This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Kontron SMARC-sAL28 board uses that flash.
This is the same change as in the linux commit f3418718c0ec ("mtd:
spi-nor: Add support for w25q32jwm").
Signed-off-by: Michael Walle <michael@walle.cc>
Reported-by: Leo Krueger <leo.krueger@zal.aero>
onenand_probe() function is missing to set mtd->type. So set same type as
which sets onenand Linux kernel driver.
After this change 'mtd list' prints correct type instead of 'Unknown'.
Signed-off-by: Pali Rohár <pali@kernel.org>
- Armada 8k: Add NAND support via PXA3xx NAND driver (Baruch)
- Armada 8k: Use ATF serdes init instead of the "old" U-Boot version
(Baruch)
- Minor update to Octeon TX/TX2 defconfig (Stefan)
Based on Linux kernel commit fc256f5789cb ("mtd: nand: pxa3xx: enable
NAND controller if the SoC needs it"). This commit adds support for the
Armada 8040 nand controller.
The kernel commit says this:
Marvell recent SoCs like A7k/A8k do not boot with NAND flash
controller activated by default. Enabling the controller is a matter
of writing in a system controller register that may also be used for
other NAND related choices.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Shmuel Hazan <shmuel.h@siklu.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
The kfree() call is unreachable, and is not needed. Remove this call and
the fail_disable_clk label.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Use the generic DT code to find the device compatible property for us.
This makes the driver look more like other current drivers. It also make
it easier to add support for other variants like Armada 8K in a future
commit.
Signed-off-by: Shmuel Hazan <shmuel.h@siklu.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Use tabs to be aligned with the rest of the code.
Fixes: 658df8bd94 ("mtd: spi-nor-core: Add octal mode support")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Adds support for NAND controllers found on OcteonTX or
OcteonTX2 SoC platforms. Also includes driver to support
Hardware ECC using BCH HW engine found on these platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The cfi-flash driver uses an open-coded version of the generic
algorithm to decode and translate multiple frames of a "reg" property.
This starts off the wrong foot by using the address-cells and size-cells
properties of *this* very node, and not of the parent. This somewhat
happened to work back when we were using a wrong default size of 2,
but broke about a year ago with commit 0ba41ce1b7 ("libfdt: return
correct value if #size-cells property is not present").
Instead of fixing the reinvented wheel, just use the generic function
that does all of this properly.
This fixes U-Boot on QEMU (-arm64), which was crashing due to decoding
a wrong flash base address:
DRAM: 1 GiB
Flash: "Synchronous Abort" handler, esr 0x96000044
elr: 00000000000211dc lr : 00000000000211b0 (reloc)
elr: 000000007ff5e1dc lr : 000000007ff5e1b0
x0 : 00000000000000f0 x1 : 000000007ff5e1d8
x2 : 000000007edfbc48 x3 : 0000000000000000
x4 : 0000000000000000 x5 : 00000000000000f0
x6 : 000000007edfbc2c x7 : 0000000000000000
x8 : 000000007ffd8d70 x9 : 000000000000000c
x10: 0400000000000003 x11: 0000000000000055
^^^^^^^^^^^^^^^^
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stefan Roese <sr@denx.de>
When possible use DMA for reading from CFI flash, this provides upto 5x
improvement in read performance with high speed CFI compliant flashes
like HyperFlash.
Code will gracefully fallback to CPU copy when DMA is unavailable.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This member was presumably dropped when this driver was converted from
Linux. However, it is still used in log statements during initialization.
This patch adds the member back. In addition, allocation of struct
vf610_nfc has been moved to the callers of vf610_nfc_nand_init. This allows
it to be allocated by DM (if it is being used) and for dev to be
initialized.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
There are too many levels of indirection when calling dev_err. This is an
artifact of the conversion of brcmnand_host.pdev from a struct
platform_device (which has a member `dev` pointing to a struct device) to
struct udevice.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Use mtd_info to get a device to log with.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Get it from spinand->slave->dev. Another option would be to use
spinand_to_mtd(spinand)->dev, but this is what the existing code uses.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This fixes dev_xxx() not always being called with a device. In
spi_nor_reg_read, a the slave device may not always be available, so we use
bus and cs instead.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This header is needed so struct udevice can be used in dev_xxx().
