- device-tree sync-up with Linux for ls1028a
- fixes/update in fsl-ddr driver, fsl-validate, lx2162a, fsl-mc,
spintable code, configs, qspi node, pci
- enable EFI_SET_TIME support in sl28
- powerpc: Drop -mstring
Header file mach/cpu.h already defines MBUS_PCI_MEM_SIZE macro which
defines size of MBUS_PCI_MEM_BASE window. So use global MBUS_PCI_MEM_SIZE
macro instead of locally defined PCIE_MEM_SIZE macro. Both macros have same
definition.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
In the current code, it doesn't reset the cursors of LUT entry and
StreamID at the beginning of the fixup, so it can result in LUT entry
setup and msi-map mismatch and LUT entries and StreamID leaking
when reload and fixup the DTB.
This patch move the initialization of LUT entry and StreamID cursors
to the beginning of the fixup to resolve the issues.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The official bindind of the PCIe controller of the ls1028a has the
following compatible string:
compatible = "fsl,ls1028a-pcie";
Additionally, the resource names and count are different. Update the
driver to support this binding and change the entry in the ls1028a
device tree.
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
According to the Armada 3720 Functional Specification Data Strobe applies
for both read and write config requests.
Data strobe bits configure which bytes from the start address should be
returned for read request. Set value 0xf (all 4 bits) into Data Strobe
register to read all four bytes from specified 32-bit config space
register. Same value for Data Strobe register is programmed by Linux
pci-aardvark.c driver for config read requests.
Without this patch pci-aardvark driver sets data strobe register only
during config write operations. So any followup config read operations
could result with just partial datai returned (if previous write operation
was not 32-bit wide). This patch fixes it and ensures that config read
operations always read all bytes from requested register.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This is a pci driver, not an eth driver.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Root Complex should be the default mode, let's set it explicitly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that PCI Bridge is working, U-Boot's CONFIG_PCI_PNP code automatically
enables memory access and bus mastering when it is needed. So do not
prematurely enable memory access and bus mastering.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
PCI Bridge is always accessible also when link is down. So move detection
of link up from mvebu_pcie_of_to_plat() function to mvebu_pcie_valid_addr()
function which is used when accessing PCI config space.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Functions mvebu_pcie_get_local_bus_nr() and mvebu_pcie_get_local_dev_nr()
are not used, so remove them.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The mysterious "Memory controller" PCI device which is present in PCI
config space is improperly configured and crippled PCI Bridge which acts
as PCIe Root Port for endpoint PCIe card.
This PCI Bridge reports in PCI config space incorrect Class Code (Memory
Controller) and incorrect Header Type (Type 0). It looks like HW bug in
mvebu PCIe controller but apparently it can be changed via mvebu registers
to correct values.
The worst thing is that this PCI Bridge is crippled and its PCI config
registers in range 0x10-0x34 alias access to internal mvebu registers which
have different functionality as PCI Bridge registers. Moreover,
configuration of PCI primary and secondary bus numbers (registers 0x18
and 0x19) is done via totally different mvebu registers via totally strange
method and cannot be done via PCI Bridge config space.
Due to above fact about PCI config range 0x10-0x34, allocate a private
cfgcache[] buffer in the driver, to which PCI config access requests to
the 0x10-0x34 space will be redirected in mvebu_pcie_read_config() and
mvebu_pcie_write_config() functions. Function mvebu_pcie_write_config()
will also catch writes to PCI_PRIMARY_BUS (0x18) and PCI_SECONDARY_BUS
(0x19) registers and set PCI Bridge primary and secondary bus numbers via
mvebu's own method.
Also, Expansion ROM Base Address register (0x38) is available, but at
different offset 0x30. So recalculate register offset before accessing PCI
config space.
After these steps U-Boot sees working PCI Bridge and CONFIG_PCI_PNP code
can finally start enumerating all PCIe devices correctly, even with more
complicated PCI topology. So update also mvebu_pcie_valid_addr() function
to reflect state of the real device topology.
Each PCIe port is de-facto isolated and every PCI Bridge which is part of
PCIe Root Complex is also isolated, so put them on separate PCI buses as
(local) device 0.
U-Boot already supports enumerating separate PCI buses, real (HW) bus
number can be retrieved by "PCI_BUS(bdf) - dev_seq(bus)" code, so update
config read/write functions to properly handle more complicated tree
topologies (e.g. when a PCIe switch with multiple PCI buses is connected
to the PCIe port).
Local bus number and local device number on mvebu are used for determining
which config request type is used (Type 0 vs Type 1). On normal non-broken
PCIe hardware it is done by primary and secondary bus numbers. So correctly
translate settings between these numbers to ensure that correct config
requests are sent over the PCIe bus.
