Commit graph

3828 commits

Author SHA1 Message Date
Stefan Roese
a321148b5b ppc4xx: Update lwmon5 board support
This patch includes the following changes for the lwmon5 board support:

- Enable cache in SDRAM
- Use common EHCI driver instead of the PPC4xx specific OHCI driver
  This can be done since only high-speed devices are connected.
- Remove cached TLB entry again after ECC setup
- Use correct define for cache enabling
  (CONFIG_4xx_DCACHE instead of CONFIG_SYS_ENABLE_SDRAM_CACHE)
- Enable FIT image support

Signed-off-by: Stefan Roese <sr@denx.de>
2010-12-17 09:43:45 +01:00
Stefan Roese
cf1971c1c0 ppc4xx: t3corp: Add support for the Xilinx DS617 flash chip
The t3corp board has an Xilinx DS617 flash chip connected to the
onboard FPGA. This patch adds support for these chips. Board
specific flash accessor functions are needed, since the chips
can only be read correctly in 16bit mode.

Additionally the FPGA chip-selects are configured for device-paced
transfers (ready is enabled).

Signed-off-by: Stefan Roese <sr@denx.de>
2010-12-17 09:43:23 +01:00
Reinhard Meyer
f805548b28 AT91: fix TOP9000 build problem and change CONFIG_SYS_TEXT_BASE
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-12-17 08:47:26 +01:00
Prafulla Wadaskar
c291e2fc41 Armada100: Add Board Support for Marvell Aspenite-DB
Aspenite is a Development Board for ASPEN/ARMADA168(88AP168) with
	* Processor upto 1.2GHz
        * Parallel 1Gb x8 DDR2-1066 MHz
        * 16 Mb x16 NOR, 4Gb x8 SLC NAND, footprint for SPI NOR
        * Footprints for eMMC/eSD NAND & MMC x8 card
        * 4-in-1 card reader (xD, MMC/SD/MS Pro), CF True IDE socket
        * SEAF memory board, subset of PISMO2
    With Peripherals:
        * 4.3” WVGA 24-bit LCD
        * Audio codecs (AC97 & I2S), TSI
        * VGA camera
        * Video in via 3 RCA jacks, and HDMI type C out
        * Marvell 88W8688 802.11bg/BT module
        * GPS RF IC
        * Dual analog mics & speakers, headset jack, LED, ambient light sensor
        * USB2.0 HS host  (A), OTG (micro AB)
        * FE PHY, PCIE Mini Card  slot
        * GPIO, GPIO expander with DIP switches for easier selection UART serial over USB, CIR

This patch adds basic board support with DRAM and UART functionality
The patch is tested for boot from DRAM using XDB

Signed-off-by: Mahavir Jain <mjain@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2010-12-16 23:03:05 +01:00
Wolfgang Denk
006915fbb0 Merge branch 'master' of ../master into next 2010-12-16 23:00:53 +01:00
Heiko Schocher
98e6956702 mpc52xx: add support for tqm52xx based board charon
- serial console in PSC1
- 128MiB DRAM
- 32MiB Flash
- FEC Ethernet
- 2 I2C busses
- FPGA on CS3
- IDE
- VGA SMI501

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-12-16 22:58:59 +01:00
Wolfgang Denk
b5d58d8500 Merge branch 'master' of git://git.denx.de/u-boot-arm 2010-12-16 22:49:16 +01:00
Asen Dimov
4f81bf4368 pm9261: ARM relocation support
Signed-off-by: Asen Dimov <dimov@ronetix.at>
2010-12-16 22:46:05 +01:00
Asen Dimov
9a2a05a4a3 pm9263: ARM relocation support
Signed-off-by: Asen Dimov <dimov@ronetix.at>
2010-12-16 22:45:29 +01:00
Asen Dimov
510f794c89 pm9g45: ARM relocation support
Signed-off-by: Asen Dimov <dimov@ronetix.at>
2010-12-16 22:44:02 +01:00
Stefan Roese
37805cf1db ppc4xx: Fix missing linker scripts for partial linking
This patch fixes the acadia_nand and kilauea_nand linker scripts
which have been missing in commit ee8028b7 [ppc4xx: Cleanup for
partial linking and --gc-sections]

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bernhard Weirich <Bernhard.Weirich@riedel.net>
2010-12-15 13:16:33 +01:00
Timur Tabi
fdb9482b42 p1022ds: fix switching of DIU/LBC signals
On the P1022, the pins which drive the video display (DIU) are muxed with the
local bus controller (LBC), so if the DIU is active, the pins need to be
temporarily muxed to LBC whenever accessing NOR flash.

The code which handled this transition is checking and changing the wrong
bits in PMUXCR.