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Usually the device is gotten from sunxi_nfc. This is a struct device and
not a struct udevice, but the whole driver seems to be written wihout DM
anyway...
In a few instances, this patch modifies functions to take an nfc to log
with. In once instance we use mtd_info's device since there is no nfc.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Use the device from any mtd already available, or from the active mtd via
pxa3xx_nand_info if one is not.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Fix a typo
%s/interract/interact/
Use Samsung's capitalization of their trademarks
%s/onenand/OneNAND/
%s/Hyperflash/HyperFlash/
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
[trini: Add other Hyperflash cases as noted by Stefan]
Signed-off-by: Tom Rini <trini@konsulko.com>
Some of Marvell A3700 boards use mx25u12835f, specifically uDPU
and ESPRESSObin v7.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
[a.heider: adapt commit message to mainline]
Signed-off-by: Andre Heider <a.heider@gmail.com>
NAND_ARASAN selecting DM_MTD uunconditionally. Driver can be enabled with
!DM that's why Kconfig it showing it as error:
WARNING: unmet direct dependencies detected for DM_MTD
Depends on [n]: DM [=n]
Selected by [y]:
- NAND_ARASAN [=y] && MTD_RAW_NAND [=y]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The most of drivers are using '_' instead of '-' in driver name. That's why
sync up these names to be aligned. It looks quite bad to see both in use.
It is visible via dm tree command.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Nand writes should skip the bad blocks with "nand write" command.
In case of bad blocks with above 32-bit address, nand_block_isbad()
returns false due to truncated bad block address.
In below code segment,
if (nand_block_isbad(mtd, offset & ~(mtd->erasesize - 1)))
offset is 64-bit and mtd->erasesize is 32-bit, hence the truncation is
happening. Cast 'mtd->erasesize' with loff_t to fix this issue.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
FMC2 EBI support has been added. Common resources (registers base
address and clock) can now be shared between the 2 drivers using
"st,stm32mp1-fmc2-nfc" compatible string. It means that the
common resources should now be found in the parent device when EBI
node is available.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch renames functions and local variables.
This cleanup is done to get all functions starting by stm32_fmc2_nfc
in the FMC2 raw NAND driver when all functions will start by
stm32_fmc2_ebi in the FMC2 EBI driver.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
FMC2_TIMEOUT_5S will be used each time that we need to wait.
It was seen, during stress tests in an overloaded system,
that we could be close to 1 second, even if we never met this
value. To be safe, FMC2_TIMEOUT_MS is set to 5 seconds.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Remove inline comments that are useless since function label are
self explanatory.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The chip select defined in the device tree could only be 0 or 1.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
In the unlikely event that both blocks 10 and 11 are marked as bad (on a
32 bit machine), then the process of marking block 10 as bad stomps on
cached entry for block 11. There are (of course) other examples.
Signed-off-by: Patrick Doyle <pdoyle@irobot.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
The -ENODEV error value in spi_nor_read_id() is incorrect since there
clearly is a device - it just cannot be supported. Use -ENOMEDIUM instead
which has the virtue of being less common.
Fix the return value in spi_nor_scan().
Also there are a few printf() statements which should be debug() since
they bloat the code with unused strings at present. Fix those while here.
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases SPL needs to be able to erase but TPL just needs to read.
Allow these to have separate settings for SPI_FLASH_TINY.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add device table for new Micron SPI NAND devices, which have multiple
dies.
Also, enable support to select the dies.
Signed-off-by: Shivamurthy Shastri <sshivamurthy@micron.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Add SPINAND_HAS_CR_FEAT_BIT flag to identify the SPI NAND device with
the Continuous Read mode.
Some of the Micron SPI NAND devices have the "Continuous Read" feature
enabled by default, which does not fit the subsystem needs.
In this mode, the READ CACHE command doesn't require the starting column
address. The device always output the data starting from the first
column of the cache register, and once the end of the cache register
reached, the data output continues through the next page. With the
continuous read mode, it is possible to read out the entire block using
a single READ command, and once the end of the block reached, the output
pins become High-Z state. However, during this mode the read command
doesn't output the OOB area.