As bus numbers are correctly re-configured, it does not make sense to print
some initial bogus configuration during probe, so remove this debug code.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
When reading 8 or 16 bits from config space, use appropriate readb() or
readw() calls. This ensures that PCIe controller does not read more bits
from endpoint card as asked by read_config() function.
Technically there should not be an issue with reading data from config
space which are not later used as there are no clear-by-read registers.
But it is better to use correct read operation based on requested size.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Current implementation of write_config() is broken for PCI_SIZE_8 or
PCI_SIZE_16 as it always uses writel(), which means that write operation
is always 32-bit, so upper 24 bits for PCI_SIZE_8 and upper 16 bits for
PCI_SIZE_16 are cleared.
Fix this by using writeb() and writew(), respectively.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
As stated in comment above the code, CRS response can be returned to OS
only for 4-byte PCI_VENDOR_ID config read request. So fix the code.
Fixes: 1d7ad68559 ("arm: a37xx: pci: Handle propagation of CRSSVE bit from PCIe Root Port")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
PCI Bridge which represents Aardvark PCIe Root Port does not have
configurable bars.
So ensure that write operation to bars registers on PCI Bridge is noop and
bars registers always contain zero address which indicates that bars are
unsupported.
After this change U-Boot 'pci bar 0.0.0' command does not show any
allocated bars for PCI Bridge device.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: cb056005dc ("arm: a37xx: pci: Add support for accessing PCI Bridge on root bus")
Reviewed-by: Stefan Roese <sr@denx.de>
Function dm_pci_hose_probe_bus() expects that bus is valid PCI device with
Bridge header type (0x01). So add check before touching PCI config space to
prevent misconfiguring some non-standard device.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
PCI Rom Address is currently supported only for Normal (0x00) and
Bridge (0x01) header types. Fix code accordingly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
There were several changes for this structure but the documentation was
not changed at the time. Fix this.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that PCI Bridge (PCIe Root Port) for Aardvark is emulated in U-Boot,
add support for handling and propagation of CRSSVE bit.
When CRSSVE bit is unset (default), driver has to reissue config
read/write request on CRS response.
CRSSVE bit is supported only when CRSVIS bit is provided in read-only
Root Capabilities register. So manually inject this CRSVIS bit into read
response for that register.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that PCI Bridge is working for the PCIe Root Port, U-Boot's PCI_PNP
code automatically enables memory access and bus mastering when needed.
We do not need to enable it when setting the HW up.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Aardvark does not have a real PCIe Root Port device on the root bus.
Instead it has PCIe registers of PCIe Root Port device mapped in
internal Aardvark memory space starting at offset 0xc0.
The PCIe Root Port itself is normally available as a PCI Bridge device
on the root bus with bus number zero. Aardvark instead has the
configuration registers of this PCI Bridge at offset 0x00 of Aardvark's
memory space, but the class code of this device is Mass Storage
Controller (0x010400), instead of PCI Bridge (0x600400), which causes
U-Boot to fail to recognize it as a P2P Bridge
Add a hook into the pcie_advk_read_config() / pcie_advk_write_config()
functions to redirect access for root bus from PIO transfer to this
internal Aardvark memory space. This will allow U-Boot to access
configuration space of this PCI Bridge which represents PCIe Root Port.
Redirect access to PCI Bridge registers in range 0x10 - 0x34 to driver's
internal buffer (cfgcache[]). This is because at those addresses
Aardvark has different registers, incompatible with config space of a
PCI Bridge.
Redirect access to PCI Bridge register PCI_ROM_ADDRESS1 (0x38) to
Aardvark internal address for that register (0x30).
When reading PCI Bridge register PCI_HEADER_TYPE, set it explicitly to
value Type 1 (PCI_HEADER_TYPE_BRIDGE) as PCI Bridge must be of Type 1.
When writing to PCI_PRIMARY_BUS or PCI_SECONDARY_BUS registers on this
PCI Bridge, correctly update driver's first_busno and sec_busno
variables, so that pcie_advk_addr_valid() function can check if address
of any device behind the root bus is valid and that PIO transfers are
started with correct config type (1 vs 0), which is required for
accessing devices behind some PCI bridge after the root bus.
U-Boot's PCI_PNP code sets primary and secondary bus numbers as relative
to the configured bus number of the root bus. This is done so that
U-Boot can support multiple PCIe host bridges or multiple root port
buses, when internal bus numbers are different.
Now that root bus is available, update code in pcie_advk_read_config()
and pcie_advk_write_config() functions to correctly calculate real
Aardvark bus number of the target device from U-Boot's bus number as:
busno = PCI_BUS(bdf) - dev_seq(bus)
Stefan: Small fix of header masking as suggested by Pali.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Aardvark reports Disabled and Hot Reset LTSSM states as values >= 0x20.
