Provide command 'mmc wp' to power on write protect boot areas on eMMC
devices.
The B_PWR_WP_EN bit in the extended CSD register BOOT_WP is set. The boot
area are write protected until the next power cycle occurs.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Boot partitions of eMMC devices can be power on or permanently write
protected. Let the 'mmc info' command display the protection state.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When a mismatch is found trying to write an image for one boot method
to a different boot device, print an error message including the image
header marked target boot device type.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Ensure that the device to which an image is being written includes
header information indicating boot support for the destination
device.
This is derived from the support in the SolidRun master-a38x vendor
fork.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Add support for Armada 38x devices in bubt flashing utility.
This is based on (and streamlined from) the support in the SolidRun
master-a38x vendor fork.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
The eeprom_i2c_bus is not used outside of this file, make it static.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This commit adds the command ubi rename to rename an ubi volume.
The format of the command is: ubi rename <oldname> <newname>.
To enable this command, the option CMD_UBI_RENAME must be selected.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix documentation bug reported by 'make refcheckdocs'.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Add compressed Image parsing support so that booti can parse both
flat and compressed Image to boot Linux. Currently, it is difficult
to calculate a safe address for every board where the compressed
image can be decompressed. It is also not possible to figure out the
size of the compressed file as well. Thus, user need to set two
additional environment variables kernel_comp_addr_r and filesize to
make this work.
Following compression methods are supported for now.
lzma, lzo, bzip2, gzip.
lz4 support is not added as ARM64 kernel generates a lz4 compressed
image with legacy header which U-Boot doesn't know how to parse and
decompress.
Tested on HiFive Unleashed and Qemu for RISC-V.
Tested on Qemu for ARM64.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Fix minor rST formatting problems]
Signed-off-by: Tom Rini <trini@konsulko.com>
This additional bitflip memory test is inspired by the bitflip test
in memtester v4.3.0. It show some errors on some problematic GARDENA
MT7688 based boards. The other memory tests usually don't show any
errors here.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch changes mtest to correctly count the overall errors and
print them even in the abort (Ctrl-C) case.
Signed-off-by: Stefan Roese <sr@denx.de>
This command is a new command called "unlz4" that decompresses from memory
into memory.
Used with the CONFIG_CMD_UNLZ4 optionenabled.
Signed-off-by: Yusuke Ashiduka <ashiduka@fujitsu.com>
[trini: Use %zd / %zX not %ld / %lX in printf]
Signed-off-by: Tom Rini <trini@konsulko.com>
This pull request
* provides an implementation of UEFI secure booting
* fixes a problem with the rsa_mod_exp driver which stops some boards
from booting when CONFIG_RSA is enabled which is needed for UEFI
secure booting
* enables the EFI_RNG_PROTOCOL if DM_RNG is enabled
* fixes some function comments
-----BEGIN PGP SIGNATURE-----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=+ZDZ
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-07-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-07-rc1
This pull request
* provides an implementation of UEFI secure booting
* fixes a problem with the rsa_mod_exp driver which stops some boards
from booting when CONFIG_RSA is enabled which is needed for UEFI
secure booting
* enables the EFI_RNG_PROTOCOL if DM_RNG is enabled
* fixes some function comments
'fdt systemsetup' wasn't working, due to the fact that the 'set' command
was being parsed in do_fdt() by only testing for the leading 's' instead
of "se", which kept the "sys" test further down from executing. Changed
to test for "se" instead, now 'fdt systemsetup' works (to test the
ft_system_setup proc w/o having to boot a kernel).
Signed-off-by: Tom Warren <twarren@nvidia.com>
This sub-command will be used to test image authentication,
in particular, a case where efi_load_image() failed with
EFI_SECURITY_VIOLATION but we still want to try efi_start_image().
We won't run such a case under normal bootmgr because it simply
refuses to call efi_start_image() if anything but EFI_SUCCESS
is returned when loading an image.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
With "-at" option, EFI_VARIABLE_TIME_BASED_AUTHENTICATED_WRITE_ACCESS
will be passed to SetVariable() to authenticate the variable.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
A signature database variable is associated with a specific guid.
For convenience, if user doesn't supply any guid info, "env set|print -e"
should complement it.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Pull in changes that have been pending in our 'next' branch. This
includes:
- A large number of CI improvements including moving to gcc-9.2 for all
platforms.
- amlogic, xilinx, stm32, TI SoC updates
- USB and i2c subsystem updtaes
- Re-sync Kbuild/etc logic with v4.19 of the Linux kernel.
- RSA key handling improvements
Add a test for the dm drivers command. Also fix a null pointer dereference
revealed by said test.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sub-nodes of /reserved-memory may be disabled. In this case we should not
reserve memory in the memory map.
Reported-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Fixes: fef907b2e4 ("efi_loader: create reservations after
ft_board_setup")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
On 32 bit systems fix
warning: cast to pointer from integer of different size
[-Wint-to-pointer-cast]
Fixes: a415d61eac ("cmd: map addresses to sysmem in efidebug memmap")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
K3 J721E:
* OSPI boot support
* Support for loading remote cores in R5 SPL
* PMIC ESM Support
* Minor fixes for R5F and C7x remoteproc drivers
K3 AM654:
* Update AVS class 0 voltages.
* Add I2C nodes
DRA7xx/AM57xx:
* Fixed Android boot on AM57xx
AM33/AM43/Davinci:
* switch to driver model for the net and mdio driver for baltos
* Add DM/DTS support for omap video driver
* Enable fastboot on am335x-evm
Currently, bootefi only parses memory reservation block to setup
EFI reserved memory mappings. However, it doesn't parse the
reserved-memory[1] device tree node that also can contain the
reserved memory regions.
Add capability to parse reserved-memory node and update the EFI memory
mappings accordingly.
1. <U-Boot source>/doc/device-tree-bindings/reserved-memory/reserved-memory.txt]
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Fix an endless loop.
The /reserved-memory node may have children without reg property. Remove
a superfluous debug statement.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Addresses in the sandbox's device tree are in the sandbox's virtual address
space. If we want to compare memory reservations in the device-tree with
the output of 'efidebug memmap', we need to convert back to this address
space.
Adjust the output of the 'efidebug memmap' command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Some memory reservations are made in ft_board_setup(). Ensure that we
create reserved memory map entries after ft_board_setup().
The downside of this patch is that if bootefi is called multiple times with
an devicetree argument superfluous reservations for the old copies of the
device tree will exist. But that is still better than missing a reservation.
Deleting the superfluous reservations is not possible because reservations
in the memory map are rounded to page size and may be coallesced.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
4dbc107f46 ("cmd: gpio: Correct do_gpio() return value") correctly
changed the behaviour of the gpio command to return CMD_RET_SUCCESS or
CMD_RET_FAILURE, but any existing script which expects the return value
to be the pin value is broken by this change.
Reinstate the legacy behaviour for `gpio input` only.
Fixes: 4dbc107f46 ("cmd: gpio: Correct do_gpio() return value")
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Signed-off-by: Alex Kiernan <alex.kiernan@hivehome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the missing line feed at the error message if the variable referred to
by 'efidebug boot rm' does not exist.
Shorten the format string by using the variable name instead of the number
of the boot variable.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
There is a wrong usage of utf8_utf16_strncpy() in "boot rm" command, and
then it will end up with a failure of this command due to a wrong
value of an interim variable ("var_name16").
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Move the generic elf loading/validating functions to lib/
so that they can be re-used and accessed by code existing
outside cmd.
While at it remove the duplicate static version of load_elf_image_phdr
under arch/arm/mach-imx/imx_bootaux.c.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Suggested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Following kernel's proposal for an arch-agnostic initrd loading
mechanism [1] let's implement the U-boot counterpart.
