Commit graph

2330 commits

Author SHA1 Message Date
Ashish Kumar
63b2316c5c fsl-layerscape: Consolidate registers space defination for CCI-400 bus
CoreLink Cache Coherent Interconnect (CCI) provides full cache
coherency between two clusters of multi-core CPUs and I/O coherency
for devices and I/O masters.

This patch add new config option SYS_FSL_HAS_CCI400 and moves
existing register space definaton of CCI-400 bus to fsl_immap to be
shared. CONFIG_SYS_CCI400_ADDR is replaced with SYS_CCI400_OFFSET
in Kconfig.

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: revised commit message, squashed patches for armv8 and armv7]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 07:55:36 -07:00
Tom Rini
470135be27 Merge git://www.denx.de/git/u-boot-imx
Update pfla02 for setenv changes and PHYLIB/etc migration to Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-16 18:12:00 -04:00
Simon Glass
382bee57f1 env: Rename setenv() to env_set()
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:22:18 -04:00
Peng Fan
11d94319c3 arm: Implement workaround for Cortex-A9 errata 845369
Under very rare timing circumstances, transitioning into streaming
mode might create a data corruption. Present on Two or more processors
or 1 core with ACP, all revisions. This erratum can be worked round
by setting bit[22] of the undocumented Diagnostic Control Register to 1.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-08-16 11:50:51 +02:00
xypron.glpk@gmx.de
6def7de37b bcm281xx: clock: avoid possible NULL dereference
It does not make sense first to dereference c and then
to check if it is NULL.

The problem was indicated by cppcheck.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2017-08-13 15:17:27 -04:00
xypron.glpk@gmx.de
65e8ce29e4 arm: bcm235xx: clk_set_rate avoid possible NULL deref
It does not make sense first to dereference c and then
to check if it is NULL.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2017-08-13 15:17:27 -04:00
xypron.glpk@gmx.de
b69a0849e7 arm: bcm235xx: avoid possible NULL dereference
It does not make sense to first dereference c and then
check if it is NULL.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2017-08-13 15:17:26 -04:00
Simon Glass
6500ec7a5a Convert CONFIG_CMD_PCI to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_PCI

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-11 15:41:50 -04:00
Stefano Babic
552a848e4f imx: reorganize IMX code as other SOCs
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.

This change is also coherent with the structure in kernel.

Signed-off-by: Stefano Babic <sbabic@denx.de>

CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2017-07-12 10:17:44 +02:00
Vanessa Maegima
d7c11502df mx6sabreauto: Update to SPL only mode
As mx6sabreauto supports SPL now, all variants can boot using the same
defconfig.

This patch:
- Removes non-SPL targets.
- Renames target to mx6sabreauto_defconfig.
- Renames folder and board files to mx6sabreauto.
- Updates MAINTAINERS, Makefile and Kconfig accordingly.
- Removes .cfg files.
- Adds a README with instructions to build and flash SPL and u-boot.img.

Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-07-12 09:44:22 +02:00
Vanessa Maegima
823dff9d02 mx6qsabreauto: Add SPL support
Add support for mx6q, mx6dl and mx6qp sabreauto boards in SPL.

Retrieved the mx6q DCD table from:
board/freescale/mx6qsabreauto/imximage.cfg

Retrieved the mx6dl DCD table from:
board/freescale/mx6qsabreauto/mx6dl.cfg

Retrieved the mx6qp DCD table from:
board/freescale/mx6qsabreauto/mx6qp.cfg

Flashed SPL and u-boot.img to an SD card and could successfully boot it
on mx6q, mx6qp and mx6dl sabreauto boards.

Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-07-12 09:44:22 +02:00
Fabio Estevam
a1d1fdc920 mx6: soc: Move mxs_dma_init() into the mxs nand driver
Currently the following build error is seen when a board using MMC SPL
is built and the MXS nand driver is also selected:

arch/arm/cpu/armv7/built-in.o: In function `arch_cpu_init':
arch/arm/cpu/armv7/mx6/soc.c:432: undefined reference to 'mxs_dma_init'

On mx6 the only user of mxs_dma_init() is the mxs nand driver, so
move it there.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-07-12 09:44:22 +02:00
Stefan Agner
3fd9579085 imx: mx6ull: fix USB bmode for i.MX 6UL and 6ULL
i.MX 6UL and 6ULL have different boot device capabilities and
use therefor use a different boot device selection table than
other i.MX 6 devices. Particularly, the value which has been
used so far (b0001) is assigned to QSPI boot for these two
devices.

There is no common reserved value for all i.MX 6devices. Use
b0010 for i.MX 6UL and 6ULL via compile time ifdef.