Link is not up in these states, so fix pcie_advk_link_up() function.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
On Amlogic A311D, when the PCIe link fails disabling the related clocks
makes USB fail. For an unknown reason, this doesn happen on the S905D3 SoC.
Mimic the Linux behavior by not considering a link failure a probe failure,
and continue even if the PCIe link is down.
Reported-by: Art Nikpal <email2tema@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To avoid W=1 build warnings, declare this function as static, since it
is not used outside of this translation module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The function prototype for ft_pci_setup is inside fdt_support.h, we need
to include that header.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To avoid W=1 build warnings, declare this function as static, since it
is not used outside of this translation module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To avoid W=1 build warnings, declare this function as static, since it
is not used outside of this translation module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To avoid W=1 build warnings, declare this function as static, since it
is not used outside of this translation module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To avoid W=1 build warnings, declare this function as static, since it
is not used outside of this translation module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To avoid a build warning with W=1, provide a function prototype for
dm_pciauto_prescan_setup_bridge, which is a non-static function whose
definition is inside pci_auto.c.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some PCIe controller's read_config() method support indicating error
directly via return value, but some cannot distinguish all-ones (or
all-zeros) read response from an error.
The current code in pci_bind_bus_devices() interprets all-ones /
all-zeros in PCI_VENDOR_ID register as "nothing connected", and
continues the cycle, but an error returned via return value breaks the
cycle.
This is wrong for the PCIe controllers which return this error via
return value.
Handle all errors when reading PCI_VENDOR_ID the same way.
This fixes enumeration of PCI devices for example when there is a PCI
bridge connected behind another PCI bridge and not all ports are
connected to a device, and the controller (for example Aardvark)
translates the UR error (Unsupported Request) as -EOPNOTSUPP.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Lower 4 bits of PCI_MEMORY_BASE and PCI_MEMORY_LIMIT registers are reserved
and should be zero. So do not set them to non-zero value.
Lower 4 bits of PCI_PREF_MEMORY_BASE and PCI_PREF_MEMORY_LIMIT registers
contain information if 64-bit memory addressing is supported. So preserve
this information when overwriting these registers.
Lower 4 bits of PCI_IO_BASE and PCI_IO_LIMIT register contain information
if 32-bit io addressing is supported. So preserve this information and do
not try to configure 32-bit io addressing (via PCI_IO_BASE_UPPER16 and
PCI_IO_LIMIT_UPPER16 registers) when it is unsupported.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
With legacy PCI code removed and thus DM_PCI also removed, a few places
did not get correctly updated with the merge to next and thus broke.
Remove now extraneous dependencies on DM_PCI.
Signed-off-by: Tom Rini <trini@konsulko.com>
Use dev_dbg() instead of dev_err() in pcie_advk_check_pio_status().
For example CRS is not an error status, it just says that the request
should be retried.
Without this, U-Boot spams the terminal with
pcie_advk pcie@d0070000: Non-posted PIO Response Status: UR, 0xc80 @ 0x100000
pcie_advk pcie@d0070000: Non-posted PIO Response Status: UR, 0xc80 @ 0x108000
pcie_advk pcie@d0070000: Non-posted PIO Response Status: UR, 0xc80 @ 0x110000
pcie_advk pcie@d0070000: Non-posted PIO Response Status: UR, 0xc80 @ 0x120000
pcie_advk pcie@d0070000: Non-posted PIO Response Status: UR, 0xc80 @ 0x128000
pcie_advk pcie@d0070000: Non-posted PIO Response Status: UR, 0xc80 @ 0x130000
...
when a device is not connected to a PCIe switch (Unsupported Request
from the switch).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
According to PCIe base specification, if CRS Software Visibility is not
enabled, the Root Complex must re-issue the Configuration Request as a new
Request.
Normally this part of Root Complex is implemented in hardware but aardvark
is somehow special and does not implement it in hardware and expect that
handling of config requests are fully implemented in software.
This re-issuing functionality is required also because U-Boot does not
support CRS Software Visibility feature and therefore expects that Root
Complex re-issues requests as is specified in PCIe base specification.
Retry / re-issue config request up to the PIO_MAX_RETRIES, to prevent
infinite loop. After retry count exceed PIO_MAX_RETRIES, returns failure.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
There was mistake in commit 4cd61c43fd ("arm: a37xx: pci: Fix handling
PIO config error responses"). U-Boot does not support handling of CRS
return value for PCI_VENDOR_ID config read request and also does not set
CRSSVE bit.
Therefore disable returning CRS response for now.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 4cd61c43fd ("arm: a37xx: pci: Fix handling PIO config error responses")
Reviewed-by: Stefan Roese <sr@denx.de>
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
Returning fabricated CRS value (0xFFFF0001) by PCIe Root Complex to OS is
allowed only for 4-byte PCI_VENDOR_ID config read request and only when
CRSSVE bit in Root Port PCIe device is enabled. In all other error PCIe
Root Complex must return all-ones.