This new approach has a number of advantages compared to what we did up
to now. The file is loaded into memory only when requested limiting the
area of TOCTOU attacks. Users will be allowed to place the initramfs
file on any u-boot accessible partition instead of just the ESP one.
Finally this is an attempt of a generic interface across architectures
in the linux kernel so it makes sense to support that.
The file location is intentionally only supported as a config option
argument(CONFIG_EFI_INITRD_FILESPEC), in an effort to enhance security.
Although U-boot is not responsible for verifying the integrity of the
initramfs, we can enhance the offered security by only accepting a
built-in option, which will be naturally verified by UEFI Secure Boot.
This can easily change in the future if needed and configure that via ENV
or UEFI variable.
[1] https://lore.kernel.org/linux-efi/20200207202637.GA3464906@rani.riverdale.lan/T/#m4a25eb33112fab7a22faa0fd65d4d663209af32f
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
UEFI spec 2.8 errata A replaces the RuntimeServicesSupported variable
defined in UEFI spec 2.8 by the configuration table
EFI_RT_PROPERTIES_TABLE. So let's follow suit.
Cc: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Ard Biesheuvel <ardb@kernel.org>
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl48iogACgkQfxc6PpAI
reaVzAf/an3/yKe6r3CVWlcRV6H/dVg1ApnnLpX7jS0p0b++oCVvOiy7z1WPXj3k
b1SSgENDeeZ/8EHio+Gf7ZidH/TGEj7L6YEFwd1t60GMkZiWEkNf4Z53tw482YG+
96hoPD+ySTW+ddIdVHWAFG2I4aEiKHANJAp/ItNdD+rLbrEwNQy+eiK5JTOk80B6
/X8AJCLZeAC1s7vs+2+WolgjT78QGzA9HHalMiublcqh0ivKKk0QeQiOKKPe8JYJ
om5YY1TxayQ60Xmo5f39/SBfzEEklxw83sU9o1tBeYzyVUpu7fQdkxiDbWdsij77
DgwLdeYQJGbN+hdSWE0gjTqyhW+lWA==
=KRoA
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-6feb20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
sandbox conversion to SDL2
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
Both CMD_MX_CYCLIC and MX_CYCLIC are in use and defined in Kconfig,
but only the non-CMD version currently does anything. This changes all
usages to prefer the CMD_MX_CYCLIC option (since it's only affecting
addition of the commands), and switches defconfigs using the non-CMD
version to use the CMD version.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
Based on reading the text of the license comment this appears to be
the BSD-2-Clause license but with an imperfect word match as
BSD-2-Clause was not (as far as I recall) a common license choice at the
time the code was written.
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Use the correct return value in function do_gpio() and update
commands documentation with the return values from command_ret_t enum.
CMD_RET_SUCCESS is returned on command success and CMD_RET_FAILURE is
returned on command failure.
The command was returning the pin value, which caused confusion when
debugging (#define DEBUG).
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Tested-by: Robert Marko <robert.marko@sartura.hr>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This adds a subcommand to dm to dump out what drivers are installed, and their
compatible strings. I have found this useful in ensuring that I have the correct
drivers compiled, and that I have put in the correct compatible strings.
Signed-off-by Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The command tpm (and tpm2) search the tpm and use it.
On sandbox, there are two tpm (tpm 1.x and tpm 2.0).
So the command tpm and tpm2 are always executed with
the first tpm (tpm 1.x), and the command tpm2 always
fails.
This add a subcommand device to command tpm and
command tpm2. Then the command tpm and tpm2 use
the device selected with the subcommand device.
To be compatible with previous behaviour, if the
subcommand device is not used before a tpm (or tpm2)
command, the device 0 is selected.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Convert Android documentation from regular txt format to Sphinx (RST).
Also add Android index.rst file and reference it in root index.rst, so
that Android documentation is visible.
Test:
$ make htmldocs
$ xdg-open doc/output/index.html
Signed-off-by: Sam Protsenko <joe.skb7@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Describe Android Boot Image format, how its support is implemented in
U-Boot and associated commands usage.
Signed-off-by: Sam Protsenko <joe.skb7@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This command can be used to extract fields and image payloads from
Android Boot Image. It can be used for example to implement boot flow
where dtb is taken from boot.img (as v2 incorporated dtb inside of
boot.img). Using this command, one can obtain needed dtb blob from
boot.img in scripting manner, and then apply needed dtbo's (from "dtbo"
partition) on top of that, providing then the resulting image to bootm
command in order to boot the Android.
Also right now this command has the sub-command to get an address and
size of recovery dtbo from recovery image (for non-A/B devices only,
see [1,2] for details).
It can be tested like this:
=> mmc dev 1
=> part start mmc 1 boot_a boot_start
=> part size mmc 1 boot_a boot_size
=> mmc read $loadaddr $boot_start $boot_size
=> abootimg get ver
=> abootimg dump dtb
[1] https://source.android.com/devices/bootloader/boot-image-header
[2] https://source.android.com/devices/architecture/dto/partitions
Signed-off-by: Sam Protsenko <joe.skb7@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
New analysis by the tool has shown that we have some cases where we
weren't handling the error exit condition correctly. When we ran into
the ENOMEM case we wouldn't exit the function and thus incorrect things
could happen. Rework the unwinding such that we don't need a helper
function now and free what we may have allocated.
Fixes: 18030d04d2 ("GPT: fix memory leaks identified by Coverity")
Reported-by: Coverity (CID: 275475, 275476)
Cc: Alison Chaiken <alison@she-devel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Jordy <jordy@simplyhacker.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Some PMICs (such as the DA9063) have non-contiguous register maps.
Attempting to read the non implemented registers returns an error
rather than a dummy value which causes 'pmic dump' to terminate
prematurely.
Fix this by allowing the PMIC driver to return -ENODATA for such
registers, which will then be displayed as '--' by pmic dump.
Use a single error code rather than any error code so that
we can distinguish between a hardware failure reading the PMIC
and a non implemented register known to the driver.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
If we didn't unbind the sata from block device, the same devices would
be added after sata remove,
This patch is to resolve this issue as below:
=> sata info
SATA#0:
(3.0 Gbps)
SATA#1:
(3.0 Gbps)
Device 0: Model: INTEL SSDSA2BW300G3D Firm: 4PC10362 Ser#: BTPR247005PY30
Type: Hard Disk
Supports 48-bit addressing
Capacity: 286168.1 MB = 279.4 GB (586072368 x 512)
Device 1: Model: INTEL SSDSA2BW300G3D Firm: 4PC10362 Ser#: BTPR247005VX30
Type: Hard Disk
Supports 48-bit addressing
Capacity: 286168.1 MB = 279.4 GB (586072368 x 512)
=> sata stop
=> sata info
SATA#0:
(3.0 Gbps)
SATA#1:
(3.0 Gbps)
Device 0: Model: INTEL SSDSA2BW300G3D Firm: 4PC10362 Ser#: BTPR247005PY300
Type: Hard Disk
Supports 48-bit addressing
Capacity: 286168.1 MB = 279.4 GB (586072368 x 512)
Device 1: Model: INTEL SSDSA2BW300G3D Firm: 4PC10362 Ser#: BTPR247005VX300
Type: Hard Disk
Supports 48-bit addressing
Capacity: 286168.1 MB = 279.4 GB (586072368 x 512)
Device 2: Model: INTEL SSDSA2BW300G3D Firm: 4PC10362 Ser#: BTPR247005PY300
Type: Hard Disk
Supports 48-bit addressing
Capacity: 286168.1 MB = 279.4 GB (586072368 x 512)
Device 3: Model: INTEL SSDSA2BW300G3D Firm: 4PC10362 Ser#: BTPR247005VX300
Type: Hard Disk
Supports 48-bit addressing
Capacity: 286168.1 MB = 279.4 GB (586072368 x 512)
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The 'sspi' command hard-coded 1 MHz bus frequency for all transmissions.