Hence, we disable the feature at probe time.
Signed-off-by: Shivamurthy Shastri <sshivamurthy@micron.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Add device table for M79A and M78A series Micron SPI NAND devices.
Signed-off-by: Shivamurthy Shastri <sshivamurthy@micron.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Add the SPI NAND device MT29F2G01ABAGD series number, size and voltage
details as a comment.
Signed-off-by: Shivamurthy Shastri <sshivamurthy@micron.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
In order to add new Micron SPI NAND devices, we generalized the OOB
layout structure and function names.
Signed-off-by: Shivamurthy Shastri <sshivamurthy@micron.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
The types of "offset" and "size" of "struct mtd_partition" are uint64_t,
while mtd_parse_partitions() uses int to work with these values. When
the offset reaches 2GB, it is interpreted as a negative value, which
leads to error messages like
mtd: partition "<partition name>" is out of reach -- disabled
eg. when using the "ubi part" command.
Fix this by using uint64_t for cur_off and cur_sz.
Signed-off-by: Martin Kaistra <martin.kaistra@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Fixed delay 200us is not working in certain platforms. Change to
poll for reset completion status to have more reliable reset process.
Controller will set the rst_comp bit in intr_status register after
controller has completed its reset and initialization process.
Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Radu Bacrau <radu.bacrau@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Always put the controller in reset, then take it out of reset.
This is to make sure controller always in reset state in both SPL and
proper Uboot.
This is preparation for the next patch to poll for reset completion
(rst_comp) bit after reset.
Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Radu Bacrau <radu.bacrau@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently when using OF_PLATDATA the binding between devices and drivers
is done trying to match the compatible string in the node with a driver
name. However, usually a single driver supports multiple compatible strings
which causes that only devices which its compatible string matches a
driver name get bound.
To overcome this issue, this patch adds the U_BOOT_DRIVER_ALIAS macro,
which generates no code at all, but allows an easy way to declare driver
name aliases. Thanks to this, dtoc could be improve to look for the driver
name based on its alias when it populates the U_BOOT_DEVICE entry.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When using OF_PLATDATA, the bind process between devices and drivers
is performed trying to match compatible string with driver names.
However driver names are not strictly defined, and also there are different
names used when declaring a driver with U_BOOT_DRIVER, the name of the
symbol used in the linker list and the used in the struct driver_info.
In order to make things a bit more clear, rename the drivers names. This
will also help for further OF_PLATDATA improvements, such as checking
for valid driver names.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a fix for sandbox of-platdata to avoid using an invalid ANSI colour:
Signed-off-by: Simon Glass <sjg@chromium.org>
Compiling drivers/mtd/spi/sandbox.c fails when compiled with
CONFIG_LOG=n:
In file included from include/common.h:20,
from drivers/mtd/spi/sandbox.c:13:
drivers/mtd/spi/sandbox.c:295:15: error: format ‘%s’ expects argument of
type ‘char *’, but argument 7 has type ‘int’ [-Werror=format=]
295 | log_content(" cmd: transition to %s state\n",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/printk.h:37:21: note: in definition of macro ‘pr_fmt’
37 | #define pr_fmt(fmt) fmt
| ^~~
include/log.h:128:30: note: in expansion of macro ‘log_nop’
128 | #define log_content(_fmt...) log_nop(LOG_CATEGORY, \
| ^~~~~~~
drivers/mtd/spi/sandbox.c:295:3: note: in expansion of macro
‘log_content’
295 | log_content(" cmd: transition to %s state\n",
| ^~~~~~~~~~~
drivers/mtd/spi/sandbox.c:295:37: note: format string is defined here
295 | log_content(" cmd: transition to %s state\n",
| ~^
| |
| char *
| %d
Supply function sandbox_sf_state_name() independent of CONFIG_LOG.
Fixes: c3aed5db59 ("sandbox: spi: Add more logging")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable QE bit for ISSI flash chips.