So implement this logic in pci-aardvark.c driver properly.
aardvark HW does not have Root Port PCIe device and U-Boot does not
implement emulation of this device. So expect that CRSSVE bit is set as
U-Boot can already handle CRS value for PCI_VENDOR_ID config read request.
More callers of pci_bus_read_config() function in U-Boot do not check for
return value, but check readback value. Therefore always fill readback
value in pcie_advk_read_config() function. On error fill all-ones of
correct size as it is required for PCIe Root Complex.
And also correctly propagates error from failed config write request to
return value of pcie_advk_write_config() function. Most U-Boot callers
ignores this return value, but it is a good idea to return correct value
from function.
These issues about return value of failed config read requests, including
special handling of CRS were reported by Lorenzo and Bjorn for Linux kernel
driver pci-aardvark together with quotes from PCIe r4.0 spec, see details:
https://lore.kernel.org/linux-pci/20210624213345.3617-1-pali@kernel.org/t/#u
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This driver is currently only used on MIPS Malta boards.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver is currently only used on MIPS Malta boards.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On MIPS the DRAM start address respectively CONFIG_SYS_SDRAM_BASE
is still used as a virtual, CPU-mapped address instead of being used
as physical address. Converting all MIPS boards and generic MIPS code
to fix that is not trivial. Due to the approaching deadline for
PCI DM conversion, this workaround is required for MIPS boards with
PCI support until the CONFIG_SYS_SDRAM_BASE issue could be solved.
Add a compile-time option to let the PCI uclass core optionally map
the DRAM address to a physical address when adding the PCI region
of type PCI_REGION_SYS_MEMORY.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
At present only bridge devices are bound before relocation, to save space
in pre-relocation memory. In some cases we do actually want to bind a
device, e.g. because it provides the console UART. Add a devicetree
binding to support this.
Use the PCI_VENDEV() macro to encode the cell value. This is present in
U-Boot but not used, so move it to the binding header-file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These functions don't modify the device-ID struct that is passed in, so
mark the argument as const, so the data structure can be declared that
way. This allows it to be placed in the rodata section.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Remapped address of PCIe outbound window may have set only bits from the
mask. Add additional check that remapped address which is calculated from
PCIe bus address specified in DTS file is valid.
Remove also useless clearing of low 16 bits in win_mask. As win_size is
power of two and is at least 0x10000 it means that it always has zero low
16 bits.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add PCIe driver for UniPhier SoCs. This PCIe controller is based on
Synopsys DesignWare Core IP.
This version doesn't apply common DW functions because supported
controller doesn't have unroll version of iATU.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
If reset-gpio is defined by device-tree use that if
CONFIG_PCIE_IMX_PERST_GPIO is not defined.
Note that after this the following boards which define
CONFIG_PCIE_IMX_PERST_GPIO in their board header file as well as their
device-tree should be able to remove CONFIG_PCIE_IMX_PERST_GPIO without
consequence:
- mx6sabresd
- mx6sxsabresd
- novena
- tbs2910
- vining_2000
Note that the ge_bx50v3 board uses CONFIG_PCIE_IMX_PERST_GPIO and does
not have reset-gpios defined it it's pcie node in the dt thus removing
CONFIG_PCIE_IMX_PERST_GPIO globally can't be done until that board adds
reset-gpios.
Cc: Ian Ray <ian.ray@ge.com> (maintainer:GE BX50V3 BOARD)
Cc: Sebastian Reichel <sebastian.reichel@collabora.com> (maintainer:GE BX50V3 BOARD)
Cc: Fabio Estevam <festevam@gmail.com> (maintainer:MX6SABRESD BOARD)
Cc: Marek Vasut <marex@denx.de> (maintainer:NOVENA BOARD)
Cc: Soeren Moch <smoch@web.de> (maintainer:TBS2910 BOARD)
Cc: Silvio Fricke <open-source@softing.de> (maintainer:VINING_2000 BOARD)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add ECAM based SynQuacer PCIe RC driver. This driver configures the
PCIe RC and filter out a ghost pcie config.
Since the Linux kernel expects "socionext,synquacer-pcie-ecam" device
is configured by firmware (EDK2), it doesn't re-configure in the kernel.
So as same as EDK2, U-Boot needs to configure it before boot the kernel.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Define LOG_CATEGORY for all uclass to allow filtering with
log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace msleep occurences by udelay.
drivers/pci/pcie_dw_rockchip.c:254:3: warning: implicit
declaration of function 'msleep' [-Wimplicit-function-declaration]
Cc: Patrick Wildt <patrick@blueri.se>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Use the generic error number instead of specific error number.