Reported-by: Joël Esponde <joel.esponde@honeywell.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Joël Esponde <joel.esponde@honeywell.com>
2017-07-12 09:42:33 +02:00
Simon Glass
8eab1a58dd dm: scsi: Document and rename the scsi_scan() parameter
The 'mode' parameter is actually a flag to determine whether to display
a list of devices found during the scan. Rename it to reflect this, add a
function comment and adjust callers to use a boolean.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-07-11 10:08:19 -06:00
Simon Glass
10e40d54b3 Kconfig: Add CONFIG_SATA to enable SATA
At present CONFIG_CMD_SATA enables the 'sata' command which also brings
in SATA support. Some boards may wish to enable SATA without the command.
Add a separate CONFIG to permit this.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-07-11 10:08:19 -06:00
Simon Glass
3bf926c0dd Convert CONFIG_CMD_SATA to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_SATA

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-07-11 10:08:19 -06:00
Simon Glass
fedb428c5b Convert CONFIG_SCSI to Kconfig
This converts the following to Kconfig:
   CONFIG_SCSI

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-07-11 10:08:19 -06:00
Tom Rini
821560fd8e Merge git://www.denx.de/git/u-boot-imx
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	include/configs/imx6qdl_icore_rqs.h
	include/configs/imx6ul_geam.h
	include/configs/imx6ul_isiot.h
2017-06-27 09:32:37 -04:00
Fabio Estevam
65496a3483 mx6: soc: Fix typo in temperature unit name
The correct name is 'Celsius', so fix it accordingly.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-06-27 09:06:09 +02:00
Chen-Yu Tsai
3474827294 sunxi: psci: Move entry address setting to separate function
Currently we set the entry address in the psci_cpu_on function.
However R40 has a different register for this. This resulted in
an #ifdef / #else block in psci_cpu_on, which we avoided having
in the first place.

Move this part into a separate function, defined differently for
the R40 as opposed to the other single cluster platforms.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2017-06-12 15:41:02 +05:30
Tom Rini
ffb5656862 armv7: Mark the default lowlevel_init function as weak
Rather than have a long and if check in the Makefile, mark the default
lowlevel_init function as weak (as we do on armv8) so that SoCs can
override it if needed, and it will still be discarded if unused.
Provide a weak s_init as well to allow for this to link and be
discarded.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-05 11:02:23 -04:00
Vanessa Maegima
1541d7a63d pico-imx7d: Add initial support
Add the initial support for pico-imx7d board based on Wig Cheng's
source code.

Add support for eMMC, USB gadget, I2C, PMIC and Ethernet.

For more information about this board, please visit:
http://www.technexion.org/products/pico/pico-som/pico-imx7-emmc

Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-05-31 09:58:40 +02:00
Simon Glass
51f2937036 Convert CONFIG_CMD_FUSE to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_FUSE

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 09:33:58 -04:00
Jagan Teki
bc1fe9006d icorem6: Make SPL to pick suitable fdt
SPL FIT is able to pick the suitable fdt file for u-boot,
so add that function through board_fit_config_name_match.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-05-18 11:23:31 +02:00
Jagan Teki
9786496cdc geam6ul: Add modeboot env via board_late_init
Add runtime, modeboot env which is setting mmcboot, or
nandboot based on the bootdevice so-that conditional
macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should
be avoided in config files.

Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-05-18 11:23:31 +02:00
Jagan Teki
98f5661033 icorem6: Add modeboot env via board_late_init
Add runtime, modeboot env which is setting mmcboot, or
nandboot based on the bootdevice so-that conditional
macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should
be avoided in config files.

Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-05-18 11:23:31 +02:00
Nisal Menuka
8776350d87 Add ARM errata workaround 852421 and 852423 for Cortex-A17
ARM errata 852421 and 852423 applies to r1p0, r1p1 and r1p2
revisions of Cortex-A17 processors. These workarounds
exist in Linux kernel and I thought it would be better
to add them in to U-Boot.

Signed-off-by: Nisal Menuka <nisalmenuka23@gmail.com>
2017-05-08 11:57:36 -04:00
Tom Rini
26d61195f8 fdt: Move fdt_fixup_ethernet to a common place
With 3f66149d9f we no longer have a common call fdt_fixup_ethernet.
This was fine to do on PowerPC as they largely had calls already in
ft_cpu_fixup.  On ARM however we largely relied on this call.  Rather
than introduce a large number of changes to ft_cpu_fixup /
ft_board_fixup we recognize that this is a common enough call that we
should be doing it in a central location.  Do it early enough that we
can do any further updates in ft_cpu_fixup / ft_board_fixup.

Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Thomas Chou <thomas@wytron.com.tw> (maintainer:NIOS)
Cc: York Sun <york.sun@nxp.com> (maintainer:POWERPC MPC85XX)
Cc: Stefan Roese <sr@denx.de> (maintainer:POWERPC PPC4XX)
Cc: Simon Glass <sjg@chromium.org>
Cc: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Fixes: 3f66149d9f ("Remove extra fdt_fixup_ethernet() call")
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-01 09:11:59 -04:00
Tom Rini
29ec685883 arm: Re-sync ARCH_MX5 / MX51 / MX53 CONFIG options
A few boards had not been fully re-synced with CONFIG_ARCH_MX5 / CONFIG_MX51 /
CONFIG_MX53 being in Kconfig.  Do so now.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-30 10:29:38 -04:00
Tom Rini
6f008a2e16 Merge git://git.denx.de/u-boot-sunxi 2017-04-25 16:12:42 -04:00
Chen-Yu Tsai
0918648d82 sunxi: Add PSCI support for R40
The R40's CPU controls are a combination of sun6i and sun7i.

All controls are in the CPUCFG block, and it seems the R40 does not
have a PRCM block. The core reset, power gating and clamp controls
are grouped like sun6i.

Last, the R40 does not have a secure SRAM block.

This patch adds a PSCI implementation for CPU bring-up and hotplug
for the R40.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-20 13:30:01 +02:00
Tom Rini
3c476d841d Merge git://git.denx.de/u-boot-fsl-qoriq 2017-04-18 11:36:06 -04:00
Masahiro Yamada
c54bcf6805 ARM: adjust arm-smccc code for use in U-Boot
Adjust ARM SMC Calling Convention code for U-Boot:
  - Replace the license block with SPDX
  - Change path to asm-offsets.h
  - Define UNWIND() as no-op
  - Add Kconfig entry
  - Add asm-offsets

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-04-18 10:29:17 -04:00
Masahiro Yamada
c2da86f39e ARM: import arm-smccc code from Linux 4.11-rc6
Imports ARM SMC Calling Convention code from Linux 4.11-rc6.
The files have been copied as follows:

[Linux]                           [U-Boot]
arch/arm/kernel/smccc-call.S   -> arch/arm/cpu/armv7/smccc-call.S
arch/arm64/kernel/smccc-call.S -> arch/arm/cpu/armv8/smccc-call.S
arch/arm/include/asm/opcodes*  -> arch/arm/include/asm/opcodes*
include/linux/arm-smccc.h      -> include/linux/arm-smccc.h

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-04-18 10:29:16 -04:00
York Sun
73fb583829 armv7: ls1021a: Drop macro CONFIG_LS102XA
Use CONFIG_ARCH_LS1021A instead.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-04-17 09:03:30 -07:00
Tom Rini
3fea953698 Merge branch 'master' of git://git.denx.de/u-boot-video 2017-04-14 22:05:17 -04:00
Sanchayan Maity
b215fb3f34 Convert CONFIG_FSL_DCU_FB to Kconfig
Rename CONFIG_FSL_DCU_FB to CONFIG_VIDEO_FSL_DCU_FB
and convert it to Kconfig.

Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
2017-04-14 13:37:35 +02:00
Tom Rini
1622559066 Merge branch 'master' of git://www.denx.de/git/u-boot-imx
Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-13 11:19:00 -04:00
Adam Ford
f479cec3b6 imx: i.mx6q: add the initial support for LogicPD i.MX6Q SOM
Logic PD has an i.MX6Q system on module (SOM) with a development kit. The
SOM has a built-in microSD socket, DDR and NAND flash.  The development kit
has an SMSC Ethernet PHY, serial debug port and a variety of peripherals.
This have been verified to boot the i.MX6Q version over either SD
on the development kit or NAND built into the SOM.  Items in the dtsi file
are specific to the SOM itself.  Items in the dts file are in the baseboard.
Future versions of the SOM will come out supporting the same basebord and
potentially future base boards will come out supporting the same SOM.

Signed-off-by: Adam Ford <aford173@gmail.com>
2017-04-12 18:59:12 +02:00
Ye Li
2018ef868c imx: mx7ulp: Fix SPLL/APLL clock rate calculation issue
The num/denom is a float value, but in the calculation it is convert
to integer 0, and wrong result.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2017-04-12 18:45:10 +02:00
Andre Przywara
4d24e5f175 fsl: ls102x: remove redundant GENERIC_TIMER_CLK
Some Freescale boards used an extra version of the constant to hold the
Generic Timer frequency. This can easily be covered by the now unified
COUNTER_FREQUENCY constant, so remove this extra variable from those
boards.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-05 15:03:17 +05:30
Andre Przywara
e4916e850b ARM: rename CONFIG_TIMER_CLK_FREQ to COUNTER_FREQUENCY
Many ARMv8 boards define a constant COUNTER_FREQUENCY to specify the
frequency of the ARM Generic Timer (aka. arch timer).
ARMv7 boards traditionally used CONFIG_TIMER_CLK_FREQ for the same
purpose. It seems useful to unify them.
Since there are less occurences of the latter version, lets convert all
users over to COUNTER_FREQUENCY.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-05 15:03:17 +05:30
Jagan Teki
a2f8a45696 configs: imx6: Select missing BOARD_LATE_INIT
Select missing BOARD_LATE_INIT from configs/ to
respective targets on arch area for Engicam imx6 boards.

