Add a test for the MMC load method. This shows the general shape of tests
to come: The main test function calls do_spl_test_load with an appropriate
callback to write the image to the medium.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add some functions for creating fat/ext2 filesystems with a single file and
a test for them. Filesystems require block devices, and it is easiest to
just use MMC for this. To get an MMC, we must also pull in the test device
tree. SPL_TIMER is necessary for SPL_MMC, perhaps because it uses a timeout.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This add some basic functions to create images, and a test for said
functions. This is not intended to be a test of the image parsing
functions, but rather a framework for creating minimal images for testing
load methods. That said, it does do an OK job at finding bugs in the image
parsing directly.
Since we have two methods for loading/parsing FIT images, add LOAD_FIT_FULL
as a separate CI run.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Several SPL functions try to avoid performing initialization twice by
caching devices. This is fine for regular boot, but does not work with
UNIT_TEST, since all devices are torn down after each test. Add some
functions to invalidate the caches which can be called before testing these
load methods.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Add various defines which are not necessary for reading/writing
filesystems, but which are useful for creating them. These mostly come from
Linux v6.5-rc2 (what I had checked out).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make sure we have an IMX header before calling spl_load_imx_container,
since if we don't it will fail with -ENOENT. This allows us to fall back to
legacy/raw images if they are also enabled.
This is a functional change, one which likely should have been in place
from the start, but a functional change nonetheless. Previously, all
non-IMX8 images (except FITs without FIT_FULL) would be optimized out if
the only image load method enabled supported IMX8 images. With this change,
support for other image types now has an effect.
There are seven boards with SPL_LOAD_IMX_CONTAINER enabled: three with
SPL_BOOTROM_SUPPORT:
imx93_11x11_evk_ld imx93_11x11_evk imx8ulp_evk
and four with SPL_MMC:
deneb imx8qxp_mek giedi imx8qm_mek
All of these boards also have SPL_RAW_IMAGE_SUPPORT and
SPL_LEGACY_IMAGE_FORMAT enabled as well. However, none have FIT support
enabled. Of the six load methods affected by this patch, only SPL_MMC and
SPL_BOOTROM_SUPPORT are enabled with SPL_LOAD_IMX_CONTAINER.
spl_romapi_load_image_seekable does not support legacy or raw images, so
there is no growth. However, mmc_load_image_raw_sector does support loading
legacy/raw images. Since these images could not have been booted before, I
have disabled support for legacy/raw images on these four boards. This
reduces bloat from around 800 bytes to around 200.
There are no in-tree boards with SPL_LOAD_IMX_CONTAINER and AHAB_BOOT both
enabled, so we do not need to worry about potentially falling back to
legacy images in a secure boot scenario.
Future work could include merging imx_container.h with imx8image.h, since
they appear to define mostly the same structures.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Introduce two new weak functions, arch_spl_mmc_get_uboot_raw_sector() and
board_spl_mmc_get_uboot_raw_sector(), each of which can be overridden at
a matching level, that is arch/ and board/ , in addition to the existing
weak function spl_mmc_get_uboot_raw_sector().
This way, architecture code can define a default architecture specific
implementation of arch_spl_mmc_get_uboot_raw_sector(), while the board
code can override that using board_spl_mmc_get_uboot_raw_sector() which
takes precedence over the architecture code. In some sort of unlikely
special case where code has to take precedence over board code too, the
spl_mmc_get_uboot_raw_sector() is still left out to be a weak function,
but it should be unlikely that this is ever needed to be overridden.
Signed-off-by: Marek Vasut <marex@denx.de>
The Renesas RZ/G2L SMARC Evaluation Board Kit consists of the RZ/G2L
System-on-Module (SOM) based on the R9A07G044L2 SoC, and a common SMARC
carrier board.
The ARM TrustedFirmware code for the Renesas RZ/G2L SoC family passes a
devicetree blob to the bootloader as an argument in the same was
previous R-Car gen3/gen4 SoCs. This blob contains a compatible string
which can be used to identify the particular SoC we are running on and
this is used to select the appropriate device tree to load.