Also add a follow-up read after a write to NOR flash if we're going to
mux back to DIU after the write, as described in the P1022 RM.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-12-13 10:05:51 -06:00
Balaji T K
3e664f6d50 ARMV7: OMAP4: twl6030 add battery charging support
Add battery charging support twl6030 driver.
Add support for battery voltage and current measurements.
Add command to get battery status and start/stop battery charging from USB.

Signed-off-by: Balaji T K <balajitk@ti.com>
Tested-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-12-11 10:56:01 -05:00
Wolfgang Denk
2ced53e1ad Move LDSCRIPT definitions to board config files.
Recent cleanup actions resulted in a number of config.mk files that
contained only LDSCRIPT definitions.  Move these into th respective
board config files and remove the now empty config.mk files.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andre Schwarz <andre.schwarz@matrix-vision.de>
Cc: Peter De Schrijver <p2@mind.be>
Acked-by: Detlev Zundel < dzu@denx.de>
Acked-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Acked-by: Heiko Schocher<hs@denx.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
2010-12-09 10:27:41 +01:00
Wolfgang Denk
263d5c2f84 Remove redundant config.mk files
Recent cleanup actions resulted in a number of config.mk files that
contained only redundant entries like

	PLATFORM_CPPFLAGS += -I$(TOPDIR)

or settings of variables that were not used anywhere in the code, like

	TEXT_END  = 0xfe080000

Remove these unnecessary files.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Scott McNutt <smcnutt@psyent.com>
Cc: Wolfgang Wegner <w.wegner@astro-kom.de>
Cc: Josef Wagner <Wagner@Microsys.de>
Cc: Tolunay Orkun <torkun@nextio.com>
Cc: Frank Panno <fpanno@delphintech.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Brad Kemp <Brad.Kemp@seranoa.com>
Acked-by: Heiko Schocher<hs@denx.de>
2010-12-09 10:25:56 +01:00
Stefano Babic
76bfe76b54 Davinci: add support for the ea20 board
This board uses the OMAP-L138 SOM stacked on a
custom baseboard. It supports SPI Flash, Ethernet
with RMII.

Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-12-09 10:24:12 +01:00
Stefano Babic
a2f2eb76e4 Davinci 8xx: Move common functions to share code
As more Davinci 8xx board can be added, move common code
to be shared between boards.

 * rebased ontop of Sugosh's patches
 * moving the HAWKBOARD_KICK{0,1}_UNLOCK defines to
   arch/arm/include/asm/arch-davinci/davinci_misc.h from to
   arch/arm/include/asm/arch-davinci/da8xx_common.h
 * don't define dram functions in PRELOADER
 * move sync_env_enetaddr into existing EMAC ifdef
 * use misc.c in hawkboard nand_spl

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-12-09 10:24:12 +01:00
Sudhakar Rajashekhara
df48676aea da850: Add RMII support for EMAC
This patch is a port of the work by Sudhakar Rajeshekhara in commit
ab3effbcad8851cc65dc5241a01c064d2030a3b2 of
git://arago-project.org/git/people/sandeep/u-boot-davinci.git.

The da850 UI board has on it an RMII PHY which can be used if the MDC line
to the MII PHY on the baseboard is disabled and the RMII PHY is enabled by
configuring the values of some GPIO pins on the IO expander of the UI board.
This patch implements disabling that line via GPIO2[6], configuring the UI
board's IO expander and setting only the pinmux settings that are needed for
RMII operation.

Tested on da850evm by adding a define for CONFIG_DRIVER_TI_EMAC_USE_RMII.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Sandeep Paulraj <s-paulraj@ti.com>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Mike Frysinger <vapier@gentoo.org>
CC: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-12-09 10:24:12 +01:00
Sughosh Ganu
dfddb5e6ba Add board support for hawkboard
The patch adds basic board support for TI's OMAP-L138 based
Hawkboard. This board is pretty similar to the da850 EVM. Support for
nand and network access is added in this version.

The following bootup procedure is used.

At reset, the Rom Boot Loader(RBL), initialises the ddr and the nand
controllers and copies the second stage bootloader(nand_spl) to
RAM. The secondary bootloader then copies u-boot from a predefined
location in the nand flash to the RAM, and passes control to the
u-boot image.

Three config options are supported
* hawkboard_config - Used to create the u-boot.bin. Tftp the
 u-boot.bin image to the RAM from u-boot, and flash to the nand flash
 at address 0xe0000.

* hawkboard_nand_config - Used to generate the secondary
 bootloader(nand_spl) image. This creates an elf file u-boot-spl
 under nand_spl/. Create an AIS signed image using this file, and
 flash it to the nand flash at address 0x20000. The ais file should
 fit in one block.

