To be able to use the tool binman on sandbox,
the config SANDBOX should imply BINMAN.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This does not use driver model and is more than two years past the
migration date. Drop it.
It can be added back later if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Drop the Kconfigs which are not used and all references to them. In
particular, this drops CONFIG_VIDEO to avoid confusion and allow us to
eventually rename CONFIG_DM_VIDEO to CONFIG_VIDEO.
Also drop the prototype for video_get_info_str() which is no-longer used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
Unfortunately this driver uses the old video structure to store things.
This is not supported with driver model.
Drop the old code and comment out the other pieces, so the maintainer can
take a look.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current approach for setting the environment variables that
describe the memory layout runs the risk of overlapping with
reserved memory regions. Use the lmb code to derive the addresses
for these variables instead.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The firmware on larger NVMe drives needs more than 100ms to come up.
Change the timeout to 1s.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit f11513d997 ("net: phy: realtek: Add tx/rx delay config for
8211e") made the Realtek PHY driver honour the phy-mode DT property,
to set up the proper delay scheme for the RX and TX lines. A similar
change in the kernel revealed that those properties were mostly wrong.
The kernel DTs got updated over the last few months, but we were missing
out on the U-Boot version.
Just sync in the phy-mode properties from the mainline kernel,
v5.17-rc7, to avoid the breaking DT sync that late in the cycle.
This fixes Ethernet operation on the affected boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Commit 5bc4cd05d7 ("sunxi: move non-essential code out of s_init()")
moved the call to eth_init_board() from s_init() into board_init_f().
This means it's now only called from the SPL, which makes sense for
most of the other moved low-level functions. However the GMAC pinmux and
clock setup in eth_init_board() was not happy about that, so it broke
the sun7i GMAC.
Since Ethernet is of no use in the SPL anyway, just move the call into
board_init(), which is only run in U-Boot proper.
This fixes Ethernet operation for the A20 SoCs, which broke in
v2022.04-rc1, with the above mentioned commit.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Petr Štetiar <ynezz@true.cz> [a20-olinuxino-lime2]
Add the PWM node and enable it for AST2600 EVB
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
This patchs add the signal description array for PWM pinctrl settings.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Replace old macros PCI_CLASS_CODE_COMM and PCI_CLASS_SUB_CODE_COMM_SERIAL
by new macros defined in pci_ids.h. Old macros would be deleted in followup
commit.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This adds a separate CONFIG_CC_OPTIMIZE_FOR_SPEED option in a choice,
in preparation for adding another optimization option. Also convert SH's
makefile to use this new option.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_FAULT_ECHO_LINK_DOWN
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AT91_WANTS_COMMON_PHY
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Commit 0934dddc64 ("arm: a37xx: Update DTS files to version from
upstream Linux kernel") ported Linux's device-tree files for Armada 3720
SOCs. This broke SPI support on some Espressobin boards and results in
following U-Boot error:
Loading Environment from SPIFlash... jedec_spi_nor flash@0: unrecognized JEDEC id bytes: f7, 30, 0b
*** Warning - spi_flash_probe_bus_cs() failed, using default environment
Before that commit DT node for SPI was called 'spi-flash@0' and after
that commit it is called 'flash@0'. Before that commit 'spi-max-frequency'
was set to 50000000 and after it is 104000000.
Rename DT node 'spi-flash@0 in armada-3720-espressobin-u-boot.dtsi to
'flash@0' and set custom U-Boot 'spi-max-frequency' back to 50000000.
With this change SPI is working on Espressobin again and it is detected
with JEDEC ids ef, 60, 16 on our tested unit.
Loading Environment from SPIFlash... SF: Detected w25q32dw with page size 256 Bytes, erase size 4 KiB, total 4 MiB
OK
Note that it is unknown why spi-max-frequency with value 104000000 does not
work in U-Boot as it works fine with Linux kernel. Also note that in
defconfig file configs/mvebu_espressobin-88f3720_defconfig is set option
CONFIG_SF_DEFAULT_SPEED=40000000 which is different value than in DT.
