On the sandbox the UEFI binaries must match the host architectures.
Adjust the Makefiles. Provide the PE/COFF header and relocation files.
Allow building helloworld.efi on the sandbox.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add support for USB3 host and gadget driver. This is a direct sync of
Linux kernel Cadence USB stack that from v5.4-rc1 release.
Driver has been modified so that it compiles without errors against
U-Boot code base.
Features not required for U-Boot such as scatter-gather DMA and OTG
interrupt handling has been dropped.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
[jjhiblot@ti.com: Add PHY support]
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
imx targets are defined in arch/arm/mach-imx/Makefile.
Some of them are dependent on targets defined in main
Makefile. For the Makefile in arch/arm/mach-imx this
targets must be finished before the imx targets are
build, if not you get for example the error:
make -f /home/hs/abb/mainlining/u-boot/scripts/Makefile.build obj=arch/arm/mach-imx u-boot-dtb.imx
make[2]: *** No rule to make target 'u-boot-fit-dtb.bin', needed by 'u-boot-dtb.imx'. Stop.
make[1]: *** [/home/hs/abb/mainlining/u-boot/Makefile:1123: u-boot-dtb.imx] Error 2
make[1]: *** Waiting for unfinished jobs....
make[1]: Leaving directory '/work/hs/compile/u-boot/aristainetos2_defconfig'
make: *** [Makefile:148: sub-make] Error 2
compile failed
In above case of CONFIG_MULTI_DTB_FIT is defined, the
u-boot-dtb.imx is dependent on the u-boot-fit-dtb.bin
which may is not build yet ...
I could reproduce this error on a travis build also if
I build an out-of-tree build on a local machine with a
build directory on a "slow" slow storage device. If
building the same source target with a build dir on a
fast storage device, the build works.
I found no solution to tell the arch/arm/mach-imx/Makefile
to find the targets in main Makefile, if there is a way
this would be the better fix.
I solved it by adding a IMX_DEPS var, which holds a list
of main u-boot targets, which must be finished, before
calling imx targets and fixed the build for imx
targets which enabled CONFIG_MULTI_DTB_FIT.
I think it is just luck, that imx targets with
CONFIG_OF_SEPARATE enabled build, because the
u-boot-dtb.imx target depends on u-boot-dtb.bin
which gets build early enough before starting with
u-boot-dtb.imx. May this targets should be fixed too.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
We have the ability to enforce a maximum size for SPL but not yet for TPL.
Add a new option for this.
Document the size check macro while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When we have an excess size growth, fix the "limit" printf call to pass
in just the limit variable rather than the string bytes to the format
character.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
At present some boards generate kwbimage.cfg in the source tree
during the build. This breaks buildman testing on some systems
where the source tree is read-only. Update makefile rules to
generate it in the build tree instead.
Note some other boards have the kwbimage.cfg file written in
advance, hence we need check if the file exists in the build
tree first, otherwise we fall back to one in the source tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
When building U-Boot host tools for Windows from Microsoft Azure
Pipelines, the following errors were seen:
HOSTCC tools/mkenvimage.o
In file included from tools/mkenvimage.c:25:
./tools/version.h:1:1: error: expected identifier or ‘(’ before ‘.’ token
1 | ../include/version.h
| ^
tools/mkenvimage.c: In function ‘main’:
tools/mkenvimage.c:117:4: warning: implicit declaration of function ‘usage’ [-Wimplicit-function-declaration]
117 | usage(prg);
| ^~~~~
tools/mkenvimage.c:120:35: error: ‘PLAIN_VERSION’ undeclared (first use in this function)
120 | printf("%s version %s\n", prg, PLAIN_VERSION);
| ^~~~~~~~~~~~~
tools/mkenvimage.c:120:35: note: each undeclared identifier is reported only once for each function it appears in
make[2]: *** [scripts/Makefile.host:114: tools/mkenvimage.o] Error 1
It turns out tools/version.h is a symbolic link and with Windows
default settings it is unsupported hence the actual content of
tools/version.h is not what file include/version.h has, but the
the linked file path, which breaks the build.
To fix this, remove the symbolic links for tools/version.h. Instead
we perform a copy from include/version.h during the build.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
- Dropping some test Elf files and building them from source instead
- Refactoring of x86 16-bit entries
- Support for SPL symbols within sections
- Handle the 'notes' sections and hidden symbols in recent binutils
- Improved error reporting with a tool fails
libfdt and documentation fixes
vboot required-key test
driver model power-domain controls
patman Message-Id enhancement
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl2l20YACgkQfxc6PpAI
reZQQQgA0zxySnZR6IuTr+MXJP019SjU0T/rj2Ob77ODhLTtLtE3aFYgBIsyyOyr
/NZ6V7wPhCfGGBGWdPzYdOUIkG5L4O+1zrwWGgVJCAAaCaDlJVIXmljJ667SE9ps
9jfJW/nkzgsa/cOweOUJF3vBUKnDN1pv9aTXwAXttzv/OqaZ1AaUObnmeZ9fzr65
mXjR7/eLYx26KQ8IEo8hhgdFhN/d/aUtSCYPWASqtcI9TLg8A5gmtNxy83+w8gzC
kFIr7c0QjZ3EQHLyD4/MAcGvhZZMBPbV6dyIO19hUS80S1l1yMTd72iTYuvG8bAt
5TzlQCSqvGryF6TRxVn8GPr2/T0v/A==
=Oo/D
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-15oct19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
binman enhancements:
- Dropping some test Elf files and building them from source instead
- Refactoring of x86 16-bit entries
- Support for SPL symbols within sections
- Handle the 'notes' sections and hidden symbols in recent binutils
- Improved error reporting with a tool fails
libfdt and documentation fixes
vboot required-key test
driver model power-domain controls
patman Message-Id enhancement
cscope complains that it can't find files that appears to be symbolic links
cscope: cannot find file tools/binman/test/u_boot_binman_syms_bad.c
cscope: cannot find file tools/version.h
`find -L` tests properties, but name, and cscope can't cope with symbolic
links (a lot of bugs in upstream were simple closed as kinda invalid).
To work around the problem, exclude symbolic links from the cscope.files.
Note, it's done in two pass to speed up the process (`-exec realpath ...`
approach is not portable and introduces a 3x delay).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
At present these two sections of code are linked together into a single
2KB chunk in a single file. Some Intel SoCs like to have a FIT (Firmware
Interface Table) in the ROM and the pointer for this needs to go at
0xffffffc0 which is in the middle of these two sections.
Make use of the new 'reset' entry and change the existing 16-bit entry to
include just the 16-bit data.
Signed-off-by: Simon Glass <sjg@chromium.org>
When building a FIT image for SPL to load also take into account the
configured external offset. This allows the SPL to load the u-boot FIT
image correctly when configuring SECURE_BOOT on i.mx6 is enabled
(with CONFIG_FIT_EXTERNAL_OFFSET=0x3000).
Note this doesn't allow secure booting; but it does allow an unsigned
SPL/u-boot with secure boot support eanbled to boot on open device.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
CONFIG_SECURE_BOOT is too generic and forbids to use it for cross
architecture purposes. If Secure Boot is required for imx, this means to
enable and use the HAB processor in the soc.
Signed-off-by: Stefano Babic <sbabic@denx.de>
To support SPL loading container file, add a new Makefile target,
and introduce a new Kconfig file to source the cfg file which
will be parsed by mkimage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This is currently a decimal value which is not as convenient or
meaningful. Also U-Boot tends to use hex everywhere.