Cc: Tom Rini <trini@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-03-26 11:05:57 +02:00
Tom Rini
02ccab1908 Merge branch 'master' of git://www.denx.de/git/u-boot-imx
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	configs/bk4r1_defconfig
	configs/colibri_vf_defconfig
	configs/pcm052_defconfig
	include/configs/colibri_vf.h
	include/configs/pcm052.h
2017-03-19 15:13:38 -04:00
Stefan Agner
7966b43778 ARM: vf610: move to standard arch/board approach
Move Freescale/NXP Vybrid to a standard arch/board approach, similar
to what has been done to i.MX 6 earlier in commit 89ebc82137 ("ARM:
mx6: move to a standard arch/board approach").

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2017-03-19 17:30:11 +01:00
Fabio Estevam
9b548bf856 mx7: Add 1.2GHz speed grade entry
There are recent MX7 parts that have a 1.2GHz speed grade.

Add support for it.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-03-19 17:29:03 +01:00
Fabio Estevam
60a07fb843 mx7: Fix the get_cpu_speed_grade_hz() return values
According to the MX7D fuse map the following speed grades are available:

800  MHz
500  MHz
1000 MHz
1200 MHz

So simply return the real frequency that corresponds to the speed grade.

With this change we see on boot:

CPU:   Freescale i.MX7D rev1.2 1000 MHz (running at 792 MHz)

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-03-19 17:28:59 +01:00
Fabio Estevam
31b8a9011b mx7: Fix speed grade entry
According to the MX7D fuse map the speed grade of the parts, which
return '1' is 500MHz instead of 850MHz, so fix it accordingly.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-03-19 17:28:55 +01:00
Sébastien Szymanski
77f29293f1 arm: i.MX6UL: add Armadeus Systems OPOS6UL SoM and OPOS6ULDev carrier board
OPOS6UL is an i.MX6UL based SoM with 256MB RAM, 4GB eMMC and an ethernet
phy. OPOS6ULDev is carrier board for the OPOS6UL.

U-Boot SPL 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09)
Trying to boot from MMC1

U-Boot 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09 +0100)

CPU:   Freescale i.MX6UL rev1.0 528 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 40C
Reset cause: POR
Model: Armadeus Systems OPOS6UL SoM on OPOS6ULDev board
DRAM:  256 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Video: 800x480x18
In:    serial
Out:   serial
Err:   serial
Net:   FEC [PRIME]
Hit any key to stop autoboot:  0

Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-03-19 17:28:09 +01:00
Tom Rini
3a649407a4 arm: Migrate SYS_THUMB_BUILD to Kconfig, introduce SPL_SYS_THUMB_BUILD
Today, we have cases where we wish to build all of U-Boot in Thumb2 mode for
various reasons.  We also have cases where we only build SPL in Thumb2 mode due
to size constraints and wish to build the rest of the system in ARM mode.  So
in this migration we introduce a new symbol as well, SPL_SYS_THUMB_BUILD to
control if we build everything or just SPL (or in theory, just U-Boot) in
Thumb2 mode.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
2017-03-18 20:28:01 -04:00
Jagan Teki
0421a164de imx6: isiotmx6ul: Add FEC support
Add FEC support for Engicam Is.IoT MX6UL module.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-03-17 09:27:08 +01:00
Jagan Teki
e411e67e1e imx6: isiotmx6ul: Add I2C support
Add I2C support for Engicam Is.IoT MX6UL module.

isiotmx6ul> i2c bus
Bus 0:  i2c@021a0000
Bus 1:  i2c@021a4000
isiotmx6ul> i2c dev 0
Setting bus to 0
isiotmx6ul> i2c dev
Current bus is 0
isiotmx6ul> i2c speed 100000
Setting bus speed to 100000 Hz
isiotmx6ul> i2c probe
Valid chip addresses: 00 2C 44 78
isiotmx6ul> i2c md 2C 0xff
00ff: 00 00 00 00 0f f0 01 64 ff ff 00 00 00 00 00 00    .......d........

Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-03-17 09:27:08 +01:00
Jagan Teki
e9dfa1e1e5 arm: imx6ul: Add Engicam Is.IoT MX6UL Starter Kit initial support
Boot from MMC:
-------------
U-Boot SPL 2017.01-rc2-gba3c151-dirty (Jan 02 2017 - 16:59:33)
Trying to boot from MMC1

U-Boot 2017.01-rc2-gba3c151-dirty (Jan 02 2017 - 16:59:33 +0100)

CPU:   Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 33C
Reset cause: POR
Model: Engicam Is.IoT MX6UL Starterkit
DRAM:  512 MiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
isiotmx6ul>

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-03-17 09:27:08 +01:00
Peng Fan
77fa04577a imx: imx7ulp: add EVK board support
Add EVK board support.
Add the evk dts file.

