Those two boards are supposed to be run with a single u-boot binary.
There are notable differences though - HSC uses DSA switch (which
phy_id == 0x0) and DCC (DP83848C).
After the commit 3bf135b6c3
("drivers: net: phy: Ignore PHY ID 0 during PHY probing") the PHY devices
with phy_id == 0 are not created in U-Boot anymore. This caused regression
on HSC.
To fix this problem - the fec's 'fixed-link' node has been introduced and
the phy_id is not assessed anymore. This approach works on both boards.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
During the conversion of this board to DM_REGULATOR, usb-mass-storage
was broken and started failing with the following error:
=> ums 0 mmc 2
UMS: LUN 0, dev 2, hwpart 0, sector 0x0, count 0xe90000
Error enabling VBUS supply
g_dnl_register: failed!, error: -38
g_dnl_register failed
Fix this by adding the relevant GPIO to the regulator node.
Fixes: 4ca99fe81a ("ARM: imx: dh-imx6: Enable DM regulator")
Signed-off-by: Harald Seiler <hws@denx.de>
Use DM_ETH instead of legacy networking. Add VIO as a fixed regulator
to the relevant device-trees and augment the FEC node with properties
for the reset GPIO.
It should be noted that the relevant properties for the reset GPIO
already exist in the PHY node (reset-gpios, reset-delay-us,
reset-post-delay-us) but U-Boot currently ignores those and only
supports the bus-level reset properties in the FEC node
(phy-reset-gpios, phy-reset-duration, phy-reset-post-delay).
Signed-off-by: Harald Seiler <hws@denx.de>
The detection of the revD1 version is based on the presence of the PMIC.
Currently revb1 device trees are used for mx6q/mx6dl variants, which
do not have the PMIC nodes.
This causes revD1 boards to be incorrectly be detected as revB1.
Fix this issue by using the revd1 device trees, so that the PMIC node can be
found and then the PMIC can be detected by reading its register ID.
Imported the revd1 device trees from mainline kernel version 5.7-rc1.
Reported-by: Heiko Schocher <hs@denx.de>
Reported-by: Derek Atkins <derek@ihtfp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Derek Atkins <derek@ihtfp.com>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Linux doesn't provide skeleton.dtsi file so let's remove its include and
provide #address-cells/size-cells = <1> that were defined in
skeleton.dtsi before.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Add support for i.MXRT by adding CONFIG_IMXRT in register structure and
adding .compatible = "fsl,imxrt-lcdif".
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
The device trees for TQMa6x SOM support variations in
- CPU type: imx6dl- or imx6q-
- MBa6 I2C bus access: -mba6a (i2c1) or -mba6b (i2c3)
(plus the respective common/module include trees)
- USBH1 is directly connected to a hub
- USBOTG is connected to a separate connector
and can act as host/device or full OTG port.
Signed-off-by: Michael Krummsdorf <michael.krummsdorf@ew.tq-group.com>
The i.MX6DP and i.MX6QP incorporate NoC interconnect logic
which needs to be configured in order to use external DDR memory.
This patch enables the SPL to configure the necessary registers
in accordance with the NXP engineering bulletin EB828.
Co-developed-by: Filip Brozović <fbrozovic@gmail.com>
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
LDO mode may be already enabled by the ROM and enabling it again
can cause U-Boot to hang.
Avoid this problem by only enabling LDO mode if it is initially disabled.
Reported-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
These PMC0 definitions are already defined in the beginning
of the file, so remove the duplication.
Reported-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The LED labels do not match the silkscreen on the board, fix it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Activate ARCH_SUPPORT_TFABOOT and replace the arch stm32mp
specific config CONFIG_STM32MP1_TRUSTED by the generic CONFIG_TFABOOT
introduced by the commit 535d76a121 ("armv8: layerscape: Add TFABOOT
support").
This config CONFIG_TFABOOT is activated for the trusted boot chain,
when U-Boot is loaded by TF-A.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add DT entries, Kconfig entries and board-specific entries to configure
FMC2 bus and make KS8851-16MLL on that bus accessible to U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Define FMC2 base address, for use in board files, until there is an
actual FMC2 bus driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
- Misc enhancements to Clearfog, including board variant detection
(Joel)
- Misc enhancements to Turris Mox, including generalization of the
ARMADA37xx DDR size detection (Marek)
In case when ARM Trusted Firmware changes the default address of PCIe
regions (which can be done for devices with 4 GB RAM to maximize the
amount of RAM the device can use) we add code that looks at how ATF
changed the PCIe windows in the CPU Address Decoder and changes given
device-tree blob accordingly.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently on Armada-37xx the mem_map structure is statically defined to
map first 2 GB of memory as RAM region, and system registers and PCIe
region device region.