Convert this option to hex and add a comment for the size_check macro.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct the typo in the commit title]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Support a new BINMAN_VERBOSE option to the build, to allow passing the
-v flag to binman.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Pass in the toolpath in case binman needs to use tools compiled in the
U-Boot tools/ directory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
*.pyc files contain compiled Python bytecode. 'make mrproper' should remove
them.
Removing *.pyc files helps for instance sometimes when running into an
error "binman: Unknown entry type 'blob' in node '/binman/blob'".
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
For many sub-systems we already require the driver model to be used. Yet
there is still a handful of boards that do not have CONFIG_DM enabled.
We should make CONFIG_DM compulsory with release v2020.01
Conversion dates for CONFIG_DM_SPL and CONFIG_DM_TPL are yet to be defined.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Many Rockchip platforms require the same u-boot deploy procedure
when TPL and SPL both enabled.
The following examples are taken from doc/README.rockchip
and board/theobroma-systems/lion_rk3368/README:
RK3288:
./tools/mkimage -n rk3288 -T rksd -d ./tpl/u-boot-tpl.bin out
cat ./spl/u-boot-spl-dtb.bin >> out
sudo dd if=out of=/dev/mmcblk0 seek=64
RK3328:
./tools/mkimage -n rk3328 -T rksd -d ./tpl/u-boot-tpl.bin idbloader.img
cat ./spl/u-boot-spl.bin >> idbloader.img
sudo dd if=idbloader.img of=/dev/mmcblk0 seek=64
RK3368:
./tools/mkimage -n rk3368 -T rksd -d tpl/u-boot-tpl.bin spl-3368.img
cat spl/u-boot-spl-dtb.bin >> spl-3368.img
dd if=spl-3368.img of=/dev/sdb seek=64
RK3399:
./tools/mkimage -n rk3399 -T rksd -d ./tpl/u-boot-tpl-dtb.bin out
cat ./spl/u-boot-spl-dtb.bin >> out
sudo dd if=out of=/dev/sdc seek=64
Here, we introduce generic idbloader.img target
which is the TPL image followed by the SPL binary.
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The driver model has been supported for network drivers since 2015. It is
time to convert the remaining boards. Set July 2020 as a timeline.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
I wanted this to be compatible with mkenvimage, including the ability
to embed newlines in variables by escaping them. But I failed to check
that it works more than once.
Fixes: f3d8f7dd73 (Allow providing default environment from file)
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
TI AM65x platforms (evm and HS) generate an SPL image
'tispl.bin*' and there is no rule for cleanup.
Added entry for cleanup in clean target.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Support of device tree model for T2080RDB, T4240RDB, T1024RDB,
T1042D4RDB, P1020RDB, P2020RDB, P2041RDB, P3041DS, P4080DS, P5040DS and
MPC8548CDS. Also support of i2c dm model.
The current Makefile always use u-boot.bin to generate
PBL boot image (u-boot.pbl), this patch changes it to
use u-boot-with-dtb.bin to support device tree when
CONFIG_OF_SEPARATE is enabled.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
When building a U-Boot FIT image, the device trees specified by the
board are unconditionally built for inclusion in the FIT image. However,
not all device tree providers, such as CONFIG_OF_PRIOR_STAGE, require a
device tree to be built and bundled with the U-Boot binary. They rely on
other mechanisms to provide the device tree to U-Boot. Compilation on
boards with these device tree providers fails, because they do not
specify a device tree.
Change the makefile rules to conditionally build the device trees if
CONFIG_OF_SEPARATE, CONFIG_OF_EMBED, or CONFIG_OF_HOSTFILE is selected
as device tree provider.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
There are no more users of the compatibility layer for i2c. Remove the
driver and all references to it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Heiko Schocher <hs@denx.de>
There are no more "real" users of CONFIG_DM_I2C_COMPAT and we'll soon
remove it altogether. Stop building it in sandbox mode.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Heiko Schocher <hs@denx.de>
binman only accepts the -D argument early on the command-line, yet the
Makefile currently passes it near the end. This causes the build to fail
if this feature is used. Re-order the command-line to fix this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This class is the new way to handle arguments in Python. Convert binman
over to use it. At the same time, introduce commands so that we can
separate out the different parts of binman functionality.
Signed-off-by: Simon Glass <sjg@chromium.org>
By default, CONFIG_SYS_INIT_SP_BSS_OFFSET was made invisible by not
giving a prompt to it.
The only way to define it is to hard-code an extra entry in SoC/board
Kconfig, like arch/arm/mach-tegra/tegra{186,210}/Kconfig.
Add a prompt to it in order to allow defconfig files to specify the
value of CONFIG_SYS_INIT_SP_BSS_OFFSET.
With this, CONFIG_SYS_INIT_SP_BSS_OFFSET would become always visible.
So, we need a new bool option to turn it off by default.
I move the 'default 524288' to the common place. This value is not too
big, but is big enough to avoid the overwrap of DT in most platforms.
If 512KB is not a suitable choice for your platform, you can change it
from your defconfig or menuconfig etc.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Right now rockchip platform need to copy bl31.elf into u-boot
source directory to make use of building u-boot.itb.
So, add environment variable BL31 like Allwinner SoC so-that the
bl31.elf would available via BL31.
If the builds are not exporting BL31 env, the make_fit_atf.py
explicitly create dummy bl31.elf in u-boot root directory to
satisfy travis builds and it will show the warning on console as
WARNING: BL31 file bl31.elf NOT found, resulting binary is non-functional
WARNING: Please read Building section in doc/README.rockchip
Note, that the dummy bl31 files were created during not exporting
BL31 case would be removed via clean target in Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Rockchip platform has its python script that would generate various
bl31_*bin for creating u-boot.itb file by taking bl31.elf as input.
These bl31_*.bin files are generated in u-boot root directory and
have no rule to clean it up. so add support for it by adding in
command entry of clean target in Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
binman tools for creating single image build will create image.map
at the end, which has information about binman image node details.
current u-boot, is unable to clean this image.map so add a command
entry in clean target in Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Commit ad7061ed74 ("doc: Move device tree bindings documentation to
doc/device-tree-bindings") moved all device tree binding documentation
to doc/device-tree-bindings directory.
The current U-Boot project still have two documentation directories:
- doc/
- Documentation/
Move all documentation and sphinx files to doc directory so all content
can be in a common place.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
We have a warning text for non dm converted spi drivers, but the plan is
to mark all these respective drivers with CONFIG_DEPRECATED.
So, trigger a warning saying that these driver configurations and
associated code will remove in v2019.07 (earlier plan is to remove it
from v2019.04)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
If configured target has deprecated configs enabled, trigger a warning
about this.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[trini: Change from BROKEN to DEPRECATED]
Signed-off-by: Tom Rini <trini@konsulko.com>
in case CONFIG_MULTI_DTB_FIT is set and u-boot-dtb.imx
image is build, currently u-boot-dtb.bin is used for
generating the u-boot-dtb.imx binary, which is wrong, as
it contains only a dtb blob not the fit.blob
Use instead the u-boot-fit-dtb.bin for generating
u-boot-dtb.imx which contains the fit.blob.
Signed-off-by: Heiko Schocher <hs@denx.de>
This adds a size check for SPL that can dynamically check generated
SPL binaries (including devicetree) for a size limit that ensures
this image plus global data, heap and stack fit in initial SRAM.
Since some of these sizes are not available to make, a new host tool
'spl_size_limit' is added that dumps the resulting maximum size for
an SPL binary to stdout. This tool is used in toplevel Makefile to
implement the size check on SPL binaries.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
A new configuration variable CONFIG_SPL_SIZE_LIMIT is introduced to define
the board specific maximum size for the SPL file.
