Motivation for this patch is to remove usage of function define
in cmd/mtdparts.c interface, based on env variables mtdids and mtdparts:
mtdparts_init() and find_dev_and_part().
See commit 938db6fe5d ("cmd: mtdparts: describe as legacy")
Now, all MTD devices are populated with their partition's information
found in DT, accessible in MTD devices. Use these information to find
the wanted partitions, no more need of find_dev_and_part() usage.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Describe the FMan Ethernet interfaces present on the board.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
For lockstep mode, cpu_release function is expecting to execute
on R5 core 0, if there is attempt to pass other than R5 core 0,
through an error saying "Lockstep mode should run on R5 core 0 only".
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230608032152.980-3-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Production version restarting platform version field from 0 that's why add
new calculation to be able to use different DT for these platforms.
Requested DT names for production silicons for IPP/SPP and EMU platform are
versal-net-ipp-rev2.0.dts and versal-net-emu-rev2.0.dts.
If platform version increase numbers revision can be even higher.
As of today platform version is 2 that's why expected is rev2.2.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/691e166b3cf2643d7edf482bda5500163eecb35a.1684311689.git.michal.simek@amd.com
Read boodmode register using versal_net_get_bootmode() in board_late_init
and prepare corresponding distro boot command sequence based on it.
versal_net_get_bootmode() will be changed to use smc calls later, but
for now directly reads the register.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230516144753.30869-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add compatible values to Ethernet PHY subnodes representing SMSC
LAN8710A PHYs on RZ/A1 and R-Mobile A1 boards. This allows software to
identify the PHY model at any time, regardless of the state of the PHY
reset line.
Ported from Linux kernel commit 1c65ef1c71e473c00f2a7a1b9c140f0b4862f282 .
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/247dc2074dae149af07b6d014985ad30eb362eda.1631174218.git.geert+renesas@glider.be
---
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Michal Simek <michal.simek@amd.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Add board code for the R8A77980 V3HSK board.
Add CPLD sysreset driver to the R-Car V3H SK board.
Extracted from a larger patch by Valentine Barshak.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync configs and board code with V3H Condor, squash CPLD driver in]
Import R8A77980 V3HSK DTs from Linux 6.1.31,
commit d2869ace6eeb ("Linux 6.1.31").
Extracted from a larger patch by Valentine Barshak.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Sync with 6.1.31
Add board code for the R8A77970 V3MSK board.
Add CPLD sysreset driver to the R-Car V3M SK board.
Extracted from a larger patch by Valentine Barshak.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync configs and board code with V3M Eagle, squash CPLD driver in]
Import R8A77970 V3MSK DTs from Linux 6.1.31,
commit d2869ace6eeb ("Linux 6.1.31").
Extracted from a larger patch by Valentine Barshak.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Sync with 6.1.31
Add support to identify R8A77995 r1.1 SoC.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
[Marek: Slight update to commit message, spell out the SoC model]
r8a7796 cpu revision v1.2 has the same information as revision v1.1.
This patch fixes revision display at startup to "rev 1.1/1.2".
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
[Marek: Slight update to commit message, spell out the SoC model]
The number of image array entries global variable is required
to support EFI capsule update. This information is exposed as a
num_image_type_guids variable, but this information
should be included in the efi_capsule_update_info structure.
This commit adds the num_images member in the
efi_capsule_update_info structure. All board files supporting
EFI capsule update are updated.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Sync the devicetree files from the official Linux kernel tree, v6.4-rc2.
This is covering both 64-bit and 32-bit Allwinner SoCs with Arm Ltd.
cores, we skip the new RISC-V bits for now, as sunxi RISC-V support
is still work in progress.
Among smaller cosmetic changes, this adds a SATA regulator node which we
need in U-Boot to get rid of hard-coded GPIOs.
Also this updates the Allwinner F1C100s DTs, enabling USB support, and
also adds the DTs for two new boards.
As before, this omits the non-backwards compatible changes to the R_INTC
controller, to remain compatible with older kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
In the first silicon revision of the am62x family of SoCs, the hardware
wakeup event cannot be used if software is unable to unlock the RTC
device within one second after boot. To work around this limitation
unlock RTC as soon as possible in the boot flow to maximize our chance
of linux being able to use this device.