LOG:
U-Boot 2017.03-rc2-00038-gab86c1d (Feb 22 2017 - 15:59:58 +0800)

CPU:   Freescale i.MX7ULP rev1.0 at 500 MHz
Reset cause: POR
Boot mode: Dual boot
Model: NXP i.MX7ULP EVK
DRAM:  1 GiB
MMC:   FSL_SDHC: 0
In:    serial@402D0000
Out:   serial@402D0000
Err:   serial@402D0000
Net:   Net Initialization Skipped
No ethernet found.
Hit any key to stop autoboot:  0

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2017-03-17 09:27:08 +01:00
Peng Fan
27117b2024 mx7ulp: Add HAB boot support
Add CAAM clock functions, SEC_CONFIG[1] fuse checking, and default CSF
size for HAB support boot on mx7ulp.

Users need to uncomment the CONFIG_SECURE_BOOT in mx7ulp_evk.h to build
secure uboot.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
2017-03-17 09:27:08 +01:00
Peng Fan
c40d612b1a serial: lpuart: restructure lpuart driver
Drop CONFIG_LPUART_32B_REG.
Move the register structure to a common file include/fsl_lpuart.h
Define lpuart_serial_platdata structure which includes the reg base and flags.
For 32Bit register access, use lpuart_read32/lpuart_write32 which handles
big/little endian.
For 8Bit register access, still use the orignal code.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Shaohui Xie <Shaohui.Xie@nxp.com>
Cc: Alison Wang <b18965@freescale.com>
2017-03-17 09:27:08 +01:00
Ye Li
d4dcee2213 imx: mx7ulp: Implement the clock functions for i2c driver
Implement the i2c clock enable and get function for mx7ulp. These
functions are required by imx_lpi2c driver.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-03-17 09:27:08 +01:00
Peng Fan
1b409828b1 imx: mx7ulp: Add soc level initialization codes and functions
Implement soc level functions to get cpu rev, reset cause, enable cache,
etc. We will disable the wdog and init clocks in s_init at very early u-boot
phase.

Since the we are seeking the way to get chip id for mx7ulp, the get_cpu_rev
is hard coded to a fixed value. This may change in future.

Reuse some code in imx-common.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2017-03-17 09:27:08 +01:00
Peng Fan
d0f8516d9e imx: mx7ulp: Add clock framework and functions
Add a clock framework to support SCG1/PCC2/PCC3 for A7 to support get/set
clock source, divider, clock rate and parent source.
Users need to include pcc.h to use the APIs to for peripherals clock. Each
peripheral clock is defined in enum pcc_clk type.

SCG relevants APIs are defined in scg.h which supports clock rate get, PLL/PFD
enablement and settings, and all SCG clock initialization. User need use enum
scg_clk to access each clock source.

In clock.c, we initialize necessary clocks at u-boot s_init and implement the
clock functions used by driver modules to operate clocks dynamically.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2017-03-17 09:27:08 +01:00
Peng Fan
0cb3d82c68 imx: mx7ulp: add iomux driver to support IOMUXC0 and IOMUXC1
Add a new driver under ULP directory to support its IOMUXC
controllers. The ULP has two IOMUXC, the IOMUXC0 is used
for M4 domain, while IOMUXC1 is for A7. We set IOMUXC1 as
the default IOMUX in this driver. Any pins in IOMUXC0 needs
to configure with IOMUX_CONFIG_MPORTS in its mux_mode field.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
2017-03-17 09:27:08 +01:00
Peng Fan
e90a08daee imx: mx7ulp: Add mx7ulp to Kconfig
i.MX7ULP is a new series SoC which has different architecture
from previous i.MX platforms. Create a new cpu folder for it,
and add it to Kconfig.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
2017-03-17 09:27:08 +01:00
Siarhei Siamashka
19a75b8cf8 arm: omap3: Bring back ARM errata workaround 725233
The workaround for ARM errata 725233 had been lost since
commit 45bf05854b (armv7: adapt omap3 to the new cache
maintenance framework). Bring it back in order to avoid
very difficult to reproduce, but actually encountered in
the wild CPU deadlocks when running software rendered
X11 desktop on OMAP3530 hardware.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Migrate to Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-14 20:40:17 -04:00
Tom Rini
8dda2e2f9e ARM: Migrate errata to Kconfig
This moves all of the current ARM errata from various header files and in to
Kconfig.  This allows for a minor amount of cleanup as we had some instances
where both a general common header file was enabling errata as well as the
board config.  We now just select these once at the higher level in Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-09 19:52:50 -05:00
Masahiro Yamada
e856bdcfb4 flash: complete CONFIG_SYS_NO_FLASH move with renaming
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.

During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH".  Flipping the logic will
make the code more readable.  Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.

This commit was created as follows:

[1] Edit "default n" to "default y" in the config entry in
    common/Kconfig.