Use Makefile function size_check() to implement the test.
Depending on the size of CONFIG_SPL_SIZE_LIMIT an error like the following
is thrown:
spl/u-boot-spl.bin exceeds file size limit:
limit: 30720 bytes
actual: 33426 bytes
excess: 2706 bytes
make: *** [Makefile:1663: spl/u-boot-spl.bin] Error 1
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We currently have duplicate definitions for BOARD_SIZE_CHECK in Makefile
and arch/arm/mach-imx/Makefile.
Move the board size check from arch/arm/mach-imx/Makefile to Makefile.
Depending on the value of CONFIG_BOARD_SIZE_LIMIT an error like an error
like the following is thrown:
u-boot-dtb.imx exceeds file size limit:
limit: 503696 bytes
actual: 509720 bytes
excess: 6024 bytes
make: *** [Makefile:1051: u-boot-dtb.imx] Error 1
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Carve out function size_check from macro BOARD_SIZE_CHECK. This will allow
us to reuse the function for other file size checks.
Depending on the value of CONFIG_BOARD_SIZE_LIMIT an error like the
following is thrown:
u-boot-dtb.img exceeds file size limit:
limit: 409516 bytes
actual: 444346 bytes
excess: 34830 bytes
make: *** [Makefile:1212: u-boot-dtb.img] Error 1
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Build an SPL which can be started via SCIF download mode on R-Car Gen3
and allows loading and executing U-Boot uImage with the next stage code.
This is also useful for starting e.g. ATF BL2, which inits the hardware
and returns to the U-Boot SPL, which can then load e.g. U-Boot proper.
The H3, M3-W, M3-N SoCs have plenty of SRAM for storing the U-Boot SPL
while the payload, e.g. ATF BL2, executes, so there is no problem here.
However, E3 and D3 have much less SRAM, hence the loader uses a trick
where it copies itself beyond the area used by BL2 and executes from
there. That area is 32kiB large and not enough to hold U-Boot SPL, BSS,
stack and malloc area, so the later two are placed at +0x4000 offset
from start of SRAM, another area not used by ATF BL2. To make things
even more complicated, the SCIF loader cannot load to the upper 32kiB
of the SRAM directly, hence the copying approach.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This is causing unexpected size growth in the normal case and is likely
to have been mis-applied by myself.
This reverts commit 3eaf6dcd93.
Signed-off-by: Tom Rini <trini@konsulko.com>
Prioritize external dtb if its passed via EXT_DTB
than the dtb that was built in the tree. With this
patch it appends the specified external dtb to
the u-boot image.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Support for compressed fit-dtb.blob was added in:
commit 95f4bbd581 ("lib: fdt: Allow LZO and GZIP DT compression in
U-Boot")
When building compressed (lzop, gzip) fit-dtb.blob images, the
compression tool may embed the time or umask in the image.
Work around this by manually setting the time of the source file using
SOURCE_DATE_EPOCH and a hard-coded 0600 umask.
With gzip, this could be accomplished by using -n/--no-name, but lzop
has no current workaround:
https://bugs.debian.org/896520
This is essentially the same fix applied to multi-dtb fit SPL images in:
commit 8664ab7deb ("Set time and umask on multi-dtb fit images to
ensure reproducibile builds.")
Signed-off-by: Vagrant Cascadian <vagrant@reproducible-builds.org>
Support for compressed fit-dtb.blob was added in:
commit 95f4bbd581 ("lib: fdt: Allow LZO and GZIP DT compression in
U-Boot")
Adjust Makefile to also clean compressed blobs.
Signed-off-by: Vagrant Cascadian <vagrant@reproducible-builds.org>
As much of the watchdog system has been migrated to DM now, formalize a
deadline for migration.
Please note that the old CONFIG_HW_WATCHDOG macro should be removed
completely at some point.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
At present we support having 16-bit init be in SPL or U-Boot proper, but
not TPL. Add support for this so that TPL can boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The initial environment is linked to the u-boot binary. Modifying the
environment from User Space with the env tools requires that the tools
are always built together with the bootloader to be sure that they
contain the initial environment in case no environment is stored into
persistent storage or when a board boots with just the default
environment. This makes difficult for distros to provide a general
package to access the environment. A simpler way is if the tools are
generic for all boards and a configuration file is given to provide the
initial environment.
The patch just generates the initial environment by extracting it from
the compiled object. This file can then be used for tools in user space
to initialize the environment.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Prioritize external dtb if its passed via EXT_DTB
than the dtb that was built in the tree. With this
patch it appends the specified external dtb to
the u-boot image.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When checking for boards that are enabling a SATA driver that isn't
converted to DM yet we need to be sure to not also trip over boards that
do set CONFIG_AHCI & CONFIG_BLK by itself, as that is not a bug.
This was detected when converting the Armada XP SATA driver sata_mv.c
to DM with AHCI & BLK support. This warning is still printed without
this patch applied here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add required Kconfig symbols, Makefile bits and macro fixes in a
few places to support LZO and DT compression in U-Boot. This can
save a lot of space with multi-DTB fitImages.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This patch adds the CONFIG_SPL_IMAGE option to select the SPL image that
shall be used to generate the combined SPL + U-Boot image. The default
value is the current value "spl/u-boot-spl.bin".
This patch also sets CONFIG_SPL_IMAGE to "spl/boot.bin" for AT91 targets
which use SPL NAND support (boot from NAND). For these build targets the
combined image "u-boot-with-spl.bin" is now automatically generated and
can be programmed into NAND as one single image (vs. SPL image and U-Boot
as 2 separate images).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
When the SPL has full fitImage support, do not generate fitImage with
external data. The full fitImage code assumes the entire fitImage is
loaded in RAM, and the SPL uses fdt_totalsize() to determine the size
of the whole fitImage, which can not work with external data.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
If `make mrproper` does not delete the generated drivers/video/fonts/*.S
files a following `make tests` fails.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The last parameter is expected to be the imagefile. Since -E is a
flag having the output name before -p will make mkimage ignore the
external offset option.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
With the current Makefile, CONFIG_BOARD_SIZE_LIMIT is used to check
the U-Boot binary without devicetree only. This produces wrong results
when OF_SEPARATE is used.
To fix this, run the CONFIG_BOARD_SIZE_LIMIT check on all .img binaries
as well.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Multiple people have reported intermittent build failure in parallel
building.
Kever Yang reported this issue some time ago [1], but I could not
get enough clue at that time.
This time, Richard Purdie provided a full build log [2], which was
very helpful for me to root-cause it.
The cause of the problem is commit 0d982c5853 ("Makefile: add
dependencies to regenerate u-boot.cfg when lost").
That commit added the 'cfg' as the prerequisite of the 'all' target,
so the parallel build tries to run it simultaneously, then regenerates
a symlink while building objects.
When u-boot.cfg is accidentally lost, let's rebuild it before
descending into any subdirectories.
Also, what is annoying is u-boot.cfg is currently regenerated every
time since it depends on FORCE. We can get rid of all the prerequisites
of u-boot.cfg because u-boot.cfg is rebuilt anyway as the byproduct of
auto.conf when a user updates the .config file.
[1] https://lists.denx.de/pipermail/u-boot/2018-June/330341.html
[2] https://autobuilder.yoctoproject.org/typhoon/#/builders/65/builds/160/steps/7/logs/step1b
Fixes: 0d982c5853 ("Makefile: add dependencies to regenerate u-boot.cfg when lost")
Reported-by: Kever Yang <kever.yang@rock-chips.com>
Reported-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is no need to compile and include this code if it is not used.