The configuration renesas_rzg2l_smarc_defconfig is added to support
building for this target. In the future this defconfig will be extended
to support other SoCs and evaluation boards from the RZ/G2L family.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add board-specific function used to indicate whether a DTO from fitImage
configuration node 'fdt' property DT and DTO list should be applied onto
the base DT or not applied.
This is useful in case of DTOs which implement e.g. different board revision
details, where such DTO should be applied on one board revision, and should
not be applied on another board revision.
Signed-off-by: Marek Vasut <marex@denx.de>
In order to be able to discard unused long help texts without further
linker lists, add a macro for defining the long help messages which uses
__maybe_unused. This allows us to discard them as unreferenced as part
of the link.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver adds support for the pinctrl features of the GPIO/PFC module
in the Renesas RZ/G2L (R9A07G044) SoC.
A multi-function `rzg2l-pfc` driver is defined for UCLASS_NOP, which
binds the `rzg2l-pfc-pinctrl` UCLASS_PINCTRL driver dynamically. We also
define common macros and functions for the PFC in <renesas/rzg2l-pfc.h>.
This makes it easy to add an additional UCLASS_GPIO driver for the GPIO
functionality of this module in a follow-up patch.
This patch is based on the corresponding Linux v6.5 driver
(commit 52e12027d50affbf60c6c9c64db8017391b0c22e).
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Import bindings for the Interrupt Controller (IRQC) module in the
Renesas RZ/G2L SoC family.
This patch is based on the dt-bindings in Linux v6.5
(commit 52e12027d50affbf60c6c9c64db8017391b0c22e).
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Import bindings for the Port Function Control (PFC) module in the
Renesas RZ/G2L SoC family.
This patch is based on the dt-bindings in Linux v6.5
(commit 52e12027d50affbf60c6c9c64db8017391b0c22e).
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Import bindings for the Clock Pulse Generator (CPG) module in the
Renesas RZ/G2L SoC family.
This patch is based on the dt-bindings in Linux v6.5
(commit 52e12027d50affbf60c6c9c64db8017391b0c22e).
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add i.MX93 CCF driver support.
Modifed from Linux Kernel v6.5-rc2 and adapted for U-Boot.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
ZyXEL NSA325 specifications:
Marvell Kirkwood 88F6282 SoC
1.6 GHz CPU
1x GBE LAN port (Marvell MV88E1318)
512 MB RAM
128 MB Eon NAND, SLC
I2C
1x USB 3.0 (on PCIe bus)
2x USB 2.0
2x SATA (hot swap slots)
Serial console
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The bootcmd_mfg env variable is legacy from IMX downstream u-boot branch
and is not needed on mainline.
Signed-off-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Drop unused code related to CONFIG_TDX_EASY_INSTALLER, that existed only on
toradex downstream branch.
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This patch adds an implementation of the Meson Secure Monitor
driver based on UCLASS_SM.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230921081346.22157-7-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
At the moment, we don't have a common API for working with
SM, only the smc_call() function. This approach is not generic
and difficult to configure and maintain.
This patch adds UCLASS_SM with the generic API:
- sm_call()
- sm_call_write()
- sm_call_read()
These functions operate with struct pt_regs, which describes
Secure Monitor arguments.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230921081346.22157-2-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
scan all entries in multi-device boot_targets
EFI empty-capsule support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmUpvTQRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreabCwgAimB2fGpK3FjFMrH1Ko4Qh3j0D/0XomiQ
1KYVbn3YrswLmq1tav9HSKWR3Ep/Uet6jthpH2RPxhcGWNGqxkkk2k4LUudSlIYd
0KKoovMwBK9jZcojoBAjFGaoRIaEBlbFspW/RoXPJnr7ctxf6HSYkW2TPH09zqtD
FrL5Jjf6t0h6QShxhCYXbiHGCnp2zYZRzFnrYpaXy8IIavqWNJTAhkIGveMy+Qa8
TzhmuRamLgtZZwtFcHt8sZuV4+FtBrtHAyiEasnJFPJ5Kv6tFVBiHdYuygZMu/og
+F57ufgqgHTlDjzW72CJyhrHIcVn/mWjNYrulufqHAsSFD7cizISeA==
=qOUT
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-13oct23' of https://source.denx.de/u-boot/custodians/u-boot-dm
improvements with dev_read_addr_..._ptr()
scan all entries in multi-device boot_targets
EFI empty-capsule support
SCMI base protocol is mandatory, and once SCMI node is found in a device
tree, the protocol handle (udevice) is unconditionally installed to
the agent. Then basic information will be retrieved from SCMI server via
the protocol and saved into the agent instance's local storage.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
SCMI base protocol is mandatory according to the SCMI specification.
