Commit graph

166 commits

Author SHA1 Message Date
Jagan Teki
4e9de9eba8 ram: rk3399: Map chipselect for lpddr4
Assign desired cs_map values for lpddr4 during set memory map.

Initial cs_map values is based on the sdram parameters, so
the same will adjusted based dramtype as LPDDR4.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
2019-07-20 23:59:44 +08:00
Jagan Teki
d3d0099ca6 ram: rk3399: Configure PHY RX_CM_INPUT for lpddr4
Configure PHY RX_CM_INPUT for lpddr4 during phy IO config.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20 23:59:44 +08:00
Jagan Teki
f9f32d61a6 ram: rk3399: Configure SLEWP_EN, SLEWN_EN for lpddr4
Configure SLEWP_EN, SLEWN_EN for lpddr4 during phy IO config.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
2019-07-20 23:59:44 +08:00
Jagan Teki
881860fd34 ram: rk3399: Configure BOOSTP_EN, BOOSTN_EN for lpddr4
Configure BOOSTP_EN, BOOSTN_EN for lpddr4 during phy IO config.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20 23:59:44 +08:00
Jagan Teki
009fe1bac9 ram: rk3399: Configure PHY_898, PHY_919 for lpddr4
PHY_898, PHY_919 would require to configure PHY LP4 boot
pll control and ca for lpddr4.

So, configure the same in pctl_cfg for LPDDR4.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20 23:59:44 +08:00
Jagan Teki
47627c8a5c ram: rk3399: Avoid two channel ZQ Cal Start at the same time
It is possible in lpddr4 dram, where both the channels would
start at same time with ZQ Cal Start. If it uses ZQ Call start
then it will use RZQ.

For example LPDDR4 366 Dual-Die, Quad-Channel Package, RZQ maybe
connect to both channel. If ZQ Cal Start at the same time,
it will use the same RZQ.

It is not a problem of using RZQ in both the channels, but can not
use at the same time.

So, to avoid this, we have an option of dram tINIT3 value for
increasing the frequency for channel 1.

This patch increase the available tINIT3 with existing running
dram frequency.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20 23:59:44 +08:00
Jagan Teki
5cbc866981 ram: rk3399: Don't wait for PLL lock in lpddr4
lpddr4 has PLL bypass mode during phy initialization phase,
which does all pll configurations.

So no need to wait explicitly during pctl config.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20 23:59:44 +08:00
Jagan Teki
6cbd2426b3 ram: rk3399: Move mode_sel assignment
mode_sel assignment is based on dram type.

In phy_io_config, already have vref setting based
on the dram type, so move this mode_sel assignment
on vref setting area.

No functionality change.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20 23:59:44 +08:00
Jagan Teki
c716bf67f5 ram: rk3399: Add lpddr4 rank mask for wdql training
Add rank_mask based on the rank number for lpddr4.

This would keep the wdql data training loop based on the
desired rank mask value instead of looping for all values.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20 23:59:44 +08:00
Jagan Teki
3dae87da89 ram: rk3399: Add lpddr4 rank mask for ca training
Add rank_mask based on the rank number for lpddr4.

This would keep the ca data training loop based on the
desired rank mask value instead of looping for all values.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20 23:59:44 +08:00
Jagan Teki
b6cf08949d ram: rockchip: Kconfig: Add RK3399 LPDDR4 entry
Supporting LPDDR4 code support in RK3399 would increases
the size of SPL/TPL.

So add kconfig entry for RK3399 LPDDR4 code so-that
the boards have LPDDR4 can enable them via defconfig.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20 23:59:44 +08:00
Jagan Teki
ba607fafd1 ram: rk3399: Configure phy IO in ds odt
Some dramtypes like lpddr4 initialization would required to
configure phy IO even after pctl_cfg and after set_ds_odt.

For those cases the set_ds_odt would be an initial call to
setup the phy.

To satisfy all the cases, trigger phy IO from set_ds_odt.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20 23:59:44 +08:00
Jagan Teki
a735550bb8 ram: rk3399: Add DdrMode
Add DdrMode structure with associated bit fields.

These would help to reconfigure sdram capabilities during
lpddr4 setup related configs.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20 23:59:44 +08:00
Jagan Teki
ed77ce728a ram: rk3399: Add ddrtimingC0
Add DdrTimingC0 structure with associated bit fields.

