Commit graph

4200 commits

Author SHA1 Message Date
Poonam Aggrwal
87c7661b42 85xx: Added P1020 Processor Support.
P1020 is another member of QorIQ series of processors which falls in ULE
category. It is an e500 based dual core SOC.

Being a scaled down version of P2020 it has following differences:
- 533MHz - 800MHz core frequency.
- 256Kbyte L2 cache
- Ethernet controllers with classification capabilities.
Also the SOC is pin compatible with P2020

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-28 17:12:39 -05:00
Poonam Aggrwal
728ece343e 85xx: Add support for P2020RDB board
The code base adds P1 & P2 RDB platforms support.
The folder and file names can cater to future SOCs of P1/P2 family.
P1 & P2 processors are 85xx platforms, part of Freescale QorIQ series.

Tested following on P2020RDB:
1. eTSECs
2. DDR, NAND, NOR, I2C.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-28 17:12:38 -05:00
Poonam Aggrwal
0e870980a6 8xxx: Removed CONFIG_NUM_CPUS from 85xx/86xx
The number of CPUs are getting detected dynamically by checking the
processor SVR value.  Also removed CONFIG_NUM_CPUS references from all
the platforms with 85xx/86xx processors.

This can help to use the same u-boot image across the platforms.

Also revamped and corrected few Freescale Copyright messages.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-28 17:12:38 -05:00
Peter Tyser
bafdf9aa9d 85xx: Remove unused CONFIG_CLEAR_LAW0 defines
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-28 17:12:37 -05:00
Kumar Gala
337f9fde2e 85xx: Add a 36-bit physical configuration for MPC8536DS
We move all IO addressed (CCSR, localbus, PCI) above the 4G boundary
to allow for larger memory sizes.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-28 17:12:36 -05:00
Kumar Gala
ad19e7a5d2 pci/fsl_pci_init: Rework PCI ATMU setup to handle >4G of memory
The old PCI ATMU setup code would just mimic the PCI regions into the
ATMU registers.  For simple memory maps in which all memory, MMIO, etc
space fit into 4G this works ok.  However there are issues with we have
>4G of memory as we know can't access all of memory and we need to
ensure that PCICSRBAR (PEXCSRBAR on PCIe) isn't overlapping with
anything since we can't turn it off.

We first setup outbound windows based on what the board code setup
in the pci regions for MMIO and IO access.  Next we place PCICSRBAR
below the MMIO window.  After which we try to setup the inbound windows
to map as much of memory as possible.

On PCIe based controllers we are able to overmap the ATMU setup since
RX & TX links are separate but report the proper amount of inbound
address space to the region tracking to ensure there is no overlap.

On PCI based controllers we use as many inbound windows as available to
map as much of the memory as possible.

Additionally we changed all the CCSR register access to use proper IO
accessor functions.  Also had to add CONFIG_SYS_CCSRBAR_PHYS to some
86xx platforms that didn't have it defined.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-28 17:12:36 -05:00
Kumar Gala
8295b94400 pci/fsl_pci_init: Use PCIe capability to determine if controller is PCIe
Change the code to use the PCIe capabilities register to determine if we
are a PCIe controller or not.  Additionally cleaned up some white space
and formatting in the file.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-28 17:12:36 -05:00
Kumar Gala
cb151aa2cf pci/fsl_pci_init: Fold fsl_pci_setup_inbound_windows into fsl_pci_init
Every platform that calls fsl_pci_init calls fsl_pci_setup_inbound_windows
before it calls fsl_pci_init.  There isn't any reason to just call it
from fsl_pci_init and simplify things a bit.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-28 17:12:35 -05:00
Kumar Gala
fb3143b35e pci/fsl_pci_init: Fold pci_setup_indirect into fsl_pci_init
Every platform that calls fsl_pci_init calls pci_setup_indirect before
it calls fsl_pci_init.  There isn't any reason to just call it from
fsl_pci_init and simplify things a bit.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-28 17:12:35 -05:00
André Schwarz
28887d831b Use common code for Matrix Vision boards
Clean up existing boards (mvBC-P/MPC5200 and mvBL-M7/MPC8343) by
using common code.

Signed-off-by: Andr Schwarz <andre.schwarz@matrix-vision.de>
2009-08-28 00:31:23 +02:00
Wolfgang Denk
5928da0193 Merge branch 'next' of git://git.denx.de/u-boot-nand-flash into next 2009-08-28 00:17:41 +02:00
Kim Phillips
05f91a65ab mpc83xx: mpc8349itx - accommodate larger kernel sizes & unzero the bootdelay
apparently the ITX was missed last round.