With this patch, SCMI base protocol can be accessed via SCMI transport
layers. All the commands, except SCMI_BASE_NOTIFY_ERRORS, are supported.
This is because U-Boot doesn't support interrupts and the current transport
layers are not able to handle asynchronous messages properly.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
This framework allows SCMI protocols to be installed and bound to the agent
so that the agent can manage and utilize them later.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
SCMI specification allows any protocol to have its own channel for
the transport. While the current SCMI driver may assign its channel
from a device tree, the core function, devm_scmi_process_msg(), doesn't
use a protocol's channel, but always use an agent's channel.
With this commit, devm_scmi_process_msg() tries to find and use
a protocol's channel. If it doesn't exist, use an agent's.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The commit 85dc582892 ("firmware: scmi: prepare uclass to pass channel
reference") added an explicit parameter, channel, but it seems to make
the code complex.
Hiding this parameter will allow for adding a generic (protocol-agnostic)
helper function, i.e. for PROTOCOL_VERSION, in a later patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
Same as dev_read_addr_name[_size](), but returns a pointer, cast
through map_sysmem().
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Checking for the error cast to fdt_addr_t is rather awkward - IS_ERR()
can be used, but it's not really made to be used on fdt_addr_t, which
may not even be the same size as a native pointer.
Most places in U-Boot only check for FDT_ADDR_T_NONE; let's adjust the
error return to match the expectation.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- The dev_read_addr_name*() family of functions has no "index" argument,
doc comments should refer to "name"
- Specify the error return for several devfdt_get_addr*() functions
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Documentation:
* Bump urllib3 version
* Migrate Renesas board docs to rst
* Link an introduction video
UEFI
* Use same GUID as EDK II for auto-created boot options
* Clean up BitBlt test
-----BEGIN PGP SIGNATURE-----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=vtF1
-----END PGP SIGNATURE-----
Merge tag 'efi-2024-01-rc1' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request efi-2024-01-rc1
Documentation:
* Bump urllib3 version
* Migrate Renesas board docs to rst
* Link an introduction video
UEFI
* Use same GUID as EDK II for auto-created boot options
* Clean up BitBlt test
clk:
- remove additional compatible strings for Versal NET
net:
- zynq_gem: Fix clock calculation for MDC for higher frequencies
pinctrl:
- core: Extend pinmux status buffere size
- zynqmp driver: Show also tristate configuration
test:
- add test case for pxe get
Xilinx:
- describe SelectMAP boot mode
Zynq:
- Fix nand description in DT
ZynqMP:
- DTS sync patches with kernel and also W=1 related fixes
- Add support for KD240, zcu670, e-a2197 with x-prc cards, SC revB/C with i2c
description for other SC based boards
- k24 psu_init cleanup
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZSjvwAAKCRDKSWXLKUoM
IR34AJ92oum3pJXKxKREEZh0dCfDvJlE/wCggyzxI2T5liJfRG5jzlUuDjiLLU0=
=u1bz
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2024.01-rc1-v3' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2024.01-rc1 v3
clk:
- remove additional compatible strings for Versal NET
net:
- zynq_gem: Fix clock calculation for MDC for higher frequencies
pinctrl:
- core: Extend pinmux status buffere size
- zynqmp driver: Show also tristate configuration
test:
- add test case for pxe get
Xilinx:
- describe SelectMAP boot mode
Zynq:
- Fix nand description in DT
ZynqMP:
- DTS sync patches with kernel and also W=1 related fixes
- Add support for KD240, zcu670, e-a2197 with x-prc cards, SC revB/C with i2c
description for other SC based boards
- k24 psu_init cleanup
This adds more supported spinand devices from the Linux kernel
implementation.
This does not include the latest kernel implementation as this would
require a substantial amount of extra work due to the missing
ECC engine abstraction layer in U-Boot.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> (commit message)
Link: https://lore.kernel.org/all/20230110115843.391630-3-frieder@fris.de
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Currently there are 3 different variants of read_id implementation:
1. opcode only. Found in GD5FxGQ4xF.