* hawkboard_uart_config - This is same as the first image, but with
 the TEXT_BASE as expected by the RBL(0xc1080000). Create the AIS

Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-12-09 10:24:11 +01:00
Sughosh Ganu
3258dcae81 Remove board_init_f function from nand_boot.c
Remove the board_init_f function from nand_spl/nand_boot.c. This
 function is to be defined by all boards using the nand_spl
 functionality in their individual board directory.

 Currently this function was being used by the smdk6400 board. Added
 the board specific function definition.

Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-12-09 10:24:11 +01:00
Sughosh Ganu
a63fbf6730 Move and rename common headers from under
board/davinci.

 Move the davinci common headers to the architecture specific
 include file path.

Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-12-09 10:24:11 +01:00
Dirk Behme
44b0a386bc ARMV7: Vexpress: Fix build error
Fix ca9x4_ct_vxp build error

Configuring for ca9x4_ct_vxp board...
board/armltd/vexpress/libvexpress.o: In function `udelay':
u-boot.git/board/armltd/vexpress/ca9x4_ct_vxp.c:161: multiple
definition of `udelay'
lib/libgeneric.o:u-boot.git/lib/time.c:34: first defined here

lib/libgeneric.o: In function `udelay':

zlib.c:(.text+0x1ee8): undefined reference to `__udelay'

Signed-of-by: Dirk Behme <dirk.behme@googlemail.com>
2010-12-08 23:46:36 +01:00
Matt Waddel
9d37cf310a ARMV7: Vexpress: fix compile warnings
Fixed "pointer from integer without a cast" warnings in Vexpress.

Signed-off-by: Matt Waddel <matt.waddel@linaro.org>
2010-12-08 23:44:51 +01:00
Matt Waddel
7d38f87474 ARMV7: Vexpress: fix build errors
This patch fixes build errors in the vexpress system:
  - Removed sys_proto.h requirement from syslib.c.
  - Switched vexpress to the default armv7 linker script.
  - Renamed TEXT_BASE to CONFIG_SYS_TEXT_BASE.

Signed-off-by: Matt Waddel <matt.waddel@linaro.org>
2010-12-08 23:44:21 +01:00
Wolfgang Denk
b097b9282c Merge branch 'master' of git://git.denx.de/u-boot-arm 2010-12-08 23:17:57 +01:00
Andreas Bießmann
3a4ff8b3cd at91rm9200ek: add configure target for RAM boot
This patch also removes now unnecessary config.mk in board directory and
make usage of new features in boards.cfg.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2010-12-07 22:08:06 +01:00
Reinhard Meyer
d55c5c3f81 AT91: add TOP9000 support
Adds support for the EMK TOP9000 CPU Module which is
based on ATMELs ARM926EJS AT91SAM9XE SoC.

Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-12-07 16:36:41 +01:00
Anatolij Gustschin
14f88c43fc video: move fsl_diu_fb driver to drivers/video
Since the driver is used not only on Freescale boards,
we move it to a common place for video drivers as
suggested by Wolfgang. The patch also cleans up the
top level Makefile.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2010-12-01 20:48:13 +01:00
Wolfgang Denk
49733aa0b9 Merge branch 'master' of /home/wd/git/u-boot/custodians 2010-11-30 22:13:32 +01:00
Kumar Gala
b194577b29 hwconfig: Fix dummy initialization of {board, cpu}_hwconfig
Since board_hwconfig & cpu_hwconfig are defined as weak and dont have a
default value they will get put into the BSS if they aren't defined
elsewhere.  This is problematic as we try to utilize hwconfig before
we've relocated and thus BSS isn't setup.

Instead of giving dummy values in the board files that utilize this
feature, we can just initialize the variables to an empty string and
thus move them out of the BSS if they aren't defined elsewhere.

Also made board_hwconfig & cpu_hwconfig arrays to reduce size associated
with string pointers vs arrays.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-11-30 22:11:19 +01:00
Wolfgang Denk
52eb2c7911 Merge branch 'master' of git://git.denx.de/u-boot-samsung 2010-11-30 21:30:13 +01:00
Dirk Behme
998f4caf6f OMAP3: Zoom2: Fix ARM relocation support
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-30 11:10:48 -05:00
Dirk Behme
25435c6cce OMAP3: Zoom1: Fix ARM relocation support
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-30 11:10:45 -05:00
Dirk Behme
5ec789f6cb OMAP3: SDP3430: Fix ARM relocation support
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-30 11:10:40 -05:00
Minkyu Kang
177feff303 S5P: goni: fix for relocation
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2010-11-30 08:45:25 +09:00
Minkyu Kang
98877c3c0e S5P: smdkc100: fix for relocation
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2010-11-30 08:45:19 +09:00
Vaibhav Hiremath
13acfc6f7f AM3517:Fix for ARM Relocation support
Also change the CONFIG_SYS_TEXT_BASE to 0x80008000, required
with relocation support. This is the load address for primary
boot loader (x-loader).

