1. use Payload length check disable when enable MAC;
2. add XGMII support for setting MAC interface mode;
3. only enable auto negotiation for Non-XGMII mode;
4. return 0xffff if clause 22 is used to read 10G phy_id;
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-By: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
mcc200 and prs200 are old and have no maintainer. Remove the boards.
This also removes the mcc200 specific 1bpp BMP support from
common/lcd.c
Cc: Wolfgang Denk <wd@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
ppc4xx i2c master gets stuck on errors while repeated start is
active. Can be easily reproduced by "i2c md" on an unpopulated
i2c address. There is not stop condition given, scl remains
pulled low.
The only way out seems to be doing a stop manually and then a
soft reset.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
There are a number of places where U-Boot intentionally and legally
accesses physical address 0x0000, for example when installing
exception vectors on systems where these are located in low memory.
Add "cppcheck-suppress nullPointer" comments to silence cppcheck
where this is intentional and legal.
Signed-off-by: Wolfgang Denk <wd@denx.de>
I realized that with v2014.10 u-boot is not starting up on
ppc4xx boards with CONFIG_SYS_GENERIC_BOARD set.
I bisected it down to this:
d54d7eb support blackfin board initialization in generic board_f
With
d29437a ppc: Make ppc4xx ready for CONFIG_SYS_GENERIC_BOARD
I set gd to a defined value for ppc4xx in cpu_init_f().
I did not realize that the gd struct has also to be memset()
to zero at this point.
But at least commit d54d7eb assumes it is:
@@ -516,11 +528,13 @@ static int reserve_malloc(void)
/* (permanently) allocate a Board Info struct */
static int reserve_board(void)
{
- gd->start_addr_sp -= sizeof(bd_t);
- gd->bd = (bd_t *)map_sysmem(gd->start_addr_sp, sizeof(bd_t));
- memset(gd->bd, '\0', sizeof(bd_t));
- debug("Reserving %zu Bytes for Board Info at: %08lx\n",
- sizeof(bd_t), gd->start_addr_sp);
+ if (!gd->bd) {
+ gd->start_addr_sp -= sizeof(bd_t);
+ gd->bd = (bd_t *)map_sysmem(gd->start_addr_sp, sizeof(bd_t));
+ memset(gd->bd, '\0', sizeof(bd_t));
+ debug("Reserving %zu Bytes for Board Info at: %08lx\n",
+ sizeof(bd_t), gd->start_addr_sp);
+ }
return 0;
}
#endif
This might also be an issue on other architectures, so maintainers should
check.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Commit d58a9451e7 (ppc/arm: zap EMK boards) removed
TOP* boards support but missed to remove entries in Kconfig.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
The following bard configurations have been without active maintenance
for a long time, and the board maintainer agrees to have them removed:
MPC5200: TOP5200, MINI5200, EVAL5200
MPC860: TOP860
at91sam9xeXXX: top9000eval_xe, top9000su_xe
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de>
[trini: Add missing Kconfig removals]
Signed-off-by: Tom Rini <trini@ti.com>
CONFIG_TPL should not be enabled for boards that do not have TPL.
CONFIG_SUPPORT_TPL introduced by this commit should be "select"ed
by boards with TPL support and CONFIG_TPL should depend on it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
CONFIG_SPL should not be enabled for boards that do not have SPL.
CONFIG_SUPPORT_SPL introduced by this commit should be "select"ed
by boards with SPL support and CONFIG_SPL should depend on it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
This board is old and is using CONFIG_I2C_X, which is wrong.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
This board is old and is using CONFIG_I2C_X, which is wrong.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
This board is old and is using CONFIG_I2C_X, which is wrong.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
This is the only used of CONFIG_SPI_X macro, just zap this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Remove this board as this is the only one last user of eeprom_probe(),
which is pretty non-standard stuff.