QE enablement logic is similar to what Macronix
has, so reuse the existing code itself.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The offset at which the image to be loaded from NAND is located is
retrieved from the itb header. The presence of bad blocks in the area
of the NAND where the itb image is located could invalidate the offset
which must therefore be adjusted taking into account the state of the
sectors concerned.
cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
This change allows more fine tuning of driver model based SPI support in
SPL and TPL. It is now possible to explicitly enable/disable the DM_SPI
support in SPL and TPL via Kconfig option.
Before this change it was necessary to use:
/* SPI Flash Configs */
#if defined(CONFIG_SPL_BUILD)
#undef CONFIG_DM_SPI
#undef CONFIG_DM_SPI_FLASH
#undef CONFIG_SPI_FLASH_MTD
#endif
in the ./include/configs/<board>.h, which is error prone and shall be
avoided when we strive to switch to Kconfig.
The goal of this patch:
Provide distinction for DM_SPI support in both U-Boot proper and SPL (TPL).
Valid use case is when U-Boot proper wants to use DM_SPI, but SPL must
still support non DM driver.
Another use case is the conversion of non DM/DTS SPI driver to support
DM/DTS. When such driver needs to work in both SPL and U-Boot proper, the
distinction is needed in Kconfig (also if SPL version of the driver
supports OF_PLATDATA).
In the end of the day one would have to support following use cases (in
single driver file - e.g. mxs_spi.c):
- U-Boot proper driver supporting DT/DTS
- U-Boot proper driver without DT/DTS support (deprecated)
- SPL driver without DT/DTS support
- SPL (and TPL) driver with DT/DTS (when the SoC has enough resources to
run full blown DT/DTS)
- SPL driver with DT/DTS and SPL_OF_PLATDATA (when one have constrained
environment with no fitImage and OF_LIBFDT support).
Some boards do require SPI support (with DM) in SPL (TPL) and some only
have DM_SPI{_FLASH} defined to allow compiling SPL.
This patch converts #ifdef CONFIG_DM_SPI* to #if CONFIG_IS_ENABLED(DM_SPI)
and provides corresponding defines in Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[trini: Fixup a few platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
dm_spi_slave_platdata used in sf_probe for printing
plat->cs value and there is no relevant usage apart
from this.
We have enough debug messages available in SPI and SF
areas so drop this plat get and associated bug statement.
Cc: Simon Glass <sjg@chromium.org>
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Currently spi-nor code is assigning _write ops for SST
and other flashes separately.
Just call the sst_write from generic write ops and return
if SST flash found, this way it avoids the confusion of
multiple write ops assignment during the scan and makes
it more feasible for code readability.
No functionality changes.
Cc: Simon Glass <sjg@chromium.org>
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The get_sw_write_prot API is used to get the write-protected
bits of flash by reading the status register and other wards
it's API for reading register bits.
1) This kind of requirement can be achieved using existing
flash operations and flash locking API calls instead of
making a separate flash API.
2) Technically there is no real hardware user for this API to
use in the source tree.
3) Having a flash operations API for simple register read bits
also make difficult to extend the flash operations.
4) Instead of touching generic code, it is possible to have
this functionality inside spinor operations in the form of
flash hooks or fixups for associated flash chips.
Considering all these points, this patch drops the get_sw_write_prot
and associated code bases.
Cc: Simon Glass <sjg@chromium.org>
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Use CONFIG_IS_ENABLED to prevent ifdef in sf_probe.c
Cc: Simon Glass <sjg@chromium.org>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add support for new Kioxia products.
The new Kioxia products support program load x4 command, and have
HOLD_D bit which is equivalent to QE bit.
Signed-off-by: Yoshio Furuyama <ytc-mb-yfuruyama7@kioxia.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/aa69e455beedc5ce0d7141359b9364ed8aec9e65.1584949601.git.ytc-mb-yfuruyama7@kioxia.com
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The suffix was changed from "G" to "J" to classify between 1st generation
and 2nd generation serial NAND devices (which now belong to the Kioxia
brand).
As reference that's
1st generation device of 1Gbit product is "TC58CVG0S3HRAIG"
2nd generation device of 1Gbit product is "TC58CVG0S3HRAIJ".
The 8Gbit type "TH58CxG3S0HRAIJ" is new to Kioxia's serial NAND lineup and
the prefix was changed from "TC58" to "TH58".