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-29 16:36:04 -05:00
Mike Frysinger
882b7d726f do_reset: unify duplicate prototypes
The duplication of the do_reset prototype has gotten out of hand,
and they're not all in sync.  Unify them all in command.h.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-11-28 21:47:24 +01:00
Mike Frysinger
36ebb78779 do_bootm: unify duplicate prototypes
The duplication of the do_bootm prototype has gotten out of hand,
and they're pretty much all outdated (wrt constness).  Unify them
all in command.h.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-11-28 21:45:32 +01:00
Thomas Weber
fd2aa8e2e7 gdsys: osd: Use return value of cmd_usage
Use the return value of cmd_usage instead of ignoring this
and returning a 1.

Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2010-11-27 23:35:14 +01:00
Kristoffer Ericson
f4f88921a5 Fix jornada memory init
* Fix memory initialization. This fixes the problem
  with kernel oopses during heavy load.

* Cleanup pinsetup, which for reference is among
  other things needed for proper flash erasing.

Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
2010-11-27 23:35:12 +01:00
Wolfgang Denk
e2c2a95e60 74xx_7xx: Cleanup for partial linking and --gc-sections
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
2010-11-27 23:35:12 +01:00
Wolfgang Denk
ba273f066f 8260: Cleanup for partial linking and --gc-sections
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
2010-11-27 23:35:12 +01:00
Wolfgang Denk
de550d6b34 824x: Cleanup for partial linking and --gc-sections
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
2010-11-27 23:35:12 +01:00
Wolfgang Denk
085ecde156 5xxx: Cleanup for partial linking and --gc-sections
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
2010-11-27 23:35:11 +01:00
Wolfgang Denk
566d49a3f5 512x: Cleanup for partial linking and --gc-sections
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Timur Tabi <timur@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
2010-11-27 23:35:11 +01:00
Wolfgang Denk
cd0402a730 8xx: Cleanup for partial linking and --gc-sections
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
2010-11-27 23:35:10 +01:00
Wolfgang Denk
ee8028b7f1 ppc4xx: Cleanup for partial linking and --gc-sections
This commit adapts 4xx boards for partial linking with --gc-sections.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Tirumala Marri <tmarri@apm.com>
Cc: David Updegraff <dave@cray.com>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Larry Johnson <lrj@acm.org>
Cc: Peter De Schrijver <p2@mind.be>
Cc: Niklaus Giger <niklaus.giger@netstal.com>
Cc: Daniel Poirot <dan.poirot@windriver.com>
Acked-by: Stefan Roese <sr@denx.de>
2010-11-27 23:35:09 +01:00
Stefan Roese
c56f84ca9c ppc4xx: Fix build problems of IBM DDR2 NAND booting targets
This change is needed to compile the PPC4xx NAND booting targets
equipped with the IBM DDR2 SDRAM controller.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
2010-11-26 22:08:19 +01:00
Wolfgang Denk
aa72d8baaa PPChameleonEVB and CATcenter need a custom linker script
These boards use an embedded environment, which is not supported by the
generic arch/powerpc/cpu/ppc4xx/u-boot.lds script.

The breakage was introduced by commit 2cd95a2 "ppc4xx: Remove board
specific linker scripts from most PPC4xx boards"

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Andrea Marson <andrea.marson@dave-tech.it>
Acked-by: Stefan Roese <sr@denx.de>
2010-11-26 22:08:19 +01:00
Wolfgang Denk
84db715ea4 cam5200_niosflash: fix build warnings
Fix warnings:

cam5200_flash.c: In function 'write_word_32':
cam5200_flash.c:443: warning: dereferencing type-punned pointer will break strict-aliasing rules
cam5200_flash.c: In function 'write_word_16':
cam5200_flash.c:684: warning: dereferencing type-punned pointer will break strict-aliasing rules

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
2010-11-26 22:08:18 +01:00
Wolfgang Denk
739192b425 IDS8247: remove redundant flash.c file
The IDS8247 board is configured to use the CFI flash driver, so drop
the now redundant custom flash.c file.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
2010-11-26 22:08:18 +01:00
Wolfgang Denk
afaa27bdd6 barco: drop unsupported board configuration
The barco board appears to be unmaintained since it was added about 5
years ago. The environment location has probably never been correct.
Drop it.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Marc Leeman <marc.leeman@barco.com>
Acked-by: Stefan Roese <sr@denx.de>
2010-11-26 22:08:18 +01:00
Wolfgang Denk
93b1140090 ERIC: drop unsupported board configuration
The ERIC board appears to be unmaintained for more than 9 years. The
environment location has probably never been correct, and has been
definitely broken since for at least a year.  Drop it.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Swen Anderson <sand@peppercon.de>
Acked-by: Stefan Roese <sr@denx.de>
2010-11-26 22:08:17 +01:00
Eric Cooper
38041db740 Seagate FreeAgent DockStar support
start with sheevaplug configuration
add modifications by Alexander Holler <holler@ahsoftware.de>
    change RAM definitions to one bank (128 MB)
    change ident string and prompt
define MTD partitions and default environment variables
add support for LEDs