Changes fix the below error.
drivers/pci/pcie_dw_rockchip.c: In function 'rk_pcie_read':
drivers/pci/pcie_dw_rockchip.c:70:10: error: 'PCIBIOS_UNSUPPORTED'
undeclared (first use in this function)
70 | return PCIBIOS_UNSUPPORTED;
| ^~~~~~~~~~~~~~~~~~~
drivers/pci/pcie_dw_rockchip.c: In function 'rk_pcie_write':
drivers/pci/pcie_dw_rockchip.c:90:10: error: 'PCIBIOS_UNSUPPORTED'
undeclared (first use in this function)
90 | return PCIBIOS_UNSUPPORTED;
| ^~~~~~~~~~~~~~~~~~~
Cc: Patrick Wildt <patrick@blueri.se>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Stop to initialize the PCIe controller if it's disabled by RCW.
Fixes: 118e58e26e ("pci: layerscape: Split the EP and RC driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The `ranges` DT property of the PCIe node is currently ignored by
Aardvark driver - all entries are used as transparent PCIe MEM, despite
some of them being defined for IO in DT.
This is because the driver does not setup PCIe outbound windows and thus
a default configuration is used.
This can cause an external abort on CPU when a device driver tries to
access non-MEM space.
Setup the PCIe windows according to the `ranges` property for all
non-MEM resources (currently only IO) and also non-transparent MEM
resources.
Because Linux expects that bootloader does not setup Aardvark PCIe
windows, disable them before booting Linux.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Change DT compatible string for A3700 PCIe from 'marvell,armada-37xx-pcie'
to 'marvell,armada-3700-pcie' to make U-Boot A3700 PCIe DT node compatible
with Linux' DT node.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Disable Root Bridge I/O space, memory space and bus mastering in Aardvark's
remove method, which is called before booting Linux kernel.
This ensures that PCIe device which was initialized and used by U-Boot
cannot do new DMA transfers until Linux initializes PCI subsystem and loads
appropriate drivers for the device.
During initialization of PCI subsystem Linux in fact disables this bus
mastering on Root Bridge (and later enables it when driver is loaded and
configured), but there is a possibility of a small window after U-Boot
boots Linux when bus mastering is enabled, which is not correct.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
During our debugging of the Aardvark driver in Linux we have discovered
that the PCIE_CORE_LINK_CTRL_STAT_REG register in fact controls standard
PCIe Link Control Register for PCIe Root Bridge. This led us to discover
that the name of the PCIE_CORE_LINK_TRAINING macro and the corresponding
comment by this macro's usage is misleading; this bit in fact controls
Retrain Link, which, according to PCIe base spec is defined as:
A write of 1b to this bit initiates Link retraining by directing the
Physical Layer LTSSM to the Recovery state. If the LTSSM is already in
Recovery or Configuration, re-entering Recovery is permitted but not
required.
Entering Recovery state is normally done from LTSSM L0, L0s and L1 states.
But since the pci-aardvark.c driver enables Link Training just a few lines
above, the controller is not in L0 ready state yet. So setting aardvark bit
PCIE_CORE_LINK_TRAINING does not actually enter Recovery state at this
place.
Moreover, trying to enter LTSSM Recovery state without other configuration
is causing issues for some cards (e.g. Atheros AR9xxx and QCA9xxx). Since
Recovery state is not entered, these issues are not triggered.
Remove code which tries to enter LTSSM Recovery state completely.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Fix compilation error when Werror is turned on. The warning could
possible break some CI builds.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add pcie driver for SiFive fu740, the driver depends on
fu740 gpio, clk and reset driver to do init. Force running at Gen1
for better capatible enumeration.
Several devices are tested:
a) M.2 NVMe SSD
b) USB-to-PCI adapter
c) Ethernet adapter (E1000 compatible)
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
The pcie_dw_mvebu configure ATU regions for memory, configuration
and IO space types. However the latter is not obligatory
and when not specified in the device tree, causes wrong
ATU configuration. Fix that by adding a dependency on the
detected PCIE regions count.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-on: https://sj1git1.cavium.com/18136
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Tested-by: Kostya Porotchkin <kostap@marvell.com>
commit 6ecbe13756 ("drivers: pci: imx: add imx_pcie_remove function")
attempted to resolve an issue caused by MX6QDL not having a proper
intneral PCIe core reset and thus hanging during kernel init if the
bootloader had enabled PCI.
The issue exists for IMX6Q, IMX6D, IXM6S, and IMX6DL. Fix the case for
IMX6S and IMX6DL getting missed.
This fixes IMX6S and IMX6DL with PCI enabled in U-Boot booting for
Linux v4.11+.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Update the highest subordinate bus number after probing the devices
under the bus for setting up the bridge correctly.