Add the erratum i2327 workaround to initialize the RTC.
Signed-off-by: Nishanth Menon <nm@ti.com>
[bb@ti.com: rebased from 2021.01 and expanded commit and code messages]
Signed-off-by: Bryan Brattlof <bb@ti.com>
ATF and OPTEE regions may be firewalled from non-secure entities.
If we still map them for non-secure A53, speculative access may happen,
which will not cause any faults and related error response will be ignored,
but it's better to not to map those regions for non-secure A53 as there
will be no actual access at all.
Create separate table as ATF region is at different locations for am64
and am62/am62a.
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Add main_uart1 clocks in clk-data.c for J7200. Now,
main_uart1 clocks will be set up while booting the J7200 SoC.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Add device data for main_uart1 in dev-data.c for J7200. Now,
main_uart1 will be powered on while booting the J7200 SoC.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
When selecting UDA partition for booting. MMC read
mode was selected as RAW.
Due to growing/changing size of u-boot and tispl
images.
It will be better change to FS in case of UDA FS instead of
adjusting offsets with new change.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Add main_uart5 clocks in clk-data.c for J721S2. Now,
main_uart5 clocks will be set up while booting the J721S2 SoC.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Add device data for main_uart5 in dev-data.c for J721S2. Now,
main_uart5 will be powered on while booting the J721S2 SoC.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Add main_uart2 clocks in clk-data.c for J721E. Now,
main_uart2 clocks will be set up while booting the J721E SoC.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Add device data for main_uart2 in dev-data.c for J721E. Now,
main_uart2 will be powered on while booting the J721E SoC.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
K3 devices have some firewalls set up by ROM that we usually remove so
that the development is easy in HS devices.
While removing the firewalls disabling a background region before
disabling the foreground regions keeps the firewall in a state where all
the transactions will be blacklisted until all the regions are disabled.
This causes a race for some other entity trying to access that memory
region before all the firewalls are disabled and causes an exception.
Since there is no guarantee on where the background regions lie based on
ROM configurations or no guarantee if the background regions will allow
all transactions across the memory spaces, iterate the loop twice removing
the foregrounds first and then backgrounds.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
This reverts commit b8ebf24e7f.
This patch seems to be fundamentally wrong and requires a different way
on how the background firewalls should be configured so revert the patch
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
When build U-boot with clang with using commands:
$ make HOSTCC=clang xenguest_arm64_defconfig
$ make HOSTCC=clang CROSS_COMPILE=aarch64-linux-gnu- \
CC="clang -target aarch64-linux-gnueabi" -j8
The compiler reports error:
/tmp/start-acdf31.s:330:1: error: symbol '_start' is already defined
_start:
^
Because the symbol '_start' has been defined twice, one is defined in
arch/arm/cpu/armv8/start.S, another is defined in the header
boot0-linux-kernel-header.h.
To fix building failure, this patch removes the symbol '_start' from
boot0-linux-kernel-header.h.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
ARM requires a 4-byte alignment on all ARM code (though this
requirement is relaxed to 2-byte for some THUMB code) and we
should be explicit about that here.
GAS has its own fix for this[1] that forces proper alignment
on any section containing assembled instructions, but this is
not universal: Clang's and other gaslike assemblers lack this
implicit alignment. Whether or not this is considered a bug in
those assemblers, it is better to ask directly for what we want.
[1]: https://sourceware.org/bugzilla/show_bug.cgi?id=12931
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Arm duplicates the content of asm-generic/unaligned.h, so use that file
directly instead.
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
As part of various code clean-ups we have on occasion missed removing
unused header files. None of these files are referenced anywhere else
at this point.
Signed-off-by: Tom Rini <trini@konsulko.com>
It seems like the header inclusion guard for some Uniphier DDR PHY
header was misspelled.
Make the preprocessor symbol for the #ifndef and #define lines the
same, so that the double inclusion protection works as expected.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
It seems like the header inclusion guards for some IMX related headers
were misspelled or got out of sync.
