This commit converts mccmon6's u-boot proper (in a single commit to avoid
build breaks) to use solely DM/DTS.
The DTS description of the mccmon6 has been ported from Linux kernel
(v4.20, SHA1: 8fe28cb58bcb235034b64cbbb7550a8a43fd88be)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
In order for 'bmode emmc' to work, the eMMC needs to be initialized in the
SPL. This change initializes the eMMC as BOOT_DEVICE_MMC1 (index=0).
Signed-off-by: Claudius Heine <ch@denx.de>
The board_boot_modes contained the wrong values for the emmc entry.
The eMMC here is connected over a 8-bit bus.
This change allows to use the 'bmode emmc' command to boot from emmc.
Signed-off-by: Claudius Heine <ch@denx.de>
The expire_now function was previously setting the watchdog timeout to
minimum and waiting for the watchdog to expire. However, this watchdog
also has bits to trigger immediate reset. Use those instead, like the
Linux imx2_wdt driver does.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
The Linux imx2_wdt driver uses a fsl,ext-reset-output boolean in the
device tree to specify whether the board design should use the external
reset instead of the internal reset. Use this boolean to determine which
mode to use rather than using external reset unconditionally.
For the legacy non-DM mode, the external reset is always used in order
to maintain the previous behavior.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Add u-boot,dm-pre-reloc properties for uart pinmux configuration
nodes, which enables UART as early as possible (before relocation).
Without this we miss almost the half of output (U-boot version,
CPU defails, Reset cause, DRAM details etc.).
Fixes: cd69e8ef9b ("colibri-imx6ull: migrate pinctrl and regulators to dtb/dm")
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Introduce imx6ull-colibri-u-boot.dtsi for u-boot specific properties to
keep original imx6ull-colibri.dts in sync with Linux.
Move all contents of imx6ull-colibri.dts to imx6ull-colibri.dtsi +
additionally fix checkpatch warnings.
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
According to IMX28CEC rev. 4, 10/2018, Table 15. Recommended Operating
Conditions, page 16, the VDDD should be set to 1.55V when the CPU is
operating at 454MHz. This is the case in U-Boot, hence increase the
VDDD voltage. This fixes instability when performing TFTP transfers.
Increase the brownout threshold to 1.4V. The documentation recommends
1.45V setting for the brownout, however, this triggers failure during
power block init, so keep the brownout slightly lower.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
imx6_is_bmode_from_gpr9 always returns false, because
IMX6_SRC_GPR10_BMODE is 1<<28 and gets casted to u8 on return.
This moves the function body into imx6_src_get_boot_mode, since that is the
only one using it and it is on the same abstraction level (accessing
registers directly).
Signed-off-by: Claudius Heine <ch@denx.de>
After the following commit:
commit 772b55723b ("imx: Introduce CONFIG_SPL_FORCE_MMC_BOOT to force MMC
boot on falcon mode")
it is possible to set the CONFIG_SPL_FORCE_MMC_BOOT flag, which allows
using MMC device as boot device regardless of the device used by Boot ROM
(FBL) as the first boot medium.
Display5 board needs this flag set to allow falcon boot from eMMC device.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Introduce disable_ipu_clock(). This is done in preparation for
configuring the NoC registers on i.MX6QP in SPL.
Afer the NoC registers are set the IPU clocks can be disabled.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The code can be made simpler by using setbits_le32(), so switch
to it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Similar to 90d3d78a1c ("gitlab-ci: Prepend to PATH rather than replace
it") we need to prepend the PATH with our additional binaries and not
replace the value fully as doing so breaks virtualenv.
Signed-off-by: Tom Rini <trini@konsulko.com>
Provide a better user interface for setting UEFI variables.
Bug fixes:
- ext4 file system not discovered on UEFI block device
- 'make tests' build error on 32bit systems
-----BEGIN PGP SIGNATURE-----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=f0m8
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-01-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-01-rc2
Provide a better user interface for setting UEFI variables.
