Commit graph

212 commits

Author SHA1 Message Date
Dario Binacchi
165e8fe5db clk: ti: add am33xx/am43xx spread spectrum clock support
The patch enables spread spectrum clocking (SSC) for MPU and LCD PLLs.
As reported by the TI spruh73x/spruhl7x RM, SSC is only supported for
the DISP/LCD and MPU PLLs on am33xx/am43xx. SSC is not supported for
DDR, PER, and CORE PLLs.

Calculating the required values and setting the registers accordingly
was taken from the set_mpu_spreadspectrum routine contained in the
arch/arm/mach-omap2/am33xx/clock_am33xx.c file of the u-boot project.

In locked condition, DPLL output clock = CLKINP *[M/N]. In case of
SSC enabled, the reference manual explains that there is a restriction
of range of M values. Since the clk_ti_am3_dpll_round_rate() attempts
to select the minimum possible N, the value of M obtained is not
guaranteed to be within the range required. With the new "ti,min-div"
parameter it is possible to increase N and consequently M to satisfy the
constraint imposed by SSC.

Link: https://lore.kernel.org/r/20210606202253.31649-6-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
2021-10-11 14:27:32 -04:00
Wolfgang Denk
0a50b3c97b WS cleanup: remove trailing white space
Signed-off-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-09-30 08:08:56 -04:00
Tom Rini
a2ac2b964b Convert CONFIG_SKIP_LOWLEVEL_INIT et al to Kconfig
This converts the following to Kconfig:
   CONFIG_SKIP_LOWLEVEL_INIT
   CONFIG_SKIP_LOWLEVEL_INIT_ONLY

In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-31 17:47:49 -04:00
Moses Christopher
050531db00 am335x, guardian: mem: Add board dependent mem values
- Add mem-guardian.h derived from am33xx/mem.h

    * Add GPMC config values optimized for Bosch Guardian Board
    * NAND Chip used by Bosch Guardian Board is Micron MT29F4G08ABBFA

Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210611161350.2141-3-Gireesh.Hiremath@in.bosch.com
2021-07-15 17:56:03 +05:30
Dario Binacchi
9d76120083 arm: ti: am33xx: add DPLL_EN_FAST_RELOCK_BYPASS macro
Add missing DPLL_EN_FAST_RELOCK_BYPASS macro. Used to put the DPLL in
idle bypass fast relock mode.

Signed-off-by: Dario Binacchi <dariobin@libero.it>
2021-01-12 10:58:04 +05:30
Simon Glass
cd93d625fd common: Drop linux/bitops.h from common header
Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 21:19:23 -04:00
Simon Glass
c3dc39a2f8 arm: Don't include common.h in header files
It is bad practice to include common.h in other header files since it can
bring in any number of superfluous definitions. It implies that some C
files don't include it and thus may be missing CONFIG options that are set
up by that file. The C files should include these themselves.

Update some header files in arch/arm to drop this.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 14:54:24 -04:00
Sjoerd Simons
f50939647c Add support for the MT41K128M16JT125K memory modules
Add configuration for the MT41K128M16JT125K memory modules as used on the
Bosch Guardian device.

Based on a patch by:
    Govindaraji Sivanantham <Govindaraji.Sivanantham@in.bosch.com>

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
[checkpatch.pl cleanup by Martyn Welch]
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
2019-04-12 08:05:48 -04:00
Abel Vesa
79536013a3 usb: Rename SPL_USB_SUPPORT to SPL_USB_STORAGE
Since there is the SPL_USB_HOST_SUPPORT for enabling USB support in SPL,
makes more sense to rename the SPL_USB_SUPPORT as SPL_USB_STORAGE.
Everything that is not part of the usb storage support in SPL is now
build under SPL_USB_HOST_SUPPORT.

Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-02-15 22:01:15 +01:00
Jean-Jacques Hiblot
5f97ae6814 i2c: omap24xx_i2c: Use platdata to probe the device
This allows the driver to be used without OF_CONTROL.
AM335x support DM_SPL but does not use SPL_OF_CONTROL. Enabling DM_I2C in
SPL thus requires that the omap I2C can be passed platdata.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2018-12-10 06:11:18 +01:00
Vignesh R
bca09ce4b0 i2c: omap24xx_i2c: Move away from SoC specific headers for reg offset
Move away from SoC specific headers to handle different register layout.
Instead use driver data to get appropriate register layouts like in the
kernel. While at it, perform some mostly cosmetic alignment/cleanup in
the functions being updated.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2018-12-10 06:09:34 +01:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Russ Dill
025a0d40e1 ARM: am33xx: Inhibit re-initialization of DDR during RTC-only
This inhibits the re-inititialization of DDR during an RTC-only resume. If
this is not done, an L3 NOC error is produced as the DDR gets accessed
before the re-init has time to complete. Tested on AM437x GP EVM.

Signed-off-by: Russ Dill <Russ.Dill@ti.com>
[j-keerthy@ti.com Ported to Latest Master branch]
Signed-off-by: Keerthy <j-keerthy@ti.com>
2018-04-06 17:04:33 -04:00
Tero Kristo
7619badb9c ARM: AM43xx: Add support for RTC only + DDR in self-refresh mode
Kernel stores information to the RTC_SCRATCH0 and RTC_SCRATCH1 registers
for wakeup from RTC-only mode with DDR in self-refresh. Parse these
registers during SPL boot and jump to the kernel resume vector if the
device is waking up from RTC-only modewith DDR in Self-refresh.

The RTC scratch register layout used is:

SCRATCH0 : bits00-31 : kernel resume address
SCRATCH1 : bits00-15 : RTC magic value used to detect valid config
SCRATCH1 : bits16-31 : board type information populated by bootloader

During the normal boot path the SCRATCH1 : bits16-31 are updated with
the eeprom read board type data. In the rtc_only boot path the rtc
scratchpad register is read and the board type is determined and
correspondingly ddr dpll parameters are set. This is done so as to avoid
costly i2c read to eeprom.

RTC-only +DRR in self-refresh mode support is currently only enabled for
am43xx_evm_rtconly_config.
This is not to be used with epos evm builds.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
[j-keerthy@ti.com Rebased to latest u-boot master branch]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-04-06 17:04:33 -04:00
Jean-Jacques Hiblot
f844d5f4e6 omap: Update the base address of the MMC controllers
Align the base address defined in header files with the base address used
in the DTS. This will facilitate the introduction of the DMA support.

Of all HSMMC users, only omap3 doesn't have the 0x100 reserved region at
the top. This region will be used to determine if the controller supports
DMA transfers

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-01-18 22:04:21 -05:00
Hannes Schmelzer
3215192922 mach-omap2: add AM335x Display PLL register definition
Adds the register definition of the Display DPLL

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
2018-01-11 15:16:34 +01:00
Landheer-Cieslak, Ronald
48c7f77128 Add UART base addresses for additional UARTs
UARTs 1 through 5 were missing in the code - added.
Also pick the default according to the configuration setting for the
console index.

Signed-off-by: Ronald Landheer-Cieslak <ronaldlandheercieslak@eaton.com>
2017-11-17 10:53:45 -05:00
Felix Brack
c07bf9bea7 am33xx: Add a function to query MPU voltage in uV
For the DM TPS65910 driver I'm working on, querying the MPU voltage
should return a value in uV. This value can then be used by the
regulator's standard function set_value to set the MPU voltage.

Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-11-17 07:43:32 -05:00
Adam Ford
fc760cc6e8 Convert CONFIG_SYS_I2C_BUS_MAX to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_I2C_BUS_MAX

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Fix AM43XX drop AM44XX]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-09-01 20:44:30 -04:00
Adam Ford
ac1d8ac871 Configs: Migrate I2C_BUS_MAX to CONFIG_SYS_I2C_BUS_MAX
For consistency with other platforms and in preparation of Kconfig
migration, let's change Several TI platforms that use I2C_BUS_MAX
to CONFIG_SYS_I2C_BUS_MAX

Signed-off-by: Adam Ford <aford173@gmail.com>
2017-09-01 17:56:20 -04:00
Tom Rini
de8203653f ti816x: Enable ethernet support
The ti816x SoC revision of the ethernet IP block is handled by the
"davinci_emac" driver, rather than the "cpsw" driver as done by later
members of the family.  Enable the relevant plumbing.

Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-28 11:43:39 -04:00
Semen Protsenko
00bbe96eba arm: omap: Unify get_device_type() function
Refactor OMAP3/4/5 code so that we have only one get_device_type()
function for all platforms.

Details:
 - Add ctrl variable for AM33xx and OMAP3 platforms (like it's done for
   OMAP4/5), so we can obtain status register in common way
 - For now ctrl structure for AM33xx/OMAP3 contains only status register
   address
 - Run hw_data_init() in order to assign ctrl to proper structure
 - Remove DEVICE_MASK and DEVICE_GP definitions as they are not used
   (DEVICE_TYPE_MASK and GP_DEVICE are used instead)
 - Guard structs in omap_common.h with #ifdefs, because otherwise
   including omap_common.h on non-omap4/5 board files breaks compilation

Buildman script was run for all OMAP boards. Result output:
    arm: (for 38/616 boards)
        all +352.5
        bss -1.4
        data +3.5
        rodata +300.0
        spl/u-boot-spl:all +284.7
        spl/u-boot-spl:data +2.2
        spl/u-boot-spl:rodata +252.0
        spl/u-boot-spl:text +30.5
        text +50.4
    (no errors to report)

Tested on AM57x EVM and BeagleBoard xM.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Rework the guards as to not break TI81xx]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-09 20:34:53 -04:00
Tom Rini
8bb687fdc1 t81xx: Migrate TI81XX/TI816X/TI814X symbols to Kconfig
The symbol CONFIG_TI81XX is used for the parts that are common to the
TI816x and TI814x SoCs and are not part of CONFIG_ARCH_OMAP2PLUS nor
CONFIG_AM33XX.  It however has so few uses that we can just modify the
code to check for both and drop the symbol. The symbols CONFIG_TI816X
and CONFIG_TI814X are for the repective SoCs.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-05 11:02:25 -04:00
Tom Rini
8627733941 ti816x: Rework DDR initialization sequence
The ti816x/am389x SoC is the first generation in what U-Boot calls the
"am33xx" family.  In the first generation of this family the DDR
initialization sequence is quite different from all of the subsequent
generations.  Whereas with ti814x (second generation) we can easily work
the minor differenced between that and am33xx (third generation), our
attempts to do this for ti816x weren't sufficient.  Rather than add a
large amount of #ifdef logic to make this different sequence work we add
a new file, ti816x_emif4.c to handle the various required undocumented
register writes and sequence and leverage what we can from
arch/arm/mach-omap2/am33xx/ddr.c still.  As DDR2 has similar problems
today but I am unable to test it, we drop the DDR2 defines from the code
rather than imply that it works by leaving it.  We also remove a bunch
of other untested code about changing the speed the DDR runs at.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-05 11:02:23 -04:00
Lokesh Vutla
fbd6295da4 arm: am33xx: Add support for mulitiple PLL input frequencies
am335x supports various sysclk frequencies which can be determined
using sysboot pins. PLLs should be configures based on this
sysclk frequency. Add PLL configurations for all supported
frequencies.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-12 08:37:14 -04:00
Lokesh Vutla
59041a5084 arm: am33xx: Fix MPU opp selection
Update MPU frequencies and voltages as per the latest
DM[1] dated: OCT 2011 Revised APRIL 2016, Section 5.4.
Below is the consolidated data:

MPU values for PG 2.0 and later(Package ZCZ and ZCE):

 -------------------------------------------------------
|	|	  ZCZ		|	  ZCE		|
|-------------------------------------------------------|
|	| VDD[V]   | ARM [MHz]	| VDD[V]   | ARM [MHz]  |
|-------|----------|------------|----------|------------|
| NITRO |  1.325   |   1000     |   NA     |    NA      |
|-------|----------|------------|----------|------------|
| TURBO |   1.26   |    800	|   NA     |    NA      |
|-------|----------|------------|----------|------------|
|OPP120 |   1.20   |    720     |   NA     |    NA      |
|-------|----------|------------|----------|------------|
|OPP100 |   1.10   |    600     |   1.10   |    600     |
|-------|----------|------------|----------|------------|
| OPP50 |   0.95   |    300     |   0.95   |    300     |
 -------------------------------------------------------

There is no eFuse blown on PG1.0 Silicons due to which there is
no way to detect the maximum frequencies supported. So default
to OPP100 for which both frequency and voltages are common on both
the packages.