Allow changing that at runtime by specifying '@freq' bus frequency in Hz.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This patch modify the loop in mtd erase command to erase one by one
the blocks in the requested area.
It solves issue on "mtd erase" command on nand with existing bad block,
the command is interrupted on the first bad block with the trace:
"Skipping bad block at 0xffffffffffffffff"
In MTD driver (nand/raw), when a bad block is present on the MTD
device, the erase_op.fail_addr is not updated and we have the initial
value MTD_FAIL_ADDR_UNKNOWN = (ULL)-1.
This case seems normal in nand_base.c:nand_erase_nand(),
we have the 2 exit cases during the loop:
1/ we have a bad block (nand_block_checkbad)
instr->state = MTD_ERASE_FAILED
loop interrupted (goto erase_exit)
2/ if block erase failed (status & NAND_STATUS_FAIL)
instr->state = MTD_ERASE_FAILED;
instr->fail_addr =
((loff_t)page << chip->page_shift);
loop interrupted (goto erase_exit)
So erase_op.fail_addr can't be used if bad blocks were present
in the erased area; we need to use mtd_erase only one block to detect
and skip these existing bad blocks (as it is done in nand_util.c).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Execute the command cls (for clear screen), when the "menu background"
keyword is present in extlinux.conf file, only if the command is supported.
This patch avoid the warning "Unknown command 'cls'"
with "menu background" in extlinux.conf when CONFIG_CMD_BMP is activated
and CONFIG_CMD_CLS not activated (default for CONFIG_DM_VIDEO).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support for read/write of ONIE "Tlvinfo" EEPROM data format. TLV
stands for Type-Length-Value. The data format is described here:
https://opencomputeproject.github.io/onie/design-spec/hw_requirements.html#board-eeprom-information-format
Based on U-Boot patch from the Open Compute project:
ec87e872d4/patches/u-boot/common/feature-sys-eeprom-tlv-common.patch
Keep only I2C EEPROM support. Use the generic eeprom driver. Fix
checkpatch issues.
Add support for multiple EEPROM TLV stores on the same system. This is
useful in case of SOM and carrier that both provide ID and hardware
configuration information.
Add option to enable for SPL. This allows selection of RAM configuration
based on EEPROM stored board identification.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
This is not really a CONFIG since it is not intended to be set by boards.
Move it into the compiler header with other similar defines, and rename
it.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function has a very generic name which does not adequately describe
its purpose. Rename it and move it to image.h, since it relates to reading
a script from an image.
Signed-off-by: Simon Glass <sjg@chromium.org>
These global variables are quite short and generic. In fact the same name
is more often used locally for struct members and function arguments.
Add a image_ prefix to make them easier to distinguish.
Signed-off-by: Simon Glass <sjg@chromium.org>
This seems pretty old now. It has not been converted to driver model and
is not used by any boards.
Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function belongs more in flash.h than common.h so move it.
Also remove the space before the bracket in some calls.
Signed-off-by: Simon Glass <sjg@chromium.org>
Until now, we only support aes128. This commit add the support
of aes192 and aes256.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the code, we use the size of the key for the
size of the block. It's true when the key is 128 bits,
but it become false for key of 192 bits and 256 bits.
So to prepare the support of aes192 and 256,
we introduce a constant for the iaes block size.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When no partition table is found, users should be warned so.
Warning that no device is available in this case could be misleading,
especially as it is the same error when no device is selected.
Signed-off-by: Alexandre Besnard <alexandre.besnard@softathome.com>
Trying to extend 'adtimg' functionality [1], we've been severely hit
by a major limitation in the command's usage scheme. Specifically, the
command's user interface appears to be too centric to getting the
DTB/DTBO entry [3] based on the index of the desired DT in the image,
which makes it really difficult retrieving the DT entry based on
alternative criteria (e.g. filtering by id/rev fields), the
latter being demanded by real life customer use-cases [1].
This went to the point of receiving below feedback from Sam [2]:
-- snip --
As for 'dtimg' command: after giving it some thought, I think not much
people using it yet. So in this particular case I don't have some
strong preference, and if you think the 'dtimg' interface is ugly, and
it overcomes "don't break interfaces" rule, maybe now is a good time
to rework it (before it gets widely used).
-- snip --
Given the above, rework the usage pattern from [4] to [5], in order to
allow an intuitive enablement of "by id|rev" DT search [6].
[1] https://patchwork.ozlabs.org/cover/1202575/
("cmd: dtimg: Enhance with --id and --rev options (take #1)")
[2] https://patchwork.ozlabs.org/patch/1182207/#2317020
[3] https://source.android.com/devices/architecture/dto/partitions
[4] Old usage
adtimg dump <addr> - Print image contents
adtimg start <addr> <index> <varname> - Get DT address by index
adtimg size <addr> <index> <varname> - Get DT size by index
[5] New usage
adtimg addr <addr> - Set image location to <addr>
adtimg dump - Print out image contents
adtimg get dt --index=<i> [avar [svar]] - Get DT address and size by index
[6] Soon-to-be-provided "by id|rev" add-on functionality
adtimg get dt --id=<id> --rev=<rev> [avar [svar [ivar]]]
- Get DT address/size/index by id|rev fields
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
With 'dtimg.c' renamed to 'adtimg.c', now ensure the naming
consistency in the internal implementation of 'adtimg.c'.
No functional change intended.
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rename the existing 'dtimg' command to 'adtimg', in order to:
- Suggest the Android origins and scope
- Be consistent with the upcoming 'abootimg' command (naming
suggested by Simon [*])
The change in _not_ backward compatible, but its benefits outweigh its
downsides, given that we don't expect active users of 'dtimg' today.
Perform the rename in several steps:
1. Rename *.c file and Kconfig symbol. This should allow
'git log --follow' to properly track the history of 'adtimg.c'
2. 's/dtimg/adtimg/g' in the internal namespace of 'adtimg.c'
ELF comparison [**] before and after shows no functional change.
[*] https://patchwork.ozlabs.org/patch/1182212/#2291600
[**] diff -u <(objdump -d cmd/dtimg.o) <(objdump -d cmd/adtimg.o)
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Simon Glass<sjg@chromium.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
If the numbers do not happen to contain any digits from [a-f], it's
not clear that they are base 16.
Signed-off-by: Klaus H. Sorensen <khso@prevas.dk>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
This pull request provides:
* support for FIT images for UEFI binaries
* drivers for hardware random number generators
* an implementation of the EFI_RNG_PROTOCOL
* a sub-command for efidebug to display configuration tables
-----BEGIN PGP SIGNATURE-----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=SjPV
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-04-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-04-rc1
This pull request provides:
* support for FIT images for UEFI binaries
* drivers for hardware random number generators
* an implementation of the EFI_RNG_PROTOCOL
* a sub-command for efidebug to display configuration tables
Per Enea OSE documentation, it supports some classes of ARM, PowerPC and
X86. Limit the option to those platforms.
Signed-off-by: Tom Rini <trini@konsulko.com>
For the RNG uclass we currently only have a test working on the sandbox.
Provide a command to test the hardware random number generator on
non-sandbox systems.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add support for booting EFI binaries contained in FIT images.
A typical usage scenario is chain-loading GRUB2 in a verified
boot environment.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When we hit a matching GUID we can directly return the text. There is no
need for a check after the loop.
efi_guid_t is defined as 8 byte aligned but GUIDs in packed structures do
not follow this alignment. Do not require the argument of get_guid_text()
to be correctly aligned.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When be launch a binary via bootefi the bootargs environment variable is
used to set the load options in the loaded image protocol.
