_hw_reset weak override with board_phy_config support
for register configuration that is outside the scope of the DSA driver
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Synchronize R-Car device trees with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
The following script has been used for the synchronization:
$ for i in $(cd arch/arm/dts/ ; ls -1 r8a* | grep -v 'u-boot.dts' ; sed -n '/#include/ s@.*"\(.*\)"@\1@p' $(ls -1 r8a* | grep -v 'u-boot.dts')) ; do
if [ -e /linux-2.6/arch/arm64/boot/dts/renesas/$i ] ; then
cp /linux-2.6/arch/arm64/boot/dts/renesas/$i arch/arm/dts/ ;
elif [ -e /linux-2.6/arch/arm/boot/dts/$i ] ; then
cp /linux-2.6/arch/arm/boot/dts/$i arch/arm/dts/
else
echo "NOT FOUND: $i"
fi
done
$ git add $( ( cd arch/arm/dts/ ; ls -1 r8a* | grep -v 'u-boot.dts' ; sed -n '/#include/ s@.*"\(.*\)"@\1@p' $(ls -1 r8a* | grep -v 'u-boot.dts')) | tr " " "\n" | sed 's@^@arch/arm/dts/@g' )
Move the include/dt-bindings/{clk,clock}/versaclock.h header used by
the renesas boards to match Linux 6.1.y as well.
Keep arch/arm/dts/r8a774c0-u-boot.dtsi sdhi3 node as it is now used
by the arch/arm/dts/r8a774c0-cat874.dts board.
Pick s@spi-flash@flash@ change in arch/arm/dts/r8a779a0-falcon-u-boot.dts
from "ARM: dts: Synchronize R-Car V3U DTs with Linux 5.18.3" .
Adjust R8A77990 Ebisu CONFIG_SYS_MMC_ENV_DEV from 2 to 0 to reflect
the card enumeration in ebisu.dtsi /aliases DT node .
Adjust R8A7795 and R8A7796 ULCB CONFIG_SYS_MMC_ENV_DEV from 1 to 0 to
reflect the card enumeration in ulcb.dtsi /aliases DT node .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com> # r8a779a0-falcon-u-boot.dts
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> # r8a779a0-falcon-u-boot.dts
NXP tested imx8mn-ddr4 with firmware version 201810 only. Use this
version for all imx8mn targets with DRAM DDR4.
Fixes: 93c4c0e4dd ("arm: dts: imx8mn-u-boot: Create common imx8mn-u-boot.dtsi")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Fabio Estevam <festevam@denx.de>
In some situations the GSC firmware where the EEPROM containing the
model and DRAM configuration may not be ready by the time the SoC
is ready to talk to it over I2C.
Instead of a hard delay, poll the I2C lines to wait until they are
released to avoid the I2C drivers 'Arbitation lost' error message.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add I2C GPIO bus recovery support by adding scl-gpios and sda-gpios for the
various I2C busses on Gateworks Venice boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Synchronizing the device tree with linux introduced a regression.
The U-Boot specific dtsi mustn't override the alias settings for
the eMMC/SD interfaces.
Without this U-Boot cannot access the eMMC and boot the kernel.
Fixes: c21b61bff1 ("colibri-imx6ull/-emmc: synchronise device tree with linux")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
In case U-Boot itself if the PSCI provider on i.MX8M, do not
require the ATF BL31 blob, as at that point the blob is useless
and would interfere with U-Boot operation.
Signed-off-by: Marek Vasut <marex@denx.de>
In commit d0399a46e7, the device tree was
synchronized from linux and the aliases were dropped.
They need to be kept so that the mmc cards are in the right order.
Without the aliases, u-boot reports:
MMC: FSL_SDHC: 2, FSL_SDHC: 3
With the aliases, u-boot reports:
MMC: FSL_SDHC: 0, FSL_SDHC: 1
The upstream linux device tree does not contain the same aliases than
u-boot (It keeps the devices order with /dev/mmcblk2 and /dev/mmcblk3).
Because this board has been using different aliases in u-boot
and linux, a imx6q-sabrelite-u-boot.dtsi file is added to be
automatically included in imx6q-sabrelite.dts.
This way, linux and u-boot each keep their own aliases and there
is no breakage on current installations.
This should never be done for new boards as we want to keep linux and
u-boot with the same aliases as much as possible.
This patch is only necessary to avoid breaking existing setups.
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The property fsl,mux_mask is deleted by commit ed7bda5 (imx8ulp:
synchronise device tree with linux). This causes the pinctrl
driver not work on 8ULP, so fail to print any log.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The changes of commit 6a21c69521 ("arm: dts: imx8mp: add of-list
support to common imx8mp-u-boot.dtsi") breaks the loading of the fip.
This commit fixes the break by modify the configuration properly.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
assign a label for config-SEQ so that the board dts can modify
the configuration more easily.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add the board support for the i.MX8MM Cloos PHG board.
This board uses a imx8mm-tqma8mqml SoM from TQ-Group.
imx8mm-phg.dts and imx8mm-tqma8mqml.dtsi are taken
directly from Linux 6.2-rc3.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add aliases for the RTCs on the board and on the SoC. This ensures that
the primary RTC is always the one on the board that has a buffered supply
and maximum accuracy.
This is a direct port of the pending commit from linux-next.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Originally, the mmc aliases node was present in imx6qdl-sabresd.dtsi.
After the sync with Linux in commit d0399a46e7 ("imx6dl/imx6qdl:
synchronise device trees with linux"), the aliases node is gone as
the upstream version does not have it.
This causes a regression in which the SD card cannot be found anymore.
Fix it by passing the alias node in the u-boot.dtsi file to
restore the original behaviour where the SD card (esdhc3) was
mapped to mmc1.
Fixes: d0399a46e7 ("imx6dl/imx6qdl: synchronise device trees with linux")
Reported-by: Carlos Rafael Giani <dv@pseudoterminal.org>
Signed-off-by: Fabio Estevam <festevam@denx.de>
This reverts commit f5315dd629.
[why]
TPL is not mandatory for not all Rockchip SoCs, some SoCs like
RK356x, and RK3588 still use mainline u-boot without TPL as
their ddr init programs are accessed via binaries provided by
Rockchip instead of ddr source code.
Marking TPL build makes it not able to build u-boot.itb on
RK356x targets so revert this so that it can build an SPL build
that would support all across Rockchip platforms.
Suggested-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Tested-by: Anand Moon <linux.amoon@gmail.com> # CM3
Add pinctrl's for high speed eMMC and MMC cards.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
In case the CONFIG_IMX8M_LPDDR4 and CONFIG_IMX8M_DDR4 options are both
disabled (i. e. BSH boards), binmain fails because DDR4 bin files are
missing.
Fixes: 93c4c0e4dd ("arm: dts: imx8mn-u-boot: Create common imx8mn-u-boot.dtsi")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
ODROID-N2L is a variant SBC in small form factor and some peripherals
are removed from ODROID-N2PLUS based on S922X SoC.
- On-board ethernet is removed
- On-board RTC is removed
- USB 3.0 hub is removed, so one USB 2.0 and one USB 3.0 host ports
are available
- Huge heatsink is replaced with 40x40mm heatsink, 5V active heatsink
is recommended or a tall passive sink is optional
- 3.5mm earjack is removed
- IR remote receiver is removed
- MIPI DSI port is added
It doesn't use the odroid-n2 board support since ADC revision
collides with Odroid-N2+ and since it doesn't have on-board ethernet
no need to load the MAC address from eFuses.
Link: https://lore.kernel.org/r/20230126-u-boot-odroid-n2l-v1-2-c60f695e0f6c@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
