Commit graph

753 commits

Author SHA1 Message Date
Jim Lin
8b3f7bf7ec tegra: usb: Fix device enumeration problem of USB1
A known hardware issue of USB1 port where bit 1 (connect status
change) of PORTSC register will be set after issuing Port Reset
(like "usb reset" in u-boot command line).
This will be treated as an error and stops later device enumeration.

Therefore we clear that bit after Port Reset in order to proceed
later device enumeration.

Signed-off-by: Jim Lin <jilin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-09 22:44:34 +02:00
Rajeshwari Shinde
c48ac11322 EXYNOS: Add power Enable/Disable for USB-EHCI
This patch adds functions to enable/disable the power of USB
host controller for EXYNOS5.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
2012-07-09 18:27:55 +02:00
Rajeshwari Shinde
71045da812 USB: EXYNOS: Set USB 2.0 HOST Link mode
This patch adds a function to set usb host mode to USB 2.0 HOST Link
for EXYNOS5

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
2012-07-09 18:27:55 +02:00
Rajeshwari Shinde
7590d3cece USB: EXYNOS: Incorporate EHCI review comments
This patch incorates the review comments given by Minkyu Kang for
EHCI support on EXYNOS

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
2012-07-09 18:27:54 +02:00
Andreas Bießmann
81f40345d1 ehci-atmel: fix compiler warning
Commit 7a101e946cba55e32d3d1265e30456c810046da3 introduced following warning:
---8<---
ehci-atmel.c: In function 'ehci_hcd_init':
ehci-atmel.c:49:2: warning: suggest parentheses around comparison in operand of '&' [-Wparentheses]
ehci-atmel.c: In function 'ehci_hcd_stop':
ehci-atmel.c:79:2: warning: suggest parentheses around comparison in operand of '&' [-Wparentheses]
--->8---

This patch fixes it.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
cc: Bo Shen <voice.shen@atmel.com>
cc: Marek Vasut <marex@denx.de>
2012-07-07 14:07:30 +02:00
Bo Shen
cc30b7803d Atmel : usb : add EHCI driver for Atmel SoC
Some Atmel SoC support USB EHCI, add the EHCI driver to support it.

To enable the USB EHCI, add the following configuration options into
board relative configuration file and remove USB OHCI options.

    #define CONFIG_USB_EHCI
    #define CONFIG_USB_EHCI_ATMEL
    #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS     2

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-07-07 14:07:29 +02:00
Wolfgang Denk
2ab5be7af0 Merge branch 'master' of git://git.denx.de/u-boot-usb
* 'master' of git://git.denx.de/u-boot-usb:
  USB: S5P: Add ehci support
  usb:udc:samsung Add functions for storing private gadget data in UDC driver
  usb:gadget:composite: Support for composite at gadget.h
  usb:gadget:composite USB composite gadget support
  usb:udc:samsung:cleanup Replace DEBUG_* macros with debug_cond() calls
  usb:udc: Remove duplicated USB definitions from include/linux/usb/ch9.h file
  USB: Document the QH and qTD antics in EHCI-HCD
  USB: Drop cache flush bloat in EHCI-HCD
  USB: Drop ehci_alloc/ehci_free in ehci-hcd
  USB: Align buffers at cacheline
  usb: use noinline define
2012-05-20 22:51:41 +02:00
Rajeshwari Shinde
5f0ffea455 USB: S5P: Add ehci support
This patch adds ehci driver support for s5p.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
2012-05-20 08:32:33 +02:00
Marek Vasut
41b1f0ac2e USB: Document the QH and qTD antics in EHCI-HCD
The construction of QH and qTD lists in ehci_submit_async() call is cryptic
business, add at least a bit of comments so if someone is reading it, he can at
least reference the intel ehci manual (ehci-r10.pdf).

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2012-05-20 08:32:32 +02:00
Marek Vasut
b8adb12095 USB: Drop cache flush bloat in EHCI-HCD
Discard the creepy cache flushing mechanisms in ehci-hcd.c and replace them with
more straightforward flushing. In the new approach, the flushing takes place
directly in ehci_submit_async() call instead of going through the QH list and
flushing all members and buffers. This discards a lot of weird bit operations
on the members of QH and qTD structures.

NOTE: Certainly, this flushes even qTDs which are possibly unused in some
transactions, though the overhead of the previous code was much higher than is
the overhead of flushing two more cache lines (which most probably aren't even
cached).

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2012-05-20 08:32:32 +02:00
Marek Vasut
de98e8b22a USB: Drop ehci_alloc/ehci_free in ehci-hcd
These two functions were called only from ehci_submit_async(), therefore
dissolve them as part of ehci_submit_async() to get rid of all those static
variables.

Signed-off-by: Marek Vasut <marex@denx.de>
2012-05-20 08:32:32 +02:00
Timo Ketola
5614553d56 imx: usb: There is no such register
The reference manual of i.MX25 (nor i.MX31) does not define such
register. This seems to access read only UH2_CAPLENGTH register (if
CONFIG_MXC_USB_PORT is zero).