Free memory allocated for load options when the UEFI binary exits.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Use a pointer to addressable memory instead of a "physical" address in the
virtual address space of the sandbox to efi_install_fdt().
Export the efi_install_fdt() function.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If the bootefi command is called without passing the address of a device
tree, the internal device tree is used. For devices with a hardware device
tree it is preferable to used the hardware device tree in this case.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
As part of moving the parsing of command line arguments to do_bootefi()
call efi_install_fdt() with the address of the device tree instead of a
string.
If the address is EFI_FDT_USE_INTERNAL (= 0), the internal device tree
is used.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
if MULTI_DTB_FIT is enabled it is helpful to display
the value of gd->multi_dtb_fit in bdinfo.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
When the `dfu` command is called from the U-Boot environment,
it now accepts an optional parameter that specifies a timeout (in seconds).
If a DFU connection is not made within that time the `dfu` command exits
(as it would if Ctrl+C was pressed). If the timeout is left empty or being
zero the `dfu` command behaves as it does now.
This is useful for allowing U-Boot to check to see if anything wants to
upload new firmware before continuing to boot.
The patch is based on the commit
5e966ccc3c
by Sebastien Colleur, which has been heavily reworked due to U-Boot changes
in the past.
Signed-off-by: Brad Campbell <bradjc5@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
In the future we may utilize optional argument in 'dfu' command line.
As a preparation for this, refactor do_dfu().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
The current 'fsp' command only works with FSP1. Update it to handle FSP2
as well. Convert everything to hex which is what U-Boot uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
On NixOS, cross compiled kernels have long suffixes that cause them to
exceed the current maximum path length. The PXE/TFTP max path length is
used for extlinux.conf support as well, which is where this problem
usually manifest's itself.
Signed-off-by: Ben Wolsieffer <benwolsieffer@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* Add Kconfig help describing the purpose of each command.
* Add CONFIG_CMD_MDIO so it could be selected individually, as
it doesn't depend on the mii command.
* Add Kconfig imply to mii to automatically select the mdio
command.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Part of the env cleanup moved this out of the environment code and into
the net code. However, this helper is sometimes needed even when the net
stack isn't included.
Move the helper to lib/net_utils.c like it's similarly-purposed
string_to_ip(). Also rename the moved function to similar naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reported-by: Ondrej Jirman <megous@megous.com>
In the next commit, rtc_mktime(), for compatibility with linux, will be
implemented using rtc_mktime(), which is no longer drivers/rtc specific.
So move this file under lib/.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Extract all sysboot command related code from pxe.c to new sysboot.c
Update Kconfig to insure that DISTRO_DEFAULT select new CMD_SYSBOOT
command.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
As sysboot and pxe commands are sharing piece of code, migrate this
common code into a new file pxe_utils.c to prepare sysboot command
code extraction from pxe.c
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The command cp fails on sandbox because the address is used
directly. To fix this issue, we call the function map_sysmem
to translate the address.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
The command iminfo fails on sandbox because the address
is used directly. To fix this issue, we call the function
map_sysmem to translate the address.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Defconfigs have been fixed, now we can add proper dependencies in
Kconfig. SPI FLASH is still not dependent on MTD (deeper rework needed).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The 'sf' command is not supposed to rely on the MTD stack, but both
'sf' and 'nand' commands use helpers located in mtd_uboot.c. Despite
their location, these functions do not depend at all on the MTD
stack.
This file (drivers/mtd/mtd_uboot.c) is only compiled if CONFIG_MTD is
selected, which is inconsistent with the current situation. Solve this
by moving these three functions (which are only used by the above two
commands) out of mtd_uboot.c and put them in a C file only compiled
with cmd/sf.c and cmd/nand.c.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Don't export get_part function now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Like in Linux, just use CONFIG_MTD to compile the MTD stack.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Add more clarity by changing the Kconfig entry name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
A type error in the implementation of the efidebug command is fixed.
-----BEGIN PGP SIGNATURE-----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=spg0
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-01-rc5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-01-rc5
A type error in the implementation of the efidebug command is fixed.
I detected the following error in sandbox with Clang on Travis CI:
+cmd/efidebug.c:703:15: error: result of comparison of constant
9223372036854775822 with expression of type 'int' is always false
[-Werror,-Wtautological-constant-out-of-range-compare]
+ else if (ret == EFI_NOT_FOUND)
+ ~~~ ^ ~~~~~~~~~~~~~
Simply changing a type of 'ret' to efi_status_t will fix this error.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
pxe command parses the init ramfs address(through initrd lable in
pxe config file), but is not passing it to bootm command as argument
as bootm_argc count is not increased.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When we do not have CONFIG_BLK (or SPL/TPL) enabled there are very few
cases where we need the blk_legacy code linked in. To catch these, build
when we have CONFIG_HAVE_BLOCK_DEVICE set. In addition, we only need
cmd/blk_common.o to be linked in when we have CONFIG_HAVE_BLOCK_DEVICE
set, so make use of that directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
These functions do not use driver model but are still used. Move them to a
new eeprom.h header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function is not defined by any boards so the feature is not used.
Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move these two functions into the irq_funcs.h header file. Also move
interrupt_handler_t as this is used by the irq_install_handler() function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions belong in cpu_func.h. Another option would be cache.h
but that code uses driver model and we have not moved these cache
functions to use driver model. Since they are CPU-related it seems
reasonable to put them here.
Move them over.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present this function sits in its own file but it does not really
justify it. There are similar string functions in vsprintf.h, so move it
there. Also add the missing function comment.
Use the vsprintf.h include file explicitly where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These don't need to be in common.h so move them out into a new header.
Also add some missing comments.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Drop inclusion of crc.h in common.h and use the correct header directly
instead.
With this we can drop the conflicting definition in fw_env.h and rely on
the crc.h header, which is already included.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some of these have a space before the bracket. Drop it to fix the style.
Add some missing function comments while here.
Note that u32 and u8 cannot be used here since crc.h is included on the
host side.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These should be moved to driver model, but in the meantime, move them
out of the common header to help reduce its size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
On the sandbox the UEFI binaries must match the host architectures.
Adjust the Makefiles. Provide the PE/COFF header and relocation files.
Allow building helloworld.efi on the sandbox.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Due to the commit 4b0bcfa7c4 ("Kconfig: Migrate CONFIG_BOOTM_* options")
BOOTEFI and BOOTEFI_HELLO_COMPILE (and other BOOTEFI configs) are
displayed in a long distance. This will make it difficult for us to
understand that those configurations are closely related.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
That option is currently not used by any defconfig and could not be set
anymore since it became mandatory to used Kconfig when introducing new
options with U-Boot v2016.11 or commit eed921d923 ("Kconfig: Add a
whitelist of ad-hoc CONFIG options") and commit 371244cb19 ("Makefile:
Give a build error if ad-hoc CONFIG options are added").
It was also not considered when fixing build warnings in
commit 39ac34473f ("cmd_mtdparts: use 64 bits for flash size,
partition size & offset") and could probably not be compiled anyway
after commit dfe64e2c89 ("mtd: resync with Linux-3.7.1"), which
renamed some members of struct mtd_info … so it was probably broken
since then, which was U-Boot v2013.07-rc1.
However it still seems to work, see example output below:
U-Boot 2019.10-00035-g06a9b259ca-dirty (Oct 30 2019 - 14:03:44 +0100)
CPU: SAMA5D27 1G bits DDR2 SDRAM
Crystal frequency: 24 MHz
CPU clock : 492 MHz
Master clock : 164 MHz
Model: ***
DRAM: 128 MiB
NAND: 256 MiB
Loading Environment from NAND... OK
In: serial@f8020000
Out: serial@f8020000
Err: serial@f8020000
Net: eth0: ethernet@f8008000
Hit keys 'tt' to stop autoboot (3 seconds).