Also make bootdelay consistent with other boards, so as to give on the
opportunity to fix mistakenly set bootcmd without having checked for an
bootdelay zero setting first.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-08-26 21:28:55 -05:00
Kim Phillips
cc861f7127 mpc83xx: match dtb filename references to their dts equivalents in the linux kernel
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-08-26 21:28:55 -05:00
Sandeep Paulraj
77b351cd0f NAND: DaVinci: V2 Adding 4 BIT ECC support
This patch adds 4 BIT ECC support in the DaVinci NAND
driver. Tested on both the DM355 and DM365.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-08-26 15:37:03 -05:00
Sandeep Paulraj
f83b7f9e8a MTD:NAND: ADD new ECC mode NAND_ECC_HW_OOB_FIRST
This patch adds the new mode NAND_ECC_HW_OOB_FIRST in the nand code to
support 4-bit ECC on TI DaVinci devices with large page (up to 2K) NAND
chips.  This ECC mode is similar to NAND_ECC_HW, with the exception of
read_page API that first reads the OOB area, reads the data in chunks,
feeds the ECC from OOB area to the ECC hw engine and perform any
correction on the data as per the ECC status reported by the engine.

This patch has been accepted by Andrew Morton and can be found at

http://userweb.kernel.org/~akpm/mmotm/broken-out/mtd-nand-add-new-ecc-mode-ecc_hw_oob_first.patch

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-08-26 15:37:03 -05:00
Sandeep Paulraj
a2c65b47ef NAND: ADD page Parameter to all read_page/read_page_raw API's
This patch adds a new "page" parameter to all NAND read_page/read_page_raw
APIs.  The read_page API for the new mode ECC_HW_OOB_FIRST requires the
page information to send the READOOB command and read the OOB area before
the data area.

This patch has been accepted by Andrew Morton and can be found at
http://userweb.kernel.org/~akpm/mmotm/broken-out/mtd-nand-add-page-parameter-to-all-read_page-read_page_raw-apis.patch

WE would like this to become part of the u-boot GIT as well

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-08-26 15:37:02 -05:00
Heiko Schocher
de4250929f 83xx, kmeter1: added NAND support
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-08-26 15:37:02 -05:00
Kyungmin Park
ecad289fc6 OneNAND: Remove unused read_spareram
Remove unused read_spareram and add unlock_all as kernel does

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-08-26 15:37:02 -05:00
Kyungmin Park
ce3277a6f2 OneNAND: Remove unused read_spareram
Remove unused read_spareram and add unlock_all as kernel does

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2009-08-26 22:06:50 +02:00
Eric Millbrandt
0d042037b3 galaxy5200: Cleanup typo and trailing whitespace
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
2009-08-26 21:33:27 +02:00
Wolfgang Denk
d7f4d14a8b Merge branch 'next' of git://www.denx.de/git/u-boot-coldfire into next 2009-08-26 21:29:32 +02:00
TsiChung Liew
88c811b153 ColdFire: Fix missing _IO_BASE which caused compile error
The compile error was caused by a recent patch. Affected platforms -
M5253DEMO.h, M5253EVBE.h, and M54455EVB.h. Adding the _IO_BASE
automatically defined to 0 in asm-m68k/io.h if it isn't set in
platform configuration file.

Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
2009-08-26 03:40:59 -05:00
Niklaus Giger
3a7b2c21fb Support up to 7 banks for ids as specified in JEDEC JEP106Z
see http://www.jedec.org/download/search/jep106Z.pdf
Add some second source legacy flash chips 256x8.

Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-08-26 08:58:27 +02:00
Wolfgang Denk
d3870bd2d8 Merge branch 'next' of git://git.denx.de/u-boot-net into next 2009-08-25 23:03:22 +02:00
Wolfgang Denk
68ccfa482b Merge branch 'master' into next 2009-08-25 22:57:10 +02:00
Wolfgang Denk
3d447d135c Merge branch 'master' of git://git.denx.de/u-boot-blackfin 2009-08-25 22:51:40 +02:00
Ben Warren
b1c0eaac11 Convert CS8900 Ethernet driver to CONFIG_NET_MULTI API
All in-tree boards that use this controller have CONFIG_NET_MULTI added
Also:
  - changed CONFIG_DRIVER_CS8900 to CONFIG_CS8900
  - changed CS8900_BASE to CONFIG_CS8900_BASE
  - changed CS8900_BUS?? to CONFIG_CS8900_BUS??
  - cleaned up line lengths
  - modified VCMA9 command function that accesses the device
  - removed MAC address initialization from lib_arm/board.c

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Tested-by: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
2009-08-25 13:35:54 -07:00
Alessandro Rubini
d47628a6ec arm nomadik: activate defrag choose 4k transfer block size
This chooses 4kB data size for both TFTP and NFS, as an example
about how to use support for IP fragments.

Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-08-25 13:35:54 -07:00
Albin Tonnerre
885fc78c28 Switch from per-driver to common definition of bin2bcd and bcd2bin
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Acked-by: Stefan Roese <sr@denx.de>
2009-08-25 12:57:55 +02:00
Albin Tonnerre
e84aba135e Replace BCD2BIN and BIN2BCD macros with inline functions
In the process, also remove backward-compatiblity macros BIN_TO_BCD and
BCD_TO_BIN and update the sole board using them to use the new bin2bcd
and bcd2bin instead

Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
2009-08-25 12:57:55 +02:00
Eric Millbrandt
5b53b29bc2 Add support for the galaxy5200
Add support for the DEKA Research and Development galaxy5200 board

The galaxy5200 is an Freescale mpc5200 based embedded industrial
control board.

Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
2009-08-25 12:57:55 +02:00
Mike Frysinger
0a9e4e7721 unify {CONFIG_,}ENV_IS_EMBEDDED
Some boards have fallen out of sync by defining CONFIG_ENV_IS_EMBEDDED
manually.  While it is useful to have this available to the build system,
let's do it automatically rather than forcing people to opt into it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-08-25 12:57:54 +02:00
Wolfgang Denk
30fc5cd311 include/s3c24x0.h: fix S3C24X0_SPI_CHANNEL declaration
The SPI controller on the S3C24X0 has 8 bit registers, not 32 bit.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-08-25 12:22:38 +02:00
Harald Krapfenbauer
c2fbcb6ae8 Blackfin: cm-bf527/cm-bf537: increase flash sectors
Newer revisions of these boards have slightly larger flashes, so increase
the configured number of sectors so that U-Boot works on all revisions.

Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-08-23 17:33:40 -04:00
Mike Frysinger
6ac9f47977 start a linker script helper file
Start a common header file for common linker script code (such as
workarounds for older linkers) rather than doing this in the build system.

As fallout, we no longer execute the linker every time config.mk is
included by a build file (which can easily be 70+ times), but rather only
execute it once.

This also fixes a bug in the major version checking by creating a macro to
easily compare versions and keep people from making the same common
mistake (forgetting to check major and minor together).

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-08-23 22:33:33 +02:00
Albin Tonnerre
79b91de958 include/mmc.h: Fix typo in IS_SD() macro
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
2009-08-23 22:11:30 +02:00
Wolfgang Denk
d52785d7f5 Merge branch 'master' of /home/wd/git/u-boot/custodians 2009-08-22 00:24:54 +02:00
Kim Phillips
79f516bccc mpc83xx: accommodate larger kernel sizes by default
linux mpc83xx_defconfig kernels are getting bigger, accommodate for
their growth by adjusting default load and fdt addresses.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-08-21 17:11:44 -05:00
Kim Phillips
8eceeb7fd6 mpc83xx: mpc8377erdb - change DDR settings to those from latest bsp
when using Linus' 83xx_defconfig, the mpc8377rdb would hang at boot
at either:

NET: Registered protocol family 16

or the

io scheduler cfq registered

message.  Fixing up these DDR settings appears to fix the problem.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-08-21 17:11:44 -05:00
Kim Phillips
27c5248dd4 mpc83xx: tqm8349 - remove pci & flash window conflict
commit 9993e196da "mpc83xx: convert all
remaining boards over to 83XX_GENERIC_PCI" remapped pci windows on
tqm834x to make it more consistent with the other 83xx boards.  During
that time however, the author failed to realize that FLASH_BASE was
occupying the same range as what PCI1_MEM_BASE was being assigned.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Wolfgang Denk <wd@denx.de>
2009-08-21 17:11:44 -05:00
Heiko Schocher
6d2c26ac83 mpc83xx: add missing CSCONFIG_ODT_WR_CFG for 832x CPUs
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-08-21 17:10:35 -05:00
Paul Gortmaker
193b4cb3f6 mpc83xx: mpc8349 - delete unused SYS_MID_FLASH_JUMP
This was introduced with the MPC8349EMDS board, and then copied to
a couple other boards by nature of being the reference implementation.

