usdhc4 has eMMC on icore-rqs boards, SPL is not detecting
it becuase of u-boot,dm-spl flag so add it to make eMMC working.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Engicam Is.IoT has eMMC and NAND cpu modules where MMC
is common for both, so remove explicit mmc defconfig.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The UHS modes are not supported in beagle-x15 because it's not possible to
switch the IO lines supply voltage to 1.8v.
Also HS200 cannot be supported on mmc2, because the IO lines of mmc2 are
connected to 3.3v.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Use the new compatible string "ti,dra7-hsmmc" that was specifically
added for dra7 and dra72. This is required since for dra7 and dra72
processors iodelay values has to be set unlike other processors.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Enable I2C6 bus on Porter to access the PMIC , ie. to reset the board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Fix ommission where the u-boot,dm-pre-reloc DT bit was pulled into the
common DT, not the U-Boot specific DT part. Move it to U-Boot DT part.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Those two nodes are needed to configure pinmux before relocation
and to configure clock before relocation, since CPG/MSSR needs
access to RST node. This is not noticable on Gen3, but on Gen2
this causes problems in SPL if they are not available early.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Make the SCIF available before relocation and in SPL on R8A7791 Porter.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch adds "spi-flash" to the compatible list of the qspi flash
chip for all socfpga boards. This is required to make qspi work on
these boards on top of the recent fixes. Without the "spi-flash"
compatible string for the flash chip, the speed cannot be read and a
speed of 0Hz is used (which results in a divide-by-zero on these
boards).
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
The input keycode KEY_POWER is used in the imx6ull.dtsi file,
hence include the input header where used.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
The pinmux and tuning settings are from
https://source.codeaurora.org/external/imx/linux-imx/tree/arch/
arm/boot/dts/imx7s.dtsi?h=imx_4.9.11_1.0.0_ga
https://source.codeaurora.org/external/imx/linux-imx/tree/arch/
arm/boot/dts/imx7d-sdb.dts?h=imx_4.9.11_1.0.0_ga
To support HS200 and SDR104, we need change pinmux settings dynamically.
And configure tuning step and start tuning tap, otherwise you may
see tuning failure.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
i.CoreM6 1.5 is an another i.CoreM6 QDL cpu modules which can be connected
to EDIMM starter kit design with eMMC and MIPI-CSI interfaces suitable for
Android and video capture application.
notable features:
CPU NXP i.MX6 S/DL/D/Q, Up to 4 x Cortex-A9@800MHz
Memory Up to 2 GB DDR3-1066
Video Interfaces Up to 1 Parallel Up to 2 LVDS HDMI 1.4
port 8 bit CSI INPUT MIPI-CSI INPUT
1 x 10/100 Ethernet interface, 2 x USB, 1 x PCIe, 1 x I2S etc
This patch adds support for Quad/Dual and DualLite/Solo SOM's on
MIPI starter kit with boot from SD and eMMC.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlpxesoACgkQykllyylKDCFwngCfZfk2S+c9uJCLh1drA7a+J4Ch
G+MAnA/iRu6/Ihd5UMe4tMK8BU51h0GQ
=Ylul
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.03' of git://git.denx.de/u-boot-microblaze
Xilinx changes for v2018.03
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
This patch adds new target which is called as mini configuration
with only emmc functionality and other required basic features enabled.
This will be used to run in system with small footprint and needs
emmc support.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new target which is called as mini configuration
with only nand functionality and other required basic features enabled.
This will be used to run in system with small footprint and needs
nand support.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Drop the space before/after '<' and '>'; and
separate the entries to be a bit more readable.
Reported-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
zc770-xm011 is x8 width configuration. This FMC card has also x16
variant which requires different ps7_init configuration. This patch adds
it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The serial drivers now depend on the pinctrl driver to determine whether
they are enabled. That means if a serial device wants to be used pre-reloc,
we also need the pinctrl device pre-reloc.
Adapt the pinctrl driver as well as dts overlay accordingly.
Signed-off-by: Alexander Graf <agraf@suse.de>
The backlight pwm-cell is 3.
