The enable_fec_anatop_clock method should be available for all MX6
variant as it is not MX6 SoloLite specific. This moves the code out of
the #ifdef/#endif and we make it conditional to CONFIG_FEC_MXC
instead.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
As U-boot does not use GPU/VPU peripherals, shutdown the VDDPU regulator
in order to save power.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When changing LDO voltages we need to wait for the required amount of time
for the voltage to settle.
Also, as the timer is still not available when arch_cpu_init() is called, we
need to call it later at board_postclk_init() phase.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Since ROM may modify the LDO ramp up time according to fuse setting,
it is safer to reset the ramp up field to its default value of 00:
00: 64 cycles of 24MHz clock;
01: 128 cycles of 24MHz clock;
02: 256 cycles of 24MHz clock;
03: 512 cycles of 24MHz clock;
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
ROM did not invalidate L1 cache when download by usb
Need invalidate L1 cache before enable cache
Signed-off-by: Huang yongcai <b20788@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
According to the mx6 quad reference manual, the DIV_SELECT field of register
CCM_ANALOG_PLL_ENETn has the following meaning:
"Controls the frequency of the ethernet reference clock.
- 00 - 25MHz
- 01 - 50MHz
- 10 - 100MHz
- 11 - 125MHz"
Current logic does not handle the 25MHz case correctly, so fix it.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Conflicts:
arch/arm/cpu/arm926ejs/mxs/Makefile
board/compulab/cm_t35/Makefile
board/corscience/tricorder/Makefile
board/ppcag/bg0900/Makefile
drivers/bootcount/Makefile
include/configs/omap4_common.h
include/configs/pdnb3.h
Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:
board/compulab/common/Makefile
board/udoo/Makefile
include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.
include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.
Note: 'git show' will also list two files just because
they are new:
include/configs/am335x_igep0033.h
include/configs/omap3_igep00x0.h
The value MXC_CCM_CCGR3_IPU1_IPU_DI0_OFFSET that was used to initialize
the CCGR3 register caused an undefined value for CG0.
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
CC: Stefano Babic <sbabic@denx.de>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
This is porting of Freescale's patch from version imx_v2009.08_3.0.35_4.0.0,
that fixes the obvious mistype of bits offset macro name (ACLK_EMI_PODF_OFFSET
was used instead of ACLK_EMI_SLOW_PODF_OFFSET).
Using the occasion, change the variable name 'emi_slow_pof' to more consistent
'emi_slow_podf'.
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Add functions to report the HAB (High Assurance Boot) status
of e.g. i.MX6 CPUs.
This is taken from
git://git.freescale.com/imx/uboot-imx.git branch imx_v2009.08_3.0.35_4.0.0
cpu/arm_cortexa8/mx6/generic.c
include/asm-arm/arch-mx6/mx6_secure.h
Signed-off-by: Stefano Babic <sbabic@denx.de>
Instead of duplicating HDMI setup code for every mx6 board, factor out the common code
Signed-off-by: Pardeep Kumar Singla <b45784@freescale.com>
Acked-By: Eric Nelson <eric.nelson@boundarydevices.com>
IIM:
- Homogenize prg_p naming (the reference manuals are not always self-consistent
for that).
- Add missing SCSx and bank registers.
- Fix the number of banks on i.MX53.
OCOTP:
- Rename iim to ocotp in order to avoid confusion.
- Rename fuse_data to read_fuse_data, and sticky to sw_sticky, according to the
reference manual.
- Merge the existing spinoff gp1 fuse definition on i.MX6.
- Fix the number of banks on i.MX6.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: Stefano Babic <sbabic@denx.de>
When booting a Freescale kernel 3.0.35 on a Wandboard solo, the get_board_rev()
returns 0x62xxx, which is not a value understood by the VPU
(Video Processing Unit) library in the kernel and causes the video playback to
fail.
The expected values for get_board_rev are:
0x63xxx: For mx6quad/dual
0x61xxx: For mx6dual-lite/solo
So adjust get_board_rev() accordingly and make it as weak function, so that we
do not need to define it in every mx6 board file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
Now that U-Boot has common CONFIG_ options to work around some ARM CPU
errata, enable the relevant options on MX6, and remove the custom
lowlevel_init.S, since it's just duplicated code now.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
On a mx6qsabresd revision C board with rev1.2 mx6q, the system gets resetted
and it is not able to reach the Linux prompt.
Comparing the watchdog behaviour on a revB versus revC board:
- On a mx6qsabresd revB:
U-Boot > reset
resetting ...