  u-boot$git grep CONFIG_SYS_MID_FLASH_JUMP
  include/configs/MPC8349EMDS.h:#define CONFIG_SYS_MID_FLASH_JUMP 0x7F000000
  include/configs/sbc8349.h:#define CONFIG_SYS_MID_FLASH_JUMP     0x7F000000
  include/configs/vme8349.h:#define CONFIG_SYS_MID_FLASH_JUMP     0x7F000000
  u-boot$

It currently isn't used, so delete it before it spreads further.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-08-21 17:10:04 -05:00
Paul Gortmaker
c0d660fbbe mpc83xx: sbc8349 - make enabling PCI more user friendly
Prior to this commit, to enable PCI, you had to go manually
edit the board config header, which isn't really user friendly.
This adds the typical PCI make targets to the toplevel Makefile
in accordance with what is being done with other boards.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-08-21 17:09:21 -05:00
Prafulla Wadaskar
11906936e1 arm: rd6281a: Fixed NAND specific warning
It is recommended to define the macro CONFIG_SYS_64BIT_VSPRINTF
for NAND specific warning removal, same is done in this patch

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2009-08-21 23:26:09 +02:00
Wolfgang Denk
9af019f579 Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx 2009-08-18 13:53:54 +02:00
Albin Tonnerre
918319c705 Update the mtd driver name in bootargs for at91-based boards
The name of the atmel nand driver in the kernel changed from at91_nand
to atmel_nand back in June 2008, but the at91-based boards config files
still refer to at91_nand. This patch updates them with the new name

Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
2009-08-18 13:51:51 +02:00
Ben Goska
8fa656aa52 omap3: Fixed a problem with hwecc
In commit 187af954cf there
was a typo that offset all the ecc registers by 4 bytes, fixed that.

Signed-off-by: Ben Goska <goskab@onid.oregonstate.edu>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
2009-08-18 13:51:30 +02:00
Stefan Roese
514bab6609 ppc4xx: Fix "chip_config" command for AMCC Arches
This patch fixes the "chip_config" command for I2C bootstrap EEPROM
configuration. First it changes the I2C bootstrap EEPROM address to
0x54 as this is used on Arches (instead of 0x52 on Canyonlands/
Glacier). Additionally, the NAND bootstrap settings are removed
for Arches since Arches doesn't support NAND-booting.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-08-18 09:16:33 +02:00
Wolfgang Denk
4af34177b6 Monahans: avoid floating point calculations
Current code for the Monahans CPU defined OSCR_CLK_FREQ as 3.250 (MHz)
which caused floating point operations to be used. This resulted in
unresolved references to some FP related libgcc functions when using
U-Boot's private libgcc functions.

Change the code to use fixed point math only.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-08-17 23:53:41 +02:00
Giuseppe CONDORELLI
dce3d79710 zlib: updated to v.1.2.3
This patch updates zlib to the latest stable version.
Only relevant zlib parts were ported to u-boot tree, as already did for the
current zlib (0.95). New zlib guarantees a faster inflate performances
other then others improvements as explained at www.zlib.net.
It also includes Alessandro Rubini's patches to allow 0 as destination pointer
and to call watchdog reset if required by architecture.

Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
Reviewed-by: Angelo Castello <angelo.castello@st.com>
Reviewed-by: Alessandro Rubini <rubini-list@gnudd.com>
2009-08-11 22:14:29 +02:00
Wolfgang Denk
f45c07dbd1 Merge branch 'master' of git://git.denx.de/u-boot-net 2009-08-11 21:44:55 +02:00
Po-Yu Chuang
750326e5d5 arm: A320: driver for FTMAC100 ethernet controller
This patch adds an FTMAC100 ethernet driver for Faraday A320 evaluation board.

Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-08-10 14:53:52 -07:00
Kumar Gala
f90dc43fd6 85xx: Removed BEDBUG support from FSL 85xx boards
For some reason the MPC8544 enabled BEDBUG if PCI was enabled and that
got copied int the MPC8536, MPC8572 and P2020 DS boards.  The BEDBUG
support has never been made to work completely on e500/85xx so we
just disable it to save space and match the other FSL 85xx boards.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-08-10 16:40:55 -05:00
Dirk Behme
cd3dcba142 OMAP3: Fix missing GPMC_CONFIG_CS0_BASE
Applying two indepenent OMAP3 patches resulted in missing
GPMC_CONFIG_CS0_BASE. Patch "omap3: embedd gpmc_cs into gpmc
config struct" removes GPMC_CONFIG_CS0_BASE, independent patch
"omap3: bug fix for NOR boot support" introduces it's usage.
Re-introduce GPMC_CONFIG_CS0_BASE.

Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-08-10 00:12:43 +02:00
Ilya Yanok
ba3dbaf281 mxc-mmc: sdhc host driver for MX2 and MX3 proccessor
This is a port of Linux driver for SDHC host controller hardware
found on Freescale's MX2 and MX3 processors. Uses new generic MMC
framework (CONFIG_GENERIC_MMC) and it looks like there are some
problems with a framework (at least on LE cpus). Some of these
problems are addressed in the following patches.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
2009-08-09 23:47:38 +02:00
Alessandro Rubini
642d7b63c3 kirkwood/gpio.h: remove duplicate definition
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
2009-08-09 23:46:45 +02:00
Prafulla Wadaskar
30951960ba arm: Sheevaplug: Fixed NAND specific warning
It is recommended to define the macro CONFIG_SYS_64BIT_VSPRINTF
for NAND specific warning removal, same is done in this patch

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2009-08-09 23:44:52 +02:00
Josh Boyer
317734966e Dual-license IBM code contributions
It was brought to our attention that U-Boot contains code derived from the
IBM OpenBIOS source code originally provided with some of the older PowerPC
4xx development boards.  As a result, the original license of this code has
been carried in the various files for a number of years in the U-Boot project.

IBM is dual-licensing the IBM code contributions already present in U-Boot
under either the terms of the GNU General Public License version 2, or the
original code license already present.

Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2009-08-09 23:15:33 +02:00
Detlev Zundel
ff27650bb2 digsy_mtc: Update default environment
Signed-off-by: Detlev Zundel <dzu@denx.de>
2009-08-09 23:01:41 +02:00
Mike Frysinger
bedd8403f7 export SPI functions to standalone apps
While we're here, fix the broken #ifdef handling in _exports.h.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-08-09 22:34:51 +02:00
Wolfgang Denk
81813cb01f Merge branch 'master' of git://git.denx.de/u-boot-net 2009-08-08 12:08:09 +02:00
Dirk Behme
a3d1421dfd omap3: use only fixed-size types inside ctrl_structs
replace variable types in ctrl_structs for omap3 by those with
fixed size (u8, u16, u32).
Additional ifndef-protection is needed by examples which do not
compile when including asm/types.h

Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-08-08 11:36:29 +02:00
Dirk Behme
97a099eaa4 omap3: remove typedefs for configuration structs
Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-08-08 11:33:23 +02:00
Roy Zang
aa0707897c Add Intel E1000 PCIE card support
Based on Intel PRO/1000 Network Driver 7.3.20-k2
  Add Intel E1000 PCIE card support. The following cards are added:
  INTEL_82571EB_COPPER
  INTEL_82571EB_FIBER,
  INTEL_82571EB_SERDES
  INTEL_82571EB_QUAD_COPPER
  INTEL_82571PT_QUAD_COPPER
  INTEL_82571EB_QUAD_FIBER
  INTEL_82571EB_QUAD_COPPER_LOWPROFILE
  INTEL_82571EB_SERDES_DUAL
  INTEL_82571EB_SERDES_QUAD
  INTEL_82572EI_COPPER
  INTEL_82572EI_FIBER
  INTEL_82572EI_SERDES
  INTEL_82572EI
  INTEL_82573E
  INTEL_82573E_IAMT
  INTEL_82573L
  INTEL_82546GB_QUAD_COPPER_KSP3
  INTEL_80003ES2LAN_COPPER_DPT
  INTEL_80003ES2LAN_SERDES_DPT
  INTEL_80003ES2LAN_COPPER_SPT
  INTEL_80003ES2LAN_SERDES_SPT

 82571EB_COPPER dual ports,
 82572EI single port,
 82572EI_COPPER single port PCIE cards
 and
 82545EM_COPPER,
 82541GI_LF
 pci cards are tested on both  P2020 board
 and MPC8544DS board.

 Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-08-08 02:26:05 -07:00
Mike Frysinger
86848a74c3 net: sync env ethaddr to device enetaddr in eth_init()
In the previous enetaddr refactoring, the assumption with commit 56b555a644
was that the eth layer would handle the env -> device enetaddr syncing.
This was not the case as eth_initialize() is called only once and the sync
occurs there.  So make sure the eth_init() function does the env -> device
sync with every network init.