Signed-off-by: Eric Cooper <ecc@cmu.edu>
2010-11-26 21:12:52 +01:00
Sekhar Nori
4f6fc15b42 DA850 EVM: passing maximum clock rate information to kernel
The TI DA850/OMAP-L138/AM18x EVM can be populated with devices
having different maximum allowed CPU clock rating.

The maximum clock the chip can support can only be determined from
the label on the package (not software readable).

Introduce a method to pass the maximum allowed clock rate information
to kernel using ATAG_REVISION. The kernel uses this information to
determine the maximum cpu clock rate reachable using cpufreq.

Note that U-Boot itself does not set the CPU clock rate. The CPU
clock is setup by a primary bootloader ("UBL"). The rate setup by
UBL could be different from the maximum clock rate supported by the
device.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-19 16:29:11 -05:00
Grazvydas Ignotas
23df4f691a OMAP3: pandora: fix relocation and init memory
map

Fix the build breakage introduced by the recent relocation
and memory layout changes for ARM.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-19 16:28:23 -05:00
Sebastien Carlier
6d8962e814 Switch from archive libraries to partial linking
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils.  As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".

This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.

The name of each former library archive is preserved except for
extensions which change from ".a" to ".o".  This commit updates
references accordingly where needed, in particular in some linker
scripts.

This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols.  Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.

Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
2010-11-17 21:02:18 +01:00
Wolfgang Denk
d7b1970015 Merge branch 'master' of git://git.denx.de/u-boot-arm 2010-11-17 20:54:39 +01:00
Peter Tyser
e7060dc570 mpc85xx: Fix SERDES/eTSEC message indentation
Previously some mpc85xx boards printed indented messages such as the
following on bootup:
  printf("    eTSEC4 is in sgmii mode.\n");
  printf("    Serdes2 disalbed\n");

The bootup appearance looks cleaner if the indentation is removed which
aligns these messages with other bootup output.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
CC: galak@kernel.crashing.org
2010-11-14 23:46:44 +01:00
Peter Tyser
8ca78f2c89 fsl: Clean up printing of PCI boot info
Previously boards used a variety of indentations, newline styles, and
colon styles for the PCI information that is printed on bootup.  This
patch unifies the style to look like:

...
NAND:  1024 MiB
PCIE1: connected as Root Complex
           Scanning PCI bus 01
        04  01  8086  1010  0200  00
        04  01  8086  1010  0200  00
        03  00  10b5  8112  0604  00
        02  01  10b5  8518  0604  00
        02  02  10b5  8518  0604  00
        08  00  1957  0040  0b20  00
        07  00  10b5  8518  0604  00
        09  00  10b5  8112  0604  00
        07  01  10b5  8518  0604  00
        07  02  10b5  8518  0604  00
        06  00  10b5  8518  0604  00
        02  03  10b5  8518  0604  00
        01  00  10b5  8518  0604  00
PCIE1: Bus 00 - 0b
PCIE2: connected as Root Complex
           Scanning PCI bus 0d
        0d  00  1957  0040  0b20  00
PCIE2: Bus 0c - 0d
In:    serial
...

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
CC: wd@denx.de
CC: sr@denx.de
CC: galak@kernel.crashing.org
2010-11-14 23:46:42 +01:00
Wolfgang Denk
227b725155 Merge branch 'master' of git://git.denx.de/u-boot-ti 2010-11-13 00:19:55 +01:00
Wolfgang Denk
d963e84c92 Merge branch 'master' of /home/wd/git/u-boot/master 2010-11-12 22:24:06 +01:00
Becky Bruce
b1b7646493 TQM85xx: Fix bug introduced by 83xx/85xx/86xx: LBC register cleanup
The size of the other bank needed to be added to the br0 setting;
this got dropped in the LBC cleanup.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Tested-by: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-11-12 09:45:16 -06:00
Timur Tabi
46299078e6 powerpc/corenet_ds: display the RCW at boot
Display the 64-byte Reset Configuration Word (RCW) during boot, so that
there's no confusion as to what RCW U-boot is using.