CONFIG_USB_GADGET can be used for the purpose.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The mkimage_fit_atf.sh SPL FIT generator script requires
u-boot-nodtb.bin, but this was not enforced by the Makefile. This could
cause the generator script to be executed before u-boot-nodtb.bin has
been created.
Signed-off-by: Chris Spencer <christopher.spencer@sea.co.uk>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
When checking for boards that are enabling a SATA driver that isn't
converted to DM yet we need to be sure to not also trip over boards that
do set CONFIG_DM_SCSI by itself, as that is not a bug.
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Fixes: ea9d7c17fc ("dm: MIGRATION: Add migration plan for CONFIG_SATA")
Signed-off-by: Tom Rini <trini@konsulko.com>
- v2019.04 for no dm conversion drivers
- v2019.07 for partially converted drivers.
Note: there were many updates on this deadline, so better
not update this again.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Build flash.bin for i.MX8MQ, it will include signed hdmi firmware,
spl, ddr firmware, fit image(bl31.bin, u-boot-nodtb.bin, dtb).
Burn it to 33KB offset of SD card.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Output the device model migration warnings to stderr. This allows tools
like buildman to pick them up rather than suppressing them along with
the normal build output on stdout.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
The contents of the test subdirectories only make sense when we have
CONFIG_UNIT_TEST set. We will otherwise attempt to build code on for
example sandbox that needs CONFIG_UNIT_TEST otherwise and rather than
complicate the Makefiles simply leave them out when we can.
Signed-off-by: Tom Rini <trini@konsulko.com>
Building U-Boot with CONFIG_PCI and CONFIG_DM_PCI enabled, but
CONFIG_SPL_PCI_SUPPORT disabled, results in following linker
error:
lib/built-in.o: In function `fdtdec_get_pci_bar32':
lib/fdtdec.c:305: undefined reference to `dm_pci_read_bar32'
fdtdec.c:305:(.text.fdtdec_get_pci_bar32+0x24): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `dm_pci_read_bar32'
This is because reference to dm_pci_read_bar32() remains in lib/fdtdec.c
while SPL build does not descend into drivers/pci directory in
drivers/Makefile if CONFIG_SPL_PCI_SUPPORT is not enabled.
Fix this by applying appropriate #define guards in lib/fdtdec.c.
It looks like ns16550.c has the same problem, so fixed that too.
To simplify this, CONFIG_SPL_PCI_SUPPORT is renamed to CONFIG_SPL_PCI
(enables use of CONFIG_IS_ENABLED() macro).
Suggested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
As the core of the subsystem has been converted along with some of the
drivers, formalize a deadline for migration.
Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
Cc: Ludwig Zenz <lzenz@dh-electronics.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Soeren Moch <smoch@web.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
As much of the USB system has been migrated to DM now, formalize a
deadline for migration.
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Given that at this point the MMC subsystem itself has been migrated
along with a number of subsystem drivers, formalize a deadline for
migration.
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
At present tests are quite slow to run, over a minute on my machine. This
presents a considerable barrier to bisecting for failures.
The slowest tests are the filesystem ones and the buildman --fetch-arch
test. Add a new 'qcheck' target that skips these tests. This reduces test
time down to about 40 second, still too long, but bearable.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch adds support for MTK boot image generation.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When the build fails due to something wrong in binman it is sometimes
useful to get a full backtrace showing the location of the failure. Add
a BINMAN_DEBUG environment variable to support this along with some
documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
To prevent accidental build failures the change converts a number of
NXP LPC32xx specific image targets to be conditionally dependent on
target build configuration. The wrapped image targets always contain
a U-Boot SPL binary and the images are supposed to be directly flashed
on a NAND flash device for read access by LPC32xx NAND MLC controller.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
At present // in a device-tree file or link script causes a warning. But
this is used in the standard license header. Update the compiler flags to
use C99, which permits this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we use 'make tests' to run the tests. For many projects
'make check' is more common, so support that as well. Also add some help
to 'make help'.
Signed-off-by: Simon Glass <sjg@chromium.org>
u-boot.itb depends on u-boot-nodtb.bin, which in turn depends on u-boot.
u-boot.its from Rockchip make_fit_atf.py (used by {evb,firefly}-rk3399)
wants to read u-boot but is lacking this dependency, so that u-boot.itb
cannot be built in one go. Detect its use and add the missing dependency.
Reported-by: Yousaf Kaukab <yousaf.kaukab@suse.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This is the PR for SPI-NAND changes along with few spi changes.
[trini: Re-sync changes for ls1012afrwy_qspi*_defconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
Below is the sequence to embed dtb inside U-Boot,
1. Remove bootpg and resetvec section if needed
2. Append dtb
3. Append bootpg and resetvec section back if removed in step 1
Above procedure is required only when CONFIG_MPC85xx and
CONFIG_OF_SEPARATE are defined.
Add new config CONFIG_MPC85XX_HAVE_RESET_VECTOR to indicate that
image has resetvec section. Step 1 and step 3 described above are
required only if this config is y.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
The -fstrict-aliasing option is implicitly enabled at levels -O2,
-O3, -Os by GCC. This option allows the compiler to assume the
strictest aliasing rules applicable to the language being compiled.
For example, the practice of reading from a different union member
than the one most recently written to (called "type-punning") is
common. In this case, "type-punning" only works if the memory is
accessed through the union type, but might not work by taking the
address, casting the resulting pointer and dereferencing the result,
which is an undefined behavior per the "strict aliasing rules".
GCC's -Wstrict-aliasing (included in -Wall) option does not catch
all cases, but does attempt to catch the more common pitfalls. So
there are cases that GCC does not report but the codes are violating
the "strict aliasing rules".
Given lots of codes that may be written to rely on "type-punning",
and Linux kernel disables it by -fno-strict-aliasing globally, since
U-Boot currently does this on nds32/riscv/x86 builds only, extend
this for all architecture builds.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
NAND flavors, like serial and parallel, have a lot in common and would
benefit to share code. Let's move raw (parallel) NAND specific code in a
raw/ subdirectory, to ease the addition of a core file in nand/ and the
introduction of a spi/ subdirectory specific to SPI NANDs.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some devices, namely Intel's stratix10 SoC, require u-boot-spl in
a hex format. This patch adds spl/u-boot-spl.hex as a possible
target.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Since gcc-8 the --enable-default-pie starts producing code which assembler
can't translate in case of U-Boot. The build fails with
{standard input}: Assembler messages:
{standard input}:21100: Error: junk at end of line, first unrecognized character is `@'
{standard input}:21120: Error: junk at end of line, first unrecognized character is `@'
and so on.
This is usually the case for x86 platform because in many cases it uses host
compiler from the Linux distributions, where PIE is enabled by default.
Previously (gcc-7 and earlier) that was a potential issue due to absence of
constructions like
.long end.5561@gotoff-start.5558@gotoff
which are a cause of above error messages in gcc-8.
Fix all these by disabling PIE on Makefile level.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Use GNU make pattern rules to indicate that a single run of binman
produces all three Tegra output files. The avoids make running binman
three times (perhaps in parallel) and those instances inteferring with
each other.
See http://patchwork.ozlabs.org/patch/944611/ for the bug report.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Some legacy boards use RAW image for SPL boot. Add Kconfig option
SPL_PAYLOAD to set alternative image.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that we have removed the DocBook files we need to not try and clean
that directory.
