Printing a buffer is a darn useful thing. Move the buffer print code
into print_buffer() in lib_generic/
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The 834x rev1.x silicon has one CPU5 errata.
The issue is when the data cache locked with
HID0[DLOCK], the dcbz instruction looks like no-op inst.
The right behavior of the data cache is when the data cache
Locked with HID0[DLOCK], the dcbz instruction allocates
new tags in cache.
The 834x rev3.0 and later and 8360 have not this bug inside.
So, when 834x rev3.0/8360 are working with ECC, the dcbz
instruction will corrupt the stack in cache, the processor will
checkstop reset.
However, the 834x rev1.x can work with ECC with these code,
because the sillicon has this cache bug. The dcbz will not
corrupt the stack in cache.
Really, it is the fault code running on fault sillicon.
This patch fix the incorrect dcbz operation. Instead of
CPU FP writing to initialise the ECC.
CHANGELOG:
* Fix the incorrect dcbz operation instead of CPU FP
writing to initialise the ECC memory. Otherwise, it
will corrupt the stack in cache, The processor will checkstop
reset.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Added code for reading and writing Mac addresses to/from ID EEPROM(0x57).
With attached patch, we can use command "mac/mac read/mac save/"
to read and write EEPROM under u-boot prompt.
U-boot will calculate the checksum of EEPROM while bootup,
if it is right, then u-boot will check whether the mac address
of eTSEC0/1/2/3 is availalbe (non-zero).
If there is mac address availabe in EEPROM, u-boot will use it,
otherewise, u-boot will use the mac address defined in
MPC8641HPCN.h. This matches the requirement to set unique mac address
for each TSEC port.
Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Second serial port on 440GX now defined as a system device.
Add 'Short Etch' code for Cicada PHY within 440gx_enet.c
Patch by Travis B. Sawyer, 12 Jul 2005
Check return value of malloc in 440gx_enet.c
Patch by Travis B. Sawyer, 18 Jul 2005
- remove all references to CONFIG_INIT_CRITICAL for ARM based boards
- introduce two new configuration options instead:
CONFIG_SKIP_LOWLEVEL_INIT and CONFIG_SKIP_RELOCATE_UBOOT
* Patch by Sascha Hauer, 28 Jun:
- add generic support for Motorola i.MX architecture
- add support for mx1ads, mx1fs2 and scb9328 boards
* Patches by Marc Leeman, 23 Jul 2004:
- Add define for the PCI/Memory Buffer Configuration Register
- corrected comments in cpu/mpc824x/cpu_init.c
* Add support for multiple serial interfaces
(for example to allow modem dial-in / dial-out)
Completion of the 8540ADS/8560ADS updates:
Fix some PCI and Rapid I/O memory maps,
Initialize both TSEC 1 and 2,
Initialize SDRAM
Update MAINTAINER for 85xx boards and README.mpc85xxads
- Make MPC5200 boards evaluate the SVR to print processor name and
version in checkcpu() (cpu/mpc5xxx/cpu.c).
* Patch by Kai-Uwe Bloem, 06 May 2004:
Fix endianess problem in cramfs code
- Add support for the Logic Zoom LH7A40x based SDK board(s),
specifically the LPD7A400.
* Patches by Robert Schwebel, 15 May 2004:
- call MAC address reading code also for SMSC91C111;
- make SMSC91C111 timeout configurable, remove duplicate code
- fix get_timer() for PXA
- update doc/README.JFFS2
- use "bootfile" env variable also for jffs2
- Rename DUET_ADS to MPC885ADS
- Rename CONFIG_DUET to CONFIG_MPC885_FAMILY
- Rename CONFIG_866_et_al to CONFIG_MPC866_FAMILY
- Clean up FADS family port to use the new defines
- add auto-complete support to the U-Boot CLI
- add support for NETTA and NETPHONE boards; fix NETVIA board
* Patch by Yuli Barcohen, 28 Mar 2004:
- Add support for MPC8272 family including MPC8247/8248/8271/8272
- Add support for MPC8272ADS evaluation board (another flavour of MPC8260ADS)
- Change configuration method for MPC8260ADS family
- Unify video mode handling for Chips & Technologies 69000 Video
chip and Silicon Motion SMI 712/710/810 Video chip
- Add selection of the video output (CRT or LCD) via 'videoout'
environment variable for the Silicon Motion
- README update
* Patch by Pierre Aubert, 18 Mar 2004:
include/common.h typo fix
* Patches by Tolunay Orkun, 17 Mar 2004:
- Add support for bd->bi_iic_fast[] initialization via environment
variable "i2cfast" (CONFIG_I2CFAST)
- Add "i2cfast" u-boot environment variable support for csb272
- Added LBA48 support (CONFIG_LBA48 & CFG_64BIT_LBA)
- Added support for 64bit printing in vsprintf (CFG_64BIT_VSPRINTF)
- Added support for 64bit strtoul (CFG_64BIT_STRTOUL)
* Patch by Masami Komiya, 27 Feb 2004:
Fix rarpboot: add autoload by NFS
* Patch by Dan Eisenhut, 26 Feb 2004:
fix flash_write return value in saveenv
* Patch by Stephan Linz, 11 Dec 2003
expand config.mk to avoid trigraph warnings on NIOS
* Rename "BMS2003" board into "HMI10"
Add support for IBM PPC440GX. Multiple EMAC Ethernet devices,
select MDI port based on enabled EMAC device.
Add support for XES Inc <http://www.xes-inc.com> XPedite1000 440GX
base PrPMC board.
see doc/README.MPC866 for details;
implement workaround for "SIU4" and "SIU9" silicon bugs on MPC866;
calculate CPU clock frequency from PLL register values.
* Add support for 128 MB RAM on TQM8xxL/M modules