Reset Configuration Word (RCW):
       00000000: 4a500000 00000000 18181818 00008888
       00000010: 28402400 00002000 fe800000 01200000
       00000020: 00000000 00000000 00000000 000b0000
       00000030: 00000000 00000000 00000000 00000000

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-11-12 09:45:16 -06:00
Priyanka Jain
39c2a6eb75 p1_p2_rdb: to set SQW/INT pin of RTC as INT line
SQW/INT pin in RTC can be used for generating square wave(by default) or
as interrupt line.  U-boot is registering this pin for interrupts.
Configuring SQW/INT bit as interrupt line during board initialization
to avoid spurious interrupts generated by square wave.

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-11-12 09:45:11 -06:00
Sanjeev Premi
76ee9a2c3b omap3evm: Fix mechanism to identify board revision
Function omap3_evm_get_revision() - to identify the
board revision was called at end of setup_net_chip().

Board revision can be ascertained only by identifying
the Ethernet chipset - but combining setup operations
with revision detection isn't a good idea. So, moved
the function after call to setup_net_chip().

Function setup_net_chip() should be ideally be called
only when CONFIG_CMD_NET is defined. But this leaves
the board revision "undetected". This patch allows
static definition of revision or default fallback to
the latest revision.

Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-04 16:02:32 -04:00
Sanjeev Premi
63f42400e5 omap3evm: Wrap function under CONFIG_USB_OMAP3
The function omap3_evm_need_extvbus() is required
only when USB support is configured.

Wrapped this function in #ifdef CONFIG_USB_OMAP3.

Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-04 16:02:29 -04:00
Sanjeev Premi
6a1e58eb6a omap3evm: Support relocation
This patch adds relocation support for omap3evm.
Content of the patch is based on changes for
Beagleboard.

Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-04 16:01:46 -04:00
Enric Balletbo i Serra
ac657c42af ARMV7: OMAP3: Use generic mmc driver on OMAP3 IGEP module
This patch switches from the legacy mmc driver to the new generic mmc driver

Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-04 15:34:37 -04:00
Enric Balletbo i Serra
f49d7b6cab ARMV7: OMAP3: Use generic mmc driver on IGEP v2
This patch switches from the legacy mmc driver to the new generic mmc driver

Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-04 15:34:33 -04:00
Koen Kooi
ca5f80ae97 ARMV7: OMAP3: Add expansion board detection for Beagle
Beagle expansion boards contain an i2c eeprom to identify themselves.
This patch adds code to read and parse the eeprom contents.  It prints
the expansion board name and revision and modifies environment variables
as appropriate. This patch is based on the Overo expansion board code.

Signed-off-by: Koen Kooi <k-kooi@ti.com>
Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-04 15:27:11 -04:00
Steve Sakoman
d64b5b8915 ARMV7: OMAP3: Add expansion board detection for Overo
Overo expansion boards contain an i2c eeprom to identify themselves.
This patch adds code to read and parse the eeprom contents.  It prints
the expansion board name and revision and modifies environment variables
as appropriate.

Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-04 15:27:06 -04:00
Steve Sakoman
a711edfae1 ARMV7: OMAP3: IGEP: Rename TEXT_BASE
Commit 14d0a02a "Rename TEXT_BASE into CONFIG_SYS_TEXT_BASE" missed the
IGEP boards since they were just added.

Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-04 15:26:57 -04:00
Wolfgang Denk
0c0892be0d Merge branch 'master' of git://git.denx.de/u-boot-marvell
Conflicts:
	include/configs/km_arm.h

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-29 22:03:00 +02:00
Wolfgang Denk
d75c2a3d7f Merge branch 'master' of git://git.denx.de/u-boot-imx 2010-10-29 21:50:24 +02:00
Wolfgang Denk
17dd883c5b Merge branch 'master' of git://git.denx.de/u-boot-samsung 2010-10-29 21:47:48 +02:00
Wolfgang Denk
a9aa392629 Drop support for CONFIG_SYS_ARM_WITHOUT_RELOC
When this define was introduced, the idea was to provide a soft
migration path for ARM boards to get adapted to the new relocation
support.  However, other recent changes led to a different
implementation (ELF relocation), where this no longer works.  By now
CONFIG_SYS_ARM_WITHOUT_RELOC does not only not help any more, but it
actually hurts because it obfuscates the actual code by sprinkling it
with lots of dead and non-working debris.

So let's make a clean cut and drop CONFIG_SYS_ARM_WITHOUT_RELOC.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-10-29 21:39:59 +02:00
Prafulla Wadaskar
31d80c77ff kirkwood: get rid of config.mk files
After moving the definition of CONFIG_SYS_TEXT_BASE to the respective
board config files, all Marvell kirkwood board have just a single and
common entry in their config.mk files:

	KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg

Replace the only reference to KWD_CONFIG in the top level Makefile by
an equivalent setting, and remove all kirkwood config.mk files.