This patch also removes all the PHP, SQL and CSS stuff from U-Boot,
which probably makes U-Boot a bit less IoT ;-)
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
This board uses eeprom accessors in an incorrect way. The board
is old and unsupported, just zap it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
This board is the only user of CONFIG_SYS_EEPROM_X40430 , remove
it so the EEPROM command code can be cleansed of the related code
as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
The file board/Marvell/include/mv_gen_reg.h is incompatible with
the GPL (see for example the "MARVELL RESERVES THE RIGHT AT ITS SOLE
DISCRETION TO REQUEST THAT THIS CODE BE IMMEDIATELY RETURNED TO
MARVELL" clause). As this cannot be fixed, we remove the file and all
code that depends on it. Fortunately this only affects some very old
boards that have long reached EOL:
CPCI750
DB64360
DB64460
p3m750
p3m7448
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Roger Meier <r.meier@siemens.com>
Commit d6b11fd1 (powerpc: remove MBX and MBX860T boards support)
removed mbxbar field in "struct sysconf512x" by mistake and broke
booting on mpc5121 boards. Fix it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
By default, PAMU's (IOMMU) are enabled in case of secure boot.
Disable/bypass them once the control reaches the bootloader.
For non-secure boot, PAMU's are already bypassed in the default
SoC configuration.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SHA-256 and SHA-1 accelerated using SEC hardware in Freescale SoC's
The driver for SEC (CAAM) IP is based on linux drivers/crypto/caam.
The platforms needto add the MACRO CONFIG_FSL_CAAM inorder to
enable initialization of this hardware IP.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SEC registers can be of type Little Endian or big Endian depending upon
Freescale SoC. Here SoC defines the register type of SEC IP.
So update acessor functions with common SEC acessor functions to take care
both type of endianness.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale SEC controller has been used for mpc8xxx. It will be used
for ARM-based SoC as well. This patch moves the CCSR defintion of
SEC to common include
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This board has been orphaned for more than 6 months.
It is the last board defining CONFIG_APM821XX.
The code inside #ifdef CONFIG_APM821XX should be removed too.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
With some versions of gcc (that we know of 4.6.3 and 4.8.2 are affected)
it is necessary to specify --bss-plt to get the final blrl in the
_GOT2_TABLE_. Without this the last symbol does not get it's address
relocated. For the P2041RDB board this ended up being
NetArpWaitTimerStart which caused the ARP packets to timeout
immediately.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
U-boot has been initializing DDR for the main memory. The presumption
is the memory stays as a big continuous block, either linear or
interleaved. This change is to support putting some DDR controllers
to separated space without counting into main memory. The standalone
memory controller could use different number of DIMM slots.
Signed-off-by: York Sun <yorksun@freescale.com>
Each CPU of PowerPC has its default linker script under the CPU
directory, except mpc8xx.
Every mpc8xx board has its own linker script under the board
directory, resulting in lots of duplication of linker scripts.
I notice eight mpc8xx boards have the same linker script.
We can decrease the number of linker scripts by putting a single
default linker script, arch/powerpc/cpu/mpc8xx/u-boot.lds.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
"0x00" is a valid serdes protocol for QorIQ parts, and can not be
used to test whether the serdes is enabled or disabled.
Signed-off-by: Ebony Zhu <b45385@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Fix following issues in USB device-tree fixup:
- returns when either dr_mode or phy_type not defined.
This was terminating fix-up when only either property
was defined in hwconfig string
- updates dr_mode_type or dr_phy_type with junk value when
their index is -1. Now these are updated only when their
respective index is pointing to relevant types
in modes[] and phys[] array
- dr_mode_type and dr_phy_type were not NULL for
each controller
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME}
are specified in arch/Kconfig.
We can delete the ones in arch and board Kconfig files.
This commit can be easily reproduced by the following command:
find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e '
/config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ {
N
s/\n[[:space:]]*string//
}
'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
fsl_enet.h defines the mapping of the usual MII management
registers, which are included in the MDIO register block
common to Freescale ethernet controllers. So it shouldn't
depend on the CPU architecture but it should be actually
part of the arch independent fsl_mdio.h.
To remove the arch dependency, merge the content of
asm/fsl_enet.h into fsl_mdio.h.
Some files (like fm_eth.h) were simply including fsl_enet.h
only for phy.h. These were updated to include phy.h instead.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Some drivers (e.g. net/e1000) reference these functions. So, this
fixes the build of MVBC_P board.
I'm not familiar with the MPC5xxx platform, maybe a full
implementation shall be implemented instead of this stub in the
future.