Reported-by: ericywl <midnight2903@gmail.com>
Reported-by: Jagan Teki <jagan@amarulasolutions.com>
Fixes: 78a88f7930 ("doc: Replace DocBook with sphinx-based docs")
Signed-off-by: Tom Rini <trini@konsulko.com>
The Linux kernel moved to sphinx-based documentation and got rid of the
DocBook based documentation quite a while ago. Hence, the DocBook
documentation for U-Boot should be converted as well.
To achieve this, import the necessary files from Linux v4.17, and
convert the current DocBook documentation (three files altogether) to
sphinx/reStructuredText.
For now, all old DocBook documentation was merged into a single
handbook, tentatively named "U-Boot Hacker Manual".
For some source files, the documentation style was changed to comply
with kernel-doc; no functional changes were applied.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Since commit f916757300 (imx: Create distinct pre-processed mkimage
config files), *.cfgtmp files are no longer generated. There is no need
to remove them on the 'clean' target anymore.
Rename the .gitignore glob to *.cfgout.
Cc: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Commit e19b0fb485 (kbuild: generate u-boot.cfg as a byproduct of
include/autoconf.mk) removed the use of the cpp_cfg macro in Makefile,
but forgot to remove its definition.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
As many targets are now commonly built with gcc-6 or later (which
defaults to a newer C standard than older compilers), certain C
constructs are now being used as they produce more readable code. And
while all compilers that we support building with support the C11
standard (and GNU11) they do not default to that standard. Ensure that
we pass along -std=gnu11 when building.
Signed-off-by: Tom Rini <trini@konsulko.com>
Files *.so are generated files. So the clean target should delete them.
Reported-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Files *.efi are generated files. So the clean target should delete them.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Align Kconfig to Linux 4.17-rc4 with minimal impact on non-kconfig files.
Previous Kconfig sync was done by commit bf7ab1e70f ("kconfig:
re-sync with Linux 4.10") and it achieved almost perfect alignment with
a few (intended) exceptions, caused by below U-boot commits:
[A] v2015.04 5f9eb22075 ("kbuild: remove scripts/multiconfig.sh")
[B] v2015.07 20c20826ef ("Kconfig: Enable usage of escape char '\' in string values")
[C] v2016.01 da58dec866 ("Various Makefiles: Add SPDX-License-Identifier tags")
[D] v2016.03 5b8031ccb4 ("Add more SPDX-License-Identifier tags")
[E] v2016.03 192bc6948b ("Fix GCC format-security errors and convert sprintfs.")
Here is the list of Kconfig commits which followed the v4.10 alignment:
[F] v2018.01 0931ed3c0d ("kconfig/symbol.c: use correct pointer type argument for sizeof")
[G] v2018.03 1414e09b4f ("kconfig: revert change that was not needed for -Wformat-security")
[H] v2018.05 83d290c56f ("SPDX: Convert all of our single license tags to Linux Kernel style")
Commit [F] was subsequently applied to Linux kernel as commit [I]
with the same patch id, so it won't contribute to further misalignment.
[I] v4.15-rc1 88127dae6ed9 ("kconfig/symbol.c: use correct pointer type argument for sizeof")
Commit [G] is a Kconfig-specific revert of commit [E].
Commit [H] relocated and reformatted the license doing no functional change.
In summary, the only functional change that makes U-boot Kconfig
diverge from Linux Kconfig is commit [B]. After a brief analysis,
the purpose of [B] seems to be placing "\n" literals in string symbols
like CONFIG_AUTOBOOT_PROMPT="autoboot in %d seconds\n" in order to pass
them directly to printf and expect correct output at runtime. Currently,
Linux doesn't seem to have this requirement, so for the moment [B] looks
like a U-boot specific feature/fix. From point of view of further Kconfig
alignment and backporting efforts, it is highly desired that commits
like [B] are propagated to Linux and any Kconfig fixes/features are
contributed to Linux kernel first. This specific Kconfig re-sync just
keeps [B] in place.
Contrary to 4.10 Kconfig re-sync (which achieves zero non-kconfig
changes), 4.17-rc4 re-sync does some amount of updates in Kbuild
(striving to keep them at minimum), due to a number of reasons:
* Kbuild is affected by the removal of Kconfig "*shipped" files and now
requires flex and bison pre-installed on the host.
* PYTHON{2,3} variables are defined in top-level Makefile as
prerequisite for running the newly developed Kconfig unit tests.
* silentoldconfig becomes an "internal implementation detail" deprecated
for external use, being renamed to syncconfig.
The exact non-kconfig files touched by this commit are:
$ git show --format="" --stat -- ':!scripts/kconfig'
.gitignore | 2 ++
Makefile | 9 +++++++--
scripts/Makefile.build | 11 +++++++++++
scripts/Makefile.lib | 41 ++++++++++++-----------------------------
The imported Linux commits touching the above files are:
c054be10ffdbd5 ("remove gperf left-overs from build system")
73a4f6dbe70a1b ("kbuild: add LEX and YACC variables")
033dba2ec06c47 ("kbuild: prepare to remove C files pre-generated by flex and bison")
eea199b445f64c ("kbuild: remove unnecessary LEX_PREFIX and YACC_PREFIX")
e71de5ee08dcb0 ("kbuild: remove remaining use of undefined YACC_PREFIX")
d59fbbd09d5d6b ("kbuild: replace hardcoded bison in cmd_bison_h with $(YACC)")
911a91c39cabcb H ("kconfig: rename silentoldconfig to syncconfig")
59889300274569 (".gitignore: move *.lex.c *.tab.[ch] patterns to the top-level .gitignore")
9a8dfb394c0467 ("kbuild: clean up *.lex.c and *.tab.[ch] patterns from top-level Makefile")
833e622459432e H ("genksyms: generate lexer and parser during build instead of shipping")
b23d1a241f4eb4 H ("kbuild: add %.lex.c and %.tab.[ch] to 'targets' automatically")
e9781b52d4e0e3 H ("kbuild: add PYTHON2 and PYTHON3 variables")
The commits marked with 'H' are assessed as "hard" (build will fail)
prerequisites and the rest of them are assessed as "soft" prerequisites
for the re-sync. In spite of relatively high number of non-H commits,
they belong to this Kconfig update topic-wise and decrease the number of
cherry pick conflicts for many commits in this series. Additional effort
can be put in eliminating the soft prerequisites, if really needed.
The commits which contributed to this Kconfig re-sync are listed below.