U-Boot> mtdparts
device nand0 <atmel_nand>, # parts = 8
#: name size net size offset mask_flags
0: bootstrap 0x00040000 0x00040000 0x00000000 1
1: uboot 0x000c0000 0x000c0000 0x00040000 1
2: env1 0x00040000 0x00040000 0x00100000 0
3: env2 0x00040000 0x00040000 0x00140000 0
4: fpga_led 0x00040000 0x00040000 0x00180000 1
5: reserved 0x00040000 0x00040000 0x001c0000 1
6: rootfs_rec 0x03200000 0x03200000 0x00200000 1
7: filesystem 0x0cc00000 0x0cb80000 (!) 0x03400000 0
active partition: nand0,0 - (bootstrap) 0x00040000 @ 0x00000000
defaults:
mtdids : nand0=atmel_nand
mtdparts: mtdparts=atmel_nand:256k(bootstrap)ro,768k(uboot)ro,256k(env1),256k(env2),256k(fpga_led)ro,256k(reserved)ro,50M(rootfs_rec)ro,-(filesystem)
Signed-off-by: Alexander Dahl <ada@thorsis.com>
This declaration is not used anywhere in the whole tree. There is a
function 'mtd_id_parse()' which was renamed from 'id_parse()' in
commit 68d7d65100 ("Separate mtdparts command from jffs2"), but that
function is not used (anymore?) in cmd nand and build is fine without
that declaration, so it's probably just safe to remove.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Provide a better user interface for setting UEFI variables.
Bug fixes:
- ext4 file system not discovered on UEFI block device
- 'make tests' build error on 32bit systems
-----BEGIN PGP SIGNATURE-----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=f0m8
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-01-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-01-rc2
Provide a better user interface for setting UEFI variables.
Bug fixes:
- ext4 file system not discovered on UEFI block device
- 'make tests' build error on 32bit systems
Add optional parameter to 'avb verify' sub-command, so that user is able
to specify which slot to use, in case when user's partitions are
slotted. If that parameter is omitted, the behavior of 'avb verify' will
be the same as before, so user API is content.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Acked-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Add support of DFU for several interface/device
with one command.
The format for "dfu_alt_info" in this case is :
- <interface> <dev>'='alternate list (';' separated)
- each interface is separated by '&'
The previous behavior is always supported.
One example for NOR (bootloaders) + NAND (rootfs in UBI):
U-Boot> env set dfu_alt_info \
"sf 0:0:10000000:0=spl part 0 1;u-boot part 0 2; \
u-boot-env part 0 3&nand 0=UBI partubi 0,3"
U-Boot> dfu 0 list
DFU alt settings list:
dev: SF alt: 0 name: spl layout: RAW_ADDR
dev: SF alt: 1 name: ssbl layout: RAW_ADDR
dev: SF alt: 2 name: u-boot-env layout: RAW_ADDR
dev: NAND alt: 3 name: UBI layout: RAW_ADDR
U-Boot> dfu 0
$> dfu-util -l
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=3, name="UBI", serial="002700333338511934383330"
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=2, name="u-boot-env", serial="002700333338511934383330"
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=1, name="u-boot", serial="002700333338511934383330"
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=0, name="spl", serial="002700333338511934383330"
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
'THOR' download command requires DFU infrastructure to properly flash
board images. It can be used without enabling DFU command, so add such
dependency to Kconfig.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
With this patch, when setting UEFI variable with "env set -e" command,
we will be able to
- specify vendor guid with "-guid guid",
- specify variable attributes, BOOTSERVICE_ACCESS, RUNTIME_ACCESS,
respectively with "-bs" and "-rt",
- append a value instead of overwriting with "-a",
- use memory as variable's value instead of explicit values given
at the command line with "-i address,size"
If guid is not explicitly given, default value will be used.
Meanwhile, "env print -e," will be modified so that it will NOT dump
a variable's value if '-n' is specified.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If DM_SPI_FLASH enabled that means it is using sf command
for flash interface to access.
SPI_FLASH can be used via sf command and board/driver
functions to call spi flash ops, so mark it default only
for DM_SPI_FLASH.
This would prevent explicit adding of CONFIG_CMD_SF when
DM_SPI_FLASH being enabled.
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add Support for commands to initialize and configure UFS devices.
TODO: Add Support for commands to resize and reconfigure LUNs
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
ubi enhancements for 2020.01
- provide a way for skipping crc checks ported from linux, and add an
U-Boot command to set this flag on already installed systems.
- fix redundand environment management
U-Boot now supports the "skip_check" flag to optionally skip the CRC
check at open time. Currently its only possible to set this bit upon
UBI volume creation. But it might be very useful to also set this bit
on already installed systems (e.g. field upgrade) to make also use of
the boot-time decrease on those systems.
This patch now adds a new "ubi" command "ubi skipcheck" to set or clear
this bit in the UBI volume header:
=> ubi skipcheck rootfs0 on
Setting skip_check on volume rootfs0
BTW: This saves approx. 10 seconds Linux bootup time on a MT7688 based
target with 128MiB of SPI NAND.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Quentin Schulz <quentin.schulz@bootlin.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Dannenberg <dannenberg@ti.com>
Some users of static UBI volumes implement their own integrity check,
thus making the volume CRC check done at open time useless. For
instance, this is the case when one use the ubiblock + dm-verity +
squashfs combination, where dm-verity already checks integrity of the
block device but this time at the block granularity instead of verifying
the whole volume.
Skipping this test drastically improves the boot-time.
Adapted to U-Boot by Stefan Roese.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Quentin Schulz <quentin.schulz@bootlin.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
The aes command used to segfault when accessing memory in sandbox.
The pointer accesses should be mapped.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This patch uses auto instead of decimal in simple_strtoul().
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
If the ECC is enabled over the entire memory region, we need to ensure
the printf/put calls do not modify the stack after ECC is disabled.
Moved the printf/put statements after ECC is enabled.
Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
ecc_address_range registers contains the start address and end address
of the DDR address space. But the ddr cmd driver is assuming the register
contains the start address and size of the DDR address space. Because
of this some valid ecc addresses are errored out as invalid address.
Fix this calculation.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
- Rename existing FSP code to fsp1
- Add fsp2 directory in preparation to support FSP 2.0
- Various x86 platform codes update
- Various bug fixes and updates in dm core, sandbox and spl
The major corrections in this pull request are:
Fixes for the SetVariable() boot service.
Device path node for NVMe drives.
Disable CONFIG_CMD_NVEDIT by default.
-----BEGIN PGP SIGNATURE-----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=nzgb
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-01-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-01-rc1
The major corrections in this pull request are:
Fixes for the SetVariable() boot service.
Device path node for NVMe drives.
Disable CONFIG_CMD_NVEDIT by default.
All boards are using the same prompt that's why add it as default value to
Kconfig to simplify defconfigs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
All boards are using the same prompt that's why add it as default value to
Kconfig to simplify defconfigs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
At present the 'iod' command differs from 'md' in that it only shows a
single value. It is useful to see a dump of multiple values, particularly
when x86 peripherals contain register sets accessible via I/O ports.
Enhance the command to match md.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct multi-line comment format style]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Given these exported function an fsp_ prefix since they are declared in an
fsp.h header.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Since there is now a new version of the FSP and it is incompatible with
the existing version, move the code into an fsp1 directory. This will
allow us to put FSP v2 code into an fsp2 directory.
Add a Kconfig which defines which version is in use.
Some of the code in this new fsp1/ directory is generic across both FSPv1
and FSPv2. Future patches will address this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
With the patch below applied, host_block_dev structure was switched
to be placed in platdata rather than priv. The command "host info"
must be aligned with this change. Otherwise, we will see "Segmentation
Fault."