Bug fixes:
- ext4 file system not discovered on UEFI block device
- 'make tests' build error on 32bit systems
Bootstage improvements for TPL, SPL
Various sandbox and dm improvements and fixes
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl24zDoRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZRiwf+Mf7oG//zjiZcHaPP6KOFb1CjwqLSuiaI
eCYB6GEZXuSpc8MjAw+baAfIw8MMFuaCfPsUQ5dDo391neK0sW9kkEsdcXnQBpB3
GdJYcewLN1UuJZovriGobIisGc0GQHh8gmRcVGWSKoEt+gAQauRtVYBIUPuS3JG+
ihZgYmVgICa+3tqavIbP2oZdXLuLAxR65mfiQHtiJwdCN3OOzyls2v0T0slQX9GV
ln6EvTk8OMIudBmkB7YiTmJF7AB+3PH/uBaiYyTKO9gtjLhnmCFvG5HxJTRFOKvU
F4oVWZJDEcqfZvYgWg8i5vgokMP41nzLfBr7j5ifUX1f3xwCHy/Tpw==
=S4XI
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-29oct19' of git://git.denx.de/u-boot-dm
- Fix for patman with email addresses containing commas
- Bootstage improvements for TPL, SPL
- Various sandbox and dm improvements and fixes
Similar to the rework for GitLab-CI and Travis-CI, rework the Azure
Pipeline to use python3 and requirements.txt to install the necessary
modules.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add optional parameter to 'avb verify' sub-command, so that user is able
to specify which slot to use, in case when user's partitions are
slotted. If that parameter is omitted, the behavior of 'avb verify' will
be the same as before, so user API is content.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Acked-by: Igor Opaniuk <igor.opaniuk@gmail.com>
After updating libavb to most recent version from AOSP/master, two new
warnings appear:
Warning #1:
lib/libavb/avb_cmdline.c: In function 'avb_append_options':
lib/libavb/avb_cmdline.c:365:15: warning: 'dm_verity_mode' may be
used uninitialized in this function
[-Wmaybe-uninitialized]
new_ret = avb_replace(
^~~~~~~~~~~~
slot_data->cmdline, "$(ANDROID_VERITY_MODE)", dm_verity_mode);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
lib/libavb/avb_cmdline.c:374:8: warning: 'verity_mode' may be used
uninitialized in this function
[-Wmaybe-uninitialized]
if (!cmdline_append_option(
^~~~~~~~~~~~~~~~~~~~~~
slot_data, "androidboot.veritymode", verity_mode)) {
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Warning #2:
lib/libavb/avb_slot_verify.c: In function 'avb_slot_verify':
lib/libavb/avb_slot_verify.c:1349:23: warning: 'ret' may be used
uninitialized in this function
[-Wmaybe-uninitialized]
AvbSlotVerifyResult ret;
^~~
Fix those by providing default return values to affected functions.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Update libavb to commit 5fbb42a189aa in AOSP/master, because new version
has support for super partition [1], which we need for implementing
Android dynamic partitions. All changes from previous patches for libavb
in U-Boot are accounted for in this commit:
- commit ecc6f6bea6 ("libavb: Handle wrong hashtree_error_mode in
avb_append_options()")
- commit 897a1d947e ("libavb: Update SPDX tag style")
- commit d8f9d2af96 ("avb2.0: add Android Verified Boot 2.0 library")
Tested on X15:
## Android Verified Boot 2.0 version 1.1.0
read_is_device_unlocked not supported yet
read_rollback_index not supported yet
read_is_device_unlocked not supported yet
Verification passed successfully
AVB verification OK.
Unit test passes:
$ ./test/py/test.py --bd sandbox --build -k test_avb
test/py/tests/test_android/test_avb.py ss..s.
[1] 49936b4c01
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
Acked-by: Igor Opaniuk <igor.opaniuk@gmail.com>
When running the following command
mkimage -f auto -A arm -O linux -T kernel -C none -a 0x8000 -e 0x8000 \
-d zImage -b zynq-microzed.dtb -i initramfs.cpio image.ub
the type of fdt subimage is the same as of the main kernel image and
the architecture of the initramfs image is not set. Such an image is
refused by U-Boot when booting. This commits sets the mentioned
attributes, allowing to use the "-f auto" mode in this case instead of
writing full .its file.
Following is the diff of mkimage output without and with this commit:
FIT description: Kernel Image image with one or more FDT blobs
Created: Thu Sep 12 23:23:16 2019
Image 0 (kernel-1)
Description:
Created: Thu Sep 12 23:23:16 2019
Type: Kernel Image
Compression: uncompressed
Data Size: 4192744 Bytes = 4094.48 KiB = 4.00 MiB
Architecture: ARM
OS: Linux
Load Address: 0x00008000
Entry Point: 0x00008000
Image 1 (fdt-1)
Description: zynq-microzed
Created: Thu Sep 12 23:23:16 2019
- Type: Kernel Image
+ Type: Flat Device Tree
Compression: uncompressed
Data Size: 9398 Bytes = 9.18 KiB = 0.01 MiB
Architecture: ARM
- OS: Unknown OS
- Load Address: unavailable
- Entry Point: unavailable
Image 2 (ramdisk-1)
Description: unavailable
Created: Thu Sep 12 23:23:16 2019
Type: RAMDisk Image
Compression: Unknown Compression
Data Size: 760672 Bytes = 742.84 KiB = 0.73 MiB
- Architecture: Unknown Architecture
+ Architecture: ARM
OS: Linux
Load Address: unavailable
Entry Point: unavailable
Default Configuration: 'conf-1'
Configuration 0 (conf-1)
Description: zynq-microzed
Kernel: kernel-1
Init Ramdisk: ramdisk-1
FDT: fdt-1
Loadables: kernel-1
Signed-off-by: Michal Sojka <michal.sojka@cvut.cz>
For some controllers PHYs can be optional. Handling NULL pointers without
crashing nor failing, makes it easy to handle optional PHYs.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
malloc_cache_aligned() might return zero, so fix potential NULL pointer
access if __GFP_ZERO flag is set.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Add a simple implementation of this function, to allow logging to be
enabled in the SPL or TPL for systems that rely on the tiny printf()
implementation.