Signed-off-by: Timo Ketola <timo@exertus.fi>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-05-15 08:31:34 +02:00
Timo Ketola
45b460dab3 i.MX25: usb: Set PORTSCx register
The USB controller in i.MX25 has a PORTSCx registers which should be
set. In this regard it is similar to the controller in i.MX31. As this
file is compiled only with i.MX25 and -31, #ifdef check can be removed.

Signed-off-by: Timo Ketola <timo@exertus.fi>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-05-15 08:31:34 +02:00
Wolfgang Grandegger
3f29d96218 USB: ehci-mx6: Fix broken IO access
To get USB working again on the i.MX6, this patch fixes a bug introduced
with commit 522b2a0 "Add proper IO accessors for mx6 usb registers.".
At that occasion, I also added the missing __iomem directive.

Cc: Marek Vasut <marex@denx.de>
CC: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
2012-05-15 08:31:33 +02:00
Jeroen Hofstee
90579fdd41 ehci-omap: fix for enabling the correct usb port
This is just a patch for the problem reported here:
http://lists.denx.de/pipermail/u-boot/2012-February/117580.html originally reported by Igor.

"Looks like this is copy paste error from my side,(for port2/3 it should have been bypass
 for port2/3 rather its port1 set in bypass mode)"

I only submit the patch since it is missing in 2012.04-rc3 while the twister board
depends on it. Maybe it is already somewhere in the reposistory, but I cannot find it.

note: the twister boards still needs an additional `usb reset`, don't know why.

U-Boot 2012.04-rc3-dirty (Apr 19 2012 - 21:38:38)

AM35XX-GP ES1.0, CPU-OPP2, L3-165MHz, Max CPU Clock 600 Mhz
TAM3517 TWISTER Board + LPDDR/NAND
I2C:   ready
DRAM:  256 MiB
NAND:  512 MiB
MMC:   OMAP SD/MMC: 0
In:    serial
Out:   serial
Err:   serial
Die ID #746c0000000000000155dc1405011024
Net:   DaVinci-EMAC, smc911x-0
Hit any key to stop autoboot:  0
twister => usb start
(Re)start USB...
USB:   Register 1313 NbrPorts 3
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
twister => usb reset
(Re)start USB...
USB:   Register 1313 NbrPorts 3
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
twister => usb reset
(Re)start USB...
USB:   Register 1313 NbrPorts 3
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
twister => usb reset
(Re)start USB...
USB:   Register 1313 NbrPorts 3
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found

Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Govindraj.R <govindraj.raja <at> ti.com>
Acked-by: Tom Rini <trini@ti.com>
2012-04-21 16:58:02 +02:00
Wolfgang Denk
f5cdc11775 Prepare v2012.04-rc2; minor Coding Style cleanup
Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-04-16 23:13:51 +02:00
Simon Glass
87f938c9f7 tegra: usb: Add support for Tegra USB peripheral
This adds basic support for the Tegra2 USB controller. Board files should
call board_usb_init() to set things up.

Configuration is performed through the FDT, with aliases used to set the
order of the ports, like this fragment:

        aliases {
		/* This defines the order of our USB ports */
                usb0 = "/usb@0xc5008000";
                usb1 = "/usb@0xc5000000";
        };

drivers/usb/host files ONLY: Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-03-29 08:12:48 +02:00
Simon Glass
9ab4ce223c usb: Add support for txfifo threshold
CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the txfilltuning
field in the EHCI controller on reset.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-03-29 08:12:48 +02:00
Fabio Estevam
522b2a02e6 USB: ehci-mx6: Add proper IO accessors
Add proper IO accessors for mx6 usb registers.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Jason Liu <r64343@freescale.com>
2012-03-27 09:41:16 +02:00
Robert Delien
b228e14e96 Renamed mx28_register to mx28_register_32 to prepare for mx28_register_8
This patch renames mx28_register to mx28_register_32 in order to
prepare for the introduction of an 8-bit register, mx28_register_8.

Signed-off-by: Robert Delien <robert@delien.nl>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
2012-03-26 23:09:24 +02:00
Wolfgang Grandegger
3f467529ca usb/ehci: Add USB support for the MX6Q
Currently, only USB Host 1 is supported.

Cc: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
2012-03-26 23:09:23 +02:00
Ajay Bhargav
54cb00486e USB: Armada100: EHCI Driver for Armada100 SOCs
This patch adds support for USB EHCI driver for Armada100 SOCs.

Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
2012-03-19 00:08:26 +01:00
Ajay Bhargav
732c7c2446 USB: Armada100: Add UTMI PHY interface driver
This patch adds USB host controller's UTMI PHY interface driver for
Armada100 SOCs.

Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
2012-03-19 00:08:26 +01:00
Mike Frysinger
5b84dd67cf usb: replace wait_ms() with mdelay()
Common code has a mdelay() func, so use that instead of the usb-specific
wait_ms() func.  This also fixes the build errors:

ohci-hcd.c: In function 'submit_common_msg':
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1519:9: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1816:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1827:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1844:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1563:11: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1583:9: sorry, unimplemented: called from here
make[1]: *** [ohci-hcd.o] Error 1

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Marek Vasut <marex@denx.de>
2012-03-19 00:08:16 +01:00
amartin@nvidia.com
f9636e8d38 USB: move keyboard polling into kbd driver
This moves keyboard polling logic from USB HCD drivers into USB
keyboard driver.  Remove usb_event_poll() as keyboard polling was
the only user of this API.  With this patch USB keyboard works with
EHCI controllers again.  Tested on a tegra2 seaboard.