Fixes: 8f994c860d ("sandbox: blk: Switch to use platdata_auto_alloc_size for the driver data")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The growth of the UEFI sub-system leads to build failures for systems with
strict limits on the U-Boot image size.
CMD_NVEDIT_EFI supports displaying and editing of UEFI variables. The
setting is not needed for booting. Disabling it by default reduces the
size of the U-Boot image by 2 KiB.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
A wrong function name is referred to in a comment of do_env_set_efi().
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
At this point we are using part number sub-command to retrieve UUID
of the partition using it's name.
e.g.:
part number mmc $mmcdev system_a system_a_index
part uuid mmc $mmcdev:${system_a_index} system_a_uuid
Since 'part uuid' sub-command expects partition index in hex format and
'part number' returns decimal value, 'part uuid' command will provide
wrong UUID or fail.
Fixes: be683756f6 ("cmd: part: Add 'number' sub-command")
Cc: Dirk Behme <dirk.behme@de.bosch.com>
Reported-by: Pontus Fuchs <pontus.fuchs@se.bosch.com>
Signed-off-by: Roman Stratiienko <roman.stratiienko@globallogic.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Add support for capturing ethernet packets and storing
them in memory in PCAP(2.4) format, later to be analyzed by
any PCAP viewer software (IE. Wireshark)
This feature greatly assist debugging network issues such
as detecting dropped packets, packet corruption etc.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Tested-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The command "pci bar" and "pci region" display the address and size in
16 characters including "0x", so the command can only display
14 hexadecimal digits if the number of digits in the address and size is
less than 14.
ID Base Size Width Type
----------------------------------------------------------
0 0x00000020000000 0x00000000100000 64 MEM Prefetchable
1 0xffff000080000000 0x00000000100000 64 MEM Prefetchable
The 64-bit address and size should be displayed in 18(= 16+2) digits,
so this patch adjusts them.
Cc: Yehuda Yitschak <yehuday@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The assigned value NULL is overwritten before being used. Remove the
assignment.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Move the result variable into the struct also, so that it can be used when
BSS is not available. Add a function to read it.
Note that all functions sill use the BSS version of the data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This file contains lots of internal details about the environment. Most
code can include env.h instead, calling the functions there as needed.
Rename this file and add a comment at the top to indicate its internal
nature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Fixup apalis-tk1.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Avoid using a typedef here which is unnecessary. Add an 'env_' prefix to
both the enum and its members to make it clear that these are related to
the environment.
Add an ENV prefix to these two flags so that it is clear what they relate
to. Also move them to env.h since they are part of the public API. Use an
enum rather than a #define to tie them together.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an ENV prefix to these two flags so that it is clear what they relate
to. Also move them to env.h since they are part of the public API. Use an
enum rather than a #define to tie them together.
Signed-off-by: Simon Glass <sjg@chromium.org>
U-Boot is not supposed to use typedef for structs anymore. Also this name
is the same as the ENTRY() macro used in assembler files, and 'entry'
itself is widely used in U-Boot (>8k matches).
Drop the typedef and rename the struct to env_entry to reduce confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move these functions to the new header file and rename set_default_env()
to env_set_default() so that it has a consistent env_ prefix.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this function to the new header file and rename it so it has an env_
prefix.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This function fits better with the network subsystem, so move it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Joe Hershberger <joe.hershberger@ni.com>
Move env_set_hex() over to the new header file along with env_set_addr()
which uses it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move envmatch() over to the new header file. Also rename it to env_match()
to better line up with other functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move this function over to the new header file. Also rename it to have an
env_ prefix like the other functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
As part of the effort to remove things from common.h, create a new header
for the gzip functions. Move the function declarations to it and add
missing documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
FSP (CONFIG_HAVE_FSP) and Slim Bootloader (CONFIG_SYS_SLIMBOOTLOADER)
consume HOB (CONFIG_USE_HOB) data from the each HOB list pointer.
Add a common HOB library in lib/hob.c and include/asm/hob.h.
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Use existing EFI_GUID and efi_guid_t instead of struct efi_guid.
This is pre-work before making a common HOB library.
- Change 'struct efi_guid' to efi_guit_t
- Remove 'struct efi_guid'
- Define GUIDs with EFI_GUID() macro
- Use guidcmp() instead of compare_guid()
- Remove compare_guid()
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested on MinnowMax
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Registration of USB download gadget might fail for various reasons, so
add a check for g_dnl_register() funtion return value. Without this fix,
thor_init() will try to access the registered gadget structures resulting
in NULL pointer dereference issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
When building U-Boot with AVB enabled, compiler shows next warnings:
cmd/avb.c: In function 'do_avb_read_pvalue':
cmd/avb.c:371:18: warning: format '%ld' expects argument of type
'long int', but argument 2 has type 'size_t'
{aka 'unsigned int'} [-Wformat=]
printf("Read %ld bytes, value = %s\n", bytes_read,
~~^ ~~~~~~~~~~
%d
cmd/avb.c: In function 'do_avb_write_pvalue':
cmd/avb.c:404:19: warning: format '%ld' expects argument of type
'long int', but argument 2 has type '__kernel_size_t'
{aka 'unsigned int'} [-Wformat=]
printf("Wrote %ld bytes\n", strlen(value) + 1);
~~^ ~~~~~~~~~~~~~~~~~
%d
Fix those by using "%zu" specified.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
With this pull request a workaround for GRUB on 32bit ARM is re-enabled
and made customizable. Without the patch booting on ARM 32bit with GRUB
prior to version 2.04 or with a cache which is not managed via CP15
fails.
Further work will be needed to achieve a UEFI compliant cache handling.
According to the UEFI spec all caches except those that cannot be
managed via CP15 should be enabled.
An implementation of the ConvertPointer() runtime service is provided.
efi_crt0 is always rebuild to avoid having to call 'make mrproper' when
switching architectures.
-----BEGIN PGP SIGNATURE-----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=jfh5
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-10-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for v2019.10-rc2
With this pull request a workaround for GRUB on 32bit ARM is re-enabled
and made customizable. Without the patch booting on ARM 32bit with GRUB
prior to version 2.04 or with a cache which is not managed via CP15
fails.
Further work will be needed to achieve a UEFI compliant cache handling.
According to the UEFI spec all caches except those that cannot be
managed via CP15 should be enabled.
An implementation of the ConvertPointer() runtime service is provided.
efi_crt0 is always rebuild to avoid having to call 'make mrproper' when
switching architectures.
Since this is part of the autoboot functionality, it makes sense to name
it with an AUTOBOOT prefix. No mainline boards use it so this should be
safe, and downstream boards will need to adjust.
Since this option is just an integer value, it really needs another option
to control whether the feature is enabled or not. Add a new
CONFIG_USE_AUTOBOOT_MENUKEY for that. This fits better with how things are
done with Kconfig, avoiding the need to use a specific value to disable
the feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
- extend mxc_ipuv3_fb to enable backlight/display
- include fb_base in global_data for DM_VIDEO
- show frame buffer address via board info
as used to be with legacy VIDEO support
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXUCEtQ4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXLYhAJ4gSCCx54ubBmbsZ1cueGk59E/SkwCdFl7nfLqz
Vy/HbBVAUkzD4JVOR0U=
=7rSM
-----END PGP SIGNATURE-----
Merge tag 'video-for-2019.10-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-video
- fix EDID mode filtering
- extend mxc_ipuv3_fb to enable backlight/display
- include fb_base in global_data for DM_VIDEO
- show frame buffer address via board info
as used to be with legacy VIDEO support
make htmldocs produces a warning:
./cmd/efidebug.c:733: WARNING: Unexpected indentation.
Correct the indentation.