Make the preprocessor symbols for the #ifndef and #define lines the
same, so that the double inclusion protection works as expected.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This platform is currently unmaintained and untested, so remove it.
Further, as it is the only TI816X SoC example, remove related files as
well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Apple's M2 Pro/Max SoC are somewhat similar to the M1 Pro/Max but
need a tweaked memory map. USB, NVMe, UART and WDT are working
with the existing drivers.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
K3 GP devices allows booting the secure binaries on them by bypassing
the x509 header on them.
ATF and OPTEE firewalling required the rproc_load to be called before
authentication. This change caused the failure for GP devices that
strips off the headers. The boot vector had been set before the headers
were stripped off causing the runtime stripping to fail and stripping
becoming in-effective.
Separate out the secure binary check on GP/HS devices so that the
boot_vector could be stripped before calling rproc_load. This allows
keeping the authentication later when the cluster is on along with
allowing the stripping of the binaries in case of gp devices.
Fixes: 1e00e9be62 ("arm: mach-k3: common: re-locate authentication for atf/optee")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
When booting with HS silicon, the system firmware image is 278270, which
is slightly larger than currently allocated amount.
This can cause unexpected behavior if this overlap interferes with other
things in memory, so increase this with a slightly margin added as well
to avoid any boot issues that can appear after system firmware gets
loaded.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
In non-combined boot flow for K3, all the firewalls are locked by default
until sysfw comes up. Rom configures some of the firewall for its usage
along with the SRAM for R5 but the PSRAM region is still locked.
The K3 MCU Scratchpad for j721e was set to a PSRAM region triggering the
firewall exception before sysfw came up. The exception started happening
after adding multi dtb support that accesses the scratchpad for reading
EEPROM contents.
The commit changes R5 MCU scratchpad for j721e to an SRAM region.
Old Map:
┌─────────────────────────────────────┐ 0x41c00000
│ SPL │
├─────────────────────────────────────┤ 0x41c40000 (approx)
│ STACK │
├─────────────────────────────────────┤ 0x41c85b20
│ Global data │
│ sizeof(struct global_data) = 0xd8 │
├─────────────────────────────────────┤ gd->malloc_base = 0x41c85bfc
│ HEAP │
│ CONFIG_SYS_MALLOC_F_LEN = 0x70000 │
├─────────────────────────────────────┤ CONFIG_SPL_BSS_START_ADDR
│ SPL BSS │ (0x41cf5bfc)
│ CONFIG_SPL_BSS_MAX_SIZE = 0xA000 │
└─────────────────────────────────────┘ CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX
(0x41cffbfc)
New Map:
┌─────────────────────────────────────┐ 0x41c00000
│ SPL │
├─────────────────────────────────────┤ 0x41c40000 (approx)
│ EMPTY │
├─────────────────────────────────────┤ 0x41c81920
│ STACK │
│ SPL_SIZE_LIMIT_PROVIDE_STACK=0x4000 │
├─────────────────────────────────────┤ 0x41c85920
│ Global data │
│ sizeof(struct global_data) = 0xd8 │
├─────────────────────────────────────┤ gd->malloc_base = 0x41c859f0
│ HEAP │
│ CONFIG_SYS_MALLOC_F_LEN = 0x70000 │
├─────────────────────────────────────┤ CONFIG_SPL_BSS_START_ADDR
│ SPL BSS │ (0x41cf59f0)
│ CONFIG_SPL_BSS_MAX_SIZE = 0xA000 │
├─────────────────────────────────────┤ 0x41cff9fc
│ NEW MCU SCRATCHPAD │
│ SYS_K3_MCU_SCRATCHPAD_SIZE = 0x200 │
└─────────────────────────────────────┘ CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX
(0x41cffbfc)
Fixes: ab977c8b91 ("configs: j721s2_evm_r5: Enable support for building multiple dtbs into FIT")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
[n-francis@ti.com: SRAM allocation addressing diagram]
Signed-off-by: Neha Francis <n-francis@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
When building for secure devices using non-buildman based image generation
the signed tispl.bin file is called tispl.bin_HS. Also build the unsigned
tispl.bin file as expected.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
To avoid using static setting for ECC enabled DDR size, switch
to calculate DDR size from DDRC setting
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update the DDR init flow for multi-setpoint support on i.MX93. A new
fsp_cfg struct need to be added in the timing file to store the diff
part of the DDRC and DRAM MR register for each setpoint.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add 625M bypass clock that may be used DRAM 625M
bypass mode support.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
According to DDRPHY errata, the Rank-to-Rank Spacing and tphy_rdcsgap
specification does not include the Critical Delay Difference (CDD) to
properly define the required rank-to-rank read command spacing after
executing PHY training firmware.