Signed-off-by: Allen Martin <amartin@nvidia.com>
2012-03-03 16:56:29 +01:00
Govindraj.R
43b62393da ehci-omap: Clean up added ehci-omap.c
Clean up added ehci-omap.c and make it generic for re-use across
omap-soc having same ehci ip block. Also pass the modes to be configured
from board file and configure the ports accordingly. All usb layers
are not cache aligned, till then keep cache off for usb ops as ehci will use
internally dma for all usb ops.

* Add a generic common header ehci-omap.h having common ip block
  data and reg shifts.
* Rename and modify ehci-omap3 to ehci.h retain only conflicting
  sysc reg shifts remove others and move to common header file.
* pass the board data for beagle/panda accordinly to use
  ehci ports.

Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
2012-02-12 10:11:31 +01:00
Ilya Yanok
29321c0518 ehci-omap: driver for EHCI host on OMAP3
Taken from Beagle code. Tested on mcx board (AM3517-based).

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Tested-by: Stefano Babic <sbabic@denx.de>
2012-02-12 10:11:30 +01:00
Albert ARIBAUD
805ad7ee2d orion5x: add USB host ehci-marvell support
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2012-02-12 10:11:28 +01:00
Albert ARIBAUD
74d3442111 Remove kirkwood-specifics from marvell EHCI driver
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2012-02-12 10:11:27 +01:00
Albert ARIBAUD
a14bd41738 Rename ehci-kirkwood as ehci-marvell
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2012-02-12 10:11:27 +01:00
Wolfgang Denk
6b62b9a31d Coding Style cleanup
Fix trailing white space, indentation by spaces instead of TABs,
excessive blank lines, trailing blank lines.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-12-19 12:03:40 +01:00
Marek Vasut
3874b6d674 USB: EHCI: Allow EHCI post-powerup configuration in board files
This patch allows USB to work on some hosts, which need additional frobing after
the host was powered up via regular USB powerup sequence.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Wolfgang Grandegger <wg@denx.de>
Cc: Jason Liu <r64343@freescale.com>
2011-12-11 14:50:03 +01:00
Marek Vasut
1b80f2706e USB: MX5: Add MX5 usb post-init callback
This is useful for USB Transceivers init etc.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Wolfgang Grandegger <wg@denx.de>
Cc: Jason Liu <r64343@freescale.com>
2011-12-11 14:49:43 +01:00
Marek Vasut
0f8c86b549 USB: MX5: Abstract out mx51 USB pixmux configuration
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Wolfgang Grandegger <wg@denx.de>
Cc: Jason Liu <r64343@freescale.com>
2011-12-11 14:49:37 +01:00
Wolfgang Grandegger
1ca5620253 USB: MX5: add generic USB EHCI support for mx51 and mx53
It's derived from ehci-mxc and uses the header files of the
ehci-fsl interface. The callback board_ehci_hcd_init() has
been introduced to allow for board-specific setup when USB
is started.

Signed-off-by: Wolfgang Grandegger <wg@denx.de>
CC: Stefano Babic <sbabic@denx.de>
CC: Remy Bohmer <linux@bohmer.net>
2011-12-11 14:49:31 +01:00
Vincent Palatin
5f4b4f2fed ehci: speed up initialization
According to EHCI specification v1.0, the controller should stabilize
the power on a port at most 20 ms after the port power bit transition.
So, we put this setting in the virtual descriptor corresponding field,
(bPwrOn2PwrGood = 10 => 10 x 2ms = 20ms), this saves about 500ms at each
controller initialization/enumeration.

Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
2011-12-11 14:42:57 +01:00
Marek Vasut
7555d5ec29 USB: Add usb_event_poll() to get keyboards working with EHCI
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Remy Bohmer <linux@bohmer.net>
2011-12-11 14:40:38 +01:00
Marek Vasut
5f6aa03fda USB: Fix complaints about strict aliasing in OHCI-HCD
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2011-12-11 14:40:38 +01:00
Anatolij Gustschin
f55feafdee drivers/usb/host/ehci-mxc.c: Fix GCC 4.6 warning
Fix:
ehci-mxc.c: In function 'ehci_hcd_init':
ehci-mxc.c:113:6: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-12-09 10:34:53 +01:00
Wolfgang Denk
b0b20d4795 drivers/usb/host/sl811-hcd.c: Fix GCC 4.6 build warning
Fix:
sl811-hcd.c: In function 'sl811_rh_submit_urb':
sl811-hcd.c:556:8: warning: variable 'wIndex' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
2011-12-02 00:14:21 +01:00
Wolfgang Denk
0c2dd9a05b Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
  arm, davinci: add DAVINCI_MMC_CLKID
  arm, davinci_emac: fix driver bug if more then 3 PHYs are detected
  arm, davinci: da850/dm365 lowlevel cleanup
  omap5: Add omap5_evm board build support.
  omap4/5: Add support for booting with CH.
  omap5: emif: Add emif/ddr configurations required for omap5 evm
  omap5: clocks: Add clocks support for omap5 platform.
  omap5: Add minimal support for omap5430.
  omap: Checkpatch fixes
  omap4: make omap4 code common for future reuse
  GCC4.6: Squash warnings in onenand_base.c
  GCC4.6: Fix common/usb.c on xscale
  OneNAND: Add simple OneNAND SPL
  PXA: vpac270: Enable the new generic MMC driver
  PXA: Cleanup serial_pxa
  PXA: Drop csb226 and innokom boards (unmaintained)
  m28evk: Fix comment about the number of RAM banks
  mx31: Fix checkpatch warnings in generic.c
  mx31: Use proper IO accessor for GPR register
  mx31: Remove duplicate definition for GPR register
  qong: Use generic function for configuring GPR register
  M28EVK: Enable USB HOST support
  iMX28: Add USB HOST driver
  iMX28: Add USB and USB PHY register definitions
  M28: Add memory detection into SPL
  iMX28: Fix ARM vector handling
  M28: Add doc/README.m28 documentation
  M28: Add MMC SPL
  iMX28: Add support for DENX M28EVK board
  iMX28: Add u-boot.sb target to Makefile
  iMX28: Add image header generator tool
  iMX28: Add driver for internal RTC
  iMX28: Add GPMI NAND driver
  iMX28: Add APBH DMA driver
  iMX28: Add SPI driver
  iMX28: Add GPIO control
  iMX28: Add I2C bus driver
  iMX28: Add PINMUX control
  FEC: Add support for iMX28 quirks
  iMX28: Add SSP MMC driver
  iMX28: Initial support for iMX28 CPU
  MX25: zmx25: GCC4.6 fix build warnings
  da850: add new config file for AM18xx
  BeagleBoard: config: Switch to ttyO2
  OMAP3: Change omap3_evm maintainer
  devkit8000: Fix NAND SPL on boards with 256MB NAND
  integrator: enable Vpp and disable flash protection
  integrator: add system controller header
  integrator: make flash writeable on boot
  integrator: use io-accessors for board init
  integrator: move text offset to config
  integrator: pass configs for core modules
  ARM: remove superfluous setting of arch_number in board specific code.
  SPL: Allow ARM926EJS to avoid compiling in the CPU support code
  integrator: do not test first part of the memory
  arm: a320: fix broken timer
  ARM: define CONFIG_MACH_TYPE for all ronetix boards
  dm646x: pass board revision info to kernel
  dm646x: add new configuration for dm6467T
  arm, davinci: Fix setting of the SDRAM configuration register
  arm, davinci: Remove the duplication of LPSC functions
  arm, davinci: Rename AM1808 lowlevel functions to DA850
  da8xxevm: fix build error
  ARM: re-add MACH_TYPE_XXXXXX for VCMA9 board and add CONFIG_MACH_TYPE
2011-11-16 20:24:41 +01:00
Kumar Gala
dd22f7cf2c drivers/usb/host/ehci-fsl.c: Fix GCC 4.6 build warning
Fix:

ehci-fsl.c: In function 'ehci_hcd_init':
ehci-fsl.c:43:7: warning: variable 'usb_phy' set but not used [-Wunused-but-set-variable]

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-11 07:49:01 -06:00
Marek Vasut
dbb8f27901 iMX28: Add USB HOST driver
This driver supports both EHCI ports on the i.MX28 CPU.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
2011-11-11 11:36:58 +01:00
Wolfgang Grandegger
8d5d1516a2 ehci-mxc: remove incorrect comment
The USB port to be used is determined by CONFIG_MXC_USB_PORT.
So, it appears that the comment is not correct. Remove it.

Signed-off-by: Wolfgang Grandegger <wg@denx.de>
2011-11-04 22:06:37 +01:00
Lei Wen
a7efd719f4 ARM: kirkwood: reduce dependence of including platform file
For files like the drivers/serial/serial.c, it must include the
platform file, as the CONFIG_SYS_NS16550_COM1 must reference to the
definition in the platform definition files.

Include the platform definition file in the config file, so that it
would decouple the dependence for the driver files.

Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-10-27 21:56:33 +02:00
Anatolij Gustschin
c4c9fbebae consolidate mdelay by providing a common function for all users
There are several mdelay() definitions in the driver and
board code. Remove them all and provide a common mdelay()
in lib/time.c.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-10-22 01:16:08 +02:00
Wolfgang Denk
6bc52ef35c drivers/usb/host/ohci-hcd.c: fix warning: variable ... set but not used
Fix:
ohci-hcd.c: In function 'dl_transfer_length':
ohci-hcd.c:968:8: warning: variable 'tdINFO' set but not used [-Wunused-but-set-variable]

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Acked-by: Remy Bohmer <linux@bohmer.net>
2011-10-09 23:24:49 +02:00
Ramneek Mehresh
1b719e6654 powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014
Add UTMI and ULPI PHY support for USB controller on qoriq series of
processors with internal UTMI PHY implemented, for example P1010/P1014
 - Use both getenv() and hwconfig to get USB phy type till getenv()
   is depricated
 - Introduce CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY to specify if soc
   has internal UTMI phy

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:03 -05:00
Joel Fernandes
3ecfa9525c ehci-hcd: Allow cleanups to happen gracefully on a timeout.
With this, the EHCI seems to "recover" from a timeout. This is particularly
observable if you were to ping the wrong IP Address and then ping the correct
one or if there was a temporary failure during tftp sessions.