2. opcode + 1 addr byte. Found in GD5GxGQ4xA/E
3. opcode + 1 dummy byte. Found in other currently supported chips.
Original implementation was for variant 1 and let detect function
of chips with variant 2 and 3 to ignore the first byte. This isn't
robust:
1. For chips of variant 2, if SPI master doesn't keep MOSI low
during read, chip will get a random id offset, and the entire id
buffer will shift by that offset, causing detect failure.
2. For chips of variant 1, if it happens to get a devid that equals
to manufacture id of variant 2 or 3 chips, it'll get incorrectly
detected.
This patch reworks detect procedure to address problems above. New
logic do detection for all variants separatedly, in 1-2-3 order.
Since all current detect methods do exactly the same id matching
procedure, unify them into core.c and remove detect method from
manufacture_ops.
This is a rework of Chuanhong Guo <gch981213@gmail.com> patch
submitted to linux kernel
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/all/20230110115843.391630-1-frieder@fris.de
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Switch to using bootstd. Note with this change, we will stop using
distro_bootcmd and instead depend entirely on bootflow method of
starting the system up.
Drop header files that are no longer needed in am64x_evm.h.
k3_dfu.h is available via k3_dfu.env in am64x.env.
Drop unused macro CFG_SYS_SDRAM_BASE1.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Add clock bindings for Amlogic A1 from linux-next next-20230821.
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230925155209.130671-2-ivprusov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The boot option automatically created by efibootmgr is identified
by the special guid appended in the optional data of boot option.
The same mechanism is implemented in the EDK II reference
implementation, it uses the different guid from the one currently
U-Boot uses.
The guid indicating auto-created boot option is not defined in the
UEFI specification, but some userspace tools such as 'efivar' package
are aware of the guid used in EDK II as auto-created boot option.
So let's use the same guid as EDK II reference implementation.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
At present cedit only supports menu keys. For textline objects we need
to insert normal ASCII characters.
We also need to handle backspace, which is ASCII 9.
In fact, expo does not make use of all the menu keys, so partition
them accordingly and update the logic to support normal ASCII
characters, too.
Signed-off-by: Simon Glass <sjg@chromium.org>
A textline is a line of text which can be edited by the user. It has a
maximum length (in chracters) but otherwise there are no restrictions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add the CLI state, a buffer to hold the old value of the text being
edited and a place to save vidconsole entry context. These will be use
by the textline object.
Set an upper limit on the maximum number of characters in a textline
object supported by expo, at least for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
So far only menus can be highlighted. With the coming addition of
text lines we need to be able to highlight other objects. Add a function
to determine whether an object can be highlighted.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add rudimentary support for displaying a cursor on a vidconsole. This
helps the user to see where text is being entered.
The implementation so far is very simple: the cursor is just a vertical
bar of fixed width and cannot be erased. To erase the cursor, the text
must be redrawn over it.
This is good enough for expo but will need enhancement to be useful for
the command-line console. For example, it could save and restore the
area behind the cursor.
For now, enable this only for expo, to reduce code size.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this is called only when a newline is detected, since this
indicates the start of a line of text being entered.
Export this function so it can be used by expo, which may start a new
text line itself, without first writing out a newline.
Signed-off-by: Simon Glass <sjg@chromium.org>
Text entry operates within a context which includes quite a bit of
information. For example, with Truetype fonts, each character in the
text string has a position stored, so that it is possible to
backspace to that character. This information is built up as strings
are drawn on the display.
For the command line, there is just a single context. It is created
when command-line entry starts and it is destroyed (or at least not
needed anymore) when the user presses <enter> to enter the command.
By contrast, expo needs to be able to switch in and out of a text-entry
context, since it is also displaying other objects in the scene.
Add a way to save and restore the entry context for a vidconsole. This
is only needed for the truetype vidconsole, so add a method for that,
storing the information in an abuf struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present there is a method for measuring text, but if the actual text
string is not known, it cannot be used.
For text editor we want to set the size of the entry box to cover the
expected text size. Add the concept of a 'norminal' size with a method
to calculate that for the vidconsole.