Signed-off-by: Vasili Galka <vvv444@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>, Marek Vasut <marex@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
If hwconfig does not contains "en_cpc" then by default all cpcs are enabled
If this config is defined then only those individual cpcs which are defined
in the subargument of "en_cpc" will be enabled e.g en_cpc:cpc1,cpc2; (this
will enable cpc1 and cpc2) or en_cpc:cpc2; (this enables just cpc2)
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add deep sleep support in SPI/SD boot. The destination address
second stage uboot image is loaded to is changed because
currently this address will be used by kernel which means
we can't reserve it for resume.
Entry point to kernel is still placed in second stage uboot.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
bootflag as a parameter is passed to board_init_f().
But it is not actually used in this function.
Make it effective by assigned it to gd->flags.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When CONFIG_WATCHDOG is defined the board initialization just performs
a WATCHDOG_RESET, an initialization of the watchdog is not done.
This has been modified fot the MPC85xx, the board initialization calls
its watchdog initialitzation allowing for full watchdog configuration
very early in the boot phase.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Function to inititialize the cpu watchdog added.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
[York Sun: Add prototype in watchdog.h]
Reviewed-by: York Sun <yorksun@freescale.com>
For e500mc cores the watchdog timer period has to be set by means of a
6bit value, that defines the bit of the timebase counter used to signal
a watchdog timer exception on its 0 to 1 transition.
The macro used to set the watchdog period TCR_WP, was redefined for e500mc
to support 6 WP setting.
The parameter (x) given to the macro specifies the prescaling factor of
the time base clock (fTB):
watchdog_period = 1/fTB * 2^x
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
TCR watchdog bit are overwritten when dec interrupt is enabled.
This has been fixed with this patch.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
CONFIG_${CPU} is defined by Kconfig.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefan Roese <sr@denx.de>
This commit enables Kconfig.
Going forward, we use Kconfig for the board configuration.
mkconfig will never be used. Nor will include/config.mk be generated.
Kconfig must be adjusted for U-Boot because our situation is
a little more complicated than Linux Kernel.
We have to generate multiple boot images (Normal, SPL, TPL)
from one source tree.
Each image needs its own configuration input.
Usage:
Run "make <board>_defconfig" to do the board configuration.
It will create the .config file and additionally spl/.config, tpl/.config
if SPL, TPL is enabled, respectively.
You can use "make config", "make menuconfig" etc. to create
a new .config or modify the existing one.
Use "make spl/config", "make spl/menuconfig" etc. for spl/.config
and do likewise for tpl/.config file.
The generic syntax of configuration targets for SPL, TPL is:
<target_image>/<config_command>
Here, <target_image> is either 'spl' or 'tpl'
<config_command> is 'config', 'menuconfig', 'xconfig', etc.
When the configuration is done, run "make".
(Or "make <board>_defconfig all" will do the configuration and build
in one time.)
For futher information of how Kconfig works in U-Boot,
please read the comment block of scripts/multiconfig.py.
By the way, there is another item worth remarking here:
coexistence of Kconfig and board herder files.
Prior to Kconfig, we used C headers to define a set of configs.
We expect a very long term to migrate from C headers to Kconfig.
Two different infractructure must coexist in the interim.
In our former configuration scheme, include/autoconf.mk was generated
for use in makefiles.
It is still generated under include/, spl/include/, tpl/include/ directory
for the Normal, SPL, TPL image, respectively.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds:
- arch/${ARCH}/Kconfig
provide a menu to select target boards
- board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
set CONFIG macros to the appropriate values for each board
- configs/${TARGET_BOARD}_defconfig
default setting of each board
(This commit was automatically generated by a conversion script
based on boards.cfg)
In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.
But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
The generic board infrastructure assumes that gd is set by
arch code.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
At present stdio device functions do not get any clue as to which stdio
device is being acted on. Some implementations go to great lengths to work
around this, such as defining a whole separate set of functions for each
possible device.
For driver model we need to associate a stdio_dev with a device. It doesn't
seem possible to continue with this work-around approach.
Instead, add a stdio_dev pointer to each of the stdio member functions.
Note: The serial drivers have the same problem, but it is not strictly
necessary to fix that to get driver model running. Also, if we convert
serial over to driver model the problem will go away.
Code size increases by 244 bytes for Thumb2 and 428 for PowerPC.