This remove the warning in buildman:
arch/arm/dts/rk3126-evb.dtb: Warning (pwms_property): Property 'pwms', cell 3 is not a phandle reference in /backlight
arch/arm/dts/rk3126-evb.dtb: Warning (pwms_property): Missing property '#pwm-cells' in node /sram@10080400 or bad phandle (referred from /backlight:pwms[3])
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The LCDC assigned rate is 0, it will make boot error,
error log:"pll_para_config: the frequency can not be
0 Hz". Remove them, and the lcdc driver will do the
correct clock rate setting.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add basic dts configuration for rk3328 gmac2io.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Give the mac controller the correct tx-delay and rx-delay value
for the rgmii mode transmission. If they are not matched, there
would be Ethernet packets lost, the net feature may not work.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This DT file comes from kernel v4.15, this board offers :
_ STM32F429NIH6 microcontroller
_ 4.3” color TFT LCD with resistive touchscreen (480 x 272 pixels)
_ Six 5 V power supply options:
Power jack
ST-LINK/V2 USB connector
User USB HS connector
User USB FS1 connector
User USB FS2 connector
Daughterboard
_ SAI Audio DAC, stereo audio jack which supports headset with
microphone
_ Stereo digital microphone, audio terminal connector used to connect
external speakers
_ 2 GBytes (or more) SDIO interface MicroSD card
_ RF EEPROM on I2 C compatible serial interface
_ RS-232 communication
_ IrDA transceiver
_ JTAG/SWD and ETM trace debug support, ST-LINK/V2 embedded
_ IEEE-802.3-2002 compliant Ethernet connector
_ Camera module
_ 8M x 32-bit SDRAM, 1M x 16-bit SRAM and 8M x 16-bit NOR Flash
_ Joystick with 4-directional control and selector
_ Reset, Wakeup and Tamper buttons
_ 4 color user LEDs
_ Extension connectors & memory connectors for daughterboard or
wrapping board
_ USB OTG HS and FS with Micro-AB connectors
_ RTC with backup battery
_ CAN2.0A/B compliant connection
_ Potentiometer
_ Motor control connector
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In order to retrieve the clk_hse fixed clock phandle in clk_stm32f driver,
add "u-boot,dm-pre-reloc" property in Uboot specific DT file.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add U-Boot DT extras for each SoC and board. This marks the required
nodes with u-boot,dm-pre-reloc to start clock and PRR early on while
avoiding modification of the DTs imported from Linux.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The Stout board is not supported in Linux, so add a rudimentary DTS
for H2 Stout as a placeholder for when a proper DTS is available.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: The Stout is already being shipped over, so proper DTS for both
U-Boot and Linux will happen once it's delivered :-)
Import the Renesas R8A7794 DTS and headers from upstream Linux kernel v4.15-rc8,
commit bebc6082da0a9f5d47a1ea2edc099bf671058bd4 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Import the Renesas R8A7793 DTS and headers from upstream Linux kernel v4.15-rc8,
commit bebc6082da0a9f5d47a1ea2edc099bf671058bd4 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Import the Renesas R8A7792 DTS and headers from upstream Linux kernel v4.15-rc8,
commit bebc6082da0a9f5d47a1ea2edc099bf671058bd4 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Import the Renesas R8A7791 DTS and headers from upstream Linux kernel v4.15-rc8,
commit bebc6082da0a9f5d47a1ea2edc099bf671058bd4 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Import the Renesas R8A7790 DTS and headers from upstream Linux kernel v4.15-rc8,
commit bebc6082da0a9f5d47a1ea2edc099bf671058bd4 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Pull out u-boot extras into dtsi files to make synchronization of DTS
from Linux kernel as easy as a simple copy. All the U-Boot extras are
now in *-u-boot.dts* files instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Import the RCar Gen3 DTS and headers from upstream Linux kernel v4.14,
commit bebc6082da0a9f5d47a1ea2edc099bf671058bd4 . This includes both M3
and H3 ULCB and Salvator-X boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Adopt the Linux DT bindings and clean-up duplicate
and unused values.
Fix indentation of the QSPI node in the keystone k2g
device tree.
Tested on TI K2G platform:
Tested-by: Vignesh R <vigneshr@ti.com>
Tested on a socfpga-cyclonev board:
Tested-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Signed-off-by: Jason Rush <jarush@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Acked-by: Marek Vasut <marex@denx.de>
The current GPL only licensing on the device trees makes it very
impractical for other software components licensed under another
license.
