Commit graph

17 commits

Author SHA1 Message Date
Joe Hershberger
16879cd25a net: phy: Don't limit phy addresses by default
Some boards expect to find more than one phy while other boards are old
and need to be limited to a specific phy address. Only limit the phy
address for boards that opt in.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-04-13 15:56:47 -05:00
kevans@FreeBSD.org
66526e7038 net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys
Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off
on the PHY, as well as flipping some magical undocumented bits. The
magic number comes from the Pine64 engineering team, presumably as a
proxy from Realtek. This configuration fixes the throughput on some
Pine64 models. Packet loss of up to 60-70% has been observed without
this.

Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22 15:05:27 -05:00
Stefan Mavrodiev
b30c419040 Move CONFIG_PHY_ADDR to Kconfig
CONFIG_PHY_ADDR is used for old-style configuration. This makes
impossible changing the PHY address, if multiple boards share a same
config header file (for example include/configs/sunxi-common.h).

Moving this to Kconfig helps overcoming this issue. It's defined
as entry inside PHYLIB section.

After the implemention, moveconfig was run. The issues are:
	- edb9315a	- CONFIG_PHYLIB is not enabled. Entry is
			  deleted.

	- ds414		- CONFIG_PHYLIB is in incompatible format:
			  { 0x1, 0x0 }. This entry is also deleted.

	- devkit3250	- The PHY_ADDR is in hex format (0x1F).
			  Manually CONFIG_PHY_ADDR=31 is added in
			  the defconfig.

After the changes the suspicious defconfigs passes building.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[jagan: rebased on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-03-13 22:36:33 +05:30
Michal Simek
c946b0e9fd Kconfig: net: phylib: Phylib should depends on NET
There is no value to enable phylib without networking support.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-02-08 12:48:10 -05:00
Florian Fainelli
137963d71a net: phy: Add Broadcom BCM53xx switch driver
Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar
to the Marvell MV88E617x. This takes care of configuring the minimum
amount out of the switch hardware such that each user visible port
(configurable) and the CPU port can forward packets between each other
while preserving isolation with other ports.

This is useful for e.g: the Lamobo R1 board featuring a Broadcom
BCM53125 switch.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2018-01-15 12:05:21 -06:00
Neil Armstrong
8995a96d1d net: phy: Add Amlogic Meson GXL Internal PHY support
The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY.

The PHY acts as a generic PHY but needs a slight configuration right
before it's configuration.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2017-11-17 07:44:13 -05:00
Alexandru Gagniuc
9a31c739d2 net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options
The correct option is PHY_MICREL_KSZ90X1, but some configs still
select the 9021 and 9031 options, which are deprecated.

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-08-07 15:18:30 -05:00
Alexandru Gagniuc
d397f7c45b net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers
The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they
share the same ID. Drivers for bothe PHYs cannot safely coexist, so
the solution was to use #ifdefs to select between the two drivers.

As a result KSZ9031, which has a unique ID, is now caught in the
crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031
will not function properly, as some essential configuration code is
ifdef'd-out.

To prevent such situations, move the KSZ9000 drivers to a separate
file, and place them under a separate Kconfig option. While it is
possible to enable both KSZ8000 and KSZ9000 drivers at the same time,
the assumption is that it is highly unlikely for a system to contain
both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers
will be enabled at any given time.

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-08-07 15:18:30 -05:00
Alexandru Gagniuc
cb543d30df net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-08-07 15:18:29 -05:00
Tom Rini
821560fd8e Merge git://www.denx.de/git/u-boot-imx
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	include/configs/imx6qdl_icore_rqs.h
	include/configs/imx6ul_geam.h
	include/configs/imx6ul_isiot.h
2017-06-27 09:32:37 -04:00
Philipp Tomsich
449ea2cd0d net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable
This change migrate the following configuration options for Kconfig:
 * PHY_GIGE, indicates that a controller (with an appropriate PHY) is
   Gigabit capable and enables extra support in the miiutil for
   parsing the status of Gigabit PHYs
 * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs,
   which previously had to enabled through a board-specific config file

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-06-02 14:44:18 -05:00
Jagan Teki
a43241a406 drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry
Add kconfig entry for Micrel KSZ9021 PHY support.

Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-05-31 10:22:14 +02:00
Tom Rini
1622559066 Merge branch 'master' of git://www.denx.de/git/u-boot-imx
Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-13 11:19:00 -04:00
Hannes Schmelzer
db40c1aa1c drivers/net/phy: add fixed-phy / fixed-link support
This patch adds support for having a "fixed-link" to some other MAC
(like some embedded switch-device).

For this purpose we introduce a new phy-driver, called "Fixed PHY".

Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is
described with a subnode below ethernet interface.

Most ethernet drivers (unfortunately not all are following same scheme
for searching/attaching phys) are calling "phy_connect(...)" for getting
a phy-device.
At this point we link in, we search here for a subnode called "fixed-
link", once found we start phy_device_create(...) with the special phy-
id PHY_FIXED_ID (0xa5a55a5a).

During init the "Fixed PHY" driver has registered with this id and now
gets probed, during probe we get all the details about fixed-link out of
dts, later on the phy reports this values.

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2017-03-26 09:58:26 -05:00
Tim Harvey
b4f4b0f54b drivers: net: phy: add MV88E6xx options to Kconfig
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-03-20 19:09:49 +01:00
John Haechten
a5fd13ad19 net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541
Signed-off-by: John Haechten <john.haechten@microsemi.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-02-08 16:32:58 -06:00
Alex
af2cbfd6b9 drivers: net: Provide Kconfig menu for PHYLIB
Provide the necessary Kconfig symbols so that PHYLIB support may be
enabled in Kconfig, as opposed to needing to #define these symbols in
C source headers.

BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as
they don't seem to explicitly depend on it (i.e. they do not use the
phy_driver class).

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-02-07 11:05:03 -06:00