Whenever a conflict resolution has been performed (mostly by hand, but
sometimes automatically by git), it is revealed by the '!' sign in the
second column, which means a patch id mismatch between Linux and U-boot
commits:
9be3213b14d44f ("gconfig: remove misleading parentheses around a condition")
ff85a1a80e0034 ("kconfig: Check for libncurses before menuconfig")
ad8181060788c8 ("kconfig: fix sparse warnings in nconfig")
cb77f0d623ff33 ! ("scripts: Switch to more portable Perl shebang")
bb3290d91695bb ! ("Remove gperf usage from toolchain")
c054be10ffdbd5 ("remove gperf left-overs from build system")
b24413180f5600 ! ("License cleanup: add SPDX GPL-2.0 license identifier to files with no license")
9059a3493efea6 ! ("kconfig: fix relational operators for bool and tristate symbols")
2c37e08464a850 ("kconfig: Warn if choice default is not in choice")
33ca1a24866373 ("kconfig: Document the 'menu' struct")
52aede4ba5efd1 ("kconfig: Document the 'symbol' struct")
c873443430ebd1 ("kconfig: Sync zconf.y with zconf.tab.c_shipped")
9a826842ff2fbd ("kconfig: Rename menu_check_dep() to rewrite_m()")
fa8cedaef814ce ("kconfig: Clarify expression rewriting")
f77850d3fe0c96 ("kconfig: Clean up modules handling and fix crash")
e3b03bf29d6b99 ("kconfig: display recursive dependency resolution hint just once")
73a4f6dbe70a1b ! ("kbuild: add LEX and YACC variables")
033dba2ec06c47 ! ("kbuild: prepare to remove C files pre-generated by flex and bison")
29c833061c1d8c ("kconfig: generate lexer and parser during build instead of shipping")
26e47a3c11a25c ("kconfig: Don't leak symbol names during parsing")
24161a6711c945 ("kconfig: Don't leak 'source' filenames during parsing")
bc28fe1d5ede88 ("kconfig: Don't leak 'option' arguments during parsing")
0724a7c32a54e3 ("kconfig: Don't leak main menus during parsing")
ae7440ef0c8013 ("kconfig: Fix automatic menu creation mem leak")
5b1374b3b3c2fc ("kconfig: Fix expr_free() E_NOT leak")
7cf33f88e29410 ("kconfig: Fix choice symbol expression leak")
05cccce580456d ("kconfig: Document automatic submenu creation code")
0735f7e5def2ab ("kconfig: Document important expression functions")
df60f4b92d3d0b ("kconfig: Remove menu_end_entry()")
b92d804a51796b ("kconfig: drop 'boolean' keyword")
6479f327dea60d ("kconfig: Warn if there is more than one help text")
52e58a3caeba5d ("kconfig: make input_mode static")
5a3dc717b3c785 ("kconfig: make xfgets() really static")
84dd95d4f87a0d ("kconfig: make conf_unsaved a local variable of conf_read()")
765f4cdef6f80d ("kconfig: use default 'yy' prefix for lexer and parser")
eea199b445f64c ("kbuild: remove unnecessary LEX_PREFIX and YACC_PREFIX")
e71de5ee08dcb0 ("kbuild: remove remaining use of undefined YACC_PREFIX")
d59fbbd09d5d6b ! ("kbuild: replace hardcoded bison in cmd_bison_h with $(YACC)")
3e41ba05b6d60c ("kconfig: Document SYMBOL_OPTIONAL logic")
d3465af60f4471 ("kconfig: Clarify choice dependency propagation")
9d1a9e8bc18bea ("kconfig: Document 'if' flattening logic")
b53688014e3325 ("kconfig: Clarify menu and 'if' dependency propagation")
d0fd0428ecf04b ("kconfig: fix make xconfig when gettext is missing")
312ee68752faaa ("kconfig: announce removal of oldnoconfig if used")
1ccb27143360bd ("kconfig: make "Selected by:" and "Implied by:" readable")
cedd55d49dee94 ! ("kconfig: Remove silentoldconfig from help and docs; fix kconfig/conf's help")
1b9eda2e4892cb ("kconfig: Warn if help text is blank")
cb67ab2cd2b8ab ("kconfig: do not write choice values when their dependency becomes n")
4f208f392103e8 ("kconfig: show '?' prompt even if no help text is available")
cd58a91def2acc ("kconfig: remove 'config*' pattern from .gitignnore")
d2a04648a5dbc3 ("kconfig: remove check_stdin()")
f3ff6fb5db68bc ("kconfig: echo stdin to stdout if either is redirected")
9e3e10c725360b ("kconfig: send error messages to stderr")
d717f24d8c6808 ("kconfig: add xrealloc() helper")
523ca58b7db2e3 ("kconfig: remove const qualifier from sym_expand_string_value()")
cd81fc82b93fa4 ("kconfig: add xstrdup() helper")
f4bc1eefc1608e ("kconfig: set SYMBOL_AUTO to the symbol marked with defconfig_list")
bf0bbdcf100322 ("kconfig: Don't leak choice names during parsing")
1a90ce36c6eff6 ("kconfig: Update ncurses package names for menuconfig")
5ae6fcc4bb82bd ("kconfig: fix line number in recursive inclusion error message")
07a422bb213adb ! ("kbuild: restore autoksyms.h touch to the top Makefile")
9a47ceec543bfb ("kconfig: clean-up reverse dependency help implementation")
d9119b5925a03b ("kconfig: Print reverse dependencies in groups")
f467c5640c29ad ("kconfig: only write '# CONFIG_FOO is not set' for visible symbols")
59a80b5e892dde ("kconfig: do not call check_conf() for olddefconfig")
4bb3a5b085cd6f ("kconfig: remove unneeded input_mode test in conf()")
99f0b6578bab44 ("kconfig: remove redundant input_mode test for check_conf() loop")
2aad9b89621386 ("kconfig: hide irrelevant sub-menus for oldconfig")
81d2bc2273052e ("kconfig: invoke oldconfig instead of silentoldconfig from local*config")
911a91c39cabcb ! ("kconfig: rename silentoldconfig to syncconfig")
2a61625835c7c8 ! ("kconfig: remove redundant streamline_config.pl prerequisite")
022a4bf6b59dfd ("kconfig: tests: add framework for Kconfig unit testing")
1903c511905984 ("kconfig: tests: add basic choice tests")
49ac3c0c3aa3b7 ("kconfig: tests: test automatic submenu creation")
b76960c0f6b25d ("kconfig: tests: test if new symbols in choice are asked")
930c429a656fdb ("kconfig: tests: check unneeded "is not set" with unmet dependency")
ee236610653ede ("kconfig: tests: check visibility of tristate choice values in y choice")
beaaddb625400e ("kconfig: tests: test defconfig when two choices interact")
3e4888c2e3d77d ("kconfig: tests: test randconfig for choice in choice")
29c434f367ea7b ("kconfig: tests: test if recursive dependencies are detected")
e2c75e7667c737 ("kconfig: tests: test if recursive inclusion is detected")
f622f827958162 ("kconfig: warn unmet direct dependency of tristate symbols selected by y")
f8f69dc0b4e070 ("kconfig: make unmet dependency warnings readable")
26561514cc9def ("kconfig: do not include both curses.h and ncurses.h for nconfig")
32a94b8b0c3e5a ("kconfig: remove duplicated file name and lineno of recursive inclusion")
379a8eb8eb1a55 ("kconfig: detect recursive inclusion earlier")
18492685e479fd ("kconfig: use yylineno option instead of manual lineno increments")
59889300274569 ! (".gitignore: move *.lex.c *.tab.[ch] patterns to the top-level .gitignore")
9a8dfb394c0467 ! ("kbuild: clean up *.lex.c and *.tab.[ch] patterns from top-level Makefile")
833e622459432e ! ("genksyms: generate lexer and parser during build instead of shipping")
b23d1a241f4eb4 ! ("kbuild: add %.lex.c and %.tab.[ch] to 'targets' automatically")
17baab68d337a0 ("kconfig: extend output of 'listnewconfig'")
e9781b52d4e0e3 ! ("kbuild: add PYTHON2 and PYTHON3 variables")
The current Kconfig update generates below build-time warnings:
YACC scripts/dtc/dtc-parser.tab.h
scripts/dtc/dtc-parser.y: warning: 3 shift/reduce conflicts [-Wconflicts-sr]
YACC scripts/dtc/dtc-parser.tab.c
scripts/dtc/dtc-parser.y: warning: 3 shift/reduce conflicts [-Wconflicts-sr]
This seems to happen because the Kbuild updates apparently didn't make
room for both "*shipped"-based builds and flex/bison-based builds. A
similar problem has been reported for genksyms parser in v4.17-rc1
commit 833e622459432e ("genksyms: generate lexer and parser during build
instead of shipping"). I have figured out empirically that the warnings
are healed after updating the in-tree U-boot DTC to upstream v1.4.6-9,
same as done by Linux v4.17-rc1 commit 9130ba88464032 ("scripts/dtc:
Update to upstream version v1.4.6-9-gaadd0b65c987"). Whether fixing the
DTC-related yacc warnings should be done together with the Kconfig
re-sync, I would like to hear from community.