Reported-by: Andrzej Wolski <awolski@poczta.fm>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-08-07 17:39:23 -07:00
Matthias Ludwig
187af954cf omap3: embedd gpmc_cs into gpmc config struct
Embedd chip select configuration into struct for gpmc config
instead of having it completely separated as suggested by
Wolfgang Denk on
http://lists.denx.de/pipermail/u-boot/2009-May/052247.html

Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>
2009-08-07 23:31:51 +02:00
Wolfgang Denk
cb32ed1fc2 Merge branch 'next' of git://git.denx.de/u-boot-coldfire 2009-08-04 21:54:11 +02:00
David Brownell
06bffc6ea5 rm9200 lowevel_init: don't touch reserved/readonly registers
For some reason the AT91rm9200 lowlevel init writes to a bunch of
reserved or read-only addresses.  All the boards seem to define the
value-to-be-written values as zero ... but they shouldn't actually
be writing *anything* there.

No documented erratum justifies these accesses.  It looks like maybe
some pre-release BDI-2000 setup code has been carried along by cargo
cult programming since at least late 2004 (per GIT history).

Here's a patch disabling what seems to be bogosity.  Tested on a
csb337; there were no behavioral changes.

Signed-off-by: David Brownell <david-b@pacbell.net>

on RM9200ek
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-08-03 09:26:26 +02:00
David Hunter
301b7db88f pxa: Fix typo in GCDR(x)
Fix a typo in the GCDR(x) macro. It's a good thing no one was using it.

Signed-off-by: David Hunter <hunterd42@gmail.com>
2009-08-01 16:06:26 +02:00
Stefan Roese
89bcc48750 ppc4xx: Add basic support for AMCC PPC460EX/460GT rev B chips
This patch is based on a diff created by Phong Vo from AMCC.

Signed-off-by: Phong Vo <pvo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-30 07:22:18 +02:00
Stefan Roese
27dd5f8e10 ppc4xx: amcc: Move "kernel_addr_r" etc to higher locations (> 16MB)
This patch moves the load addresses for kernel, fdt and ramdisk to higher
addresses (>= 16MB). This enables booting of bigger kernel images (e.g.
lockdep enabled).

Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-30 07:22:18 +02:00
Stefan Roese
6942efc2be ppc4xx: amcc: Set CONFIG_SYS_BOOTMAPSZ to 16MB for big kernels
This patch changes CONFIG_SYS_BOOTMAPSZ from 8MB to 16MB which is the
initial TLB on 40x PPC's in the Linux kernel. With this change even bigger
Linux kernels (> 8MB) can be booted.

This patch also sets CONFIG_SYS_BOOTM_LEN to 16MB (default 8MB) to enable
decompression of bigger images.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-30 07:22:18 +02:00
Wolfgang Denk
108f56b056 Merge branch 'master' of git://git.denx.de/u-boot-i2c 2009-07-30 00:36:25 +02:00
Kumar Gala
4c2e3da82d Update Freescale copyrights to remove "All Rights Reserved"
"All Rights Reserved" conflicts with the GPL.

Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
2009-07-29 09:59:22 +02:00
Alessandro Rubini
bb4291e625 arm nomadik: add i2c
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-07-29 09:57:47 +02:00
Alessandro Rubini
60cbfbfd0f arm nomadik: add gpio support
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-07-29 09:57:46 +02:00
Tom Rix
549b98306d OMAP3 Remove twl4030 defines
These defines have been subplanted by the equivelent defines in
include/twl4030.h

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
2009-07-29 09:57:45 +02:00
Tom Rix
fccc0fcaaa OMAP3 Move twl4030 mmc function
Because twl4030 now has its own device files, move and rename
twl4030_mmc_config.

twl4030_mmc_config initializes the twl4030 power setting to
the mmc device.  Because it is in the twl4030 power domain, move
it out of drivers/mmc/omap3_mmc.c and into drivers/power/twl4030.c.

The function was renamed to twl4030_power_mmc_init because all
the functions in this file are to have the format

twl4030_power_<device>_<action>

In this case the suffix is mmc_init so
device : mmc
action : init

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
2009-07-29 09:57:43 +02:00
Tom Rix
2c15513010 OMAP3 Move twl4030 power and led functions
Because twl4030 now has its own device files, move exiting
omap3 power_init_r to a new location.

power_init_r is the only function in board/omap3/common.
It initializes the twl4030 power for the board and enables
the led.

The power part of the the function is moved to twl4030_power_init in
drivers/power/twl4030.c The power compilation is conditional on the
existing config variable CONFIG_TWL4030_POWER.

The led part is moved to twl4030_led_init in the new file
drivers/misc/twl4030_led.c  The led compilation is conditional on
the new config variable CONFIG_TWL4030_LED

The directory board/omap3/common was removed because power_init_r
was the only function in it.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
2009-07-29 09:57:30 +02:00
Wolfgang Denk
d7b0781e2b Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx 2009-07-29 09:25:52 +02:00
Wolfgang Denk
03a14104f1 Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx 2009-07-29 09:15:36 +02:00
Wolfgang Denk
3cb7a4805f TQM8xx* boards: set larger SMC Rx buffer len
Commit 2b3f12c2 added support for configurable SMC Rx buffer length on
8xx systems. Enable this feature on TQM8xx* based boards.