22: stdio: Pass device pointer to stdio methods
arm: (for 2/2 boards) all +244.0 bss -4.0 text +248.0
powerpc: (for 1/1 boards) all +428.0 text +428.0
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
When resume from deep sleep, uboot needs to enable L2 and CPC
cache, or they would be keeping unusable in kernel because
kernel didn't enble or initialized them.
This patch didn't change the existing L2 cache enabling code,
just put them in a function.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T4240 has 4 serdes, each serdes has 4k memory space, two PLLs.
We use PLL1CR0 to check the serdes reference clock.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Previously the driver was only tested on Power SoCs. Different barrier
instructions are needed for ARM SoCs.
Signed-off-by: York Sun <yorksun@freescale.com>
ls1021 is arm-core and supports qe too.
Move immap_qe.h into common directory for both arm and powerpc.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
On some SoC(e.g. T2080/T4240) the 3rd DMA is not functional if SRIO2 is
chosen. we add fdt_fixup_dma3() to disable the 3rd DMA if SRIO2 is chosen.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Since ARRAY_SIZE macro is defined in include/common.h,
re-defining it in arch-specific files is redundant.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Remove the common infrastructure of nand_spl and
clean-up the code inside ifdef(CONFIG_NAND_U_BOOT)..endif.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This is a workaround for 32 bit hardware limitation of TDM.
T1040 has 36 bit physical addressing, TDM DMAC register
are 32 bit wide but need to store address of CCSR space
which lies beyond 32 bit address range. This workaround
creats a LAW to enable access of TDM DMA to CCSR by
mapping CCSR to overlap with DDR.
A hole of 16M is created in memory using device tree. This
workaround law is set only if "tdm" is defined in hwconfig.
Also disable POST tests and add LIODN for TDM
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SerDes PLL is calibrated at reset. When the junction temperature
delta from the time the PLL is calibrated exceeds +56C/-66C,
jitter may increase and can cause PLL to unlock.
This workaround overwrite the SerDes registers with new values,
to calibrate SerDes registers.
These values are known to work fine for all temperature ranges.
This workaround is valid for B4, T4 and T2 platforms, so
added in their config.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com>
[York Sun: replaced typedef ccsr_sfp_regs_t with struct ccsr_sfp_regs]
Reviewed-by: York Sun <yorksun@freescale.com>
When the DDR controller is initialized below a junction temperature of
0°C and then operated above a junction temperature of 65°C, the DDR
controller may cause receive data errors, resulting ECC errors and/or
corrupted data. This erratum applies to the following SoCs and their
variants: MPC8536, MPC8569, MPC8572, P1010, P1020, P1021, P1022, P1023,
P2020.
Signed-off-by: York Sun <yorksun@freescale.com>
A-007186: SerDes PLL is calibrated at reset. It is possible for jitter to
increase and cause the PLL to unlock when the temperature delta from the
time the PLL is calibrated exceeds +56C/-66C when using X VDD of 1.35 V
(or +70C/-80C when using XnVDD of 1.5 V). No issues are seen with LC
VCO. Only the protocols using Ring VCOs are impacted.
Workaround:
For all 1.25/2.5/5 GHz protocols, use LC VCO instead of Ring VCO, this need
to use alternate serdes protocols. The alternate option has the same
functionality as the original option; the only difference being LC VCO
rather than Ring VCO.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As errata A-007186, we need to use the alternate serdes
protocol instead of those impacted protocols.
- add support for serdes protocols: 0x1b, 0x50, 0x5e,
0x64, 0x6a, 0xd2, 0x67, 0x70.
- update t2080_rcw.cfg to adapt to new rcw_66_15 for
t2080qds and t2080rdb.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)
Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>
This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)
Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>
This code seems unnecessarily complex. We really just need to check the
global_data. Now that is it all in one place, and not arch-specific, this
is pretty easy.
Signed-off-by: Simon Glass <sjg@chromium.org>
P1020 SoC which has two USB controllers, but only first one is used
on this platform.
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
B4460 differs from B4860 only in number of CPU cores,
hence used existing support for B4860.
B4460 has 2 PPC cores whereas B4860 has 4 PPC cores.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
By default, all PEX inbound windows PEX_PEXIWARn[TRGT] are
mapped to 0xF, which is local memory. But for BSC9132, 0xF
is CCSR, 0x0 is local memory.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The argument boot_flag of board_inti_f() hasn't been used for powerpc until
recent changing to use generic board. Set it to 0 as a proper value.