My testing was limited to:
- make defconfig all
- make ARCH=arm CROSS_COMPILE=aarch64-linux-gnu- r8a7795_ulcb_defconfig all
- comparing .config before and after the re-sync
- running the newly imported Kconfig unit tests as seen below:
$ make testconfig
Tested-by: Petr Vorel <petr.vorel@gmail.com>
============================= test session starts =============================
scripts/kconfig/tests/auto_submenu/__init__.py::test PASSED [ 7%]
scripts/kconfig/tests/choice/__init__.py::test_oldask0 PASSED [ 14%]
scripts/kconfig/tests/choice/__init__.py::test_oldask1 PASSED [ 21%]
scripts/kconfig/tests/choice/__init__.py::test_allyes PASSED [ 28%]
scripts/kconfig/tests/choice/__init__.py::test_allmod PASSED [ 35%]
scripts/kconfig/tests/choice/__init__.py::test_allno PASSED [ 42%]
scripts/kconfig/tests/choice/__init__.py::test_alldef PASSED [ 50%]
scripts/kconfig/tests/choice_value_with_m_dep/__init__.py::test PASSED [ 57%]
scripts/kconfig/tests/err_recursive_inc/__init__.py::test PASSED [ 64%]
scripts/kconfig/tests/inter_choice/__init__.py::test PASSED [ 71%]
scripts/kconfig/tests/new_choice_with_dep/__init__.py::test PASSED [ 78%]
scripts/kconfig/tests/no_write_if_dep_unmet/__init__.py::test PASSED [ 85%]
scripts/kconfig/tests/rand_nested_choice/__init__.py::test PASSED [ 92%]
scripts/kconfig/tests/warn_recursive_dep/__init__.py::test PASSED [100%]
========================== 14 passed in 0.34 seconds ==========================
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Petr Vorel <petr.vorel@gmail.com>
Following the conversion of the SPDX license tags, a number of files
compiled with -pedantic now generate warnings similar to the following
for using C99-style '//' comments in ISO C90 code:
tools/gen_eth_addr.c:1:1: warning: C++ style comments are not allowed in ISO C90
// SPDX-License-Identifier: GPL-2.0+
^
The SPDX comment-style change means that these files have adopted C99,
so need to change the language-standard to --std=gnu99 or --std=gnu11
to let the compiler know this.
As we now require GCC 6 or newer for the cross-compiler, the project has
implicitly moved the project to GNU11: let older GCC versions on various
Linux distros know to treat our host tools as GNU11 as well.
References: commit 83d290c56f ("SPDX: Convert all of our single license tags to Linux Kernel style")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
The __FILE__ macro is used everywhere in U-Boot to locate the file
printing the log message, such as WARN_ON(), etc. If U-Boot is
built out of tree, this can be a long absolute path.
This is because Kbuild runs in the objtree instead of the srctree,
then __FILE__ is expanded to a file path prefixed with $(srctree)/.
A brand-new option from GCC, -fmacro-prefix-map, solves this problem.
If your compiler supports it, __FILE__ is the relative path from the
srctree regardless of O= option. This provides more readable log,
more reproducible builds, and smaller image size.
[ Linux commit: a73619a845d5625079cc1b3b820f44c899618388 ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Re-sync the logic about which clang warnings to disable from v4.17-rc1.
Note that we don't disable all of the same ones as for now we haven't
run into any cases of warnings from clang in code from upstream Linux.
Signed-off-by: Tom Rini <trini@konsulko.com>
The current makefile logic disables creation of the
SPL.log/u-boot-ivt.img.log etc. files when V=1 is given on the command
line, the rationale presumably being that the user wants and gets the
information on the console.
However, from general principles, I don't think a higher V= level
should affect which build artifacts get generated (and certainly
shouldn't produce fewer). Concretely, it's also a problem that when
doing a V=1 build in a terminal, the relevant HAB blocks lines easily
drown in all the other V=1 output.
Moreover, build systems such as Yocto by default pass V=1, so in that
case the information gets hidden away in the do_compile log file, making
it nigh impossible to create a recipe for creating signed U-boot images
- I don't want to disable V=1, because having verbose output in the log
file is valuable when things go wrong, but OTOH trying to go digging in
the do_compile log file (and getting exactly the right lines) is not
pleasant to even think about.
So change the logic so that for V=0, the mkimage output is redirected
to MKIMAGEOUTPUT (which is also the current behaviour), while for any
other value of V, we _additionally_ write the information to make's
stdout, whatever that might be.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Tested-by: Breno Lima <breno.lima@nxp.com>
Make it possible to use gcc code coverage analysis.
v1 -> v2:
- Kconfig: remove not needed 'default n'
- Makefile: use consistent spacing
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Modifying the default environment via CONFIG_EXTRA_ENV_SETTINGS is
somewhat inflexible, partly because the cpp language does not allow
appending to an existing macro. This prevents reuse of "environment
fragments" for different boards, which in turn makes maintaining that
environment consistently tedious and error-prone.
This implements a Kconfig option for allowing one to define the entire
default environment in an external file, which can then, for example, be
generated programmatically as part of a Yocto recipe, or simply be kept
in version control separately from the U-boot repository.
Tested-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
With the most recent tools for ARC (arc-2017.09) in case of
"naked" function compiler throws a warning:
---------------------------------->8-----------------------------
board/synopsys/hsdk/hsdk.c: In function 'hsdk_core_init_f':
board/synopsys/hsdk/hsdk.c:345:1: warning: stack usage computation not supported for this target
}
^
---------------------------------->8-----------------------------
That happens because the compiler doesn't handle "naked" functions
as a special case where stack calculation shouldn't be done.
But for now until this is fixed in GCC to get clean buildman output
we're disabling stack-usage check for ARC.
See https://lists.denx.de/pipermail/u-boot/2018-April/324455.html
for more background.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tom Rini <trini@konsulko.com>
Create u-boot-ivt.img and u-boot-ivt.img.log when building U-Boot
with SPL and Secure Boot enabled for imx7 (like it is done for imx6).
See commit d21bd69b6e for more info.
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
In README.sunxi64 we tell the user how to optionally create
u-boot-sunxi-with-spl.bin by manually running cat. Instead, have the
build system create the file automatically just like it does for 32-bit
sunxi boards.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
We're going to need this logic for 64-bit builds as well, so move it
out from under arch/arm/cpu/armv7.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The u-boot-spl.srec is needed for some platforms, add target to generate this file.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Tom Rini <trini@konsulko.com>
The u-boot-elf.srec is needed for some platforms, add target to generate this file.
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Most of architectures have .text section situated in the very beginning
of U-Boot binary and thus it is very logical that CONFIG_SYS_TEXT_BASE
is used on final linkage step to specify where U-Boot gets linked to.
For that we pass the following construction to the LD:
---------------------------->8-----------------------
xxx-ld ... -Ttext $(CONFIG_SYS_TEXT_BASE) ...