The commit 42f3663a3f ("pci: Update to use new sequence numbers")
removed this but it is required if a PCIe bridge is under the bus.
Fixes: 42f3663a3f ("pci: Update to use new sequence numbers")
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Trying to clear PIO_START register when it is non-zero (which indicates
that previous PIO transfer has not finished yet) causes an External
Abort with SError 0xbf000002.
This bug is currently worked around in TF-A by handling External Aborts
in EL3 and ignoring this particular SError.
This workaround was also discussed at:
https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/commit/?id=3c7dcdac5c50https://lore.kernel.org/linux-pci/20190316161243.29517-1-repk@triplefau.lt/https://lore.kernel.org/linux-pci/971be151d24312cc533989a64bd454b4@www.loen.fr/https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/1541
Implement a proper fix to prevent this External Abort. As it is not
possible to cancel a pending PIO transfer, simply do not start a new one
if previous has not finished yet. In this case return an error to the
caller.
In most cases this SError happens when there is no PCIe card connected
or when PCIe link is down. The reason is that in these cases a PIO
transfer takes about 1.44 seconds. For this reason we also increase the
wait timeout in pcie_advk_wait_pio() to 1.5 seconds.
If PIO read transfer for PCI_VENDOR_ID register times out, or if it
isn't possible to read it yet because previous transfer is not finished,
return Completion Retry Status value instead of failing, to give the
caller a chance to send a new read request.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch adds the PCIe host controller driver for MIPS Octeon II/III.
The driver mainly consist of the PCI config functions, as all of the
complex serdes related port / lane setup, is done in the serdes / pcie
code available in the "arch/mips/mach-octeon" directory.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add support for the DW PCIe controller found in the Amlogic Meson AXG and
G12 (G12A, G12B, SM1) SoCs.
This uses the common DW PCIe helpers introducted previously.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
With the introduction of pcie_dw_rockchip, and need to support the DW PCIe in the
Amlogic AXG & G12 SoCs, most of the DW PCIe helpers would be duplicated.
This introduce a "common" DW PCIe helpers file with common code merged from the
dw_ti and dw_rockchip drivers and adapted to fit with the upcoming dw_meson.
The following changes will switch the dw_ti and dw_rockchip to use these helpers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Green Wan <green.wan@sifive.com>
[bmeng: remove the blank line at EOF of drivers/pci/pcie_dw_common.c]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
The copy buffer, if enabled, prevents booting from coreboot correctly,
since no memory is allocated for it. Allow it to fall back to disabled
in this situation. This ensures that a console is displayed, even if
it is slow.
Signed-off-by: Simon Glass <sjg@chromium.org>
As on some incipient Layerscape platforms (LS1043A series) there isn't
separate PF control register block, these registers reside in the LUT
register block, so when the driver detected there isn't 'ctrl', it will
assign the 'lut' address to the ls_pcie->ctrl.
The current code allocate memory for the struct ls_pcie with random
contents, this can result in skipping to assign the ls_pcie->ctrl with
the 'lut' address, then further crash with the incorrect address.
Fixes: 118e58e26e ("pci: layerscape: Split the EP and RC driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Marvell Armada 3720 Functional Errata, Guidelines, and Restrictions
document describes in erratum 4.1 PCIe value of vendor ID (Ref #: 243):
The readback value of VEND_ID (RD0070000h [15:0]) is 1B4Bh, while it
should read 11ABh.
The firmware can write the correct value, 11ABh, through VEND_ID
(RD0076044h [15:0]).
Implement this workaround in U-Boot PCIe controller driver aardvark for
both PCI vendor id and PCI subsystem vendor id.
This change affects PCI vendor id of PCIe root bridge emulated by Linux
kernel. With this change Linux kernel reports correct vendor id 11AB.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
At present the driver only supports 32-bit bus and cpu address.
The controller's outbound registers/fields for extended address
are not programmed. Let's program them to support 64-bit bus and
cpu address.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
devfdt_get_addr_index() returns fdt_addr_t which might be a 64-bit
physical address. Use map_physmem() to return the virtual address
that can be used by a 32-bit machine.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
For the QEMU ppce500 machine, LAW registers are not implemented
hence CONFIG_FSL_LAW is not turned on and all LAW APIs are not
available. We should wrap all LAW registers programming in the
mpc85xx PCI driver with CONFIG_FSL_LAW.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Commit e002474158 ("pci: pci-uclass: Dynamically allocate the PCI regions")
changes 'struct pci_controller'.regions from pre-allocated array of
regions to dynamically allocated, which unfortunately broken lots of
boards that still use the non-DM PCI driver.
This patch changes the non-DM fsl_pci_init driver to dynamically
allocate the regions, just like what's done in the pci uclass driver.
