Add bootph-all prop to common pinctrl nodes for eMMC, FSPI, SD-card and
UART2 that are typically used by multiple boards. Unreferenced nodes are
removed from the SPL device tree during a normal build.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 SOQuartz compute module is mostly pin-compatible with the RPi
CM4 form factor. Therefore, it can slot into the official Raspberry Pi
CM4 IO carrier board. Add this configuration to U-Boot.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 SOQuartz Blade board is a carrier board for the SOQuartz
CM4-compatible compute module. It features PoE, an M.2 slot, an SD card
slot, HDMI, USB, serial and ethernet.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 SOQuartz Model A board is a carrier board for the SOQuartz
CM4-compatible compute module. It exposes PCIe, ethernet, USB, HDMI,
CSI, DSI, eDP and a 40 pin GPIO header, and is powered by 12V DC.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 Quartz64 Model B is a credit-card sized single-board
computer based on the Rockchip RK3566 SoC. The board features an M.2
PCIe slot, USB3, USB2, eMMC, SD, ethernet, HDMI, analog audio out, a
40 pin GPIO header and a DSI and CSI port, as well as on-board Wi-Fi.
Features tested on a Quartz64-B 4GB v1.4 2022-06-06:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 Quartz64 Model A is a single-board computer based on the
Rockchip RK3566 SoC. The board features USB3, SATA, PCIe, HDMI, USB2.0,
CSI, DSI, eDP, eMMC, SD, and an e-paper parallel port, as well as a
20 pin GPIO header.
Features tested on a Quartz64-A 8GB v2.0 2021-04-27:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Change RK3568 devices to use the newer dwc3-generic driver instead of
the old xhci-dwc3 driver for USB 3.0 support.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RK3568 share glue and ctrl in a single node. Use glue_get_ctrl_dev to
return the glue node as the ctrl node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Marek Vasut <marex@denx.de>
When dr_mode is peripheral or otg and U-Boot has not been built with
DM_USB_GADGET support, booting such device may end up with:
dwc3_glue_bind_common: subnode name: usb@fcc00000
Error binding driver 'dwc3-generic-wrapper': -6
Some drivers failed to bind
initcall sequence 00000000effbca08 failed at call 0000000000a217c8 (err=-6)
### ERROR ### Please RESET the board ###
Instead fail gracfully with ENODEV to allow board continue booting.
dwc3_glue_bind_common: subnode name: usb@fcc00000
dwc3_glue_bind_common: unsupported dr_mode 3
Also use CONFIG_IS_ENABLED(USB_HOST) and change switch to if statements
to improve readability of the code.
Fixes: 446e3a205b ("dwc3-generic: Handle the PHYs, the clocks and the reset lines")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marex@denx.de>
The current error check for device_find_first_child is not working as
expected, the documentation for device_find_first_child mention:
@devp: Returns first child device, or NULL if none
Return: 0
Change to return early when there is no child node to avoid any possible
null pointer dereference.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove regulator-boot-on prop from regulators now that the phy core has
support for phy-supply after the commit c57e0dcd93 ("phy: add support
for phy-supply").
This reverts commit 7911f409ff.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Commit ec107f04b6 ("rockchip: chromebook_minnie: Enable sound") and
commit 2d0c01b8f0 ("sound: rockchip: Add sound support for jerry")
enable audio support for chromebook_minnie and chromebook_jerry. Enable
it for chromebook_speedy as well, but put the non-upstream sound node
in the board -u-boot.dtsi instead.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sound support for chromebook_jerry needs the MAX98090 codec driver. This
was enabled in commit 2d0c01b8f0 ("sound: rockchip: Add sound support
for jerry"), but apparently lost in commit 7ae2729401 ("configs:
Resync with savedefconfig"). Enable it again.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook_jerry
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Commit 815ed79d83 ("video: rockchip: Use TrueType fonts with jerry")
enables makes chromebook_jerry use TrueType fonts. Make other veyron
boards switch to it as well.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Commit eba768c545 ("rockchip: jerry: Add serial support") enables
ROCKCHIP_SERIAL for chromebook_jerry to make the serial console work
correctly. Enable it also for other veyron boards.
Also enable logging and disable scrolling multiple lines at once as in
chromebook_jerry, and enable silent console as chromebook_minnie does.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The rk3288-veyron-speedy-u-boot.dtsi file duplicates the bootphase dts
fragments from rk3288-veyron-u-boot.dtsi even though it #inclues that.