This fixes the problem that pasting text in the middle of a line
(i. e. inserting in edit mode) did not work - only the first two
characters got inserted, the rest was lost.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-07-28 22:39:04 +02:00
Tom Rix
cd7826359e TWL4030 Add power reset button
The Zoom2 power reset button is on the top right side of the
main board.  Press and hold for about to 8 seconds to completely
reset the board.

Some of the beta boards have a hardware problem that prevents
using this feature.  If is difficult to further characterize the
boards that fail.  So disable resetting for all beta boards.

The Zoom1 reset button is the red circle on the top right,
front of the board.  Press and hold the button for 8 seconds to
completely reset the board.

After analyzing beagle, it was determined that other boards
that use the twl4030 for power managment can also make use
this function.

The resetting is done by the power management part of the twl4030.
Since there is no existing drivers/power, add one.

The compilation of power/twl4030.h is controlled by the config
variable CONFIG_TWL4030_POWER

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
2009-07-28 08:56:31 +02:00
Tom Rix
8966eb4c1c TWL4030 Add initial support
The TWL4030 supplies many peripherals for OMAP3 boards. These include
power management, usb and, keyboard.

The product description is found here:

http://focus.ti.com/docs/prod/folders/print/tps65950.html

Product reference document, tps65950.pdf, is found here:

http://www.ti.com/lit/gpn/tps65950

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
2009-07-28 08:55:39 +02:00
Tom Rix
7f79dfb48b OMAP I2C Fix the sampling clock.
This problem is seen on Zoom1 and Zoom2 in the startup and
when i2c probe is used

Before :

In:    serial
Out:   serial
Err:   serial
timed out in wait_for_bb: I2C_STAT=1000
timed out in wait_for_bb: I2C_STAT=1000
timed out in wait_for_bb: I2C_STAT=1000
timed out in wait_for_pin: I2C_STAT=1000
I2C read: I/O error
timed out in wait_for_bb: I2C_STAT=1000
timed out in wait_for_bb: I2C_STAT=1000
Die ID #327c00020000000004013ddd05026013
Hit any key to stop autoboot:  0
OMAP3 Zoom1# i2c probe
Valid chip addresses:timed out in wait_for_bb: I2C_STAT=1000
 02 03 04 05 06 07 08 09 0A 0B 0C 0D <snip>

After :

In:    serial
Out:   serial
Err:   serial
Die ID #327c00020000000004013ddd05026013
Hit any key to stop autoboot:  0
OMAP3 Zoom1# i2c probe
Valid chip addresses: 48 49 4A 4B

The addresses are for the twl4030.

The prescalar that converts the function clock to the sampling
clock is hardcoded to 0.  The reference manual recommends 7
if the function clock is 96MHz.

Instead of just changing the hardcoded values, the prescalar
is calculated from the value I2C_IP_CLK.

The i2c #defines are in kHz.  The speed passed into the
i2c init routine is in Hz.  To be consistent, change the
defines to be in Hz.

The timing calculations are based on what is done in the
linux 2.6.30 kernel in drivers/i2c/buses/i2c_omap.c as
apposed to what is done in TRM.

The major variables in the timing caculations are
specified as #defines that can be overriden as required.

The variables and their defaults are

I2C_IP_CLK				SYSTEM_CLOCK_96
I2C_INTERNAL_SAMPLING_CLK		19200000
I2C_FASTSPEED_SCLL_TRIM			6
I2C_FASTSPEED_SCLH_TRIM			6
I2C_HIGHSPEED_PHASE_ONE_SCLL_TRIM	I2C_FASTSPEED_SCLL_TRIM
I2C_HIGHSPEED_PHASE_ONE_SCLH_TRIM	I2C_FASTSPEED_SCLH_TRIM
I2C_HIGHSPEED_PHASE_TWO_SCLL_TRIM	I2C_FASTSPEED_SCLL_TRIM
I2C_HIGHSPEED_PHASE_TWO_SCLH		I2C_FASTSPEED_SCLH_TRIM

This was runtime verified on Zoom1, Zoom2, Beagle and Overo.
The 400kHz and 3.4M cases were verifed on test Zoom1,
Zoom2, Beagle and Overo configurations.