To keep the code size small,
- The function is built only when logging is enabled, as it
(currently) is not needed otherwise; and
- Like the existing implementation of snprintf(), its buffer-size
parameter is ignored.
Signed-off-by: Simon South <simon@simonsouth.net>
In cmd/regulator.c an error occurs with GCC 9.2.1 if CONFIG_ERRNO_STR is
not defined:
cmd/regulator.c: In function ‘failure’:
cmd/regulator.c:20:2: error: ‘%s’ directive argument is null
[-Werror=format-overflow=]
20 | printf("Error: %d (%s)\n", ret, errno_str(ret));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In function ‘constraint’,
inlined from ‘constraint’ at cmd/regulator.c:111:12:
cmd/regulator.c:115:3: error: ‘%s’ directive argument is null
[-Werror=format-overflow=]
115 | printf(" %s (err: %d)\n", errno_str(val), val);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
errno_str() should return a valid string instead of NULL if
CONFIG_ERRNO_STR is not defined.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Macro ERRNO_MSG() ignores the error number but we should still use the same
constants as in include/linux/errno.h.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This choice is not about SPL for which we have a separate choice.
Fixes: 95f4bbd581 ("lib: fdt: Allow LZO and GZIP DT compression in U-Boot")
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
The signature 0x55 0xAA in bytes 510 and 511 of the first sector can either
indicate a DOS partition table of the first sector of a FAT file system.
The current code tries to check if the partition table is valid by looking
at the boot indicator of the partition entries. But first of all it does
not count from 0 to 3 but only from 0 to 2. And second it misses to
increment the pointer for the partition entry.
If it is a FAT file system can be discovered by looking for the text 'FAT'
at offset 0x36 or 'FAT32' at offset 0x52. In a DOS PBR there are no
partition entries, so those bytes are undefined. Don't require the byte at
offset 0x1BE to differ from 0x00 and 0x80.
With the patch the logic is changed as follows:
If the partition table has either an invalid boot flag for any partition or
has no partition at all, check if the first sector is a DOS PBR by looking
at the FAT* signature.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Provide a unit test for errno_str(). Test that known and unknown error
numbers are handled correctly.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
If errno_str() is called with an unsupported error number, do not return a
random pointer but a reasonable text.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add get_timer_us(), which is useful e.g. when we need higher
precision timestamps.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
[trini: Fixup arch/arm/mach-bcm283x/include/mach/timer.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
Make sure that the PCI busses are enumerated before trying to
find a NVMe device.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Change the stack-allocated buffer for the identification command
to explicitly allocate page-aligned buffers. Even though the spec
seems to allow having admin queue commands on non page-aligned
buffers, it seems to not be possible on my i.MX8MQ board with a
a Silicon Power P34A80. Since all of the NVMe drivers I have seen
always do admin commands on a page-aligned buffer, which does work
on my system, it makes sense for us to do that as well.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It's possible that the data cache for the buffer still holds data
to be flushed to memory, since the buffer was probably used as stack
before. Thus we need to make sure to flush it also on reads, since
it's possible that the cache is automatically flused to memory after
the NVMe DMA transfer happened, thus overwriting the NVMe transfer's
data. Also add a missing dcache flush for the prp list.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Update from upstream.
Just minor changes like checking that the author has also done a sign-off.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Some configurations (i.e. sandbox) result in unused
splash_display_banner() and we get build errors like:
common/splash.c:148:20: error: unused function 'splash_display_banner' [-Werror,-Wunused-function]
static inline void splash_display_banner(void) { }
Drop empty inline function and add guards around the call.
Fixes: d2a8271c88 ("splash: fix splash banner output")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
As initially this feature was implemented as a negative CONFIG and
later it was redesigned to be positive the help text should be
updated to reflect this change.
This commit updates the help text to match the current implementation.
Signed-off-by: Walter Lozano <wlozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When we have an excess size growth, fix the "limit" printf call to pass
in just the limit variable rather than the string bytes to the format
character.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
_gpio_direction_output function currently calls gpio_set_value
with the wrong gpio number. gpio_set_value in the uclass driver
expects a different gpio number and the _gpio_direction_output
is currently providing the number specific to the bank.
Hence fix it by calling the _gpio_set_value function instead.
Reported-by: Faiz Abbas <faiz_abbas@ti.com>
Fixes: 8e51c0f254 ("dm: gpio: Add DM compatibility to GPIO driver for Davinci")
Signed-off-by: Keerthy <j-keerthy@ti.com>
We have two further uses of raw string usage in the test/py codebase
that are used under CI. The first of which is under the bind test and
is a direct update. The second of which is to strip VT100 codes from
the match buffer. While switching this to a raw string is also a direct
update, the comment it notes that problems were encountered on Ubuntu
14.04 (and whatever Python 2 version that was) that required slight
tweaks to the regex. Replace that now that we're saying Python 3.5 is
the minimum.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Simon Glass <sjg@chromium.org> [on sandbox]
Signed-off-by: Tom Rini <trini@konsulko.com>