[1] http://www.ti.com/lit/ds/symlink/am3356.pdf

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-12 08:37:12 -04:00
Lokesh Vutla
c187dd685a configs: convert CONFIG_SYS_MPUCLK to Kconfig
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-12 08:37:11 -04:00
Ladislav Michl
bf86392251 ARM: am33xx: define BOOT_DEVICE_ONENAND
am33xx does not support OneNAND, but we need this define anyway
to let UBI SPL code compile.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
2017-05-08 11:57:25 -04:00
Ladislav Michl
df9f07fa3d ARM: am33xx: fix typo in spl.h
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
2017-05-08 11:57:25 -04:00
Lukasz Majewski
d7ebbe9dc4 ti: wdt: common: Make the wdt IP defines common for the TI platform
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-08 21:32:48 -04:00
Ladislav Michl
50075153fe arm: OMAP2+: nandecc: propagate error to command return status
Currently nandecc returns zero even if underlaying
omap_nand_switch_ecc function fails. Fix that by
propagating error returned to command return value.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-03-11 22:30:25 -05:00
Marcin Niestroj
a73c8b32a7 ARM: am335x: Add support for chiliSOM
chiliSOM is a System On Module (http://http://grinn-global.com/chilisom/).
It can't exists on its own, but will be used as part of other boards.

Hardware specification:
 * TI AM335x processor
 * 128M, 256M or 512M DDR3 memory
 * up to 256M NAND

We place source inside arch/arm/mach-omap2/ directory and make it
possible to reuse initialization code (i.e. DDR, NAND init) for all
boards that use it.

Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-01-28 14:04:36 -05:00
Lokesh Vutla
140d76a9ee board: ti: amx3xx: Remove multiple EEPROM reads
Detect the board very early and avoid reading eeprom multiple times.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-11-21 13:59:25 -05:00
Lokesh Vutla
b64a7cb92d ARM: AMx3xx: Centralize early clock initialization
This is similar to Commit 93e6253d11 ("ARM: OMAP4/5: Centralize
early clock initialization") that was done for OMAP4+, reflecting the same
for AM33xx and AM43xx SoCs to centralize clock initialization.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add setup_early_clocks that calls setup_clocks_for_console for
        ti81xx]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-11-21 13:58:55 -05:00
Lokesh Vutla
1f95770807 ARM: AM437X: Add Silicon ID support
Add silicon ID code for AM437x silicon. This can be used to print
the cpu info using CONFIG_DISPLAY_CPUINFO.
Also printing "CPU :" along with cpu name in order to be consistent
with other OMAP platforms.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-10-08 09:33:36 -04:00
tomas.melin@vaisala.com
f61c9bcdfd ARM: Add register defines for am33xx ePWM registers
Register definitions needed for configuring the
ePWM module.

Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
2016-10-06 21:00:53 -04:00
Tom Rini
fa2f81b06f TI: Rework SRAM definitions and maximums
On all TI platforms the ROM defines a "downloaded image" area at or near
the start of SRAM which is followed by a reserved area.  As it is at
best bad form and at worst possibly harmful in corner cases to write in
this reserved area, we stop doing that by adding in the define
NON_SECURE_SRAM_IMG_END to say where the end of the downloaded image
area is and make SRAM_SCRATCH_SPACE_ADDR be one kilobyte before this.
At current we define the end of scratch space at 0x228 bytes past the
start of scratch space this this gives us a lot of room to grow.  As
these scratch uses are non-optional today, all targets are modified to
respect this boundary.