All it takes is one timeout to disable it. If you have a noisy network (lot
of traffic), even if the traffic is not for the board, the timeouts don't occur.

Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-04 11:36:22 +02:00
Jason Kridner
69716c1900 USB: Remove __attribute__ ((packed)) for struct ehci_hccr and ehci_hcor
Remove __attribute__ ((packed)) to prevent byte access to soc
registers in some gcc versions.

Having patches to enable ehci for the BeagleBoard lying around for
several months, this one was the show-stopper.

Switched to align(4), rather than remove the attribute, per suggestion
from Alexander.

Credits have to go to Laine Walker-Avina <lwalkera@ieee.org> for
finding the problem.

Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Cc: Alexander Holler <holler@ahsoftware.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-04 11:36:20 +02:00
Nobuhiro Iwamatsu
0b09f54a26 usb: r8a66597: Fix argument mistake of inl
Fail in build, because argument of inl used in r8a66597_read_fifo is wrong.

r8a66597.h:441:35: error: macro "inl" passed 2 arguments, but takes just 1
In file included from r8a66597-hcd.c:25:
r8a66597.h: In function ‘r8a66597_read_fifo’:
r8a66597.h:441: error: ‘inl’ undeclared (first use in this function)
r8a66597.h:441: error: (Each undeclared identifier is reported only once
r8a66597.h:441: error: for each function it appears in.)

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2011-08-08 21:40:40 +02:00
Matthias Weisser
dddb7c9ffd imx: Add support for USB EHCI on imx25
Adding support for USB host on imx25 using the internal PHY. Changing the name
of base address define for imx31 to get some unification.

Signed-off-by: Matthias Weisser <weisserm@arcor.de>
2011-07-14 15:41:24 +02:00
Zhao Chenhui
ae46d2a952 ehci-pci: Fix PCI EHCI driver for 36-bit
Convert the PCI base address into a virtual address.

Signed-off-by: Zhao Chenhui <b35336@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
2011-06-25 09:53:10 +02:00
Reinhard Meyer
86592f6059 AT91: change includes from asm/arch/io.h to asm/io.h
and remove the now unused asm/arch-at91/io.h

Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-05-18 07:56:51 +02:00
Reinhard Meyer
372f2783a7 AT91: fix related at91 driver files
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-05-18 07:56:51 +02:00
Stefano Babic
8627111543 IMX: MX31: Cleanup include files and drop nasty #ifdef in drivers
As exception among the i.MX processors, the i.MX31 has headers
without general names (mx31-regs.h, mx31.h instead of imx-regs.h and
clock.h). This requires several nasty #ifdef in the drivers to
include the correct header. The patch cleans up the driver and
renames the header files as for the other i.MX processors.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-04-27 19:38:05 +02:00
Wolfgang Denk
4db2fa7f94 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
Conflicts:
	drivers/usb/host/ehci-pci.c

Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-04-05 12:24:20 +02:00
Zhao Chenhui
298f8af17b echi: add ULI1575 PCI ID
Add ULI1575 EHCI controller to the list of the supported devices.

Signed-off-by: Zhao Chenhui <b35336@freescale.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:42 -05:00
Trübenbach, Ralf
0a5f7e1bdc ehci-pci: Add PCI EHCI controller
This patch adds support for the PI7C9X442SL PCIe EHCI host controller
from Pericom.

Tested at P4080DS eval board from Freescale.

Signed-off-by: Ralf Trübenbach <ralf.truebenbach@men.de>
Cc: Remy Bohmer <linux@bohmer.net>
2011-04-02 09:38:24 +02:00
Simon Glass
96820a3587 Fix EHCI usb submit timeout and unify with OHCI
Changed both to use a common timeout for URB submission, since they were using
different values and EHCI's was too short.

Also fixed EHCI to actually check if urb submission succeeded, rather than
silently continuing into the weeds.

Change-Id: I7f71499ffaa05187d8e5618db2419e1606007b82

Signed-off-by: Simon Glass <sjg@chromium.org>
2011-02-19 20:32:34 +01:00
Stefan Roese
a42a9d71b5 usb: Remove usb_dev_init() from ehci-ppc4xx.c
Calling usb_dev_init() from within the EHCI host driver is wrong.
The EHCI host driver should have no dependency/interconnection to the
USB device driver.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
2010-11-26 21:24:57 +01:00
Stefan Roese
273d72044c usb: Clear CMD_RUN while issuing CMD_RESET in ehci_reset()
This patch fixes a problem noticed on lwmon5 (PPC440EPx) using the
common EHCI driver, when "usb reset" is issued multiple times.
Upon the 2nd (and further) "usb reset" command, the command fails
with the following messages:

=> usb reset
(Re)start USB...
USB:   Register 1111 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 5 USB Device(s) found
       scanning bus for storage devices... 2 Storage Device(s) found
=> usb reset
(Re)start USB...
USB:   EHCI fail to reset
Error, couldn't init Lowlevel part

This patch fixes this problem. Now "usb reset" can be called multiple
times.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
2010-11-26 21:23:25 +01:00
Stefan Roese
67333f76b6 usb: Add WATCHDOG_RESET call to polling loop
This watchdog reset call is needed here, otherwise the lwmon5 board
(PPC440EPx based) will reset upon the "usb reset" command.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
2010-11-26 21:21:50 +01:00
Anatolij Gustschin
222d6dff27 usb: fix for USB_ST_STALLED status reporting in ehci_submit_async()
Checking the status field of the qTD token in the current code
do not take into acount cases where endpoint stall (halted) bit
is set together with XactErr status bit. As a result clearing
stall on an endpoint won't be done if this status bit was also
set. Check for halted bit and report USB_ST_STALLED status
if the host controller also indicates endpoit stall condition.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2010-11-26 21:21:16 +01:00
Sebastien Carlier
6d8962e814 Switch from archive libraries to partial linking
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils.  As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".

This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.

The name of each former library archive is preserved except for
extensions which change from ".a" to ".o".  This commit updates
references accordingly where needed, in particular in some linker
scripts.

This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols.  Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.

Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
2010-11-17 21:02:18 +01:00
Wolfgang Denk
09c83a45b7 ehci-hcd.c: fix hanging under higher load
This patch solves a problem with USB hanging under higher load on a
i.MX31 board.  It falls into class of typical USB problems and fixes:
if you don't understand the real cause, add a delay somewhere.

The problem appeared after introduction of ELF relocation, which
results in smaller code, which appears to run faster (probably because
it fits better in the cache); turning off the instruction cache,
adding debug printf()s and increasing the delay have all been found to
make the problem go away.

Moving the original "udelay(1)" up in the code to it's new place made
the problem appear much less frequently. Increasing the delay to 2
microseconds then made the code run reliably in all (hour-long) tests.
To be on the safe side, we set it to 5 microseconds here.

Signed-off-by: Heiko schocher <hs@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Stefano Babic <sbabic@denx.de>
2010-10-22 21:44:37 +02:00
Wolfgang Denk
8b675fe18e USB: fix Queue Element Transfer Descriptor changes
Commit 3ed1607 "USB: sync Queue Element Transfer Descriptor against
EHCI spec" added an "__attribute__ ((aligned (32)))" to the
declaration of struct qTD, as used for example in the Linux kernel as
well.

However, it turns out that this attribute causes errors in "usb start"
(like "ERROR: NOT USB_CONFIG_DESC 7b" and similar). Drop the attribute
again.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Dan Lykowski <lykowdk@gmail.com>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Stefano Babic <sbabic@denx.de>
2010-10-22 21:41:45 +02:00
Florian Fainelli
af68c06670 ehci-pci: print hccr, hcor and hc_lenght
It is useful to know the EHCI-PCI hccr, hcor and hc_lenght to make sure it was
successfully registered, and at the correct location.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2010-10-22 21:41:45 +02:00
Wolfgang Denk
3ed16071b0 USB: sync Queue Element Transfer Descriptor against EHCI spec
Appendix B "EHCI 64-Bit Data Structures" of the "Enhanced Host
Controller Interface Specification for Universal Serial Bus" (Rev.
1.0, March 12, 2002) defines additional fields which were missing in
U-Boot's struct qTD; as these are also present in recent versions of
struct ehci_qtd in the Linux kernel, we add them here, too.

This fixes some nasty memory corruption problems.

Reported-by: Dan Lykowski <lykowdk@gmail.com>
See http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/76942

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Dan Lykowski <lykowdk@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
2010-10-20 00:23:57 +02:00
Wolfgang Denk
083d506937 Merge branch 'master' of git://git.denx.de/u-boot-imx
Conflicts:
	board/logicpd/imx31_litekit/config.mk
	boards.cfg

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-19 20:58:16 +02:00
Damien Dusha
29c6fbe047 MPC5121: Add USB EHCI support
Signed-off-by: Francesco Rendine <francesco.rendine@valueteam.com>
Signed-off-by: Damien Dusha <d.dusha@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>

Coding style cleanup; slight file restructuring.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Remy Bohmer <linux@bohmer.net>
2010-10-18 22:33:32 +02:00
Stefano Babic
a2f9bff998 MX31: add delay between USB port setup and reset
Sometimes a usb tree is not popolated after a system reset.
It seems a delay is required after setting the USB ports
for the MX.31 before resetting the ehci controller.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-10-18 15:21:36 +02:00
Wolfgang Denk
6ca803750e Merge branch 'master' of git://git.denx.de/u-boot-imx 2010-10-17 19:57:38 +02:00
Stefano Babic
5b591502f9 MX31: Add support for MXC EHCI controller
The patch adds the EHCI controller for the i.MX31 Soc.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-10-13 18:11:44 +02:00
Marek Vasut
f2443d10ff USB: Make non-bulk delay longer in OHCI
This fixes TIMEOUT with my Kingston 32GB USB3.0 flashdrive, which I experienced
on my PXA270 (USB 1.1) Vpac270 board.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2010-10-13 12:07:58 +02:00
Becky Bruce
a5496a180b drivers/usb/host/ohci-hcd: rename readl/writel to ohci_readl/ohci_writel
This avoids a build warning that you see if anyone in the
header chain has included io.h (which is coming shortly).  The previous
code redefined readl/writel; this patch renames it to be specific to
ohci.  The defines are also moved from ohci-hcd.c to ohci.h.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
2010-06-30 21:38:10 +02:00
Sergey Matyukevich
64203c7b0f USB OHCI support for at91sam9g45 SoC
Add USB OHCI support for at91sam9g45ekes/at91sam9m10g45ek boards.