Following the errata workaround, at the end of data training, we get
all CDD values through the MessageBlock, then re-configure the DDRC
timing of WWT/WRT/RRT/RWT with comparing MAX CDD values.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Currently bootaux only supports to boot M33 core from TCM. Since ATF
has changed to use x2 parameter for M33 image address, update the
bootaux command to use input address, so we can support boot from
any possilbe address like TCM, DDR, Flexspi NOR.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
According to datasheet, iMX93 has fused parts with CORE1 or NPU or
both disabled. So update code to support it, the kernel device tree
runtime update will be added in future patches.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Config the A55 alt root clock to 500MHz(LD mode frequency)
by default. Normally, this clock root is only used as an
intermediate clock soure for A55 core/dsu when change the
ARM PLL frequency.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The HW_CTRL_SEL should be cleared when configuring PLL to avoid
potential glitch
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Support print reset cause. Since SRSR is not accessible from non-secure
world, so first save it to grp0, then read it in non-secure world.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The MAC addresses are hard coded for bring up. Change it to support
reading from fuse.
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
OPTEE memory region is set secure access only in ATF with configuration
to TRDC, and need to remove it from U-Boot, otherwise U-Boot and Kernel
may crash when accessing the memory
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move imx8 sci header file to include/firmware/imx, then we could
use build macro to reuse some i.MX8 drivers for i.MX9, such as
drivers/cpu/imx8_cpu.c.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Commit 1a7904fdfa ("mmc: fsl_esdhc_imx: Use esdhc_soc_data
flags to set host caps") exposed the following SD card error:
U-Boot 2023.04-00652-g487e42f7bc5e (Apr 05 2023 - 22:14:21 -0300)
CPU: Freescale i.MX7D rev1.0 1000 MHz (running at 792 MHz)
CPU: Commercial temperature grade (0C to 95C) at 35C
Reset cause: POR
Model: Freescale i.MX7 SabreSD Board
Board: i.MX7D SABRESD in non-secure mode
DRAM: 1 GiB
Core: 100 devices, 19 uclasses, devicetree: separate
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x10
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... Card did not respond to voltage
select! : -110
*** Warning - No block device, using default environment
The reason of the problem, as explained by Ye Li:
"When UHS is enabled in defconfig, the usdhc1 node in imx7d-sdb.dts does
not configure pad for VSELECT, also the data pad should be set to
100Mhz/200Mhz pin states."
Apply these changes into u-boot.dtsi for now. When these changes
reach the Linux mainline imx7d-sdb, they can be dropped from u-boot.dtsi.
This fixes UHS mode on the imx7d-sdb board.
Suggested-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Stop polluting the architecture directory with driver specific code,
move it into driver where it should be. Split the code slightly so
the MX8MM/MX8MN fuse readout and programming and MX8MP fuse readout
and programming are in their separate functions, and called in case
of matching SoC.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
It seems like the ROM log events for the iMX8M are not fully covered by
AN12853 i.MX ROMs Log Events, Rev. 0, May 2020. On iMX8M the ROM event
ID 0x82 seems to use parameter0 which stops the parsing because the end
of list is detected too early.
This patch adds ROM event ID 0x82 and skips the next word if ID 0x82 is
parsed.
Fixes: a5ee05cf71 ("ARM: imx: Pick correct eMMC boot partition from ROM log")
Signed-off-by: Fedor Ross <fedor.ross@ifm.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add sfc and flash node to device tree and config options to enable
support for booting from SPI NOR flash on Radxa ROCK 5 Model B.