Tested on OMAP4 Pandaboard, OMAP3 Beagle xM

Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Paul Kocialkowski <contact@paulk.fr>
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Thomas Weber <weber@corscience.de>
Cc: Hannes Schmelzer <oe5hpm@oevsv.at>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Cc: Ben Whitten <ben.whitten@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: "B, Ravi" <ravibabu@ti.com>
Cc: "Matwey V. Kornilov" <matwey.kornilov@gmail.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Ash Charles <ashcharles@gmail.com>
Cc: "Kipisz, Steven" <s-kipisz2@ti.com>
Cc: Daniel Allred <d-allred@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
2016-09-06 13:41:42 -04:00
Ladislav Michl
0568dd0663 armv7: make gpmc_cfg const
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
[trini: Adapt am33xx, duovero, omap_zoom1]
Signed-off-by: Tom Rini <trini@konsulko.com>

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-07-22 14:46:00 -04:00
Heiko Schocher
694607b563 arm, am335x: Enable Spread Spectrum for the MPU
Enable Spread Spectrum for the MPU by calculating the required
values and setting the registers accordingly.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-06-09 13:53:07 -04:00
Heiko Schocher
c01bc75e7d am335x: add some missing CM_CLKMODE_DPLL_SSC macros
add missing CM_CLKMODE_DPLL_SSC_ACK_MASK,
CM_CLKMODE_DPLL_SSC_DOWNSPREAD_MASK and
CM_CLKMODE_DPLL_SSC_TYPE_MASK
defines. Used for enabling spread spectrum.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-06-09 13:53:07 -04:00
Heiko Schocher
9c410f7cb7 arm, am335x: add some missing GPIO register definitions
add missing:
OMAP_GPIO_IRQSTATUS_SET_0 and OMAP_GPIO_IRQSTATUS_SET_1
registers.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-06-09 13:53:06 -04:00
Lokesh Vutla
3164f3c689 ARM: AM33xx: Add support for Clock Synthesizer
The CDCE913 and CDCEL913 devices are modular PLL-based, low cost,
high performance , programmable clock synthesizers. They generate
upto 3 output clocks from a single input frequency. Each output can
be programmed for any clock-frequency.

Adding support for the same.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:52 -04:00
Lokesh Vutla
d8ff4fdb10 board: AM335x-ICEv2: Add DDR data
AM335x ICEv2 contains a 2Gbit(128Mx16) of DDR3 SDRAM(MT41J128M16JT-125),
capable of running at 400MHz. Adding this specific DDR configuration
details running at 400MHz.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:51 -04:00
Lokesh Vutla
bd716dd03d ARM: AM43xx: Fix BOOT_DEVICE_USB ID
commit 62c5674ea1 ("omap: SPL boot devices cleanup and completion")
cleans up the boot device ids for amx3xx soc. But mistakenly updates wrong
device IDs for AM43xx USB. Fixing the same here.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-18 17:11:44 -04:00
Vogt, Christof
7f961c90d7 am33xx changed BOOT_DEVICE_SPI to correct value
Changed BOOT_DEVICE Code for SPI on AM33xx.
According AM335x reference manual page 4960
(SPRUH73L-October 2011-Revised February 2015)
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-04-11 20:48:24 -04:00
Vignesh R
2d13459721 ARM: am43xx: Enable QUAD read and EDMA support for ti_qspi
Enable TI_EDMA3 and QUAD read support for ti_qspi on am43xx, this
increases read performance to 4 MB/s.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-11-17 23:43:29 +05:30
Heiko Schocher
92a3188d7d bitops: introduce BIT() definition
introduce BIT() definition, used in at91_udc gadget
driver.

Signed-off-by: Heiko Schocher <hs@denx.de>
[remove all other occurrences of BIT(x) definition]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
2015-09-11 17:15:32 -04:00
Kishon Vijay Abraham I
09cc14f4bc ARM: AM43xx: Add functions to enable and disable USB clocks
Added functions to enable and disable USB clocks which can be invoked
during USB init and USB exit respectively.

Cc: Roger Quadros <rogerq@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-08-28 12:33:21 -04:00
Kishon Vijay Abraham I
fca45722fb ARM: AM43xx: Add support for disabling clocks in uboot
Add do_disable_clocks() to disable clock domains and module clocks.
These clocks are enabled using do_enable_clocks().

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-08-17 23:29:14 +05:30
Nikita Kiryanov
4eaf126e06 gpio: am43xx: expand gpio support
AM43XX SoCs support up to 192 GPIO signals.
Make this amount available to the driver.

Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2015-08-12 20:48:04 -04:00