Signed-off-by: York Sun <yorksun@freescale.com>
baord_init_f takes one argument, boot_flag. It has not been used for
powerpc, until recently changing to use generic board architecture.
The boot flag is added as a return value from cpu_init_f().
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alexander Graf <agraf@suse.de>
The pointer of device tree comes from r3 for QEMU. This is not the case
for normal SoCs out of reset. Having gd->fdt_blob as 0 is important for
other functions to detect the non-existence of device tree.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alexander Graf <agraf@suse.de>
We want to use the TLB mapping helpers in relocated mode as well. These helpers
need to have awareness of already occupied TLB entries. We already had them in
sync in non-relocated mode, but need to resync them when we move into relocated.
Signed-off-by: Alexander Graf <agraf@suse.de>
For the QEMU machine type, we can plug in either e500v2, e500mc, e5500
or e6500 style cores into the system. U-boot has to work with all of them.
So avoid using HID1 which is not available on e500mc systems to make sure
we don't trap on it.
Signed-off-by: Alexander Graf <agraf@suse.de>
We only need u-boot to bother about a single core in the QEMU machine.
Everything that would require additional knowledge of more cores gets
handled by QEMU and passed straight into the payload we execute.
Because of this setup, it would be counterproductive to enable SMP support
in u-boot. We would have to rip CPUs out of already existing spin tables
and respin them from u-boot. It would be a pretty big mess.
So only assume we have a single core. This fixes errors about CONFIG_MP
being disabled.
Signed-off-by: Alexander Graf <agraf@suse.de>
The T4080 SoC is a low-power version of the T4160.
T4080 combines 4 dual-threaded Power Architecture e6500
cores with single cluster and two memory complexes.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Secure Boot Target is added for T2080RDB
Changes:
For Secure boot, CPC is configured as SRAM and used as house
keeping area which needs to be disabled.
So CONFIG_SYS_CPC_REINIT_F is defined for CONFIG_T2080RDB.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
T1040RDB.h file is removed and a unified file T104xRDB.h is created.
Hence macro CONFIG_T1040 is renamed to CONFIG_T104x.
Signed-off-by: Gaurav Kumar Rana <gaurav.rana@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
T4240RDB board Specification
----------------------------
Memory subsystem:
6GB DDR3
128MB NOR flash
2GB NAND flash
Ethernet:
Eight 1G SGMII ports
Four 10Gbps SFP+ ports
PCIe:
Two PCIe slots
USB:
Two USB2.0 Type A ports
SDHC:
One SD-card port
SATA:
One SATA port
UART:
Dual RJ45 ports
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: fix CONFIG_SYS_QE_FMAN_FW_ADDR in T4240RDB.h]
CONFIG_BOARDDIR is not referenced in these linker scripts.
The comment /* CONFIG_BOARDDIR */ is misleading.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
gd->bd->bi_baudrate is a copy of gd->baudrate.
Since baudrate is a common feature for all architectures,
keep gd->baudrate only.
It is true that bi_baudrate was passed to the kernel in that structure
but it was a long time ago.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu> (For microblaze)
mpc831x has no muram, so muram cannot be used for bootcounter
function.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
B4420 is a personality of B4860.
It should have same FM1_CLK_SEK and FM1_CLK_SHIFT as B4860
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Adds support for clock sourcing from sysclk(100MHz) for usb
on T104xRDB and T1040QDS. This requires changing reference divisor
and multiplication factor to derive usb clock from sysclk.
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1040 and it's variants provide "Single Oscillator Source" Reference Clock Mode.
In this mode, single onboard oscillator(DIFF_SYSCLK) can provide the reference clock
(100MHz) to the following PLLs:
• Platform PLL
• Core PLLs
• USB PLL
• DDR PLL, etc
The cfg_eng_use0 of porsr1 register identifies whether the SYSCLK (single-ended) or
DIFF_SYSCLK (differential) is selected as the clock input to the chip.
get_sys_info has been enhanced to add the diff_sysclk so that the
various drivers can be made aware of ths diff sysclk configuration and
act accordingly.
Other changes:
-single_src to ddr_refclk_sel, as it is use for checking ddr reference clock
-Removed the print of single_src from get_sys_info as this will be
-printed whenever somebody calls get_sys_info which is not appropriate.