Fixes: e002474158 ("pci: pci-uclass: Dynamically allocate the PCI regions")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Linux displays the real PCIe card connected to a mvebu PCIe slot as
device 0, not 1. This is done by setting local dev number to 1, so that
the local "Marvell Memory controller" device is on address 1.
Let's do it also in U-Boot.
With this commit the pci command in U-Boot prints something like:
=> pci
Scanning PCI devices on bus 0
BusDevFun VendorId DeviceId Device Class Sub-Class
_____________________________________________________________
00.00.00 0x168c 0x003c Network controller 0x80
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Refactor validation of bdf parameter in mvebu_pcie_read/write_config
functions.
We can simplify the code by putting the validation into separate
function.
Also there are always only two devices visible on local bus:
* on slot configured by function mvebu_pcie_set_local_dev_nr()
(by default this register is set to 0) there is a
"Marvell Memory controller", which isn't useful in root complex
mode,
* on all other slots the real PCIe card connected to the PCIe slot.
We can simplify the code even more by simply allowing access only to
the real PCIe card.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Other drivers (aardvark, intel_fpga) print "(addr,size,val)" when
debugging is enabled. Print size for pci_mvebu as well.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Write bdf address in a same way in mvebu_pcie_read/write_config.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
PCI uclass maps PCI bus numbers to the seq member of struct udevice.
Use dev_seq(dev) as the bus number in mvebu_pcie_probe instead of an
incrementing a static variable.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Fix usage of VL805 XHCI PCIe controller when it is connected via PCIe to
Armada 3720 SOC. Without this U-Boot crashes when trying to access
enumerated USB devices connected to this XHCI PCIe controller.
This should be done according to the PCIe Link Initialization sequence, as
defined in Marvell Armada 3720 Functional Specification.
Linux has this code too.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Because the first PCIExAR(n) register is configured with the mapping,
It is the second PCIExAR(n) register that must be written with 0, not
the last one. Update the n from 4 to 1 to select the correct register.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Both the map address and mask must be power of two per documentation,
adjust the code accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add code to access the PCIe root bus space and configure it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
So far we've assumed a fixed configuration for inbound windows as we had
a single user for this controller. But the controller's DMA constraints
were improved starting with BCM2711's B1 revision of the SoC, notably
available in CM4 and Pi400. They allow for wider inbound windows. We can
now cover the whole address space, whereas before we where limited to
the lower 3GB.
This information is passed to us through DT's 'dma-ranges' property and
it's specially important for us to honor it since some interactions with
the board's co-processor assume we're doing so (specifically the XHCI
firmware load operation, which is handled by the co-processor after
u-boot has correctly configured the PCIe controller).
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Make sure we handover the PCIe controller in a clean state. Some of the
devices hanging from the PCIe bus might need to be properly reset
through #PERST in order for Linux to be able to initialize them.
This is specially important in order to properly initialize Raspberry Pi
4 B and 400's USB chip.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
- Espressobin: Set default env values at runtime (Pali)
- Espressobin: Set the maximum slave SPI speed to 40MHz (Pali)
- theadorable: PCIe test code enhancement and early deemphasis
enabling (Stefan)
- pci_mvebu: Disable config access to PCI host bridge ports (Stefan)
- mv_sdhci: parse device-tree entry (Baruch)
LX2162A is not like LX2160A which has different PCIe controller
in rev1 and rev2 silicon. It supports only one configuration of
PCIe controller, which is same as LS2088A. So update PCIe
compatible string same as LS2088A.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Tested-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch moves the SVR definitions to a new svr.h for
Layerscape armv7 and armv8 platforms respectively, so that
the PCIe driver can reuse them.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch changes the PCI config routines in the Armada XP / 38x driver
to not allow access to the PCIe root ports.
While updating the Armada XP based theadorable to the latest mainline
and testing it with the DM PCI driver I noticed, that the PCI root
bridge was being configured incorrectly. Resulting in the PCIe Intel
WiFi was not working correctly in Linux. With this patch applied, all
PCIe devices work without any issues in Linux again.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch completely removes CONFIG_PCI_ENUM_ONLY from the PCI code as
it is not configured for any board (any more). With this removal, some
PCI related files get cleaned up a bit.
Additional, dm_pciauto_setup_device() is now static, as it's not
referenced from any code outside of this C file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Value pcie->dev in function pcie_advk_probe() is not initialized yet
so use dev as argument for dev_dbg()/dev_warn().
Function pcie_advk_wait_pio() itself prints error message on failure
so do not print duplicate error message in caller.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Configure an IO region and window for PNP identical to how MEM region is
set up. Linux does this only if the DT defines a pcie-io-aperture
property for the SOC, but since all supported boards do this should not
be needed.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
On my DS414, some PCI devices return odd values when probing BAR sizes.