Similar to RK3568 the BootRom in RK3588 can read all data and look for
idbloader at 0x8000, same as on SD and eMMC.
Use the rksd format and modify the mkimage offset to generate a bootable
u-boot-rockchip-spi.bin that can be written to 0x0 of SPI NOR flash. The
FIT image is loaded from 0x60000.
=> sf probe
SF: Detected mx25u12835f with page size 256 Bytes, erase size 4 KiB, total 16 MiB
=> load mmc 1:1 10000000 u-boot-rockchip-spi.bin
1492992 bytes read in 129 ms (11 MiB/s)
=> sf update $fileaddr 0 $filesize
device 0 offset 0x0, size 0x16c800
1300480 bytes written, 192512 bytes skipped in 11.103s, speed 137694 B/s
The BROM_BOOTSOURCE_ID value read back when booting from SPI flash does
not match the expected value of 3 (SPINOR) used by other SoCs. Instead a
value of 6 is read back, add a new enum value to handle this new
bootsource id.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Eugen Hristev <eugen.hristev@collabora.com>
Enable pinctrl for sdhci in SPL to support loading of FIT image from SD
and eMMC storage when booting from SPI NOR flash.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Like other Rockchip SoCs, DM_RESET and DM_REGULATOR_FIXED is useful
across RK3588 platform. Select them from arch Kconfig.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add sfc and flash node to device tree and config options to enable
support for booting from SPI NOR flash on Radxa ROCK 3 Model A.
Unlike prior generation SoCs the BootRom in RK3568 can read all data and
look for idbloader at 0x8000, same as on SD and eMMC.
Use the rksd format and modify the mkimage offset to generate a bootable
u-boot-rockchip-spi.bin that can be written to 0x0 of SPI NOR flash. The
FIT image is loaded from 0x60000.
=> sf probe
SF: Detected mx25u12835f with page size 256 Bytes, erase size 4 KiB, total 16 MiB
=> load mmc 1:1 10000000 u-boot-rockchip-spi.bin
1384448 bytes read in 119 ms (11.1 MiB/s)
=> sf update $fileaddr 0 $filesize
device 0 offset 0x0, size 0x152000
1179648 bytes written, 204800 bytes skipped in 9.901s, speed 143185 B/s
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable pinctrl for sdmmc and sdhci in SPL to support loading of FIT
image from SD and eMMC storage when booting from SPI NOR flash.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable pinctrl for sdmmc and sdhci in SPL to support loading of FIT
image from SD and eMMC storage when booting from SPI NOR flash.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3566-radxa-cm3-io with new defaults. Also add
missing supported mmc modes to sdhci node.
Remove the SPL_ROCKCHIP_BACK_TO_BROM=y option, SPL is expected to load
next stage from a FIT image and then jump to next stage not back to
BootRom.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM.
Extend SPL_MAX_SIZE to 0x40000, SPL is loaded to 0x0 and TF-A is loaded
to 0x40000, use the space in between as SPL_MAX_SIZE.
Add config option to include useful gpio cmd.
Remove the CONFIG_NET_RANDOM_ETHADDR=y option, ethaddr and eth1addr is
set based on cpuid read from OTP.
Filter out assigned-clock props with CONFIG_OF_SPL_REMOVE_PROPS,
U-Boot proper will read and configure assigned-clock props.
Add CONFIG_SYS_NS16550_MEM32=y to use 32bit access of serial register.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add bootph-all prop to xin24m clock node, it is referenced by cru node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the PCIe 2x1l 2 device and associated combphy.
On this bus, the Rock5B has an Ethernet transceiver connected.
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
[eugen.hristev@collabora.com: minor tweaks]
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
[jonas@kwiboo.se: add PCIe pins]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the node for PCIe 2x1l 2 device together with the corresponding
combphy.
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
[eugen.hristev@collabora.com: moved to -u-boot.dtsi, minor
adaptations]
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
[jonas@kwiboo.se: adapt to kernel node]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the use of SDMA mode to boost eMMC performance on ROCK Pi 4.
Also add missing flags to indicate the supported MMC modes.