-Add print of single_src in checkcpu as it is called only once during initialization
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
It is not necessary for bootpg to be present at text + 512KB.
With increase of u-boot size (768KB), bootpg section's address
cannot be fixed.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Before parsing LAW table i.e. init_law, boot loader should disable all
previous LAWs except DDR LAWs which has been created by previous
pre boot loader during DDR initialization.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Current SPL code base has BSS section placed after reset_vector. This means
they have to relocate to use the global variables. This put an implicit
requirement of having SPL size = Memory/2.
To avoid relocation:
- Move bss_section within SPL range
- Modify relocate_code()
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SPL linker has fix location of bootpg and reset vector with respect to text base.
It is not necessary to have fixed locations.
Avoid such hardcoding.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LAW_EN is only defined if CONFIG_SYS_CCSRBAR_DEFAULT is not equal to
CONFIG_SYS_CCSRBAR_PHYS. in SPL framework CCSRBAR is not relocated hence
both are same. This cause compilation error.
So LAW_EN define outside of configs
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
qe_init() does not use data copied from NAND. Thise code is not tested or
complied causing compilation error during NAND boot
So, remove QE firmware copy from NAND to ddr.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When T104x soc wakes up from deep sleep, control is passed to the
primary core that starts executing uboot. After re-initialized some
IP blocks, like DDRC, kernel will take responsibility to continue
to restore environment it leaves before.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The supplement configuration unit (SCFG) provides chip-specific
configuration and status registers for the device. It is the chip
defined module for extending the device configuration unit (DCFG)
module. It provides a set of CCSR registers in addition to those
available in the device configuration unit.
The base address for this unit is 0x0F_C000.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1040RDB and T1040QDS boards have an integrated l2 switch.
The switch needs a MAC address for Layer 2 protocols
(MSTP, LLDP, LACP, etc). Setting a MAC address on l2switchaddr will add
a MAC in device-tree, under node l2switch.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Erratum A007212 for DDR is about a runaway condition for DDR PLL
oscilliator. Please refer to erratum document for detail.
For this workaround to work, DDR PLL needs to be disabled in RCW.
However, u-boot needs to know the expected PLL ratio. We put the
ratio in a reserved field RCW[18:23]. U-boot will skip this workaround
if DDR PLL ratio is set, or the reserved field is not set.
Workaround for erratum A007212 applies to selected versions of
B4/T4 SoCs. It is safe to apply the workaround to all versions. It
is helpful for upgrading SoC without changing u-boot. In case DDR
PLL is disabled by RCW (part of the erratum workaround), we need this
u-boot workround to bring up DDR clock.
Signed-off-by: York Sun <yorksun@freescale.com>
Put a delay of 5 millisecond after reset so that ULPI phy
gets enough time to come out of reset. Erratum A007075 applies
to following SOCs and their variants, if any
P1010 rev 1.0
B4860 rev 1.0, 2.0
P4080 rev 2.0, 3.0
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The value written to L2CSR1 didn't match the value written to the
device tree.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Modify code to adapt to both u-qe and qe.
U_QE is a kind of cutted QE.
the differences between U_QE and QE
1. UCC: U_QE supports 2 UCCs while QE supports up to 8 UCCs.
2. IMMR: have different immr base addr.
3. iopin: U_QE doesn't need to config iopin.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
CONFIG_SYS_QE_FMAN_FW_ADDR is used to both Fman and QE for microcode address.
Now using CONFIG_SYS_FMAN_FW_ADDR for Fman microcode address,
and CONFIG_SYS_QE_FW_ADDR for QE microcode address.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Secure Boot Target is added for T1040QDS and T1040RDB
Changes:
For Secure boot, CPC is configured as SRAM and used as house
keeping area which needs to be disabled.
So CONFIG_SYS_CPC_REINIT_F is defined for CONFIG_T1040QDS and
CONFIG_T1040RDB
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Secure Boot Target is added for T2080QDS
Changes:
For Secure boot, CPC is configured as SRAM and used as house
keeping area which needs to be disabled.
So CONFIG_SYS_CPC_REINIT_F is defined for CONFIG_T2080QDS.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Secure Boot Target is added for T4240QDS and T4160QDS
Changes:
For Secure boot, CPC is configured as SRAM and used as house
keeping area which needs to be disabled.