Fixes: 0934dddc64 ("arm: a37xx: Update DTS files to version from upstream Linux kernel")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Commit 0934dddc64 ("arm: a37xx: Update DTS files to version from
upstream Linux kernel") ported Linux's device-tree files for Armada 3720
SOCs. This broke USB port on Turris MOX, because in Linux' DTS the bus
voltage supply is described as a `phy-supply` property of connector
node, a mechanism that is not supported in U-Boot yet.
For now, fix this by adding `vbus-supply` to usb3 node.
Fixes: 0934dddc64 ("arm: a37xx: Update DTS files to version from upstream Linux kernel")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
various minor sandbox improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmI1URkRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYglAf/eM5MtohjWDBQUyvPiQTIV0iS5Zu7NV7Z
1qkrv4OuwZ+U3djtusP7VIUnmdnQlwbF1fFZzo+JUmtYg59K6ZvgI/S+oJzr17/D
bMh+8FpDggEjJhzwSM5fdImfE1PLp161zUxTWMH25VmB+yxQMGWqZBQls+0GADN5
jT4dGwTn098a2HLvdAqkNwafY0Q1cUQeYg8z2J3gdDdZos2PdQV3TqjbrAS6Pr+Z
jAZV+TfTkU2rk6S7B34Ojzx2dF8e80sRK/o/2/+60kt+dUO+nfS/evOb1kqfj8dx
ULNXEBjS1aMy7Z6TCg/E3uEZLM5xyaTZKTwiNeKMthmOK8ZQ3boRuA==
=9FkF
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-18mar22' of https://source.denx.de/u-boot/custodians/u-boot-dm into next
binman FIT improvements
various minor sandbox improvements
If state is not being written, but RAM is, we should still show a message,
so it is clear that this is happening.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_ATMEL_LEGACY
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AT91_GPIO_PULLUP
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AT91SAM9260
CONFIG_AT91SAM9G20
CONFIG_AT91SAM9XE
CONFIG_AT91SAM9261
CONFIG_AT91SAM9263
CONFIG_AT91SAM9G45
CONFIG_AT91SAM9M10G45
CONFIG_AT91SAM9N12
CONFIG_AT91SAM9RL
CONFIG_AT91SAM9X5
CONFIG_SAM9X60
CONFIG_SAMA7G5
CONFIG_SAMA5D2
CONFIG_SAMA5D3
CONFIG_SAMA5D4
These options are already select'd as needed, so we're just cleaning up
files here.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AM335X_USB0
CONFIG_AM335X_USB0_MODE
CONFIG_AM335X_USB1
CONFIG_AM335X_USB1_MODE
We do this by introducing specific options for static configuration of
USB0/USB1 in SPL rather than defining CONFIG_AM335X_USBx_MODE to the
enum value being used. Furthermore, with how the code is used now we do
not need to have OTG mode exposed as an option here, so remove that.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts removes the following symbols:
CONFIG_HAS_ETH0
CONFIG_HAS_ETH1
CONFIG_HAS_ETH2
CONFIG_HAS_ETH3
This is because at this point, only the ids8313 platform was using the
code which was controlled by these symbols. In turn, this code already
performs error checking on being able to perform the device tree fixup.
Rather than convert these to Kconfig for a single platform, update the
code to not need these checks and remove them from all the platforms
they were unused on.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ARMV8_SWITCH_TO_EL1
Cc: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
This converts the following to Kconfig:
CONFIG_ARMV7_SECURE_BASE
CONFIG_ARMV7_SECURE_MAX_SIZE
CONFIG_ARMV7_SECURE_RESERVE_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
U-Boot can be chainloaded from vendor firmware on ARM64 chromebooks from
a GPT partition (roughly the same as in doc/chromium/chainload.rst), but
an appropriate image header must be built-in to the U-Boot binary by
enabling LINUX_KERNEL_IMAGE_HEADER.
This header has a field for an image load offset from 2MiB alignment
which must also be customized through LNX_KRNL_IMG_TEXT_OFFSET_BASE.
Set it equal to SYS_TEXT_BASE by default for Rockchip boards, which
happens to make this offset zero and works fine on chromebook_kevin
both for chainloading and bare-metal use.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for Kevin, an RK3399-based convertible chromebook that is
very similar to Bob. This patch is mostly based on existing support for
Bob, with only minor changes for Kevin-specific things.