U-Boot 2013.01-10524-g432a3aa-dirty (Feb 07 2013 - 13:34:46)
CPU: Freescale i.MX6Q rev1.1 at 792 MHz
Reset cause: WDOG
...
- On a mx6qsabresd revC:
U-Boot > reset
resetting ...
U-Boot 2013.01-10524-g432a3aa-dirty (Feb 07 2013 - 13:34:46)
CPU: Freescale i.MX6Q rev1.1 at 792 MHz
Reset cause: POR
So due to revC POR/watchdog circuitry whenever a watchdog occurs, it causes a POR.
Clearing the PDE - Power Down Enable bit of WMCR registers fixes the problem and
is also safe for all mx6 boards.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
Add workaround for the following ARM errata: 743622 and 751472.
The motivation for this change is the following kernel commit 62e4d357a
(ARM: 7609/1: disable errata work-arounds which access
secure registers), which removes the errata from multiplatform kernel.
Since imx has been converted to multiplatform in the kernel, we need to apply
such workarounds into the bootloader.
Workaround code has been taken from arch/arm/mm/proc-v7.S from 3.7.1 kernel.
Explanation of each erratum is provided at "Chip Errata for the i.MX 6Dual/6Quad"
document available at: cache.freescale.com/files/32bit/doc/errata/IMX6DQCE.pdf
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
If a board does not enable CSPI, there is no need to show the CSPI clock
frequency as part of the 'clock' command.
Reported-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Dirk Behme <dirk.behme@gmail.com>
Previously, the same value was returned for both mx6dl and mx6solo.
Check number of processors to differeniate.
Also, a freescale patch says that sololite has its cpu/rev
stored at 0x280 instead of 0x260.
I don't have a sololite to verify.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Define default SoC input clock frequencies for i.MX5/6 in order to get rid of
duplicated definitions.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jason Liu <r64343@freescale.com>
Cc: Matt Sealey <matt@genesi-usa.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
i2c didn't work on imx25 due to missing MXC_IPG_PERCLK. Now using
MXC_I2C_CLK on all imx systems using i2c.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Add meaningful constants for each clock channels and use them for
enabling and disabling i.MX6 clocks.
Includes an update to enable/disable the IPU1 clock in
drivers/video/ipu_common to remove IMX5x register access
when used on i.MX6 as discussed in V1:
http://patchwork.ozlabs.org/patch/185129/
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
This is useful for forcing the ROM's
usb downloader to activate upon a watchdog reset.
Or, you can boot from either SD Card.
Currently, support added for MX53 and MX6Q
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Note: MX53 support untested.
Acked-by: Stefano Babic <sbabic@denx.de>
Init the core regulator voltage to 1.2V. This is required for the correct
functioning of the GPU and when the ARM LDO is set to 1.225V. This is a
workaround to fix some memory clock jitter.
Note: This should be but can't be done in the DCD. The bootloader
prevents access to the ANATOP registers.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Jason Chen <b02280@freescale.com>
CC: Jason Liu <r64343@freescale.com>
CC: Ranjani Vaidyanathan <ra5478@freescale.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <festevam@gmail.com>
get_ahb_clk() is a common function between mx5 and mx6.
Place it into imx-common directory.
Cc: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Use ENTRY and ENDPROC with assembly functions to ensure
necessary assembler directives for all functions.
Signed-off-by: Aneesh V <aneesh@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Instead of hardcoding the mx6 silicon revision, read it in run-time.
Also, besides the silicon version print the mx6 variant type: quad,dual/solo
or solo-lite.
Tested on a mx6qsabrelite, where it shows:
CPU: Freescale i.MX6Q rev1.0 at 792 MHz
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <r64343@freescale.com>
For the i.mx6q, the burned-in MAC address will be the following odering,
fuse: 0x620[7:0] MAC_ADDR[7:0] ---> mac[5]
fuse: 0x620[15:8] MAC_ADDR[15:8] ---> mac[4]
fuse: 0x620[23:16] MAC_ADDR[23:16] ---> mac[3]
fuse: 0x620[31:24] MAC_ADDR[31:24] ---> mac[2]
fuse: 0x630[7:0] MAC_ADDR[39:32] ---> mac[1]
fuse: 0x630[15:8] MAC_ADDR[47:40] ---> mac[0]
This patch also fix the error caculation for the fuse bank[0] address
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Add multi-FEC support for imx_get_mac_from_fuse by passing dev_id as a parameter.
This feature is important on mx28 SoC for example that has two FEC ports.
Cc: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
i.MX6Q is freescale quad core processors with ARM cortex_a9 complex.
This patch is to add the initial support for this processor.
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc:Stefano Babic <sbabic@denx.de>