So CONFIG_SYS_CPC_REINIT_F is defined for CONFIG_T4240QDS.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Changes:
1. L2 cache is being invalidated by Boot ROM code for e6500 core.
So removing the invalidation from start.S
2. Clear the LAW and corresponding configuration for CPC. Boot ROM
code uses it as hosekeeping area.
3. For Secure boot, CPC is configured as SRAM and used as house
keeping area. This configuration is to be disabled once in uboot.
Earlier this disabling of CPC as SRAM was happening in cpu_init_r.
As a result cache invalidation function was getting skipped in
case CPC is configured as SRAM.This was causing random crashes.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add NOR, SPI and SD secure boot targets for BSC9132QDS.
Changes:
- Debug TLB entry is not required for Secure Boot Target.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
ISBC creates a LAW 0 entry for non PBL platforms, which is not
disabled before transferring the control to uboot.
The LAW 0 entry has to be disabled.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For KVM we have a special PV machine type called "ppce500". This machine
is inspired by the MPC8544DS board, but implements a lot less features
than that one.
It also provides more PCI slots and is supposed to be enumerated by
device tree only.
This patch adds support for the generic ppce500 machine and tries to
rely solely on device tree for device enumeration.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
We want to be able to directly execute the ELF binary without going
through the u-boot.bin one.
To know where we have to start executing this ELF binary we have to
tell the linker where our entry point is.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The DDR mapping function really is just a generic virtual -> physical
mapping function. Generalize it so it can support any virtual starting
offset and IO maps just the same.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
There is no need to set IVORs to anything but their default values,
so let's leave them where they are.
Suggested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Scott Wood <scottwood@freescale.com>
[York Sun: Add back $(obj)start.S section in mpc8572ds/Makefile]
Reviewed-by: York Sun <yorksun@freescale.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/mousse/*
- Remove include/configs/MOUSSE.h
- Clean-up defined(CONFIG_MOUSSE)
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since these boards were moved to Orphan. Remove.
- Remove board/RPXlite/*
- Remove board/RPXClassic/*
- Remove include/configs/RPXlite.h
- Remove include/configs/RPXClassic.h
- Clean-up defined(CONFIG_RPXCLASSIC)
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since these boards were moved to Orphan. Remove.
- Remove include/configs/{ADS860.h,FADS823.h,FADS850SAR.h,FADS860T.h}
- Cleanup defined(CONFIG_ADS), defined(CONFIG_MPC823FADS),
defined(CONFIG_MPC850SAR), defined(CONFIG_SYS_DAUGHTERBOARD)
- Remove the entries from boards.cfg
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since these boards were moved to Orphan. Remove.
- Remove board/mbx8xx/*
- Remove include/configs/{MBX.h,MBX860T.h}
- Clean-up if defined(CONFIG_MBX)
- Move the entries from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/nx823/*
- Remove include/configs/NX823.h
- Clean-up ifdef(CONFIG_NX823)
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
References to the wireless keyboard should also be removed
from README.console.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
1. The Data timeout counter value in eSDHC_SYSCTL register is
not working as it should be, so add quirks to enable this
workaround to fix it to the max value 0xE.
2. Add CONFIG_SYS_FSL_ERRATUM_ESDHC111 to enable its workaround.
* Update of patch for change mmc interface by
Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Prior to Kbuild, $(OBJTREE) was used for pointing to the
top of build directory with absolute path.
In Kbuild style, $(objtree) is used instead.
This commit renames OBJTREE to objtree and delete the
defition of OBJTREE.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Prior to Kbuild, $(TOPDIR) or $(SRCTREE) was used for
pointing to the top of source directory.
(No difference between the two.)
In Kbuild style, $(srctree) is used instead.
This commit renames TOPDIR to srctree and delete the
defition of TOPDIR.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Many USB host controller drivers contain almost identical copies of the
same virtual root hub descriptors. Put these into a common file to avoid
duplication.
Note that there were some very minor differences between the descriptors
in the various files, such as:
- USB 1.0 vs. USB 1.1
- Manufacturer/Device ID
- Max packet size
- String content
I assume these aren't relevant.