If the method is not implemented, fall back to using the font size,
which is sufficient for fixed-width fonts.
Signed-off-by: Simon Glass <sjg@chromium.org>
When inputting text outside the command line we don't want to use tab
for command completion. Add an option to control this.
Signed-off-by: Simon Glass <sjg@chromium.org>
When inputting text outside the command line we don't want history to be
accessible. Add an option to control this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move most of the inner loop from cread_line() into a new function. This
will allow using it from other code.
This involves adding a few more members to the state struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to reuse the editing code elsewhere. As a first step, move the
common variables into a struct. This will allow us to eventually put the
contents of the inner loop in a function, so it can be called from
elsewhere.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is a function for this but it is never used. Showing the history is
a useful feature, so add a new 'history' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
As the code to switch an ARM core from secure to the non-secure state
needs to know the base address of the Generic Interrupt Controller
(GIC), we read an Arm Cortex defined system register that is supposed to
hold that base address. However there are SoCs out there that get this
wrong, and this CBAR register either reads as 0 or points to the wrong
address. To accommodate those systems, so far we use a macro defined in
some platform specific header files, for affected boards.
To simplify future extensions, replace that macro with a Kconfig variable
that holds this override address, and define a default value for SoCs
that need it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sam Edwards <CFSworks@gmail.com>
Fix up remaining occurances of EVENT_SPY with no suffix.
Fixes: 6c4cad7438 ("event: Rename EVENT_SPY to EVENT_SPY_FULL")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added new xenguest_arm64_virtio_defconfig which
enables support for virtio-blk using various types
of transport like virtio-pci, vrtio-mmio. Currently
supported: up to 2 PCI host bridges and 10 MMIO devices.
Note: DT parsing code was partly taken from pci-uclass.c
Limitation: All memory regions should be
below 4GB address space.
Signed-off-by: Andrii Chepurnyi <andrii_chepurnyi@epam.com>
blk_{read,write}_devnum() are no longer used by anywhere in the
source tree. Drop them.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
get_desc() can be useful outside blk-uclass.c. Let's change it to
an API and make it externally visible.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Allow optionally set the logical block size of the host device to
bind in the "host bind" command. If not given, defaults to 512.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Add support for declaring in device tree the reserved memory ranges
required for MC. Since the MC firmware acts as any DMA master present
in the SoC, the reserved memory ranges need also be identity mapped
in the SMMU, so create the required 'iommu-addresses' property in
the reserved memory nodes.
For now this support is used only on LX2160A SoCs.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
PPA was a secure firmware developed in-house which is no longer
supported and replaced by TF-A quite some years ago. Drop support
for it.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When copying the name of a stdio device we must ensure that it is NUL
terminated before passing it to strcmp() to avoid a buffer overrun.
Truncating the name field leads to failure to deregister a stdio device.
When copying we must ensure that the name field sizes match.
Addresses-Coverity-ID: 350462 String not null terminated
Fixes: 5294e97832 ("stdio: extend "name" to 32 symbols")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
spl_invoke_atf function will not be returned to SPL. Thus, we need to
set __noreturn function attribute to the function.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
For Xilinx ZynqMP SOC new parameter was added and now it can
set 7 parameters for its pins. Pinmux status command will
print the status of these parameters for each pin. But
current print buffer length is only 80 characters long, increase it
to 90 to print all the parameters without truncation.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230920030006.6488-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
- Add Board: rk3568 Bananapi R2Pro;
- Update pcie bifurcation support;
- dwc_eth_qos controller support for rk3568 and rk3588;
- Compressed binary support for U-Boot on rockchip platform;
- dts and config updates for different board and soc;
[ trini: Fix conflict on include/spl.h ]
Signed-off-by: Tom Rini <trini@konsulko.com>
all rk3308 boards should use their own dtb file.
also, change fdt_addr_r to avoid following error:
"ERROR: Did not find a cmdline Flattened Device Tree"
it happens on Radxa ROCK Pi S (256MB/512MB) with kernel built from
Radxa BSP.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Sync the device tree for RK3588 series with Linux 6.6-rc1.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
If LZMA Compression support is enabled, LZMA compressed U-Boot
binary will be placed at a specified RAM location which is
defined at CONFIG_SYS_LOAD_ADDR and will be assigned as the
source address.
image_decomp() function, will decompress the LZMA compressed
U-Boot binary which is placed at source address(CONFIG_SYS_LOAD_ADDR)
to the default CONFIG_SYS_TEXT_BASE location.
spl_load_fit_image function will load the decompressed U-Boot
binary, which is placed at the CONFIG_SYS_TEXT_BASE location.