Note that according to errata from Atmel, OHCI is not operational
on the first revision of at91sam9g45 chip. So this patch enables
OHCI support for later revisions.

Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
2010-06-30 21:37:36 +02:00
Sergei Shtylyov
9fb3b50857 EHCI: zero out QH transfer overlay in ehci_submit_async()
ehci_submit_async() doesn't really zero out the QH transfer overlay (as the EHCI
specification suggests) which leads to the controller seeing the "token" field
as the previous call has left it, i.e.:
- if a timeout occured on the previous call (Active bit left as 1), controller
  incorrectly tries to complete a previous transaction on a newly programmed
  endpoint;
- if a halt occured on the previous call (Halted bit set to 1), controller just
  ignores the newly programmed TD(s) and the function then keeps returning error
  ad infinitum.

This turned out to be caused by the wrong orger of the arguments to the memset()
call in ehci_alloc(), so the allocated TDs weren't cleared either.

While at it, stop needlessly initializing the alternate next TD pointer in the
QH transfer overlay...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
2010-06-29 23:03:40 +02:00
Peter Tyser
1e3827d9cf mips: Move cpu/mips/* to arch/mips/cpu/*
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-04-13 09:13:25 +02:00
Sergei Shtylyov
d7a22a364c EHCI: add NEC PCI ID
Add NEC EHCI controller to the list of the supported devices.

Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>

 drivers/usb/host/ehci-pci.c |    1 +
 1 file changed, 1 insertion(+)
2010-04-08 21:40:00 +02:00
Sergei Shtylyov
c8b2d1dc0f EHCI: fix port reset reporting
Commit b416191a14 (Fix EHCI port reset.) didn't
move the code that checked for successful clearing of the port reset bit from
ehci_submit_root(), relying on wait_ms() call instead. The mentioned code also
erroneously reported port reset state when the reset was already completed.

Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
2010-04-08 21:39:59 +02:00
Sergei Shtylyov
e06a055bcd EHCI: fix off-by-one error in ehci_submit_root()
USB devices on the 2nd port are not detected and I get the following message:

The request port(1) is not configured

That's with default CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS value of 2. 'req->index'
is 1-based, so the comparison in ehci_submit_root() can't be correct.

Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
2010-04-08 21:39:59 +02:00
Sergei Shtylyov
6d313c84de EHCI: fix root hub device descriptor
On little endian machines, EHCI root hub's USB revision is reported as 0.2 --
cpu_to_le16() was missed in the initializer for the 'bcdUSB' descriptor field.
The same should be done for the 'bcdDevice' field.

Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
2010-04-08 21:39:58 +02:00
Matthias Fuchs
0701f730ce at91: use C structs for AT91 OHCI code
This patch is part of migrating the AT91 support towards
using C struct for all SOC access.

It removes one more CONFIG_AT91_LEGACY warning.

at91_pmc.h needs cleanup after migration of the drivers
has been done.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
2010-04-03 15:24:27 -05:00
Jens Scharsig
0cf0b93161 convert common files to new SoC access
* add's a warning to all files, which need update to new SoC access
 * convert common files in cpu/../at91 and a lot of drivers to use
   c stucture SoC access

Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
2010-02-12 12:31:55 -06:00
Chris Zhang
5f82887fee Add ppc440epx USB ehci support.
Currently ppc440epx uses OHCI for USB full-speed support. This change adds
support for EHCI.

Signed-off-by: Chris Zhang <chris@seamicro.com>
2010-01-09 10:27:15 +01:00
Chris Zhang
b416191a14 Fix EHCI port reset.
In USB ehci driver, the port reset is not terminated. EHCI spec says "A host
 controller must terminate the reset and stabilize the state of the port within
 2 milliseconds". Without termination, a port stays at reset state. This is
 observed on ppc4xx(sequoia) boards.

Signed-off-by: Chris Zhang <chris@seamicro.com>
2010-01-09 10:25:43 +01:00
Tom Rix
8f8bd565f3 USB Consolidate descriptor definitions
The header files usb.h and usbdescriptors.h have the same nameed
structure definitions for

usb_config_descriptor
usb_interface_descriptor
usb_endpoint_descriptor
usb_device_descriptor
usb_string_descriptor

These are out right duplicates in usb.h

usb_device_descriptor
usb_string_descriptor

This one has extra unused elements

usb_endpoint_descriptor

	unsigned char	bRefresh
	unsigned char	bSynchAddress;

These in usb.h have extra elements at the end of the usb 2.0
specified descriptor and are used.

usb_config_descriptor
usb_interface_descriptor

The change is to consolidate the definition of the descriptors
to usbdescriptors.h.  The dublicates in usb.h are removed.
The extra element structure will have their name shorted by
removing the '_descriptor' suffix.