[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"

[3] Rename the instances in defconfigs by the following:
  find . -path './configs/*_defconfig' | xargs sed -i \
  -e '/CONFIG_SYS_NO_FLASH=y/d' \
  -e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'

[4] Change the conditionals by the following:
  find . -name '*.[ch]' | xargs sed -i \
  -e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
  -e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
  -e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
  -e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'

[5] Modify the following manually
  - Rename the rest of instances
  - Remove the description from README
  - Create the new Kconfig entry in drivers/mtd/Kconfig
  - Remove the old Kconfig entry from common/Kconfig
  - Remove the garbage comments from include/configs/*.h

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-12 14:30:25 -05:00
Tom Rini
c83a824e62 Merge git://git.denx.de/u-boot-fsl-qoriq
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	configs/ls1046aqds_defconfig
	configs/ls1046aqds_nand_defconfig
	configs/ls1046aqds_qspi_defconfig
	configs/ls1046aqds_sdcard_ifc_defconfig
	configs/ls1046aqds_sdcard_qspi_defconfig
	configs/ls1046ardb_emmc_defconfig
	configs/ls1046ardb_qspi_defconfig
	configs/ls1046ardb_sdcard_defconfig
2017-02-03 20:33:42 -05:00
Prabhakar Kushwaha
8e63ed518d arch: arm: update the IFC IP input clock
IFC IP clock is always a constant divisor of platform clock
pre-defined per SoC. Clock control register (CCR) used in
current implementation governs IFC IP output clock.

Update sys_info->freq_localbus to represent IFC input clock with
value constant divisor of platform clock.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-02-03 14:31:19 -08:00
Lukasz Majewski
11bd5e7b62 BOARD: MCCMON6: Provide support for iMX6q based mccmon6 board
This patch provides u-boot support for Liebherr (LWN) mccmon6 board.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-01-30 16:24:47 +01:00
Marcin Niestroj
d4b1b52737 ARM: imx6ul: Move liteSOM source to SoC directory
Moving arch/arm/mach-litesom/ to arch/arm/cpu/armv7/mx6/ was requested
in [1] during discussion of chiliSOM support patches.

[1] http://lists.denx.de/pipermail/u-boot/2017-January/279137.html

Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-01-27 10:48:07 +01:00
Simon Glass
a5d67547dd Convert CONFIG_BOARD_EARLY_INIT_F to Kconfig
This converts the following to Kconfig:
   CONFIG_BOARD_EARLY_INIT_F

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-01-25 17:38:32 -05:00
Tom Rini
e5ec48152a Kconfig: Migrate BOARD_LATE_INIT to a select
This option should not really be user selectable.  Note that on PowerPC
we currently only need BOARD_LATE_INIT when CHAIN_OF_TRUST is enabled so be
conditional on that.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> (for UniPhier)
2017-01-24 10:35:54 -05:00
Hou Zhiqiang
19538f306b kconfig: move FSL_PCIE_COMPAT to platform Kconfig
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:27:18 -08:00
York Sun
66e399b68d ddr: fsl: Move macro CONFIG_NUM_DDR_CONTROLLERS to Kconfig
Use option NUM_DDR_CONTROLLERS in ddr Kconfig and clean up existing
usage in ls102xa and fsl-layerscape. Remove all powerpc macros in
config header and board header files.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-01-04 19:40:49 -05:00
York Sun
ba1b6fb5cc arm: layerscape: Move CONFIG_SYS_FSL_ERRATUM_* to Kconfig
Use Kconfig to select errata workaround.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-01-04 19:40:42 -05:00
York Sun
d26e34c4c4 fsl_ddr: Move DDR config options to driver Kconfig
Create driver/ddr/fsl/Kconfig and move existing options. Clean up
existing macros.

Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate sbc8641d, xpedite537x and MPC8536DS, run a moveconfig.py -s]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-04 19:40:41 -05:00
York Sun
90b80386ff crypto: Move CONFIG_SYS_FSL_SEC_LE and _BE to Kconfig
Use Kconfig option to set little- or big-endian access to secure
boot and trust architecture.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-01-04 19:40:19 -05:00
York Sun
2c2e2c9e14 crypto: Move SYS_FSL_SEC_COMPAT into driver Kconfig
Instead of define CONFIG_SYS_FSL_SEC_COMPAT in header files for PowerPC
and ARM SoCs, move it to Kconfig under the driver.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-01-04 19:40:17 -05:00
Jagan Teki
854bb75be9 imx6: icorem6_rqs: Add FEC support
Add FEC support for Engicam i.CoreM6 RQS modules.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16 18:39:06 +01:00
Jagan Teki
bd363f80e4 imx6: geam6ul: Add FEC support
Add FEC support for Engicam GEAM6UL module.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16 18:39:05 +01:00
Jagan Teki
dca7c2878a imx6: icorem6_rqs: Add I2C support
Add I2C support for Engicam i.CoreM6 RQS modules.