Signed-off-by: Wolfgang Denk <wd at denx.de>
Cc: Prafulla Wadaskar <prafulla at marvell.com>
Cc: Siddarth Gore <gores at marvell.com>
Cc: Simon Kagstrom <simon.kagstrom at netinsight.net>
Cc: Heiko Schocher <hs at denx.de>
Cc: Eric Cooper <ecc at cmu.edu>
Acked-by: Wolfgang Denk <wd at denx.de>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2010-10-28 19:12:06 +05:30
Shawn Guo
1ab027cbf6 mx51evk: support new relocation scheme
This patch is to fix build breakage and support new relocation
scheme for mx51evk.

- Correct IRAM base address and add size definition

  The IRAM starts from 0x1FFE0000 on final revsion i.mx51 than
  0x1FFE8000 which is for older revision.

- Include imx-regs.h in mx51evk.h

  Definitions like CSD0_BASE_ADDR and IRAM_BASE_ADDR can be
  referred to.

- Define CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE

  They are used to define init RAM layout.

- Remove comment for CONFIG_SYS_GBL_DATA_SIZE which has been
  buried by Wolfgang's commit below

  25ddd1fb: Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value

Signed-off-by: Shawn Guo <shawn.gsc@gmail.com>
2010-10-28 11:43:23 +02:00
Shawn Guo
888b4f435f mx51evk: Fix 2 hours reset issue
The mx51evk u-boot has an issue that system will get reset
every 2 hours.

MC13892 has an inside charge timer which expires in 120 minutes.
If ICHRG and CHGAUTOB are not set properly, this timer expiration
will get system power recycled.

Since mx51evk has no Li-Ion battery on board, the patch sets
ICHRG in externally powered mode and sets CHGAUTOB bit to avoid
automatic charging, so that system will not get reset by this
timer expiration.

The patch also corrects the bit field definition of register 48
(Charger 0) per latest MC13892 Reference Manual.

Signed-off-by: Shawn Guo <shawn.gsc@gmail.com>
2010-10-28 11:42:34 +02:00
Jason Liu
95707aaa9e MX5:use common u-boot.lds of cpu layer
Remove u-boot.lds from mx5 and use the common u-boot.lds
of cpu layer. This patch also fix the building errors:

arch/arm/cpu/armv7/start.o: In function `_rel_dyn_start_ofs':
arch/arm/cpu/armv7/start.S:283: undefined reference to `__rel_dyn_start'
arch/arm/cpu/armv7/start.o: In function `_rel_dyn_end_ofs':
arch/arm/cpu/armv7/start.S:283: undefined reference to `__rel_dyn_end'
arch/arm/cpu/armv7/start.o: In function `_dynsym_start_ofs':
arch/arm/cpu/armv7/start.S:283: undefined reference to `__dynsym_start'

Signed-off-by: Jason Liu <r64343@freescale.com>
2010-10-28 10:32:20 +02:00
Stefano Babic
51fd9a7e01 MX51: add CONFIG_SYS_TEXT_BASE to vision2 board, use general ld script
Recent patch changed TEXT_BASE to CONFIG_SYS_TEXT_BASE and
vision2 board was not updated.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-10-28 10:32:20 +02:00
C Nauman
d9abba8254 Add generic support for samsung s3c2440
This patch adds generic support for the Samsung s3c2440 processor.

Global s3c24x0 changes to struct members converting from upper case to
lower case.

Signed-off-by: Craig Nauman <cnauman@diagraph.com>
Cc: kevin.morfitt@fearnside-systems.co.uk
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2010-10-28 15:35:56 +09:00
Wolfgang Denk
071bc92330 Coding Style cleanup
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-27 22:48:30 +02:00
Wolfgang Denk
f503d52a9e mcu25: fix out of tree building
Out of tree building of the Netstal mcu25 board failed like
that:

Configuring for mcu25 board...
Assembler messages: Fatal error: can't create /work/wd/tmp-ppc/board/netstal/mcu25/../common/fixed_sdram.o: No such file or directory
Assembler messages: Fatal error: can't create /work/wd/tmp-ppc/board/netstal/mcu25/../common/nm_bsp.o: No such file or directory

Adapt (and simplify) the Makefile.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Niklaus Giger <niklaus.giger@netstal.com>
2010-10-27 20:13:46 +02:00
Sughosh Ganu
f760d14acc Remove config.mk for da8xxevm based boards.
Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the
now unnecessary config.mk file.

Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
2010-10-26 21:17:24 +02:00
Wolfgang Denk
25ddd1fb0a Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough.  This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool.  In the result, all definitions of this value can be
deleted from the board config files.  We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.