These would help to reconfigure sdram capabilities during
lpddr4 setup related configs.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20 23:59:44 +08:00
Jagan Teki
b713e0291b ram: rk3399: Add ddr version enc macro
Add dram config macro for handling ddr version number.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20 23:59:44 +08:00
Jagan Teki
01cc103915 ram: rk3399: Introduce sys_reg3 for more capacity info
cs0_row, cs1_row and cs1_col needs more bits to show its
correct value, update to make use of both sys_reg2,
sys_reg3.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
(Squash similar patches into one patch)
Signed-off-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20 23:59:44 +08:00
Jagan Teki
e0ddb0ba21 ram: rk3399: Rename sys_reg with sys_reg2
Use dram config variable name as sys_reg2 instead of sys_reg
since the final variable value is to written into a pmugrf
register named as sys_reg2.

This reflect the both variable and associated register
names are same and also help to add next sys_reg's to
add it in future.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20 23:59:44 +08:00
Jagan Teki
879f9fed6a ram: rk3399: Simply existing dram enc macro
Add simplified and meaningful macro for all setting.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
(Squash the similar patches into 1 patch)
Signed-off-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20 23:59:44 +08:00
Jagan Teki
a9191b8eec ram: rk3399: Enable sdram debug functions
This would help to debug the sdram base parameters while
debugging existing chip or while supporting new sdram type.

It require explicit enablement of CONFIG_RAM_ROCKCHIP_DEBUG
for showing the debug prints.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20 23:59:44 +08:00
Jagan Teki
d0ba88f5dd ram: rk3399: Add rank detection support
Right now the rk3399 sdram driver assume that the board
has configured with 2 channels, so any possibility to
enable single channel on the same driver will encounter
channel #1 data training failure.

Log:
U-Boot TPL board init
sdram_init: data training failed
rk3399_dmc_init DRAM init failed -5

So, add an algorithm that can capable to compute the active
or configured rank with associated channel like
a) do rank loop to compute the active rank, with associated
   channel numbers
b) then, succeed the data training only for configured channel
c) preserve the rank for given channel
d) do channel loop for setting the active channel
e) if given rank is zero or inactive on the specific channel,
   clear the timings for the associated channel
f) finally, return error if number of channels is zero

Tested in NanoPI-NEO4 since it support single channel sdram
configuration.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
(add PI_READ_GATE_TRAINING for LPDDR3 to support rk3399-evb case)
Signed-off-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20 23:54:32 +08:00
Jagan Teki
1ff5283d92 ram: rk3399: Compute stride for 1 channel a
Add stride computation for the sdram which support
single channel a

This configuration available in NanoPi NEO4 and the
same can work with existing rk3399-sdram-ddr3-1866.dtsi

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-19 11:11:10 +08:00
Jagan Teki
4b09719c38 ram: rk3399: Compute stride for 2 channels
stride value from sdram timings can be computed dynamically
based on the determined capacity for the given channel.

Right now these stride values are taken as part of sdram timings
via dtsi, but it possible to use same timings dtsi for given
frequency even though the configured board sdram do support
single channel with different size by dynamically detect the
stride value.

Example, NanoPi NEO4 do have DDR3-1866, but with single channel
and 1GB size with dynamic stride detection it is possible to
use existing rk3399-sdram-ddr3-1866.dtsi whose stride,
number of channels and capacity it support is d efferent.

So, add initial support to calculate the stride value for
2 channels sdram, which is available by default on existing
boards.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-19 11:11:10 +08:00
Jagan Teki
cb13534abe ram: rk3399: debug: Add sdram_print_stride
Add code to print the channel stride, this would help to
print the stride of associated channel.

Here is sample print on LPDDR4, 50MHz.
256B stride

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-19 11:11:10 +08:00
Jagan Teki
79674a6278 ram: rockchip: debug: Get the cs capacity
Add code to get the channel capacity, this would help to
print the capacity of specific channel.

Here is sample print on LPDDR4, 50MHz channel 0
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-19 11:11:10 +08:00
Jagan Teki
07894f5aac ram: rockchip: debug: Add sdram_print_ddr_info
Add sdram ddr info print support, this would help to
observe the sdram base parameters.

Here is sample print on LPDDR4, 50MHz channel 0
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-19 11:11:10 +08:00
Jagan Teki
07112672a5 ram: rockchip: Add debug sdram driver
Add sdram driver to handle debug across rockchip SoCs.