So

usb_config_descriptor -> usb_config
usb_interface_descriptor -> usb_interface

For these, the common descriptor elements are accessed now
by an element 'desc'.

As an example

-	if (iface->bInterfaceClass != USB_CLASS_HUB)
+	if (iface->desc.bInterfaceClass != USB_CLASS_HUB)

This has been compile tested on MAKEALL arm, ppc and mips.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-12-20 12:47:37 +01:00
kevin.morfitt@fearnside-systems.co.uk
ac67804fbb Add a unified s3c24x0 header file
This patch adds a unified s3c24x0 cpu header file that selects the header
file for the specific s3c24x0 cpu from the SOC and CPU configs defined in
board config file. This removes the current chain of s3c24-type #ifdef's
from the s3c24x0 code.

Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2009-11-27 16:26:13 -06:00
Minkyu Kang
47e801bec3 s3c64xx: move s3c64xx header files to asm-arm/arch-s3c64xx
This patch moves the s3c64xx header files from include/
to include/asm-arm/arch-s3c64xx

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2009-11-27 16:26:13 -06:00
Prafulla Wadaskar
44259bb9e6 usb: bugfix driver/usb/host/ehci-hcd.c function ehci_submit_root
This change is cheked in Linux source and fix found to be in sync.
This patch is tested for USB host interface on Kirkwood based
Sheevaplug platform (ARM little endian board)

Risk: the impact of this patch is not validated on big endian board.
This need to be checked...

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
2009-07-23 23:27:06 +02:00
Wolfgang Denk
28958b8bea Coding Style cleanup; update CHANGELOG.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-07-23 22:23:23 +02:00
Kumar Gala
50243e3e7a usb: Fix compiler warning with gcc4.4
ehci-hcd.c: In function 'ehci_submit_root':
ehci-hcd.c:719: warning: value computed is not used
ehci-hcd.c:748: warning: value computed is not used

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
2009-07-11 11:30:17 +02:00
Prafulla Wadaskar
1d8937a469 usb: add Marvell Kirkwood ehci host controller driver
This driver is tested on Sheevaplug platform

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
2009-07-09 21:33:15 +02:00
Vivek Mahajan
0806615273 mpc8xxx: USB: fix: access of ehci struct elements
This patch fixes the access to the 'ehci' struct elements which should
have been taken care off in 4ef01010aa
Sorry about that.

Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
2009-07-09 21:33:15 +02:00
Vivek Mahajan
4ef01010aa mpc83xx: USB: Reorganized its support
The following patch reorganizes/reworks the USB support for mpc83xx
as under:-

  * Moves the 83xx USB clock init from drivers/usb/host/ehci-fsl.c to
    cpu/mpx83xx/cpu_init.c

  * Board specific usb_phy_type is read from the environment

  * Adds USB EHCI specific structure in include/usb/ehci-fsl.h

  * Copyrights revamped in most of the following files

Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
2009-06-12 20:47:17 +02:00
Vivek Mahajan
ed90d2c871 mpc8xxx: USB: Relocates ehci-fsl.h to include/usb
The following patch moves 8xxx-specifc USB #defines from
drivers/usb/host/ehci-fsl.h to include/usb.

Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
2009-06-12 20:47:17 +02:00
Vivek Mahajan
cfd39cdf94 mpc8xxx: USB: Removed reenablement of its interface
To prepare for the 85xx USB support, which requires interface enablement
only once in (specified) order, no different than instructions for
enabling the interface under 83xx.  It is unknown why the original author
enabled the interface twice (checked for references in errata, etc).

Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
2009-06-12 20:47:17 +02:00
RONETIX - Ilko Iliev
faa14babd7 at91: fix a USB problem for AT91SAM9261
This patch corrects the missing PLLB initialization in usb_cpu_init()
for AT91SAM9261.
Because of the missing PLLB initialization, the USB support for all
AT91SAM9261 based boards will work only if the PLLB is configured by a
precedent bootloader.

Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
2009-06-09 22:25:48 +02:00
Detlev Zundel
792a09eb9d Fix e-mail address of Gary Jennejohn.
Signed-off-by: Detlev Zundel <dzu@denx.de>
2009-05-15 22:11:59 +02:00
Peter Tyser
f9a109b3ad Replace __attribute references with __attribute__
__attribute__ follows gcc's documented syntax and is generally more
common than __attribute.  This change is only asthetic and should not
affect functionality.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-04-28 01:01:39 +02:00
Jean-Christophe PLAGNIOL-VILLARD
dc39ae9513 at91sam9/at91cap: improve clock framework
calculate dynamically the clock rate and pllb setting for usb

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-16 21:30:44 +02:00
Jean-Christophe PLAGNIOL-VILLARD
2731b9a866 drivers/usb: regorganisation
move to linux usb driver organisation

as following

drivers/usb/gadget
drivers/usb/host
drivers/usb/musb

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
2009-04-06 20:40:46 +02:00