Using mmc read command to read 32 MiB data shows following improvement:
=> time mmc read 10000000 2000 10000
Before: time: 3.178 seconds
After: time: 0.402 seconds
This also enables CONFIG_SPL_FIT_SIGNATURE option to help discover
any possible future issue with loading TF-A into DRAM/SRAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the use of SDMA mode to boost eMMC performance on RockPro64.
Also add missing flags to indicate the supported MMC modes.
Using mmc read command to read 32 MiB data shows following improvement:
=> time mmc read 10000000 2000 10000
Before: time: 3.178 seconds
After: time: 0.402 seconds
This also enables CONFIG_SPL_FIT_SIGNATURE option to help discover
any possible future issue with loading TF-A into DRAM/SRAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Loading part of TF-A into SRAM from eMMC using DMA fails on RK3399
similar to other Rockchip SoCs. Checksum validation fails with:
## Checking hash(es) for Image atf-2 ... sha256 error!
Bad hash value for 'hash' hash node in 'atf-2' image node
spl_load_simple_fit: can't load image loadables index 1 (ret = -1)
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Add a device tree property, u-boot,spl-fifo-mode, to control when the
rockchip_sdhci driver should disable the use of DMA and fallback on PIO
mode. Same device tree property is used by the rockchip_dw_mmc driver.
In commit 2cc6cde647 ("mmc: rockchip_sdhci: Limit number of blocks
read in a single command") the DMA mode was disabled using a CONFIG
option on RK3588. Revert that and instead disable DMA using the device
tree property for all RK3588 boards, also apply similar workaround for
all RK3399 boards.
Fixes: 2cc6cde647 ("mmc: rockchip_sdhci: Limit number of blocks read in a single command")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Quentin Schulz <foss+uboot@0leil.net> # RK3399 Puma, RK3588 Tiger
The current DT bindings for the rk3588 clock use a different ID than the
one that is supposed to be written to the hardware registers.
Thus, we cannot use directly the id provided in the phandle, but rather
use a lookup table to correctly setup the hardware.
This approach has been implemented already in Linux, by commit :
f1c506d152ff ("clk: rockchip: add clock controller for the RK3588")
Hence, implement a similar approach using the lookup table, and adapt
the existing reset driver to work with SoCs using lookup table.
The file rst-rk3588.c has been copied as much as possible from Linux.
Adapt the clk rk3588 driver as well to bind the reset driver with the
lookup table.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
To be able to initialize the pinctrl correctly at SPL level and read
u-boot proper from SD-Card, the pinctrl must be initialized.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add USB 2.0 host nodes and PHYs.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Co-developed-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
In current implementation, applications can execute only on R5 core 0.
The boot address for R5 core 1 is not supplied. Pass TCM address for
R5 core 1 based on the argument to fix the issue.
Remove incomplete comment.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/da865717d26648ab7a84345ca8749712efdddee5.1680699999.git.michal.simek@amd.com
The "zynqmp tcminit split" command should halt both cores and not just RPU1
when configuring the TCM memory for split mode.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Link: https://lore.kernel.org/r/20230323082506.31576-1-neal.frager@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for Schneider Electric RZ/N1D and RZ/N1S boards, which
are based on the Reneasas RZ/N1 SoC devices.
The intention is to support both boards using a single defconfig, and to
handle the differences at runtime.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The RZ/N1 is a family of SoC devices from Renesas, featuring:
* ARM Cortex-A7 CPU (single/dual core) and/or Cortex-M3
* Integrated SRAM up to 6MB
* Integrated gigabit ethernet switch
* Optional DDR2/3 controller
* I2C, SPI, UART, NAND, QSPI, SDIO, USB, CAN, RTC, LCD
Add basic support for this family, modeled on the existing RZA1.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This is taken directly from Linux kernel 6.3
(commit 457391b0380335d5e9a5babdec90ac53928b23b4)
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Commit 2564fce7ee ("sunxi: move Cortex SMPEN setting into start.S")
added SPL_ARMV7_SET_CORTEX_SMPEN to enable setting SMP bit. For
platforms not using SPL boot, add the corresponding non-SPL config,
so that CONFIG_IS_ENABLED(ARMV7_SET_CORTEX_SMPEN) works as expected.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