Thus the functions were renamed from tc58cxgxsx_*() to tx58cxgxsxraix_*().
Signed-off-by: Yoshio Furuyama <ytc-mb-yfuruyama7@kioxia.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/0dedd9869569a17625822dba87878254d253ba0e.1584949601.git.ytc-mb-yfuruyama7@kioxia.com
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[ Linux commit 9afbe7c0140f663586edb6e823b616bd7076c00a ]
If the write protect signal from this IP is connected to the NAND
device, this IP can handle the WP# pin via the WRITE_PROTECT
register.
The Denali NAND Flash Memory Controller User's Guide describes
this register like follows:
When the controller is in reset, the WP# pin is always asserted
to the device. Once the reset is removed, the WP# is de-asserted.
The software will then have to come and program this bit to
assert/de-assert the same.
1 - Write protect de-assert
0 - Write protect assert
The default value is 1, so the write protect is de-asserted after
the reset is removed. The driver can write to the device unless
someone has explicitly cleared register before booting the kernel.
The boot ROM of some UniPhier SoCs (LD4, Pro4, sLD8, Pro5) is the
case; the boot ROM clears the WRITE_PROTECT register when the system
is booting from the NAND device, so the NAND device becomes read-only.
Set it to 1 in the driver in order to allow the write access to the
device.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This CONFIG option is only used in denali_spl.c
Move it close to SPL_NAND_DENALI, and make it depend on SPL_NAND_DENALI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is bad practice to include common.h in other header files since it can
bring in any number of superfluous definitions. It implies that some C
files don't include it and thus may be missing CONFIG options that are set
up by that file. The C files should include these themselves.
Update some header files in arch/arm to drop this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this uncommon header out of the common header.
Fix up some style problems in flash.h while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
On i.mx7ulp EVK board, we use MX25R6435F NOR flash, add its parameters
and IDs to flash parameter array. Otherwise, the flash probe will fails.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Probably the non-use of the device parameter by the print routines did
not generate compilation errors.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Add more BCH setting mode and remove the unnecessary platform constrain
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To enable the Randomizer module, set GPMI_ECCCTRL[RANDOMIZER_ENABLE] to
1, then set GPMI_ECCCOUNT[RANDOMIZER_PAGE] to select randomizer page
number needed to be randomized.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When enabled randomizer during ECC reading, the controller reported it's
erased page. Checking zero count will cause data get modified to all
0xFF. Stop checking during randomizer to workaround this issue.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since iMX8 has enabled clock uclass, we can parse the clocks from DTB
and enable them in GPMI driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
enable the GPMI NAND driver for i.MX8, i.MX8 use similar controller as
i.MX8M
- register definition for i.mx8
- DMA structure must be 32bit address
Signed-off-by: Peng Fan <peng.fan@nxp.com>
imx8mm needs to BCH encode and set NAND page number needed to be
randomized
modify conditional compilation
Use CONFIG_IMX8M, so it apply to imx8mq/mm/mn
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The iMX6SX uses compatible string "fsl,imx6sx-gpmi-nand" for gpmi
node in DTS, so update the driver for the string
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update the mini driver to add support for getting ecc info from ONFI and
support read image data from page unaligned NAND address.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update the gpmi/apbh_dma/bch drivers and relevant registers for i.MX8M.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch is a porting of
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/
commit/?h=imx_4.1.15_1.0.0_ga&id=e4dacc44d22e9474ec456cb330df525cd805ea38
"
i.MX6QP and i.MX7D BCH module integrated a new feature to detect the
bitflip number for erased NAND page. So for these two platform, set the
erase threshold to gf/2 and if bitflip detected, GPMI driver will
correct the data to all 0xFF.
Also updated the imx6qp dts file to ditinguish the GPMI module for i.MX6Q
with the one for i.MX6QP.