To make it easier to reuse them, re-license the the device trees for
Freescale (now NXP) SoCs and boards under GPLv2+/X11 dual license.
Same trend is followed in linux.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This commit adds OMAP3 BeagleBoard devicetree files from
Linux v4.15-rc5. This includes standard OMAP34XX board revisions as
well as the 'xM' which is OMAP36XX.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
If lk lights up display and populates simple-framebuffer node, it will
also setup a reserved-memory node (needed by simplefb on linux). But
it isn't clever enough to cope when the reserved-memory node is not
present.
Signed-off-by: Rob Clark <robdclark@gmail.com>
The firmware that runs before u-boot modifies u-boot's device tree
adding the local-mac-address and local-bd-address properties for the
compatibles "qcom,wcnss-bt" and "qcom,wcnss-wlan".
This commit reads that firmware, retrieves the properties and fixups
the device tree that is passed to the kernel before booting.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
This commit adds support for 96Boards Dragonboard820C.
The board is based on APQ8086 Qualcomm Soc, complying with the
96Boards specification.
Features
- 4x Kyro CPU (64 bit) up to 2.15GHz
- USB2.0
- USB3.0
- ISP
- Qualcomm Hexagon DSP
- SD 3.0 (UHS-I)
- UFS 2.0
- Qualcomm Adreno 530 GPU
- GPS
- BT 4.2
- Wi-Fi 2.4GHz, 5GHz (802.11ac)
- PCIe 2.0
- MIPI-CSI, MIPI-DSI
- I2S
U-Boot boots chained from LK (LK implements the fastboot protocol) in
64-bit mode.
For detailed build instructions see readme.txt in the board directory.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
LS1012A-2G5RDB belongs to LS1012A family with features 2 2.5G SGMII
PFE MAC, SATA, USB 2.0/3.0, WiFi DDR, eMMC, QuadSPI, UART.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
64-bit Tegra don't use SPL, and soon won't define CONFIG_SPL_TEXT_BASE
when building. Fix the binman .dts file so that it doesn't use undefined
values.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
To support QSPI DM driver
- Add spi0 alias for qspi node. Which is used for bus number 0.
- Modify the n25q256a@0 compatible property to "spi-flash".
- Modify spi4 (gpio_spi) node to spi5
- Define DM SPI/QSPI related config to enable QSPI
Signed-off-by: Peng Fan <peng.fan@nxp.com>
BCM2835 ARM Peripherals doc shows gpio pins 4, 5, 6, 12 and 13 carry altenate
function, ALT5 for ARM JTAG
Signed-off-by: Henry Zhang <henryzhang62@yahoo.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add DT nodes to enable ARM_PL180_MMCI IP support for STM32F746
and STM32F769 discovery boards
There is a hardware issue on these boards, it misses a pullup on the GPIO line
used as card detect to allow correct SD card detection.
As workaround, cd-gpios property is not present in DT.
So SD card is always considered present in the slot.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This DT file comes from kernel v4.15-rc1
stm32f469-pinctrl.dtsi header has been updated with correct
STMicroelectronics Copyright.
Remove the paragraph about writing to the Free Software
Foundation's mailing address as requested by checkpatch.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
_ Add gpio compatible and aliases for stm32f429
_ Add FMC sdram node with associated new bindings value to
manage second bank (ie bank 1).
_ Add "u-boot,dm-pre-reloc" for rcc, fmc, fixed-clock, pinctrl,
pwrcfg and gpio nodes.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
All these files comes from kernel v4.15-rc1.
Update some header with correct STMicroelectronics Copyright.
Remove the paragraph about writing to the Free Software
Foundation's mailing address as requested by checkpatch.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The DB-88F6820-AMC connects ethernet@34000 and ethernet@70000 which are
labeled as eth2 and eth0 in armada-38x.dts. The ethernet@30000 (eth1) is
not used on the AMC board.
This eliminates the following bootup message
Device 'ethernet@70000': seq 0 is in use by 'ethernet@34000'
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Commit 8620f38409 ("dm: sunxi: Linksprite_pcDuino3: Correct polarity
of MMC card detect") claims that the Pcduino3 device tree had an
incorrect polarity for the card detect pin and thus changed the polarity
flag of the cd-gpios from GPIO_ACTIVE_HIGH to GPIO_ACTIVE_LOW.