icorem6qdl-rqs> i2c bus
Bus 0:  i2c@021a0000
Bus 1:  i2c@021a4000
Bus 2:  i2c@021a8000
icorem6qdl-rqs> i2c dev 0
Setting bus to 0
icorem6qdl-rqs> i2c speed 100000
Setting bus speed to 100000 Hz
icorem6qdl-rqs> i2c probe
Valid chip addresses: 4F
icorem6qdl-rqs> i2c md 4F 0xff
00ff: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff    ................
icorem6qdl-rqs> i2c bus
Bus 0:  i2c@021a0000  (active 0)
   4f: generic_4f, offset len 1, flags 0
Bus 1:  i2c@021a4000
Bus 2:  i2c@021a8000

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16 18:39:05 +01:00
Jagan Teki
871ec6da42 arm: imx6q: Add Engicam i.CoreM6 Quad/Dual RQS Starter Kit initial support
Boot from MMC:
-------------
U-Boot SPL 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:59:44)
Trying to boot from MMC1

U-Boot 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:59:44 +0530)

CPU:   Freescale i.MX6D rev1.2 at 792 MHz
Reset cause: POR
Model: Engicam i.CoreM6 Quad/Dual RQS Starter Kit
DRAM:  512 MiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
icorem6qdl-rqs>

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16 17:16:10 +01:00
Jagan Teki
d31373c4ac imx6: geam6ul: Add I2C support
Add I2C support for Engicam GEAM6UL module.

geam6ul> i2c bus
Bus 0:  i2c@021a0000
Bus 1:  i2c@021a4000
geam6ul> i2c dev 0
Setting bus to 0
geam6ul> i2c dev
Current bus is 0
geam6ul> i2c speed 100000
Setting bus speed to 100000 Hz
geam6ul> i2c probe
Valid chip addresses: 2C
geam6ul> i2c md 2C 0xff
00ff: 00 00 00 00 0f f0 01 64 ff ff 00 00 00 00 00 00    .......d........

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16 17:16:10 +01:00
Jagan Teki
a5b9f8c8f0 arm: imx6ul: Add Engicam GEAM6UL Starter Kit initial support
Boot Log:
--------
U-Boot SPL 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30)
Trying to boot from MMC1

U-Boot 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30 +0530)

CPU:   Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 43C
Reset cause: POR
Model: Engicam GEAM6UL
DRAM:  128 MiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
geam6ul>

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16 17:16:10 +01:00
Jagan Teki
d90384e834 imx6: icorem6: Add I2C support
Add I2C support for Engicam i.CoreM6 qdl board.

icorem6qdl> i2c bus
Bus 0:  i2c@021a0000
Bus 1:  i2c@021a4000
Bus 2:  i2c@021a8000
icorem6qdl> i2c dev 2
Setting bus to 2
icorem6qdl> i2c speed 100000
Setting bus speed to 100000 Hz
icorem6qdl> i2c probe
Valid chip addresses: 2C
icorem6qdl> i2c md 2C 0xff
00ff: 00 00 00 00 0f f0 01 64 ff ff 00 00 00 00 00 00    .......d........

Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Heiko Schocher <hs@denx.de>
2016-12-16 17:15:27 +01:00
Jagan Teki
e920f60779 icorem6: Use CONFIG_DM_ETH support
Use CONFIG_DM_ETH and remove board_eth_init code
from board files.

Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16 17:15:27 +01:00
Patrick Bruenn
98d62e618b arm: imx: add i.MX53 Beckhoff CX9020 Embedded PC
Add CX9020 board based on mx53loco.
Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse
serial_mxc with DTE and prepare for device tree migration of other
functions and imx53 devices.

The CX9020 differs from i.MX53 Quick Start Board by:
- use uart2 instead of uart1
- DVI-D connector instead of VGA
- no audio
- CCAT FPGA connected to emi
- enable rtc

Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
2016-12-16 12:57:12 +01:00
Peng Fan
47f73504d8 arm: imx: add i.MX6SLL EVK board support
Add i.MX6SLL EVK board support.
1. Add imx6sll-evk device tree.
2. Enable SDHC/I2C/UART.
3. Enable REGULATOR/PMIC/I2C/GPIO/SDHC/PINCTRL driver.

Boot Log:
U-Boot 2016.11-00127-gc635871-dirty (Nov 24 2016 - 13:28:19 +0800)

CPU:   Freescale i.MX6SLL rev1.0 at 792MHz
CPU:   Commercial temperature grade (0C to 95C)Reset cause: POR
Model: Freescale i.MX6SLL EVK Board
Board: MX6SLL EVK
DRAM:  2 GiB
i2c bus 0 at 35258368, no gpio pinctrl state.
PMIC: PFUZE100! DEV_ID=0x10 REV_ID=0x21
MMC:   FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-12-16 11:38:24 +01:00
Peng Fan
2cc021697b imx: mx6sll: add Kconfig entry for i.MX6SLL
add Kconfig entry for i.MX6SLL

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-12-16 11:38:24 +01:00
Peng Fan
dfca246f4c imx: mx6sll: add clock support
Add clock support for i.MX6SLL.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-12-16 11:38:24 +01:00
Peng Fan
708f692753 imx: clock: gate clk before changing pix clk mux
The LCDIF Pixel clock mux is not glitchless, so need
to gate before changing mux.