---------------------------->8-----------------------
But there could be exceptions. For example:
1. In case of ARCv2 we want to put vectors table in its own section
.ivt in front of .text section which means we need either add an
offset to CONFIG_SYS_TEXT_BASE to compensate for .ivt or don't
pass "-Ttext" to the LD at all and specify link base in linker
script directly.
2. Some architectures even though have .text section in the very
beginning of the U-Boot image still use different symbols to
specify link-base:
* NIOS2: CONFIG_SYS_MONITOR_BASE (which I really like because
that exactly what makes sense - where out image starts but not
beginning of its .text section which just happened to match the
whole image beginning)
* EXTENSA: CONFIG_SYS_TEXT_ADDR
* X86: Which doesn't use CONFIG_SYS_MONITOR_BASE in case of EFI
otherwise sets explicit link base in u-boot.lds
I think that's good to allow for flexibility and don't require each and
every architecture or even platform to specify CONFIG_SYS_TEXT_BASE as well
as use it to set .text section location.
So let's only pass "-Ttext xxx" for those architectures who don't set
link-base explicitly in their linker scripts.
This patch iaddresses comments for previously sent
https://patchwork.ozlabs.org/patch/867540/.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
The make macro to check if the binary exceeds the board size limit is not
called. Make sure that is the case.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
With CONFIG_SYS_INIT_SP_BSS_OFFSET enabled, the initial (pre-relocation)
stack is placed some distance after bss_start. The control DTB is appended
to the U-Boot binary at bss_start. If the DTB is too large, or the SP BSS
offset too small, then the initial stack could corrupt the DTB. Enhance
the Makefile to check whether this is likely to occur.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add prelink-riscv to arrange .rela.dyn and .rela.got
in compile time. So that u-boot can be directly
executed without fixup.
Signed-off-by: Chih-Mao Chen <cmchen@andestech.com>
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Signed-off-by: Greentime Hu <green.hu@gmail.com>
Update tegra to use binman for image creation. This still includes the
current Makefile logic, but a later patch will remove this. Three output
files are created, all of which combine
SPL and U-Boot:
u-boot-tegra.bin - standard image
u-boot-dtb-tegra.bin - same as u-boot-tegra.bin
u-boot-nodtb-target.bin - includes U-Boot without the appended device tree
The latter is useful for build systems where the device is appended later,
perhaps after being modified.
Signed-off-by: Simon Glass <sjg@chromium.org>
With commit 84d46e7e89 ("tools: env: allow to print U-Boot version")
the fw_env utilities need the version.h header file. Building only
the envtools in a pristine build directory will fail due to missing
header files.
Make sure the header files are a dependency of the envtools target.
Fixes: 84d46e7e89 ("tools: env: allow to print U-Boot version")
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When building on a multi-core machine for an SPL-enabled board that
also uses CONFIG_OF_EMBED, the following error can be encountered
due to a race condition:
make[3]: *** No rule to make target 'spl/dts/dt.dtb.o', needed by
'spl/dts/built-in.o'. Stop.
../scripts/Makefile.spl:364: recipe for target 'spl/dts' failed
make[2]: *** [spl/dts] Error 2
make[2]: *** Waiting for unfinished jobs....
A reliable way to trigger this race condition is to add "sleep 60" to
the end of the "arch-dtbs" rule's recipe in "dts/Makefile" and to build
U-Boot against a board which uses the CONFIG_OF_EMBED and CONFIG_SPL
options using "make -j8" or a similar command.
This commit corrects this race condition via the use of CONFIG_OF_EMBED
in the same way that commit 3c00a2c8b5 ("Makefile: Correct dependency
race condition with TPL") and commit 054b3a1e80 ("dm: Makefile: Build
of-platdata before SPL") use CONFIG_OF_SEPARATE.
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Coccinelle is a program for static code analysis.
For details on Coccinelle see
http://coccinelle.lip6.fr/
Add scripts/coccicheck copied from Linux kernel v4.14.
The coccicheck script executes the tests *.cocci in
directory scripts/coccinelle by calling spatch.
In Makefile add a coccicheck target. You can use it with
make coccicheck MODE=<mode>
where mode in patch, report, context, org.
Add a copy of Linux v4.14 file Documentation/dev-tools/coccinelle.rst
as doc/README.coccinelle.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Currently, pylibfdt is always compiled if swig is installed on your
machine. It is really annoying because most of targets (excepts
x86, sunxi, rockchip) do not use dtoc or binman.
"checkbinman" and "checkdtoc" are wrong. It is odd that the final
build stage checks if we have built necessary tools. If your platform
depends on dtoc/binman, you must be able to build pylibfdt. If swig
is not installed, it should fail immediately.
I added PYLIBFDT, DTOC, BINMAN entries to Kconfig. They should be
property select:ed by platforms that need them. Kbuild will descend
into scripts/dtc/pylibfdt/ only when CONFIG_PYLIBFDT is enabled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The pylibfdt is used by dtoc (and, indirectly by binman), but there
is no reason why it must be generated in the tools/ directory.
Recently, U-Boot switched over to the bundled DTC, and the directory
structure under scripts/dtc/ now mirrors the upstream DTC project.
So, scripts/dtc/pylibfdt is the best location.
I also rewrote the Makefile in a cleaner Kbuild style.
The scripts from the upstream have been moved as follows:
lib/libfdt/pylibfdt/setup.py -> scripts/dtc/pylibfdt/setup.py
lib/libfdt/pylibfdt/libfdt.i -> scripts/dtc/pylibfdt/libfdt.i_shipped
The .i_shipped is coped to .i during building because the .i must be
located in the objtree when we build it out of tree.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Up to now we depended on an exported variable to build u-boot.rom.
We should be able to specify it in the configuration file, too.
With this patch this becomes possible using the new Kconfig option
CONFIG_BUILD_ROM.
This option depends on CONFIG_X86 and is selected in
qemu-x86_defconfig and qemu-x86_64_defconfig.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
CONFIG_FIT_EMBED might be confused with CONFIG_OF_EMBED, rename it
MULTI_DTB_FIT as it is able to get a DTB from a FIT image containing
multiple DTBs. Also move the option to the Kconfig dedicated to the DTS
options and create a README for this feature.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This makes us act like the Linux Kernel does and allow for dtc to be
provided externally but otherwise we use the version of dtc that is
included in the sources. This in turn means that we can drop the
checkdtc logic. We select DTC in the cases where we will need the dtc
tool provided.
Signed-off-by: Tom Rini <trini@konsulko.com>
With support for overlays and calling the -@ flag to dtc we need to have
at least 1.4.3 available now.
Cc: Simon Glass <sjg@chromium.org>
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
EFI_LOADER really wants UTF-16 strings (ie. %ls and L"string" are 16bit
chars instead of 32bit chars). But rather than enabling -fshort-wchar
conditionally if EFI_LOADER is enabled, it was deemed preferrable to
globally switch.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This was broken by the recent environment refactoring. Specifically:
$ make environ
scripts/Makefile.build:59: tools/environ/Makefile: No such file or directory
make[1]: *** No rule to make target 'tools/environ/Makefile'. Stop.
make: *** [Makefile:1469: environ] Error 2
Fix this by updating the Makefile and adjusting the #include filesnames in
two C files.
Fixes: ec74f5f (Makefile: Rename 'env' target to 'environ')
Reported-by: Måns Rullgård <mans@mansr.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
With the move of environment code from common/ to env/ a number of
changes needed to be made to various make targets. We missed updating
some of the files required for out of tree builds of the tools. Correct
the 'environ' target to know that we need to work under tools/env/ still
(not tools/environ/) and then update the wrappers in env_attr.c and
env_flags.c to point to the new correct file.
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