This would help to improve code debugging feature for
sdram drivers in rockchip family, whoever wants to
debug the driver should call these core debug code on
their respective platform sdram drivers.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-19 11:11:09 +08:00
Jagan Teki
82ee138def ram: rockchip: Add initial Kconfig
Right now sdram drivers in rockchip SoC are built based
on the SoC configs which may not be an adequate solutions
while adding common or debug driver.

So, add meaningful Kconfig options start with rk3399.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-19 11:11:09 +08:00
Jagan Teki
a0aebe8398 ram: rk3399: Add pctl start support
Add support for pctl start for both channel 0, 1 control
and phy registers.

This would also handle pwrup_srefresh_exit init based
on the channel number.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-19 11:11:09 +08:00
Jagan Teki
fe42d4a199 ram: rk3399: Move pwrup_srefresh_exit to dram_info
Add pwrup_srefresh_exit to be part of dram_info so-that
the it can help to support pwrup_srefresh_exit in individual
channels while starting pctl in future.

No functionality change.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-19 11:11:09 +08:00
Jagan Teki
33921035be ram: rk3399: Add phy pctrl reset support
Add support for phy pctrl reset support for both channel 0, 1.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-19 11:11:09 +08:00
Jagan Teki
21cf392b1f ram: rk3399: Use rank mask in wdql data training
Add rank_mask based on the rank number, this would keep
the wdql data training loop based on the desired rank mask
value instead of looping for all values.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-19 11:11:09 +08:00
Jagan Teki
708e9a79dc ram: rk3399: Use rank mask in ca data training
Add rank_mask based on the rank number, this would keep
the ca data training loop based on the desired rank mask
value instead of looping for all values.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-19 11:11:09 +08:00
Jagan Teki
01976ae6f5 ram: rk3399: Clear PI_175 interrupts in data training
Clear the PI_175 interrupts before processing actual
data training in all relevant calls.

This would help to clear interrupt from previous training.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-19 11:11:09 +08:00
Jagan Teki
02fad6f9ed ram: rk3399: Handle data training return types
data trainings calls like ca, wl, rg, rl, wdql have proper
return types with -EIO and the return type missed to handle
in data_training function.

This patch, add proper return type checks along with useful
debug statement on each data training calls.

Incidentally this would help to prevent the sdram initialization
hang for single channel dram and when the code is trying to
initialize second channel with proper return type of relevant
data training call might failed.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-19 11:11:09 +08:00
Jagan Teki
355490dc5c ram: rockchip: rk3399: Add cap_info structure
Group common ddr attributes like
- rank
- col
- bk
- bw
- dbw
- row_3_4
- cs0_row
- cs1_row
- ddrconfig

into a common cap_info structure for more code readability and extend
if possible based on the new features.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-19 11:11:09 +08:00
Jagan Teki
9c4d517db8 ram: rk3399: Order tsel variables
Order tsel* variable declarations and assignment in proper
and meaningful way.

No functionality change.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-19 11:11:09 +08:00
Jagan Teki
30bd86a399 ram: rk3399: s/ca_tsel_wr_select_p/tsel_wr_select_ca_p
Rename ca_tsel_wr_select_p to tsel_wr_select_ca_p based
on the bsp code.

No functionality change.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-19 11:11:09 +08:00
Jagan Teki
a12a5be7a3 ram: rk3399: s/ca_tsel_wr_select_n/tsel_wr_select_ca_n
Rename ca_tsel_wr_select_n to tsel_wr_select_ca_n based
on the bsp code.

No functionality change.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-19 11:11:09 +08:00
Jagan Teki
a5085ee4e8 ram: rk3399: s/tsel_wr_select_p/tsel_wr_select_dq_p
Rename tsel_wr_select_p to tsel_wr_select_dq_p based
on the bsp code.

No functionality change.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-19 11:11:09 +08:00
Jagan Teki
fa2b015b9c ram: rk3399: s/tsel_wr_select_n/tsel_wr_select_dq_n
Rename tsel_wr_select_n to tsel_wr_select_dq_n based
on the bsp code.

No functionality change.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-19 11:11:09 +08:00
Jagan Teki
d4b4bb47c6 ram: rk3399: Handle pctl_cfg return type
Add proper return type handling of pctl_cfg with
meaningful print statement.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-19 11:11:09 +08:00
Jagan Teki
fde7f457e1 ram: rk3399: s/sdram_params/params
Rename variable name of struct rk3399_sdram_params
from sdram_params with params for more code readability.