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If GZIP Compression support is enabled, GZIP compressed U-Boot binary
will be at a specified RAM location which is defined at
CONFIG_SYS_LOAD_ADDR and will be assign it as the source address.
gunzip function in spl_load_fit_image ,will decompress the GZIP
compressed U-Boot binary which is placed at
source address(CONFIG_SYS_LOAD_ADDR) to the default
CONFIG_SYS_TEXT_BASE location.
spl_load_fit_image function will load the decompressed U-Boot
binary, which is placed at the CONFIG_SYS_TEXT_BASE location.
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter"), keeping regulator enablement in balance become more important.
Calling regulator_autoset multiple times on a fixed regulator increase
the enable count for each call, resulting in an unbalanced enable count.
Introduce a AUTOSET_DONE flag and use it to mark that autoset has run
for the regulator. Return -EALREADY on any subsequent call to autoset.
This fixes so that the enable count is only ever increased by one per
regulator for autoset.
Fixes: 4fcba5d556 ("regulator: implement basic reference counter")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The PCI helpers read only the base address for a PCI region. In some cases
the size is needed as well, e.g. to pass along to a driver which needs to
know the size of its register area.
Update the functions to allow the size to be returned. For serial, record
the information and provided it with the serial_info() call.
A limitation still exists in that the size is not available when OF_LIVE
is enabled, so take account of that in the tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function cannot return true if PCI is not enabled, since no PCI
devices will have been bound. Add a check for this to reduce code size
where it is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
The spl_phase() function indicates whether U-Boot is in SPL and before
or after relocation. But sometimes it is useful to check for SPL with
zero code-size impact. Since spl_phase() checks the global_data flags,
it does add a few bytes.
Add a new spl_in_proper() function to check if U-Boot proper is
running, regardless of the relocation status.
Signed-off-by: Simon Glass <sjg@chromium.org>
This uses ARRAY_SIZE() but does not include the header file which declares
it. Fix this, so that command.h can be included without common.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Typically the bloblist is set up after the devicetree is present. This
makes sense because bloblist may use malloc() to allocate the space it
needs.
However sometimes the devicetree itself may be present in the bloblist.
In that case it is at a known location in memory so we can init the
bloblist very early, before devicetree.
Add a flag to indicate whether the bloblist has been inited. Add a
function to init it only if needed. Use that in the init sequence.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for writing a single 64-bit value into a property.
Repurpose the existing tests to handle this case too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add functions to write a boolean property. This involves deleting it if
the value is false.
Add a new ofnode_has_property() as well. Add a comment about the behaviour
of of_read_property() when the property value is empty.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a way to flatten a devicetree into binary form. For livetree this
involves generating the devicetree using fdt_property() and other calls.
For flattree it simply involves providing the buffer containing the tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function to copy a node to another place under a new name. This is
useful at least for testing, since copying a test node with existing
properties is easier than writing the code to generate it all afresh.
Signed-off-by: Simon Glass <sjg@chromium.org>
For some reason this code was put in the main spl.c file. Move it out
to the FIT implementation where it belongs.
Signed-off-by: Simon Glass <sjg@chromium.org>
This feature has some helpers in its header file so that its functions
resolve to nothing when the feature is disabled. Add a few more and use
these to simplify the code.
With this there are no more #ifdefs in board_init_r()
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the new SPL/TPL/VPL_SYS_MALLOC_F symbols to determine whether the
malloc pool exists.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
This code is pretty ugly, with many #ifdefs
There are quite a lot of IH_OS_U_BOOT values so the compiler struggles
to create a jump table here. Also, most of the options are normally
disabled.
Change it to an else...if construct instead. Add an accessor for the
spl_image field behind an #ifdef to avoid needing #ifdef in the C code.
Signed-off-by: Simon Glass <sjg@chromium.org>