Also change enable_lcdif_clock prototype with a new input
parameter to indicate disable or enable.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-12-16 11:38:24 +01:00
Peng Fan
e332623b03 imx: mx6sl: add lcdif clock support
Add lcdif clock support for i.MX6SL.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-12-16 11:38:24 +01:00
Peng Fan
70ac169723 imx: mx6: lcdif: gate clock before changing mux
The mux for the lcd clock is not glitchless,
so need to first gate the clock before changing the mux.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-12-16 11:38:24 +01:00
Peng Fan
0e81982de0 imx: mx6: fix mmdc ch0 clk for 6SL
>From RM, per_periph2_clk_sel option3 is:
"derive clock from 198MHz clock (divided 392MHz PLL2 PFD)."

So fix it.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-12-16 11:38:24 +01:00
Marcin Niestroj
c9e40e65e1 board/liteboard: Add support for liteBoard
liteBoard is a development board which uses liteSOM as its base.

Hardware specification:
 * liteSOM (i.MX6UL, DRAM, eMMC)
 * Ethernet PHY (id 0)
 * USB host (usb_otg1)
 * MicroSD slot (uSDHC1)

Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
2016-12-16 10:31:13 +01:00
Breno Lima
0719b16f19 udoo_neo: Add thermal support
Add thermal support on the Kconfig file.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-12-16 10:21:25 +01:00
Breno Lima
4a056c4504 udoo_neo: Move MX6SX configuration to Kconfig
It's not necessary to define the processor in the defconfig file.

The preferred method to select the SoC is via Kconfig file.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-12-16 10:20:10 +01:00
Max Krummenacher
a02d517b01 arm: imx: initial support for colibri imx6
This adds board support for the Toradex module family Colibri iMX6.
The familiy consists of a module with i.MX6 DualLite, i.MX6 Solo, both
with a version for commercial and industrial temperature range.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
2016-12-16 10:03:43 +01:00
Max Krummenacher
592f4aed6d arm: imx: initial support for apalis imx6
This adds board support for the Toradex module family Apalis iMX6.
The familiy consists of a module with i.MX6 Dual, i.MX6 Quad with
commercial and industrial temperature range.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
2016-12-16 10:02:45 +01:00
Patrick Delaunay
91558c8153 arm: armv7: add us timer for bootstage
solve issue when bootstage is used with armV7 generic timer
first call of timer_get_boot_us() use the function get_timer()
before timer initialization (arch.timer_rate_hz = 0)
=> div by 0

Commit-notes

When I activate bootstage on ARMV7 architecture with platform
using the generic armv7 timer defined in file
./arch/arm/cpu/armv7m/timer.c

I have a issue because gd->arch.timer_rate_hz = 0

For me the get_timer() function should not used before timer_init
(which initialize gd->arch.timer_rate_hz) at least for the ARMV7
timer.

But in the init sequence, the first bootstage fucntion is called
before timer_init and this function use the timer function.

For me it is a error in the generic init sequence :
mark_bootstage is called before timer_init.

static init_fnc_t init_sequence_f[] = {
....
    arch_cpu_init_dm,
    mark_bootstage,        /* need timer, go after init dm */
...
#if defined(CONFIG_ARM) || defined(CONFIG_MIPS) || \
        defined(CONFIG_BLACKFIN) || defined(CONFIG_NDS32) || \
        defined(CONFIG_SPARC)
    timer_init,        /* initialize timer */
#endif
.......

To solve the issue for all the paltform, we can move timer_init()
call just before mark_bootstage() in this array...

It should be ok for ARMV7 but I don't sure for other platform
impacted
- the other ARM platform or ARMV7 wich don't use generic timer
- MIPS BLACKFIN NDS32 or SPARC

and I don't sure of impact for other function called
(board_early_init_f for example....)

=> This patch solve issue only in timer armv7
   get_boot_us() can be called everytime without div by 0 issue
   (gd->arch.timer_rate_hz is not used)

END

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
2016-12-09 08:39:10 -05:00
Tom Rini
194eded14c Merge git://git.denx.de/u-boot-mpc85xx 2016-12-04 13:55:15 -05:00
York Sun
72ccd31e64 armv7: ls1021a: Move SECURE_BOOT option to Kconfig
Move from CONFIG_SYS_EXTRA_OPTIONS to Kconfig option.

Signed-off-by: York Sun <york.sun@nxp.com>
2016-12-02 12:38:41 -08:00