No functionality change.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-19 11:11:09 +08:00
Jagan Teki
3eaf539849 ram: rk3399: Some trivial code fixes
- Add proper spaces in data training, rk3399_dmc_init, pctl_cfg
- Order include files
- Move macro after include files

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-19 11:11:09 +08:00
Jagan Teki
63f4d716b1 ram: rk3399: Fix code warnings
Fix checkpatch warninigs on sdram_rk3399.c like
- Avoid CamelCase
- Unnecessary parentheses
- Alignment should match open parenthesis
- multiple blank lines
- misspelled
- spaces preferred around that '>>'

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-19 11:11:09 +08:00
Patrick Delaunay
588448517f ram: stm32mp1_ram: Fix warnings when compiling with W=1
This patch solves the following warnings:

drivers/ram/stm32mp1/stm32mp1_ram.c: In function 'stm32mp1_ddr_clk_enable':
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
  for (idx = 0; idx < ARRAY_SIZE(clkname); idx++) {
                    ^
drivers/ram/stm32mp1/stm32mp1_ram.c: In function 'stm32mp1_ddr_setup':
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
  for (idx = 0; idx < ARRAY_SIZE(param); idx++) {
                    ^
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12 11:50:56 +02:00
Patrick Delaunay
187c41d783 stm32mp1: ram: add tuning in DDR interactive mode
Add command tuning for DDR interactive mode, used during
board bring-up or with CubeMX DDR tools to execute software
tuning for the DDR configuration:
- software read DQS Gating (replace the built-in one)
- Bit de-skew
- Eye Training or DQS training

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-05-23 11:38:11 +02:00
Patrick Delaunay
0d44752442 stm32mp1: ram: add tests in DDR interactive mode
Add command tests for DDR interactive mode, used during
board bring-up or with CubeMX DDR tools to verify the
DDR configuration.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-05-23 11:38:11 +02:00
Patrick Delaunay
01a7510849 stm32mp1: ram: add interactive mode for DDR configuration
This debug mode is used by CubeMX DDR tuning tools
or manualy for tests during board bring-up.
It is simple console used to change DDR parameters and check
initialization.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-05-23 11:38:11 +02:00
Patrick Delaunay
1767ac2d1f stm32mp1: ram: add support for LPDDR2/LPDDR3
Manage power supply configuration for board using stpmic1
with LPDDR2 or with LPDDR3:
+ VDD_DDR1 = 1.8V with BUCK3 (bypass if possible)
+ VDD_DDR2 = 1.2V with BUCK2

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-05-23 11:38:11 +02:00
Patrick Delaunay
53bb831658 stm32mp1: ram: update parameter array initialization
Force alignment of the size of parameters array with
the expected value in the binding, that allows compilation
error when the array size change.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-05-23 11:38:10 +02:00
Patrick Delaunay
c60fed14f6 stm32mp1: ram: change ddr speed to kHz
Allow fractional support in DDR tools.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-05-23 11:38:10 +02:00
Patrick Delaunay
0cb1aa9409 stm32mp1: ram: increase the delay after reset to 128 cycles
Component Notification DDR controller errata (3.00a):9001313030
Synchronization Time Waited After De-assertion of presetn is
128 pclk Cycles.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-05-23 11:38:10 +02:00
Patrick Delaunay
c3ec370aed stm32mp1: ram: update mask for operating mode
Regression introduced by rebase, when loop
was replaced by readl_poll_timeout() function.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-05-23 11:38:10 +02:00
Mario Six
8439e99ddb mpc83xx: Introduce ARCH_MPC837X
Replace CONFIG_MPC837x with a proper CONFIG_ARCH_MPC837X Kconfig option.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
2019-05-20 13:50:34 +02:00
Mario Six
61abced70f mpc83xx: Introduce ARCH_MPC836*
Replace CONFIG_MPC836* with proper CONFIG_ARCH_MPC836* Kconfig options.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
2019-05-20 13:50:34 +02:00
Mario Six
9403fc41c7 mpc83xx: Introduce ARCH_MPC831*
Replace CONFIG_MPC833* with proper CONFIG_ARCH_MPC833* Kconfig options.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
2019-05-20 13:50:34 +02:00
Mario Six
4bc97a3b81 mpc83xx: Introduce ARCH_MPC830*
Replace CONFIG_MPC830* with proper CONFIG_ARCH_MPC830* Kconfig options.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
2019-05-20 13:50:34 +02:00
Kever Yang
82763349a2 rockchip: ram: rk3399: update for TPL
Init the ddr sdram in TPL instead of SPL, update the code.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
2019-05-08 17:34:12 +08:00
Kever Yang
99a1a5b195 rockchip: dmc: rk3368: update rank number for evb-px5
evb-px5 has only 1 CS, update for it.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
2019-05-08 17:34:12 +08:00
Kever Yang
2f52378736 Revert "rockchip: rk322x: ram: enable DRAM init in SPL instead of TPL"
This reverts commit f338cca1d2.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-08 17:34:12 +08:00
Kever Yang
15f09a1a83 rockchip: use 'arch-rockchip' as header file path
Rockchip use 'arch-rockchip' instead of arch-$(SOC) as common
header file path, so that we can get the correct path directly.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-05-01 00:00:05 +02:00
Patrick Delaunay
abf2678f0f stm32mp1: add trusted boot with TF-A
Add support of trusted boot, using TF-A as first stage bootloader,
The boot sequence is
  BootRom >=> TF-A.stm32 (clock & DDR) >=> U-Boot.stm32