Actually the DT was correct since according to the mmc binding, a
combination of GPIO_ACTIVE_HIGH + cd-inverted results in an active-low
polarity. But because the U-Boot driver lacks the code to look at the
cd-inverted property (unlike the Linux driver) it interpreted the
polarity of active-high. Thus, after that commit the DT is actually
wrong from the binding/Linux point of view.
To make both Linux and U-Boot interpret the DT in the same way, just
drop the left-over cd-inverted property. I've sent a Linux patch to
switch all sunxi DTs over to not using the cd-inverted property, so
eventually all sunxi boards in U-Boot will be consistent in not using
cd-inverted.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The Libre Computer Board ALL-H3-CC from Libre Technology is a Raspberry
Pi B+ form factor single board computer based on the Allwinner H3 SoC.
The board has 1GB DDR3 SDRAM, provided by 4 2Gb chips. The mounting holes
and connectors are in the exact same position as on the Raspberry Pi B+.
Raspberry Pi B+ like peripherals supported on this board include:
- Power input through micro-USB connector (without USB OTG)
- Native 100 Mbps ethernet using the internal PHY, as opposed to
USB-based on the RPi
- 4x USB 2.0 host ports, directly connected to the SoC, as opposed to
being connected through a USB 2.0 hub on the RPi
- TV and audio output on a 3.5mm TRRS jack
- HDMI output
- Micro-SD card slot
- Standard RPi B+ GPIO header, with the standard peripherals routed to
the same pins.
* 5V, 3.3V power, and ground
* I2C0 on the H3 is routed to I2C1 pins on the RPi header
* I2C1 on the H3 is routed to I2C0 pins on the RPi header
* UART1 on the H3 is routed to UART0 pins on the RPi header
* SPI0 on the H3 is routed to SPI0 pins on the RPi header,
with GPIO pin PA17 replacing the missing Chip Select 1
* I2S1 on the H3 is routed to PCM pins on the RPi header
- Additional peripherals from the H3 are available on different pins.
These include I2S0, JTAG, PWM1, SPDIF, SPI1, and UART3
In addition, there are a number of new features:
- Console UART header
- Consumer IR receiver
- Camera interface (not compatible with RPi)
- Onboard microphone
- eMMC expansion module port
- Heatsink mounting holes
This patch adds defconfig and dts files for this board. The dts file is
the same as the one submitted for inclusion in Linux, with some minor
revisions to match the dtsi file and old EMAC bindings in U-boot.
Since the OTG controller is wired to a USB host port, and the H3 has
proper USB hosts to handle host mode, the MUSB driver is not enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Without this propertiy, U-Boot will pop warning of 'USB phy type not
defined' when select CONFIG_HAS_FSL_DR_USB.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
This commit adds OMAP3 EVM devicetree files from Linux v4.15-rc3. Note
that this is the first addition of OMAP34XX devicetree files.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Enable sdmmc node in SPL and add it to boot order.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Fixed commit tags:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Since commit 999a78d5cf ("scripts/dtc: Update to upstream version v1.4.5-3-gb1a60033c110")
dtc warns about:
arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@50000000/serial@53fc0000
arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@50000000/ccm@53fd4000
arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@50000000/gpio@53fe4000
arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@60000000/sdma@63fb0000
arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@60000000/ethernet@63fec000
Fix this by adding a node for the tzic interrupt controller.
Copied from "<Linux>/arch/arm/boot/dts/imx53.dts"
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Commit 5248930ebf ("dm: imx: cm_fx6: Enable more driver model support")
enabled driver model support for USB, thereby effectively removing USB
support because the cm_fx6 devicetree in the U-Boot does *not* enable the
USB nodes.
Reinstate the USB support by syncing the devicetree with Linux whose
devicetree enables the USB nodes properly.
More precisely, use the devicetree found in Linux v4.15-rc1 with the
following two changes:
1) Remove the audio mux; the required dt-bindings header is not
present in the U-Boot.
2) Keep the usdhc3 MMC controller node currently present in the
U-Boot's devicetree to retain the ability to boot from MMC.