An obvious case is all-ones response, the Linux driver
(drivers/pci/probe.c) catches those explicitly and a comment explains
that either bit 0 or bit 1 must be clear (depending on MEM or IO type).
Other BARs return e.g. 0xfff0000f or 0xfff00004 and thus manage to break
size calculation due to the "middle" zeroes. Mitigate that copying more
or less what Linux does and do a "find least bit set".
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add Rockchip dwc based PCIe controller driver for rk356x platform.
Driver support Gen3 by operating as a Root complex.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Add a return value to pci_init and use it directly in the post-relocation
init sequence, rather than using a wrapper stub.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
We have two functions which do the same thing. Standardise on
dev_has_ofnode() since there is no such thing as an 'invalid' ofnode in
normal operation: it is either null or missing.
Also move the functions into one place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Now that the sequence-numbering migration is complete, rename this member
back to seq_, adding an underscore to indicate it is internal to driver
model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Most drivers use these access methods but a few do not. Update them.
In some cases the access is not permitted, so mark those with a FIXME tag
for the maintainer to check.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
This reverts commit 828d326216.
This change revers code which asserting PERST# signal when unloading
driver. Driver's remove callback is still there as it is used for other
functionality.
Asserting PERST# signal prior booting kernel is causing that A3720 boards
(Turris MOX and Espressobin) with stable Linux kernel versions 4.14 and
4.19 are not able to detect some PCIe cards (e.g. Compex WLE200 and WLE900)
and anymore. When PERST# signal is not asserted these cards are detected
correctly. As this is regression for existing stable Linux kernel versions
revert this problematic change in U-Boot.
To make cards working with OpenWRT 4.14 kernel it is needed to disable link
training prior booting kernel, which is already done in driver's remove
callback.
Described issue is in Linux kernel pci aardvark driver which is (hopefully)
fixed in latest upstream versions. Latest upstream versions should be able
to initialize PCIe bus and detects cards independently of the link training
and PERST# signal state.
So with this change, U-Boot on A3720 boards should be able to boot OpenWRT
4.14 kernel, stable 4.14 and 4.19 kernels and also latest mainline kernels.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This function current deals with req_seq which is deprecated. Update it to
use the new sequence numbers, putting them above existing aliases. Rename
the function to make this clear.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that we know the sequence number at bind time, there is no need for
special-case code in dm_pci_hose_probe_bus().
Note: the PCI_CAP_ID_EA code may need a look, but there are no test
failures so I have left it as is.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present various drivers etc. access the device's 'seq' member directly.
This makes it harder to change the meaning of that member. Change access
to go through a function instead.
The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fix up the code style for those declarations that should now fit onto one
line, which is all of them that currently do not.
This is needed for dtoc to detect the structs correctly, at present.
Signed-off-by: Simon Glass <sjg@chromium.org>
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: commit 8ec619f8fd ("pci: layerscape: Fixup PCIe EP
mode DT nodes for LX2160A rev2")
This added the PCIe EP nodes fixup of LX2160A, but it
didn't update the condition value when there isn't a
property 'apio-wins'.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Fixed checkpatch error]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
LX2162 is LX2160 based SoC, it has same die as of LX2160
with different packaging.
LX2162A support 64-bit 2.9GT/s DDR4 memory, i2c, micro-click module,
microSD card, eMMC support, serial console, qspi nor flash, qsgmii,
sgmii, 25g, 40g, 50g network interface, one usb 3.0 and serdes
interface to support three PCIe gen3 interface.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
[Fixed whitespace errors]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
resource "config" is required to have minimum 4KB space
to access all config space of PCI Express EP.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
resource "config" is required to have minimum 8KB space
as per hardware documentation.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The register to enable/disable the write-permission of DBI RO
registers should be accessed via the CFG_ADDR/CFG_DATA registers
instead of accessing directly.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In the current implementation, u-boot creates iommu mappings only
for PCI devices enumarated at boot time thus does not take into
account more dynamic scenarios such as SR-IOV or PCI hot-plug.
Add an u-boot env var and a device tree property (to be used for
example in more static scenarios such as hardwired PCI endpoints
that get initialized later in the system setup) that would allow
two things:
- for a SRIOV capable PCI EP identified by its B.D.F specify
the maximum number of VFs that will ever be created for it
- for hot-plug case, specify the B.D.F with which the device
will show up on the PCI bus
More details can be found in the included documentation:
arch/arm/cpu/armv8/fsl-layerscape/doc/README.pci_iommu_extra
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix duplication of this code by placing it in a common function.
Furthermore, the resulting function will be re-used in upcoming
patches.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move the pci device related fdt fixup in a function in order to
re-use it in a following patch. While at it, improve the error
handling.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