Deduplicate these into the latter file, which should also make the eMMC
available to the other veyron boards' SPL.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Commit 9b312e26fc ("rockchip: Enable building a SPI ROM image on
jerry") produces a u-boot.rom file for chromebook_jerry, intended to be
written to SPI flash. Build this file for other veyron boards as well,
especially because they are already configured only to boot from SPI.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Commit 70e351bdfe ("rockchip: jerry: Enable RESET driver") enables
DM_RESET for chromebook_jerry to fix its display as required by changes
to the Rockchip video drivers. Enable it for other veyron boards as
well.
Fixes: cd529f7ad6 ("rockchip: video: edp: Add missing reset support")
Fixes: 9749d2ea29 ("rockchip: video: vop: Add reset support")
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook_jerry
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
DEBUG_UART_SKIP_INIT feature is implemented only by s5p (DEBUG_UART_S5P)
and pl01x (DEBUG_UART_PL010 or DEBUG_UART_PL011) serial drivers, but all
ARCH_ROCKCHIP configs rely on default DEBUG_UART_NS16550. The ns16550
serial driver does not depends on DEBUG_UART_SKIP_INIT, so drop it from
rockchip configs.
Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Boot devices defined in rk3308.c and in rk3308.dtsi do not match, causing
'same-as-spl' feature not to work. Update DTS definitions, aligning to
Linux kernel DTS and to other Rockchip DTS files, i.e. from dwmmc to mmc.
Add rk3308-rock-pi-s.dtb in dtb-y targets for CONFIG_ROCKCHIP_RK3308.
Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Some ROCK Pi S SKU/models are not equipped with SD-NAND (eMMC),
therefore SPL needs access to sdmmc: add it to rk3308-u-boot.dtsi
with bootph-all property.
Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Call to board_debug_uart_init() is useless, as mainline U-Boot can
not build TPL for rk3308, and proprietary ddr.bin to be used as TPL
is responsible to init debug uart. Moreover current implementation
of board_debug_uart_init() is not compatible with ROCK Pi S, as it
sets pins for UART2 channel 1 breaking access to sdmmc due to pinmux
conflict. Debug uart for ROCK Pi S is UART0.
Thus, avoid ROCKCHIP_RK3308 to select DEBUG_UART_BOARD_INIT and allow
to deselct it in rock-pi-s-rk3308_defconfig. The DEBUG_UART_BOARD_INIT
is already implied by ARCH_ROCKCHIP, therefore other boards based on
rk3308 chip are not affected by change.
Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Definition of function board_debug_uart_init() must be under
CONFIG_DEBUG_UART_BOARD_INIT and not under CONFIG_DEBUG_UART,
as it was: see debug_uart.h. In this way the debug uart can
be used but its board-specific initialization skipped by
configuration, if useless.
Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- Resync some of the K3 DTS files with the kernel, and pull in some
required related updates to keep drivers in sync with the dts files
now. Bring in some incremental fixes on top of one of the series I
applied recently as well as updating the iot2050 platform. Also do a
few small updates to the K2 platforms.
- Enable pcie support for rk3568;
- Add boards:
rk3399: Radxa ROCK 4SE;
rk3328: Orange Pi R1 Plus, Orange Pi R1 Plus LTS
rk3568: FriendlyARM NanoPi R5S/R5C, Hardkernel ODROID-M1
rk3588: Edgeble Neu6B
- support OP-TEE with binman;
- support Winbond SPI flash;
- rk3588 usbdp phy support;
- dts and config updates for different boards;
Move to using .env file for setting up environment variables for K2x_evm.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is more complex than it needs to be and makes converting these
boards over to plain text env files more difficult. Remove setting
mtdparts as the DTS already contain the partitions. While here also
drop the conflicting definitions from the K2 defconfigs.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The following checks are more reasonable as the previous logs were a bit
misleading as we could still get the logs that the authetication is
being skipped but still authenticate. Move the debug prints and checks
to proper locations.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Similar to get_fdt_mmc make get_overlays_mmc look at /boot/dtb/* path
for overlay files.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
All K3 SoCs use same set of args to load kernel for MMC. So move this to
common place to avoid duplication.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
This was regressed by the following commit and is required to build with
additional configs enabled.
Fixes: 14439cd71c ("configs: k3: make consistent bootcmd across all k3 socs")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Tested-by: Nikhil M Jain <n-jain1@ti.com>
Fix missing declaration of fdt_del_node_path() while compiling am625_fdt.c and
missing common_fdt.h include in common_fdt.c
Fixes: 70aa5a94d4 ("arm: mach-k3: am62: Fixup CPU core, gpu and pru nodes in fdt")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Only accept SPACE to stop autobooting. This is safer to avoid accidental
interruptions on unattended devices.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
ATF is now called BL31, and OP-TEE since 3.21 suggests to use
tee-raw.bin instead of (the still identical) tee-pager_v2.bin.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
This avoids having to maintain to defconfigs that are 99% equivalent.