Testing for omap2 will be done in a second step as Nishanth
and Jean-Christophe commented.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
2009-07-28 08:52:33 +02:00
Stefan Roese
5b34691ff8 ppc4xx: Kilauea: Fix SDRAM init in NAND booting version
DDR2 Auto-calibration needs to be disabled on the NAND booting PPC4xx
targets. Otherwise the configured fixed init values for some DDR2
controller registers (e.g. RQDC) are not initialized at all resulting
in a non working SDRAM.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-28 07:23:54 +02:00
Dirk Eibach
ab4c62c1ba ppc4xx: Add GDsys CompactCenter board support.
Board support for the Guntermann & Drunck CompactCenter and
DevCon-Center.
Based on the AMCC Canyonlands board support by Stefan Roese.

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-28 07:20:34 +02:00
Reinhard Arlt
c2e49f706b mpc83xx: Add esd VME8349 board support
This patch adds support for the esd VME8349 board equipped with the
MPC8349. It's a VME PMC carrier board equipped with the Tundra
TSI148 VME-bridge.

Signed-off-by: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-07-27 18:36:36 -05:00
Paul Gortmaker
fe613cdd4e sbc8349: combine HRCW flash and u-boot image flash
Up to this point in time, the sbc8349 board was storing the u-boot
image in flash 2x.  One for the HRCW value at the beginning of
flash (0xff80_0000), and once close to the end of flash (0xfff8_0000)
for the actual image that got executed.

This moves the TEXT_BASE to be the beginning of flash, which makes
the second copy of the image redundant, and frees up the flash
from the end of the environment storage to the end of the flash
device itself.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-07-27 18:35:53 -05:00
Kim Phillips
be9b56df02 mpc83xx: CONFIG_83XX_GENERIC_PCI is now synonymous with CONFIG_PCI; remove the former
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-07-27 10:17:54 -05:00
Wolfgang Denk
c9ed38cb6d at91cap9adk: fix #ifdef/#endif pairing (2nd try)
Commit 7024aa14 was supposed to fix the #ifdef/#endif pairing in
include/configs/at91cap9adk.h, but did not cate all problems.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-07-27 10:01:11 +02:00
Wolfgang Denk
fb364bec5f Fix include/common.h for boards with CONFIG_STATUS_LED
The reordering of include/common.h by commit fcd3c87e49 broke
boards with status LED support, resulting in
	error: #error Status LED configuration missing
errors. Undo this reordering to avoid this issue.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-07-27 09:58:14 +02:00
Wolfgang Denk
fcd3c87e49 Make include/common.h usable by assembler code
Commit 70ebf316 factored out the ROUND() macro into include/common.h,
not realizing that the primary use of this macro on AT91 systems was
in start.S where common.h was not included, and could not be included
because it contains a lot of C code which the assembler doesn't
understand.

This patch wraps such code in common.h in a "#ifndef __ASSEMBLY__"
construct, and then adds an include to cpu/arm926ejs/start.S thus
solving the problem.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-07-27 00:12:32 +02:00
Wolfgang Denk
8bf7437c01 Merge branch 'master' of git://git.denx.de/u-boot-video 2009-07-26 23:15:57 +02:00
Wolfgang Denk
4e37963af7 Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx 2009-07-26 22:54:23 +02:00
Jens Scharsig
35cf3b57ea update the EB+MCF-EV123 board support
This patch updates the support for EB+MCF-EV123 board and needs
the [PATCH 1/2 V3] new video driver for bus vcxk framebuffers

* remove the board framebuffer driver
* use the common bus_vcxk framebuffer driver
* adds bmp support
* adds splashimage support
* fix serveral cosmetical errors

Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
[agust@denx.de: fixed some style issues before applying]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2009-07-26 13:19:23 +02:00
Jens Scharsig
50217deeb0 new video driver for bus vcxk framebuffers
This patch adds a new video driver

* adds common bus_vcxk framebuffer driver

Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
[agust@denx.de: fixed lots of style issues before applying]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2009-07-26 13:17:21 +02:00
Alessandro Rubini
60e9741924 lcd.h: define extern vidinfo_t for all cases
include/lcd.h has different vidinfo for different platforms,
and several extern declaration, but one for the default case was
missing. This makes them a single extern declaration for everyone.

Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
2009-07-26 13:16:50 +02:00
Mark Jackson
f68378d60a Add LCD support to MIMC200 board
This patch updates the MIMC200 files to enable the LCD.

Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
2009-07-26 13:14:33 +02:00
Mark Jackson
69f32e6c24 Add 16bit colour support in lcd.h
This patch adds support for LCD_COLOR16 in include/lcd.h.

Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
2009-07-26 13:14:14 +02:00