Remove 'See above for details of sub-commands.' which is not helpful in the
Sphinx generated documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
A couple minor tweaks to printed strings in cmd/fpga.c.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Linker generated array entry is not needed when the command line is
disabled. Remove this code in that case.
This is required as the commit 80a48dd47e
breaks the linking stage when CONFIG_CMDLINE=n:
..
LDS u-boot.lds
LD u-boot
u-boot contains unexpected relocations: R_ARM_NONE
R_ARM_RELATIVE
make: *** [Makefile:1775: checkarmreloc] Error 1
Signed-off-by: Andrej Rosano <andrej.rosano@f-secure.com>
'rproc list' is currently allowed only after probing all the
available remoteproc devices. Given that 'rproc init' is updated
to probe and initialize devices individually, allow the 'rproc list'
command to print all probed devices at any point.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
'rproc init' does the probe and initialization of all the available
remoteproc devices in the system. This doesn't allow the flexibility
to initialize the remote cores needed as per use case. In order
to provide flexibility, update 'rproc init' command to accept one
more parameter with rproc id which when passed initializes only
that specific core. If no id is passed, command will initializes
all the cores which is compatible with the existing behaviour.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
For A/B system update support the Android boot process requires to send
'androidboot.slot_suffix' parameter as a command line argument. This
patch implementes 'ab_select' command which allows us to obtain current
slot by processing the A/B metadata.
The patch was extracted from commit [1] with one modification: the
separator for specifying the name of metadata partition was changed
from ';' to '#', because ';' is used for commands separation.
[1] https://android-review.googlesource.com/c/platform/external/u-boot/+/729880/2
Signed-off-by: Ruslan Trofymenko <ruslan.trofymenko@linaro.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Alistair Strachan <astrachan@google.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
These have been reported by Simon in [1] and fixed in [2].
However, since [1] has already been pushed to u-boot/master, the
improvements incorporated in [2] are now extracted and resubmitted.
The changes are in the area of coding style and best practices:
* s/field/fieldp/, s/size/sizep/, to convey that the variables return
an output to the caller
* s/err_1/err_read_fail/, s/err_2/err_too_small/, to be more descriptive
* Made sure 'static int do_bcb_load' appears on the same line
* Placed a `/*` on top of multi-line comment
[1] https://patchwork.ozlabs.org/patch/1104244/#2200259
[2] https://patchwork.ozlabs.org/cover/1128661/
("[v4,0/4] Add 'bcb' command to read/modify/write Android BCB")
Fixes: db7b7a05b2 ("cmd: Add 'bcb' command to read/modify/write BCB fields")
Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Quote from https://patchwork.ozlabs.org/patch/1104244/#2210814:
----------8<-----------
strncmp() is chosen for the sake of paranoid/defensive programming.
Indeed, strncmp() is not really needed when comparing a variable
with a string literal. We expect strcmp() to behave safely even if the
string variable is not NUL-terminated.
In the same scenario, Linux v5.2-rc7 uses both strcmp() and strncmp(),
but the frequency of strcmp() is higher:
$ git --version
git version 2.22.0
$ (Linux 5.2-rc7) git grep -En 'strncmp\([^"]*"[[:alnum:]]+"' | wc -l
1066
$ (Linux 5.2-rc7) git grep -En 'strcmp\([^"]*"[[:alnum:]]+"' | wc -l
1968
A quick "strcmp vs strncmp" object size test shows that strcmp()
generates smaller memory footprint (gcc-8, x86_64):
$ (U-Boot) size cmd/bcb-strncmp.o cmd/bcb-strcmp.o
text data bss dec hex filename
3373 400 2048 5821 16bd cmd/bcb-strncmp.o
3314 400 2048 5762 1682 cmd/bcb-strcmp.o
So, overall, I agree to use strcmp() whenever variables are compared
with string literals.
----------8<-----------
Fixes: db7b7a05b2 ("cmd: Add 'bcb' command to read/modify/write BCB fields")
Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Fix warning V1037 reported by PVS-Studio Static Analyzer:
Two or more case-branches perform the same actions. Check lines: 49, 53
Fixes: db7b7a05b2 ("cmd: Add 'bcb' command to read/modify/write BCB fields")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Commit 9bdf0e8fef ("doc: relocate/rename Android README and add BCB
overview") left some obsolete references of Android documents/paths.
This has been pointed out by Sam (thanks!) in:
https://patchwork.ozlabs.org/patch/1104245/#2208134
Fixes: 9bdf0e8fef ("doc: relocate/rename Android README and add BCB overview")
Reported-by: Sam Protsenko <semen.protsenko@linaro.org>
Suggested-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
This sub-command serves for getting the partition index from
partition name. Also it can be used to test the existence of specified
partition.
Use case:
For example, in most CI environments this U-Boot command for automatic
testing of Linux rootfs is used:
=> setenv bootpart 1:f
where 0xf is "userdata" partition. But the number of "userdata"
partition can be changed any time, when partition table is changed.
So it would be nice to get rid of that 0xf magic number and use
partition name instead, like this:
=> part number mmc 1 userdata part_num
=> setenv bootpart 1:${part_num}
Signed-off-by: Ruslan Trofymenko <ruslan.trofymenko@linaro.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Alistair Strachan <astrachan@google.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
* Implement the EVT_SIGNAL_VIRTUAL_ADDRESS_CHANGE event.
* Address errors of type -Werror=address-of-packed-member when building
with GCC9.1
* Fix an error when adding memory add addres 0x00000000.
* Rework some code comments for Sphinx compliance.
-----BEGIN PGP SIGNATURE-----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=aj4j
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-10-rc1-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for v2019.10-rc1 (2)
* Implement the EVT_SIGNAL_VIRTUAL_ADDRESS_CHANGE event.
* Address errors of type -Werror=address-of-packed-member when building
with GCC9.1
* Fix an error when adding memory add addres 0x00000000.
* Rework some code comments for Sphinx compliance.
This commit just corrects spelling of 'accessed' word in the EEPROM
comment.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This option will provide the offset in the parallel NOR flash memory to,
which the falcon boot data is stored.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit makes the CMD_SPL_NAND_OFS only visible when we use NAND
memory.
Before this change it was present when only CMD_SPL was enabled (and
would stay when board with other falcon boot medium is used).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Calling 'mdio read ...' currently leads to a data abort when no mdio
bus is found.
To fix this, check if 'bus' is a valid pointer before accessing it.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
this patch adds basic changes for adding a erase-subcommand to env
with this command the environment stored on non-volatile storage written
by saveenv can be cleared.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
squashed fixes
- start message with "Erasing"
- mark erase-function as optional
- env: separate eraseenv from saveenv
Suggested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
We currently have some inconsistent use of efi_add_memory_map()
throughout the code. In particular the return value of efi_add_memory_map()
is not interpreted the same way by various users in the codebase.
This patch does the following:
- Changes efi_add_memory_map() to return efi_status_t.
- Adds a method description to efi_add_memory_map().
- Changes efi_add_memory_map() to return EFI_SUCCESS
- Returns non-zero for error in efi_add_memory_map()
- Updates efi_allocate_pages() to new efi_add_memory_map()
- Updates efi_free_pages() to new efi_add_memory_map()
- Updates efi_carve_out_dt_rsv() to new efi_add_memory_map()
- Updates efi_add_runtime_mmio() to new efi_add_memory_map()
Fixes: 5d00995c36 ("efi_loader: Implement memory allocation and map")
Fixes: 74c16acce3 ("efi_loader: Don't allocate from memory holes")
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Alexander Graf <agraf@csgraf.de>
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Adds UCLASS_MDIO DM class supporting MDIO buses that are probed as
stand-alone devices. Useful in particular for systems that support
DM_ETH and have a stand-alone MDIO hardware block shared by multiple
Ethernet interfaces.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
These are standard across gigabit phys. These mostly extend the
auto-negotiation information with gigabit fields.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Share the code that prints out a register field with the function that
prints out the "special" fields.