This is insufficient for when there is more RAM or when for example the
PCIe windows is mapped to another address by the CPU Address Decoder.
In the case when the board has 4 GB RAM, on some boards the ARM Trusted
Firmware can move the PCIe window to another address, in order to
maximize possible usable RAM.
Also the dram_init and dram_init_banksize looks for information in
device-tree, and therefore different device trees are needed for boards
with different RAM sizes.
Therefore we add code that looks at how the ARM Trusted Firmware has
configured the CPU Address Decoder windows, and then we update the
mem_map structure and compute gd->ram_size and gd->bd->bi_dram bank
base addresses and sizes accordingly.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Move Armada-8k specific DRAM init code into armada-8k specific
directory.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Commit e8e9715df2 requires the USB3 regulator node to have the
enable-active-high property for the regulator to work properly. The
GPIO_ACTIVE_HIGH constant is not enough anymore.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Fixes: e8e9715df2 ("regulator: fixed: Modify enable-active-high...")
Reviewed-by: Stefan Roese <sr@denx.de>
With recent changes to the mmc subsystem (chip detect code etc) update
the sdhci node of the Turris Mox device tree.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add a unique entry for ClearFog Base variant, reflected in the board
name and adjusted SerDes topology.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Using a consistent hardcoded MAC address from the DTS file causes
issues when using multiple devices on the same network segment.
Instead rely on environment configuration or random generation.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Update the RTC (Read Timing Control) values for PCIe memory wrappers
following an ERRATA (ERRATA# TDB). This means the PCIe accesses will
used slower memory Read Timing, to allow more efficient energy
consumption, in order to lower the minimum VDD of the memory. Will lead
to more robust memory when voltage drop occurs (VDDSEG)
The code is based on changes from Marvell's U-Boot, specifically:
20cd270407eb608a7c8dc4af19ae2b
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Sort the Armada series dts in the Makefile alphabetically
prior to adding new board support.
Signed-off-by: Josip Kelečić <josip.kelecic@sartura.hr>
Reviewed-by: Luka Kovacic <luka.kovacic@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Pull in changes that have been pending in our 'next' branch. This
includes:
- A large number of CI improvements including moving to gcc-9.2 for all
platforms.
- amlogic, xilinx, stm32, TI SoC updates
- USB and i2c subsystem updtaes
- Re-sync Kbuild/etc logic with v4.19 of the Linux kernel.
- RSA key handling improvements
Adding "u-boot,dm-pre-reloc" and enable CONFIG_SPL_CACHE
to enable cache driver in SPL.
This fixed error below in SPL:
cache controller driver NOT found!
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Update these 3 files from Linux:.
- socfpga_arria10.dtsi (Commit ID c1459a9d7e92)
- socfpga_arria10_socdk.dtsi (Commit ID d9b9f805ee2b)
- socfpga_arria10_socdk_sdmmc.dts (Commit ID 17808d445b6f)
Change in socfpga_arria10.dtsi:
- Add clkmgr label, so that can reference to it in u-boot.dtsi.
Change in socfpga_arria10-u-boot.dtsi:
- Add compatible and altr,sysmgr-syscon for uboot.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Move Uboot specific properties to *u-boot.dtsi files.
Preparation to sync Arria 10 device tree from Linux.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add and enable RTC-backed boot counter on ABB SECU1 platform.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
The FIT config node has reversed ATF and u-boot: ATF is set to 'firmware' but
u-boot is set to 'loadables'.
This script can work previously because spl fit driver wrongly appends fdt to
all loadable images. With the issue fixed in commit 9d15d1d1c2 ("Revert
"common: spl_fit: Default to IH_OS_U_BOOT if FIT_IMAGE_TINY enabled"") the
u-boot in 'loadables' does not have fdt appended and fails to work. So correct
the script by moving u-boot to 'firmware' and ATF to 'loadables'.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reported-by: Matt Porter <mporter@konsulko.com>
Tested-by: Matt Porter <mporter@konsulko.com>
- sync all Amlogic DT from Linux v5.6-rc2
- MMC clock fixups
- add support for Libre Computer AML-S905D-PC and AML-S912-PC
-----BEGIN PGP SIGNATURE-----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=PiOt
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200406' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic into next
- clk: meson-g12a: missing break
- sync all Amlogic DT from Linux v5.6-rc2
- MMC clock fixups
- add support for Libre Computer AML-S905D-PC and AML-S912-PC
pd_dma_* nodes should be accessible during pre-relocation stage of
U-Boot proper for properly handling power domains.
This fixes the issue with permanent failing of invocation of
power_domain_get_by_index() in the common code of DM power domain
uclass (drivers/power/domain/power-domain-uclass.c).