The TF-A monitor provides secure monitor with support of SMC
- proprietary to manage secure devices (BSEC for example)
- PSCI for power

The same device tree is used for STMicroelectronics boards with
basic boot and with trusted boot.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12 16:09:13 +02:00
Kever Yang
c43acfdc24 rockchip: ram: update license for sdram driver
Rockchip may use this sdram copy of source code for both open source
and internal project, update the license to use both GPL2.0+ and
BSD-3 Clause.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-01-02 22:37:10 +01:00
Kever Yang
f338cca1d2 rockchip: rk322x: ram: enable DRAM init in SPL instead of TPL
Patch for rk322x TPL is not merged, and only SPL is available now,
enable the sdram driver in SPL first. We should update back to TPL
after TPL is enabled for rk322x.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-12-10 10:04:44 +01:00
Ryder Lee
60f633efd5 ram: MediaTek: add DDR3 driver for MT7629 SoC
This patch adds a DDR3 driver for MT7629 SoC.

Signed-off-by: Wu Zou <wu.zou@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-11-28 23:04:53 -05:00
Lokesh Vutla
06bda1259f ram: Introduce K3 AM654 DDR Sub System driver
K3 based AM654 devices has DDR memory subsystem that comprises
Synopys DDR controller, Synopsis DDR phy and wrapper logic to
intergrate these blocks into the device. This DDR subsystem
provides an interface to external SDRAM devices. Adding support
for the initialization of the external SDRAM devices by
configuring the DDRSS registers and using the buitin PHY
routines.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: James Doublesin <doublesin@ti.com>
2018-11-16 16:51:58 -05:00
Bin Meng
05e424818b ram: bmips: Remove DM_FLAG_PRE_RELOC flag
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.

To mitigate this potential impact, the following changes are
implemented:

- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
  only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
  is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
  drivers that support both statically declared devices and
  configuration from device tree

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-11-14 09:16:28 -08:00
Patrick Delaunay
22929e1266 drivers: cosmetic: Convert SPDX license tags to Linux Kernel style
Complete in the drivers directory the work started with
commit 83d290c56f ("SPDX: Convert all of our single
license tags to Linux Kernel style").

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-10-28 09:26:39 -04:00
Mario Six
e40615565d ram: Add driver for MPC83xx
Add a RAM driver for the MPC83xx architecture.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-09-18 00:01:18 -06:00
Philippe Reynes
3e4a68d32b bmips: ram: add an option to force the size of the ram
This adds an option to force the size of the ram, and
avoid the detection of ram size.

Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-08-08 13:34:27 +02:00
Álvaro Fernández Rojas
13a7bfe490 ram: bmips: convert to use live dt
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-06-01 15:56:02 +02:00
Radoslaw Pietrzyk
246a5e5fc2 ram: stm32_sdram: Adds stm32f429-disco fixes for HardFault at booting
- adds reading FMC swap setting from DTB to SDRAM driver
- sets FMC swap for stm32f429-disco board
- changes ram start address to 0x90000000

Signed-off-by: Radoslaw Pietrzyk <radoslaw.pietrzyk@gmail.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
2018-05-26 18:19:17 -04:00
Masahiro Yamada
d35812368a regmap: change regmap_init_mem() to take ofnode instead udevice
Currently, regmap_init_mem() takes a udevice. This requires the node
has already been associated with a device. It prevents syscon/regmap
from behaving like those in Linux.