Unlike other Gru boards, coreboot sets Kevin's center logic to 925 mV,
so adjust it here in the dts as well. The rk3399-gru-kevin devicetree
has an unknown event code reference which has to be defined, set it
to the Linux counterpart. The new defconfig is copied from Bob with the
diffconfig:
DEFAULT_DEVICE_TREE "rk3399-gru-bob" -> "rk3399-gru-kevin"
DEFAULT_FDT_FILE "rockchip/rk3399-gru-bob.dtb" -> "rockchip/rk3399-gru-kevin.dtb"
VIDEO_ROCKCHIP_MAX_XRES 1280 -> 2400
VIDEO_ROCKCHIP_MAX_YRES 800 -> 1600
+TARGET_CHROMEBOOK_KEVIN y
With this Kevin can boot from SPI flash to a usable U-Boot prompt on the
display with the keyboard working, but cannot boot into Linux for
unknown reasons.
eMMC starts in a working state but fails to re-init, microSD card works
but at a lower-than-expected speed, USB works but causes a hang on
de-init. There are known workarounds to solve eMMC and USB issues.
Cc: Marty E. Plummer <hanetzer@startmail.com>
Cc: Simon Glass <sjg@chromium.org>
[Alper: commit message, resync config with Bob, update MAINTAINERS,
add to Rockchip doc, add Kconfig help message, set regulator]
Co-developed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This adds some devicetree settings for the Gru-based boards, based on
what works on a Kevin board.
Gru-based boards usually have an 8MiB SPI flash chip and boot from it.
Make the u-boot.rom file intended to be flashed on it match its size.
Add properties for booting from SPI, and only try to boot from SPI as
MMC and SD card don't seem to work in SPL yet.
The Chromium OS EC needs a delay between transactions so it can get
itself ready. Also it currently uses a non-standard way of specifying
the interrupt. Add these so that the EC works reliably.
The Rockchip Embedded DisplayPort driver is looking for a rockchip,panel
property to find the panel it should work on. Add the property for the
Gru-based boards.
The U-Boot GPIO controlled regulator driver only considers the
"enable-gpios" devicetree property, not the singular "enable-gpio" one.
Some devicetree source files have the singular form as they were added
to Linux kernel when it used that form, and imported to U-Boot as is.
Fix one instance of this in the Gru boards' devicetree to the form that
works in U-Boot.
The PWM controlled regulator driver complains that there is no init
voltage set for a regulator it drives, though it's not clear which one.
Set them all to the voltage levels coreboot sets them: 900 mV.
The RK3399 SoC needs to know the voltage level that some supplies
provides, including one fixed 1.8V audio-related regulator. Although
this synchronization is currently statically done in the board init
functions, a not-so-hypothetical driver that does this dynamically would
query the regulator only to get -ENODATA and be confused. Make sure
U-Boot knows this supply is at 1.8V by setting its limits to that.
Most of this is a reapplication of commit 08c85b57a5 ("rockchip: gru:
Add extra device-tree settings") whose changes were removed during a
sync with Linux at commit 167efc2c7a ("arm64: dts: rk3399: Sync
v5.7-rc1 from Linux"). Apply things to rk3399-gru-u-boot.dtsi instead so
they don't get lost again.