Fixes: f0cc4eae9a ("core: device: use dev_power_domain_on")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
pd_dma_* nodes should be accessible during pre-relocation stage of
U-Boot proper for properly handling power domains.
This fixes the issue with permanent failing of invocation of
power_domain_get_by_index() in the common code of DM power domain
uclass (drivers/power/domain/power-domain-uclass.c).
Fixes: f0cc4eae9a ("core: device: use dev_power_domain_on")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
For non-SPL/TPL setups dm-spl, dm-tpl, dm-pre-proper, dm-pre-reloc are
handled equally, forcing the nodes with these properties
to be accessible and device being probed
before pre-relocation of U-Boot proper (drivers/core/util.c):
bool ofnode_pre_reloc(ofnode node)
{
/* for SPL and TPL the remaining nodes after the fdtgrep 1st pass
* had property dm-pre-reloc or u-boot,dm-spl/tpl.
* They are removed in final dtb (fdtgrep 2nd pass)
*/
return true;
if (ofnode_read_bool(node, "u-boot,dm-pre-reloc"))
return true;
if (ofnode_read_bool(node, "u-boot,dm-pre-proper"))
return true;
/*
* In regular builds individual spl and tpl handling both
* count as handled pre-relocation for later second init.
*/
if (ofnode_read_bool(node, "u-boot,dm-spl") ||
ofnode_read_bool(node, "u-boot,dm-tpl"))
return true;
return false;
}
Howewer, to avoid confusion in future, replace dm-spl
`%s/dm-spl/dm-pre-proper/g` properties to dm-pre-proper
to explicitly state that they are handled during pre-relocation
stage of U-Boot proper.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
For non-SPL/TPL setups dm-spl, dm-tpl, dm-pre-proper, dm-pre-reloc are
handled equally, forcing the nodes with these properties
to be accessible and device being probed
before pre-relocation of U-Boot proper (drivers/core/util.c):
bool ofnode_pre_reloc(ofnode node)
{
/* for SPL and TPL the remaining nodes after the fdtgrep 1st pass
* had property dm-pre-reloc or u-boot,dm-spl/tpl.
* They are removed in final dtb (fdtgrep 2nd pass)
*/
return true;
if (ofnode_read_bool(node, "u-boot,dm-pre-reloc"))
return true;
if (ofnode_read_bool(node, "u-boot,dm-pre-proper"))
return true;
/*
* In regular builds individual spl and tpl handling both
* count as handled pre-relocation for later second init.
*/
if (ofnode_read_bool(node, "u-boot,dm-spl") ||
ofnode_read_bool(node, "u-boot,dm-tpl"))
return true;
return false;
}
Howewer, to avoid confusion in future, replace dm-spl
`%s/dm-spl/dm-pre-proper/g` properties to dm-pre-proper
to explicitly state that they are handled during pre-relocation
stage of U-Boot proper.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Similar change was done in past by commit 3b644a3c2f
("arm64: zynqmp: Provide a config to not map DDR region in MMU table").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
If ATF doesn't exist generate u-boot.itb without it and let U-Boot run in
EL3. Still keep warning to let user know that ATF/BL31 is missing.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Delay required for clock propagation is tighly coupled with initialization
done in psu_init(). That's why call it also for u-boot proper with
CONFIG_ZYNQMP_PSU_INIT_ENABLED enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
board_early_init_f() is the right location where debug uart can be
configurated (after MIO initialization).
The patch is taking this call from SPL to also make it available for U-Boot
proper.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
I found this issue when was running py/test.py on zcu102 which is for me by
default setup to SD boot mode without any way to change boot mode.
Alternative software bootmode selection to JTAG is not working because JTAG
mode is 0 which also reset value for it. That's why saying SPL to take
u-boot.itb from RAM instead of SD in SD boot mode is not possible via
alternative bootmode selection.
That's why setup third boot mode to JTAG(BOOT_DEVICE_RAM) as final
fallback.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This information is shown already that's why there is no reason to print it
again via custom prints.
U-Boot SPL 2020.01-03080-ga6214d033bd0 (Mar 05 2020 - 09:59:05 +0100)
mmc boot
Trying to boot from MMC1
or
U-Boot SPL 2020.01-03080-ga6214d033bd0 (Mar 05 2020 - 10:49:46 +0100)
qspi boot
Trying to boot from SPI
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
With multi defconfig NOR flash information about NOR should be taken from
DT that's why there is no reason to specify address and sizes via fixed
config.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no real need to include full DT when only some nodes are enough to
use. It will save some space.
Retested with FSBL for initial SoC setup. SPL didn't work.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