There were two arrays the register dump list, one with reg number and
name, another with a pointer to the field table and the table size.
These two arrays had have each entry match what register is referred to.
Combine them into just one table. Now they can't not match and there is
just one table.
Add some missing consts to pointers to string literals.
The dump code was ignoring the regno field in the description table and
assuming register 0 was at index 0, etc. Have it use the field.
Change reg > max+1 into reg >= max, which doesn't fail if max+1 could
overflow, besides just making more sense.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
- mmc spi driver model support
- drop mmc_spi command
- enhanced Strobe mmc HS400 support
- minor mmc bug/fixes and optimization
- omap hsmmc and mvbeu update
- sdhci card detect support
The mmc_spi command was added to manually setup MMC over SPI bus
using command. This was required by the legacy non-DM MMC_SPI driver.
With DM based MMC_SPI driver in-place, we can now use all general
storge commands and mmc command for MMC over SPI bus hence we remove
the mmc_spi command all it's references.
Suggested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add sub-command 'env info' to display environment information:
- env_valid : is environment valid
- env_ready : is environment imported into hash table
- env_use_default : is default environment using
This command can be optionally used for evaluation in scripts:
[-d] : evaluate whether default environment is used
[-p] : evaluate whether environment can be persisted
The result of multiple evaluations will be combined with AND.
Signed-off-by: Leo Ruan <tingquan.ruan@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Do not enable by default]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch solves the following warnings:
cmd/pinmux.c: In function 'do_dev':
cmd/pinmux.c:26:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (ret) {
^
cmd/pinmux.c:30:2: note: here
case 1:
^~~~
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- Minor tracing and PCI improvements
- Various other minor fixes
- Conversion of patman, dtoc and binman to support Python 3
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl0nbDoRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZcBQgAn+ojgq/hD89bihuhz2oEe6rhzHB9OkcC
sHrVL8Jbmby/BuzISGe4oeeM5yVygBVtUiN/72JiiAHLmykqc4CpRjNvgOOAgKCy
Ml8UyiBNNVNfrD6f9PxAKvPZf6S0gfLnomGOQ/psdEojpY5AvQxQ36D+QFZ0AMP5
67/xjSfN9bNPw8UbgE/VhJ+WFbU948BP2EBt6+NBAtv7HW4AX9vT0famJfWEjwq8
ftmcFOSNGgYcDQ5BwQWX1sFhnwb9XSfurlQsVYBsFA4cx4gj0DfUm1Ugr4wDD+lo
91P+76hSBQ+mHp1HJ90WMd2vAaElG7/SoaicXo9pW6Rc7WIgTjk7gg==
=SdZy
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-9jul19-take2' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
- Sandbox improvements including .dts refactor
- Minor tracing and PCI improvements
- Various other minor fixes
- Conversion of patman, dtoc and binman to support Python 3
'Bootloader Control Block' (BCB) is a well established term/acronym in
the Android namespace which refers to a location in a dedicated raw
(i.e. FS-unaware) flash (e.g. eMMC) partition, usually called "misc",
which is used as media for exchanging messages between Android userspace
(particularly recovery [1]) and an Android-capable bootloader.
On higher level, this allows implementing a subset of Android Bootloader
Requirements [2], amongst which is the Android-specific bootloader
flow [3]. Regardless how the latter is implemented in U-Boot ([3] being
the most memorable example), reading/writing/dumping the BCB fields in
the development process from inside the U-Boot is a convenient feature.
Hence, make it available to the users.
Some usage examples of the new command recorded on R-Car H3ULCB-KF
('>>>' is an overlay on top of the original console output):
=> bcb
bcb - Load/set/clear/test/dump/store Android BCB fields
Usage:
bcb load <dev> <part> - load BCB from mmc <dev>:<part>
bcb set <field> <val> - set BCB <field> to <val>
bcb clear [<field>] - clear BCB <field> or all fields
bcb test <field> <op> <val> - test BCB <field> against <val>
bcb dump <field> - dump BCB <field>
bcb store - store BCB back to mmc
Legend:
<dev> - MMC device index containing the BCB partition
<part> - MMC partition index or name containing the BCB
<field> - one of {command,status,recovery,stage,reserved}
<op> - the binary operator used in 'bcb test':
'=' returns true if <val> matches the string stored in <field>
'~' returns true if <val> matches a subset of <field>'s string
<val> - string/text provided as input to bcb {set,test}
NOTE: any ':' character in <val> will be replaced by line feed
during 'bcb set' and used as separator by upper layers
=> bcb dump command
Error: Please, load BCB first!
>>> Users must specify mmc device and partition before any other call
=> bcb load 1 misc
=> bcb load 1 1
>>> The two calls are equivalent (assuming "misc" has index 1)
=> bcb dump command
00000000: 62 6f 6f 74 6f 6e 63 65 2d 73 68 65 6c 6c 00 72 bootonce-shell.r
00000010: 79 00 72 00 00 00 00 00 00 00 00 00 00 00 00 00 y.r.............
>>> The output is in binary/string format for convenience
>>> The output size matches the size of inspected BCB field
>>> (32 bytes in case of 'command')
=> bcb test command = bootonce-shell && echo true
true
=> bcb test command = bootonce-shell- && echo true
=> bcb test command = bootonce-shel && echo true
>>> The '=' operator returns 'true' on perfect match
=> bcb test command ~ bootonce-shel && echo true
true
=> bcb test command ~ bootonce-shell && echo true
true
>>> The '~' operator returns 'true' on substring match
=> bcb set command recovery
=> bcb dump command
00000000: 72 65 63 6f 76 65 72 79 00 73 68 65 6c 6c 00 72 recovery.shell.r
00000010: 79 00 72 00 00 00 00 00 00 00 00 00 00 00 00 00 y.r.............
>>> The new value is NULL-terminated and stored in the BCB field
=> bcb set recovery "msg1:msg2:msg3"
=> bcb dump recovery
00000040: 6d 73 67 31 0a 6d 73 67 32 0a 6d 73 67 33 00 00 msg1.msg2.msg3..
00000050: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00000060: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
>>> --- snip ---
>>> Every ':' is replaced by line-feed '\n' (0xA). The latter is used
>>> as separator between individual commands by Android userspace
=> bcb store
>>> Flush/store the BCB structure to MMC
[1] https://android.googlesource.com/platform/bootable/recovery
[2] https://source.android.com/devices/bootloader
[3] https://patchwork.ozlabs.org/patch/746835/
("[U-Boot,5/6] Initial support for the Android Bootloader flow")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
The name CONFIG_LEGACY_IMAGE_FORMAT reads slightly better along with
allowing us to avoid a rather nasty Kbuild/Kconfig issue down the line
with CONFIG_IS_ENABLED(IMAGE_FORMAT_LEGACY). In a few places outside of
cmd/ switch to using CONFIG_IS_ENABLED() to test what is set.
Signed-off-by: Tom Rini <trini@konsulko.com>
There is no good reason to limit the trace buffer to 2GiB on a 64bit
system. Adjust the types of the relevant parameters.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This pull request provides error fixes for the graphical output protocol,
the text output protocol, and the extended text input protocol.
Setting the boot device for the bootefi command is now not only supported
by the 'load' command but also for the file system specific commands like
'fatload'.
-----BEGIN PGP SIGNATURE-----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=GvWF
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-07-rc5-3' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc5 (3)
This pull request provides error fixes for the graphical output protocol,
the text output protocol, and the extended text input protocol.
Setting the boot device for the bootefi command is now not only supported
by the 'load' command but also for the file system specific commands like
'fatload'.