Fixes: 5248930ebf ("dm: imx: cm_fx6: Enable more driver model support")
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Order sun50i-h5-orangepi-prime.dts nodes in alphabetic
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
fpga:
- Enable loading bitstream via fit image for !xilinx platforms
zynq:
- Fix SPL SD boot mode
zynqmp:
- Not not reset in panic
- Do not use simple allocator because of fat changes
- Various dt chagnes
- modeboot variable setup
- Fix fpga loading on automotive devices
- Fix coverity issues
test:
- Fix env test for !hush case - Stephen's patch
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlo3tMgACgkQykllyylKDCFQvQCfeFgaC/95gx9orLrHxpDx7s46
wwYAmwSoXn6hc9bEzgKIppQHblzfqGU6
=mscK
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.01-rc2-v2' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2018.01-rc2-v2
fpga:
- Enable loading bitstream via fit image for !xilinx platforms
zynq:
- Fix SPL SD boot mode
zynqmp:
- Not not reset in panic
- Do not use simple allocator because of fat changes
- Various dt chagnes
- modeboot variable setup
- Fix fpga loading on automotive devices
- Fix coverity issues
test:
- Fix env test for !hush case - Stephen's patch
This is the same patch as was done earlier.
Please look at Linux patch:
"arm64: zynqmp: Use only earlycon bootargs instead of full one"
(sha1: f3609c8d4af28b9cc22ca49bf8e529b582ec188c)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove overfetch, ratectrl, include-sg and src-issue dma properties.
Driver is not using them and they are also not documented in the binding
doc.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Kedareswara rao Appana <appanad@xilinx.com>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is enabling support for SPL QSPI boot.
First of all it is necessary to generate atf-spi.ub which is different
format than atf-uboot.ub (this can be made as legacy image too)
ADDR=`arm-xilinx-linux-gnueabi-readelf -a bl31.elf | grep "Entry point
address" | cut -d ':' -f 2 | sed -e 's/^[ \t]*//'`
aarch64-linux-gnu-objcopy -O binary bl31.elf bl31.bin
./tools/mkimage -f auto -A arm64 -T firmware -C none -O u-boot -a $ADDR
-e $ADDR -n "atf1" -E -b arch/arm/dts/zynqmp-zcu102.dtb -d bl31.bin
atf-uboot.ub
./tools/mkimage -A arm64 -T firmware -C none -O u-boot -a $ADDR -e $ADDR
-n "atf-for-qspi" -E -d bl31.bin atf-spi.ub
This patch is using this QSPI layout with offsets:
0 boot.bin
512k atf-ub
640k u-boot.bin
1280k u-boot.img
Which corresponding by writing these images(read from MMC)
mmcinfo
sf probe
load mmc 0 10000000 boot.bin
sf erase 0 +$filesize
sf write 10000000 0 $filesize
load mmc 0 10000000 atf-spi.ub
sf erase 0x80000 +$filesize
sf write 10000000 0x80000 $filesize
load mmc 0 10000000 u-boot.bin
sf erase 0xa0000 +$filesize
sf write 10000000 0xa0000 $filesize
load mmc 0 10000000 u-boot.img
sf erase 0x140000 +$filesize
sf write 10000000 0x140000 $filesize
For testing u-boot running in EL3 you can break atf-spi.ub like this:
sf probe
sf erase 0x80000 +4
Then u-boot.img is executed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This reference is needed for pinctrl driver where some signals can be
routed directly to platform management unit (PMU).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Update tegra to use binman for image creation. This still includes the
current Makefile logic, but a later patch will remove this. Three output
files are created, all of which combine
SPL and U-Boot:
u-boot-tegra.bin - standard image
u-boot-dtb-tegra.bin - same as u-boot-tegra.bin
u-boot-nodtb-target.bin - includes U-Boot without the appended device tree
The latter is useful for build systems where the device is appended later,
perhaps after being modified.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add bits to support yet another board, the R8A77995 D3 Draak.
The DT file is from Linux 4.15-rc1 , commit
b35334447513c14a4dd55a67c269a743d4a4824b .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add bits to support yet another board, the R8A77970 V3M Eagle.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add bits to support yet another SoC, the R8A77995 D3 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add bits to support yet another SoC, the R8A77970 V3M .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