Change the first argumenet to take a device node.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-05-07 15:49:51 -04:00
Tom Rini
4549e789c1 SPDX: Convert all of our multiple license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have multiple licenses (in
these cases, dual license) declared in the SPDX-License-Identifier tag.
In this case we change from listing "LICENSE-A LICENSE-B" or "LICENSE-A
or LICENSE-B" or "(LICENSE-A OR LICENSE-B)" to "LICENSE-A OR LICENSE-B"
as per the Linux Kernel style document.  Note that parenthesis are
allowed so when they were used before we continue to use them.

Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 10:24:31 -04:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Tom Rini
d024236e5a Remove unnecessary instances of DECLARE_GLOBAL_DATA_PTR
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-27 14:54:48 -04:00
Heinrich Schuchardt
2ebc80e83c driver: ram: rockchip: rk3399: missing counter increment
If we want to check the duration we need to increment the counter.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-03-28 23:30:31 +02:00
Patrick Delaunay
e70f70aa65 ram: stm32mp1: add driver
Add driver and binding for stm32mp1 ddr controller and phy

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-03-19 16:14:21 -04:00
Álvaro Fernández Rojas
a80bf5e46e dm: ram: bmips: add BCM6318 support
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-01-26 12:38:13 +01:00
Patrice Chotard
0b3f789ad1 ram: stm32: add memory mapping selection support
This allows to controls the memory internal mapping at
address 0x0000 0000.
We can either map at 0x0000 0000 :
  _ main flash memory
  _ system flash memory
  _ FMC bank1 (NOR/PSRAM 1 and 2)
  _ embedded SRAM
  _ FMC/SDRAM bank1

This is needed for future STM32F469-disco board

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-01-10 08:05:47 -05:00
Kever Yang
b7aef28953 rockchip: rk3128: add sdram driver
RK3128 support up to 2GB DDR3 sdram, one channel, 32bit data width.

This patch is only used for U-Boot, but not for SPL which will
comes later, maybe after we merge all the common code into a common
file.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-30 22:55:27 +01:00
Patrice Chotard
3bc599c956 stm32: fix STMicroelectronics copyright
Uniformize STMicroelectronics copyrights headers for STM32
related code.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-11-06 09:51:01 -05:00
Masahiro Yamada
9b643e312d treewide: replace with error() with pr_err()
U-Boot widely uses error() as a bit noisier variant of printf().

This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:

  # define __compiletime_error(message) __attribute__((error(message)))

This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux.  (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)

Let's convert error() into now treewide-available pr_err().

Done with the help of Coccinelle, excluing tools/ directory.

The semantic patch I used is as follows:

// <smpl>
@@@@
-error
+pr_err
 (...)
// </smpl>

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-04 11:59:44 -04:00
Kever Yang
a27290a6f8 rockchip: rk3188: ram: add support for 16bit row address
RK3188 using the same ddr_conf for both 15 bit and 16 bit row address.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Fixed compile-error by declaring 'row':]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:32 +02:00
Kever Yang
0176399b79 rockchip: rk322x: add sdram driver
Add driver for rk322x to support sdram initialize in SPL.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:32 +02:00
Kever Yang
f0768491db rockchip: rk3328: move sdram driver to driver/ram
Since we have CONFIG_RAM framwork and its driver folder, move the driver
into it.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:31 +02:00
Kever Yang
c9eb7bca4b rockchip: rk3288: move sdram driver to driver/ram
Since we have CONFIG_RAM framwork and its driver folder, move the driver
into it.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:31 +02:00
Kever Yang
5b67d7010b rockchip: rk3188: move sdram driver to driver/ram
Since we have CONFIG_RAM framwork and its driver folder, move the driver
into it.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:31 +02:00
Kever Yang
b5934cf67c rockchip: rk3399: move sdram driver to driver/ram
Since we have CONFIG_RAM framwork and its driver folder, move the driver
into it.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:31 +02:00
Philipp Tomsich
1d70f0ac88 rockchip: rk3368: adjust DMC driver for 32/64bit-aware OF_PLATDATA
With the new 32/64bit-aware dtoc, the type of reg is fdt64_t and the
OF_PLATDATA structure layout changes.  This adjusts the DMC driver for
the RK3368 to track these changes.