Cc: Thomas Lange <thomas@corelatus.se>
Cc: Shinya Kuribayashi <skuribay@pobox.com>
Cc: Gary Jennejohn <garyj@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Eric Millbrandt <emillbrandt@coldhaus.com>
Cc: Pierre Aubert <p.aubert@staubli.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Denis Peter <d.peter@mpl.ch>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Zhang Wei <wei.zhang@freescale.com>
Cc: Mateusz Zalega <m.zalega@samsung.com>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Markus Klotzbuecher <mk@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Gary Jennejohn <garyj@denx.de>
Cc: C Nauman <cnauman@diagraph.com>
Cc: David Müller <d.mueller@elsoft.ch>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Thomas Abraham <t-abraham@ti.com>
Cc: Tom Rini <trini@ti.com>
Cc: Andrew Murray <amurray@embedded-bits.co.uk>
Cc: Matej Frančeškin <matej.franceskin@comtrade.com>
Cc: Cliff Cai <cliff.cai@analog.com>
Cc: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
T1040 SoC has SCFG (Supplement Configuration) Block which provides
chip specific configuration and status support. The base address of
SCFG block in T1040 is 0xfc000.
SCFG contains SCFG_PIXCLKCR (DIU pixel clock control register)
at offset 0x28.
Add definition of
-SCFG block
-SCFG_PIXCLKCR register
-Bits definition of SCFG_PIXCLK register
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This implements stashing of bootstage timing data to FDT and automatic
timing reporting. To enable define CONFIG_BOOTSTAGE_FDT and
CONFIG_BOOTSTAGE_REPORT respectively.
Signed-off-by: Rommel G Custodio <sessyargc+u-boot@gmail.com>
Reviewed-by: York Sun <yorksun@freescale.com>
USB spec says that the minimum disconnect threshold should be
over 525 mV. However, internal USB PHY threshold value is below
this specified value. Due to this some devices disconnect at
run-time. Hence, phy settings are tweaked to increased disconnect
threshold to be above 525mV by using this workaround.
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SerDes PLLs may not lock reliably at 5 G VCO configuration(A006384)
and at cold temperatures(A006475), workaround recalibrate the
PLLs with some SerDes configuration
Both these errata are only applicable for b4 rev1.
So, make workaround for these errata conditional,
depending upon soc version.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
B4860 has two PLL per SerDes whereas B4420 has one PLL per SerDes,
add their defines in arch/powerpc/include/asm/config_mpc85xx.h
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
On B4860 and B4420, some serdes protocols can be used with LC VCO as
well as Ring VCO options.
Addded Alternate options with LC VCO for such protocols.
For example protocol 0x2a on srds 1 becomes 0x29 if it is LC VCO.
The alternate option has the same functionality as the original option;
the only difference being LC VCO rather than Ring VCO.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1) SerDes2 Refclks have been set properly to make
PCIe SATA to work as it work on SerDes refclk of 100MHz
2) Mask the SerDes's device reset request before changing
the Refclks for SerDes1 and SerDes2 for PLL locks to
happen properly, device reset request bit unmasked
after SerDes refclks configuration
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1) Add new SerDes1 protocols having Aurora in them
2) Add VSC cross point connections for Aurora to work with
CPRI and SGMIIs
3) Configure VSC crossbar switch to connect SerDes1
lanes to aurora on board, by checking SerDes1 protocols
4) SerDes1 Refclks have been set properly to make
Aurora, CPRI and SGMIIs to work together properly
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
"checkgcc4" is used only for PowerPC.
Move it to arch/powerpc/config.mk.
To make sure gcc is new enough before beginning build,
run "checkgcc4" during "archprepare".
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Before this commit, CONFIG_MPC8260 and CONFIG_8260
were used mixed-up.
All boards with mpc8260 cpu defined both of them:
- CONFIG_MPC8260 was defined in board config headers
and include/common.h
- CONFIG_8260 was defined arch/powerpc/cpu/mpc8260/config.mk
We do not need to have both of them.
This commit keeps only CONFIG_MPC8260.
This commit does:
- Delete CONFIG_8260 and CONFIG_MPC8260 definition
in config headers and include/common.h
- Rename CONFIG_8260 to CONFIG_MPC8260
in arch/powerpc/cpu/mpc8260/config.mk.
- Rename #ifdef CONFIG_8260 to #ifdef CONFIG_MPC8260
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