Signed-off-by: Simon Glass <sjg@chromium.org>
[Alper: move to -u-boot.dtsi, rewrite commit message, add more nodes]
Co-developed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
microblaze:
- Add support for reserved memory
xilinx:
- Update FRU code with MAC reading
zynqmp:
- Remove double AMS setting
- DT updates (mostly for SOMs)
- Add support for zcu106 rev 1.0
zynq:
- Update nand binding
nand:
- Aligned zynq_nand to upstream DT binding
net:
- Add support for ethernet-phy-id
mmc:
- Workaround CD in zynq_sdhci driver also for ZynqMP
- Add support for dynamic/run-time SD config for SOMs
gpio:
- Add driver for slg7xl45106
firmware:
- Add support for dynamic SD config
power-domain:
- Update zynqmp driver with the latest firmware
video:
- Add skeleton driver for DP and DPDMA
i2c:
- Fix i2c to work with QEMU
pinctrl:
- Add driver for zynqmp pinctrl driver
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYjIBkgAKCRDKSWXLKUoM
IYUwAKCYRBxb59BFq4MRvTbNcRZ7H4oGIQCfVUl3x9KZ7nFZaYAaBXFBxwna+PE=
=irCR
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.07-rc1
microblaze:
- Add support for reserved memory
xilinx:
- Update FRU code with MAC reading
zynqmp:
- Remove double AMS setting
- DT updates (mostly for SOMs)
- Add support for zcu106 rev 1.0
zynq:
- Update nand binding
nand:
- Aligned zynq_nand to upstream DT binding
net:
- Add support for ethernet-phy-id
mmc:
- Workaround CD in zynq_sdhci driver also for ZynqMP
- Add support for dynamic/run-time SD config for SOMs
gpio:
- Add driver for slg7xl45106
firmware:
- Add support for dynamic SD config
power-domain:
- Update zynqmp driver with the latest firmware
video:
- Add skeleton driver for DP and DPDMA
i2c:
- Fix i2c to work with QEMU
pinctrl:
- Add driver for zynqmp pinctrl driver
Commit 0934dddc64 ("arm: a37xx: Update DTS files to version from
upstream Linux kernel") ported Linux's device-tree files for Armada 3720
SOCs. This broke network on Turris MOX, because the SOC's MDIO bus in
U-Boot currently isn't probed via DM as it's own device, but is
registered as part of mvneta's driver, which means that pinctrl
definitions are not parsed for the MDIO bus node. Also mvneta driver
does not consider "phy-handle" property, only "phy".
For now, fix this by adding armada-3720-turris-mox-u-boot.dtsi file
returning the MDIO to how it was defined previously.
A better solution (using proper mvmdio DM driver) is being work on, but
will need testing on various boards, and we need the bug fixed now for
the upcoming release.
Fixes: 0934dddc64 ("arm: a37xx: Update DTS files to version from upstream Linux kernel")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The Linux PLIC interrupt-controller driver actually initializes the hart
context registers in the PLIC driver exactly in the same order as
specified in the interrupts-extended device tree property. See the device
tree binding [1].
The ordering of the interrupts is therefore essential in order to
configure the PLIC correctly.
Fix the order so that we will have sane IRQ behavior when booting Linux
with the u-boot device tree.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/interrupt-controller/sifive,plic-1.0.0.yaml
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Linux kernel fpioa pinctrl driver expects the sysctl phandle and the
power bit offset of the fpioa device to be specified as a single
property "canaan,k210-sysctl-power".
Replace the "canaan,k210-sysctl" and "canaan,k210-power-offset"
properties with "canaan,k210-sysctl-power" to satisfy the Linux kernel
requirements. This new property is parsed using the existing function
dev_read_phandle_with_args().
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Linux drivers for many of the K210 peripherals depend on the power bus
clock to be specified. Add the missing clocks and their names to avoid
problems when booting Linux using u-boot DT.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
"kendryte" is the marketing name for the K210 RISC-V SoC produced by
Canaan Inc. Rather than "kendryte,k210", use the usual "canaan,k210"
vendor,SoC compatibility string format in the device tree files and
use the SoC name for file names.
With these changes, the device tree files are more in sync with the
Linux kernel DTS and drivers, making uboot device tree usable by the
kernel.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This patch configures U-Boot SPL for DHCOM SoM to permit DFU upload of
SPL and subsequent u-boot.itb for recovery or commissioning purposes.
The DFU usage procedure is identical to STM32MP1 DHCOR SoM, see commit
3919aa1722 ("ARM: dts: stm32: Add DFU support for DHCOR recovery") ,
except for switching the SoM into DFU mode. By default, the DHCOM SoM
has no dedicated mechanism for setting BOOTn straps into UART/USB mode,
therefore to enter DFU mode, the SoC must fail to boot from boot media
which can be selected by the BOOTn strap override mechanism first and
then fall back to DFU mode.
In case of a SoM with pre-populated BOOTn strap override button, power
the system off, remove microSD card (if applicable), hold down the BOOTn
strap override button located between eMMC and SoM edge connector, power
on the SoM. The SoC will fail to boot from SD card and fall back into
DFU mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Implement PSCI system suspend and placement of DRAM into SSR while the
CPUs are in suspend. This saves non-trivial amount of power in suspend,
on 2x W632GU6NB-15 ~710mW.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