No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-26 21:05:30 +02:00
Wolfgang Denk
553f09823c Rename CONFIG_SYS_INIT_RAM_END into CONFIG_SYS_INIT_RAM_SIZE
CONFIG_SYS_INIT_RAM_END was a misnomer as it suggests this might be
some end address; to make the meaning more clear we rename it into
CONFIG_SYS_INIT_RAM_SIZE

No other code changes are performed in this patch, only minor editing
of white space (due to the changed length) and the comments was done,
where noticed.

Note that the code for the PATI and cmi_mpc5xx board configurations
looks seriously broken.  Last known maintainers on Cc:

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Denis Peter <d.peter@mpl.ch>
Cc: Martin Winistoerfer <martinwinistoerfer@gmx.ch>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-26 21:03:25 +02:00
Wolfgang Denk
7ad1a5f69d Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx 2010-10-26 20:57:41 +02:00
Dirk Eibach
a605ea7e83 ppc4xx: Add Io and IoCon 405EP board support
Board support for the Guntermann & Drunck CATCenter Io.
Board support for the Guntermann & Drunck IoCon.

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2010-10-25 17:07:46 +02:00
Wolfgang Denk
1339657abd hcu4, hcu5: fix out of tree building
Out of tree building of the Netstal hcu4 and hcu5 boards failed like
that:

Assembler messages:
Fatal error: can't create /work/wd/tmp-ppc/board/netstal/hcu4/../common/fixed_sdram.o: No such file or directory
Assembler messages:
Fatal error: can't create /work/wd/tmp-ppc/board/netstal/hcu4/../common/nm_bsp.o: No such file or directory
make[1]: *** [/work/wd/tmp-ppc/board/netstal/hcu4/../common/fixed_sdram.o] Error 2

Adapt (and simplify) the respective Makefiles.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Niklaus Giger <niklaus.giger@netstal.com>
2010-10-24 16:49:12 +02:00
Wolfgang Denk
bc5e1701f3 lite5200b_PM: fix compile warning
Fix warning:

icecube.c: In function 'lite5200b_wakeup':
icecube.c:83: warning: format '%08lx' expects type 'long unsigned int', but argument 2 has type 'void (*)(void)'

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-24 15:37:12 +02:00
Wolfgang Denk
02cf8fd6fb Merge branch 'for-wd-master' of git://git.denx.de/u-boot-pxa 2010-10-23 22:08:33 +02:00
Wolfgang Denk
f2b382ea06 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2010-10-23 21:59:42 +02:00
Wolfgang Denk
33a08c10c7 Merge branch 'master' of git://git.denx.de/u-boot-video 2010-10-23 21:56:51 +02:00
Wolfgang Denk
678150f155 Merge branch 'master' of git://git.denx.de/u-boot-sh 2010-10-23 21:45:57 +02:00
John Schmoller
bfe18815e8 XPedite5500 board support
Initial support for Extreme Engineering Solutions XPedite5500 -
a P2020-based PMC/XMC single board computer.

Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-22 03:04:41 -05:00
Peter Tyser
c00ac259f6 xes: Make X-ES board names more generic
Some U-Boot images for X-ES boards support multiple products in the same
family.  For example, the XPedite5370, XPedite5371, and XPedite5372 are
similar enough that one U-Boot image can work on all 3 cards.  To make it
clear that a U-Boot image can work on boards of the same family, rename
the boards with the least significant digit of 'x'.

While we're at it, change the board config file and make targets to be
lowercase.

Also change the default uImage and fdt filenames to "board.uImage" and
"board.dtb" to be more generic.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-22 02:17:23 -05:00
John Schmoller
72fb68d53c xes: Add board_flash_wp_on()
Add board_flash_wp_on() to check a pca9557 gpio pin to see
if non-volatile memory write protection is enabled.

Previously, write protected NOR flashes would fail initialization which
resulted in a bootup error such as:

 ...
 DTT:   53 C local / 64 C remote (adt7461@4c)
 DTT:   54 C local (ds1621@48)
 FLASH: Executed from FLASH1
 POST memory PASSED
 FLASH: ## Unknown FLASH on Bank 1 - Size = 0x00000000 = 0 MB
 ## Unknown FLASH on Bank 2 - Size = 0x00000000 = 0 MB
 *** failed ***
 ### ERROR ### Please RESET the board ###

With this patch, NOR flash initialization is skipped:

 ...
 DTT:   53 C local / 64 C remote (adt7461@4c)
 DTT:   54 C local (ds1621@48)
 FLASH: Executed from FLASH1
 POST memory PASSED
 FLASH: Uninitialized - Write Protect On
 L2:    1024 KB enabled
 NAND:  1024 MiB
 ...

Note that flash related commands such as flinfo and saveenv will error
out when flash write protection is enabled.

Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-22 02:17:19 -05:00