The approach is to use binman to generate two flash images,
flash-pg1.bin and flash-pg2.bin. With the help of a template dtsi, we
can avoid duplicating the common binman image definitions.
Suggested-by: Andrew Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
The underlying issue was fixed in the meantime. Also signing the U-Boot
proper fit image now works. Just supporting custom cert templates
remains a todo.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
The common env bits now come via ti_armv7_common.env, include it.
Furthermore restore the board-specific boot targets and their ordering
that is now enforced k3-wide differently. Finally, enable
CONFIG_LEGACY_IMAGE_FORMAT explicitly which got lost while turning
FIT_SIGNATURE on by default for k3 devices.
Fixes: 53873974 ("include: armv7: Enable distroboot across all configs")
Fixes: 4ae1a247 ("env: Make common bootcmd across all k3 devices")
Fixes: 86fab110 ("Kconfig: Enable FIT_SIGNATURE if ARM64")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Update the am62 and am625 device-trees from linux v6.5-rc1. This needed
the following tweaks to the u-boot specific dtsi as well:
- Switch tick-timer to the main_timer as it's now defined in the main dtsi
- Secure proxies are defined in SoC dtsi
- Drop duplicate nodes - u-boot.dtsi is includes in r5-sk, no need for
either the definitions from main.dtsi OR duplication from u-boot.dtsi
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Maxime Ripard <mripard@kernel.org>
Cc: Francesco Dolcini <francesco@dolcini.it>
Cc: Sjoerd Simons <sjoerd@collabora.com>
Cc: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Timer0 is used by u-boot as the tick timer; Add it to the soc devices
list so it can be enabled via the k3 power controller.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Tested-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Cc: Francesco Dolcini <francesco@dolcini.it>
Cc: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
The TI AM654 timer is compatible with the omap-timer implementation,
so add it to the compatible id list.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Cc: Francesco Dolcini <francesco@dolcini.it>
Cc: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Hardkernel ODROID-M1 is a single board computer with a RK3568B2 SoC,
a slightly modified version of the RK3568 SoC.
Features tested on a ODROID-M1 8GB v1.0 2022-06-13:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe/AHCI
- SATA port
- USB host
Device tree is imported from linux v6.4.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Building U-Boot with CMD_INI=y result in following build warning:
cmd/ini.c: In function 'memgets':
include/linux/kernel.h:184:24: warning: comparison of distinct pointer types lacks a cast
184 | (void) (&_min1 == &_min2); \
| ^~
cmd/ini.c:92:15: note: in expansion of macro 'min'
92 | len = min((end - *mem) + newline, num);
| ^~~
Fix this by adding an int cast to the pointer arithmetic result.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The dwc_ahci driver use platform specific defines, place the platform
specific code behind a ifdef CONFIG_ARCH_OMAP2PLUS to allow build and
use of the driver on Rockchip platform.
Fixes: 02a4b42979 ("drivers: block: dwc_ahci: Implement a driver for Synopsys DWC sata device")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
The standard boot path expects the kernel_comp_addr_r and kernel_comp_size
variables for booting compressed kernel images. Define them using the previous
kernel_addr_c value (likely initially meant for this purpose) and usual size.
This was tested on the PX30 EVB to successfully boot compressed Linux kernel
images.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update config, IO and memory regions used based on [1] with pcie3x2
config reg address and reg size corrected.
Before this change:
PCI Autoconfig: Bus Memory region: [0-3eefffff],
PCI Autoconfig: Bus I/O region: [3ef00000-3effffff],
After this change:
PCI Autoconfig: Bus Memory region: [40000000-7fffffff],
PCI Autoconfig: Bus I/O region: [f0100000-f01fffff],
[1] https://lore.kernel.org/lkml/20221112114125.1637543-2-aholmes@omnom.net/
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add missing pinctrl and defconfig options to enable PCIe and NVMe
support on Radxa ROCK 3 Model A.
Use of pcie20m1_pins and pcie30x2m1_pins ensure IO mux selection M1.
The following pcie_reset_h and pcie3x2_reset_h ensure GPIO func is
restored to the perstn pin, a workaround to avoid having to define
a new rockchip,pins.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