For the time being (i.e. until regmap_init_mem_platdata works for the
64bit case), we won't use regmap_init_mem_platdata here and simply
access of_plat.reg[] directly.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-18 20:40:38 +02:00
Jagan Teki
93fd5b0ac1 ram: kconfig: s/SPL/TPL/ in TPL_RAM help text
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-08-26 14:56:06 -04:00
Philipp Tomsich
403e9cbcd5 rockchip: rk3368: add DRAM controller driver with DRAM initialisation
This adds a DRAM controller driver for the RK3368 and places it in
drivers/ram/rockchip (where the other DM-enabled DRAM controller
drivers for rockchip devices should also be moved eventually).

At this stage, only the following feature-set is supported:
 - DDR3
 - 32-bit configuration (i.e. fully populated)
 - dual-rank (i.e. no auto-detection of ranks)
 - DDR3-1600K speed-bin

This driver expects to run from a TPL stage that will later return to
the RK3368 BROM.  It communicates with later stages through the
os_reg2 in the pmugrf (i.e. using the same mechanism as Rockchip's DDR
init code).

Unlike other DMC drivers for RK32xx and RK33xx parts, the required
timings are calculated within the driver based on a target frequency
and a DDR3 speed-bin (only the DDR3-1600K speed-bin is support at this
time).

The RK3368 also has the DDRC0_CON0 (DDR ch. 0, control-register 0)
register for controlling the operation of its (single-channel) DRAM
controller in the GRF block.  This provides for selecting DDR3, mobile
DDR modes, and control low-power operation.
As part of this change, DDRC0_CON0 is also added to the GRF structure
definition (at offset 0x600).

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-13 17:12:33 +02:00
Philipp Tomsich
c336c3c35f spl: dm: Kconfig: introduce TPL_RAM (in analogy to SPL_RAM)
To allow finer grained selection of features for TPL, we introduce
TPL_RAM (in analogy to SPL_RAM).

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-08-13 17:12:20 +02:00
Philipp Tomsich
45233301b6 spl: dm: Kconfig: SPL_RAM depends on SPL_DM
This commit models the dependency from SPL_RAM to SPL_DM in Kconfig.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-08-13 17:12:20 +02:00
Patrice Chotard
7016651eac ram: stm32: add stm32h7 support
STM32F7 and H7 shared the same SDRAM control block.
On STM32H7 few control bits has been added.
The current driver need some minor adaptation as FMC block
enable/disable for H7.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-07-26 11:29:15 -04:00
Patrice Chotard
f303aaf21b ram: stm32: add second SDRAM bank management
FMC is able to manage 2 SDRAM banks, but the current driver
implementation is only able to manage the first SDRAM bank.

Even if only bank2 is used, some bank1 registers must be
configured.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-07-26 11:29:15 -04:00
Patrice Chotard
f39b90dc8c ram: stm32: replace fdtdec_get by ofnode calls
Replace all fdtdec_get..() calls by ofnode_read...() or dev_read..().
This will allow drivers to support a live device tree.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-07-26 11:29:14 -04:00
Patrice Chotard
1421e0a375 ram: stm32: get base address from DT
Retrieve RAM base address from DT instead of using STM32_SDRAM_FMC

For STM32F7, FMC block base address is 0xA0000000, but SDRAM
registers are located at offset 0x140 inside FMC block.
Update the stm32_fmc_regs fields with all FMC registers
to map SDRAM registers at the right address.

These additionals registers will be used later.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-07-26 11:29:14 -04:00
Patrice Chotard
9242ece12b ram: stm32: migrate fmc defines in driver file
Migrate all FMC defines from arch/arm/include/asm/arch-stm32f7/fmc.h
to drivers/ram/stm32_sdram.c

This will avoid to add an additionnal arch-stm32xx/fmc.h file when
a new stm32 family soc will be introduced.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-07-26 11:29:07 -04:00
Patrice Chotard
14a50e3736 drivers: ram: stm32: fix compilation issue
If CONFIG_CLK flag is not set, compilation raises the
following error message:

drivers/ram/stm32_sdram.c: In function 'stm32_fmc_probe':
drivers/ram/stm32_sdram.c:154:2: error: 'ret' undeclared (first use in this function)
  ret = stm32_sdram_init(dev);

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
cc: Vikas Manocha <vikas.manocha@st.com>
2017-06-05 14:13:13 -04:00