"
In this patch, i.MX6UL is added and threshold changed to use ecc_strength.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch is porting from linux:
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/commit/
?h=imx_4.1.15_1.0.0_ga&id=3d42fcece496224fde59f9343763fb2dfc5b0768
"
We may meet the bitflips in reading an erased page(contains all 0xFF),
this may causes the UBIFS corrupt, please see the log from Elie:
-----------------------------------------------------------------
[ 3.831323] UBI warning: ubi_io_read: error -74 (ECC error) while reading 16384 bytes from PEB 443:245760, read only 16384 bytes, retry
[ 3.845026] UBI warning: ubi_io_read: error -74 (ECC error) while reading 16384 bytes from PEB 443:245760, read only 16384 bytes, retry
[ 3.858710] UBI warning: ubi_io_read: error -74 (ECC error) while reading 16384 bytes from PEB 443:245760, read only 16384 bytes, retry
[ 3.872408] UBI error: ubi_io_read: error -74 (ECC error) while reading 16384 bytes from PEB 443:245760, read 16384 bytes
...
[ 4.011529] UBIFS error (pid 36): ubifs_recover_leb: corrupt empty space LEB 27:237568, corruption starts at 9815
[ 4.021897] UBIFS error (pid 36): ubifs_scanned_corruption: corruption at LEB 27:247383
[ 4.030000] UBIFS error (pid 36): ubifs_scanned_corruption: first 6569 bytes from LEB 27:247383
-----------------------------------------------------------------
This patch does a check for the uncorrectable failure in the following steps:
[0] set the threshold.
The threshold is set based on the truth:
"A single 0 bit will lead to gf_len(13 or 14) bits 0 after the BCH
do the ECC."
For the sake of safe, we will set the threshold with half the gf_len, and
do not make it bigger the ECC strength.
[1] count the bitflips of the current ECC chunk, assume it is N.
[2] if the (N <= threshold) is true, we continue to read out the page with
ECC disabled. and we count the bitflips again, assume it is N2.
(We read out the whole page, not just a chunk, this makes the check
more strictly, and make the code more simple.)
[3] if the (N2 <= threshold) is true again, we can regard this is a erased
page. This is because a real erased page is full of 0xFF(maybe also has
several bitflips), while a page contains the 0xFF data will definitely
has many bitflips in the ECC parity areas.
[4] if the [3] fails, we can regard this is a page filled with the '0xFF'
data.
"
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Provide an option in DT to use legacy bch geometry, which compatible
with the 3.10 kernel bch setting. To enable the feature, adding
"fsl,legacy-bch-geometry" under gpmi-nand node.
NOTICE: The feature must be enabled/disabled in both u-boot and kernel.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The code change updated the NAND driver BCH ECC layout algorithm to
support large oob size NAND chips(oob > 1024 bytes) and proposed a new
way to set ECC layout.
Current implementation requires each chunk size larger than oob size so
the bad block marker (BBM) can be guaranteed located in data chunk. The
ECC layout always using the unbalanced layout(Ecc for both meta and
Data0 chunk), but for the NAND chips with oob larger than 1k, the driver
cannot support because BCH doesn’t support GF 15 for 2K chunk.
The change keeps the data chunk no larger than 1k and adjust the ECC
strength or ECC layout to locate the BBM in data chunk. General idea for
large oob NAND chips is
1.Try all ECC strength from the minimum value required by NAND spec to
the maximum one that works, any ECC makes the BBM locate in data chunk
can be chosen.
2.If none of them works, using separate ECC for meta, which will add one
extra ecc with the same ECC strength as other data chunks. This extra
ECC can guarantee BBM located in data chunk, of course, we need to check
if oob can afford it.
Previous code has two methods for ECC layout setting, the
legacy_calc_ecc_layout and calc_ecc_layout_by_info, the difference
between these two methods is, legacy_calc_ecc_layout set the chunk size
larger chan oob size and then set the maximum ECC strength that oob can
afford. While the calc_ecc_layout_by_info set chunk size and ECC
strength according to NAND spec. It has been proved that the first
method cannot provide safe ECC strength for some modern NAND chips, so
in current code,
1. Driver read NAND parameters first and then chose the proper ECC
layout setting method.
2. If the oob is large or NAND required data chunk larger than oob size,
chose calc_ecc_for_large_oob, otherwise use calc_ecc_layout_by_info
3. legacy_calc_ecc_layout only used for some NAND chips does not contains
necessary information. So this is only a backup plan, it is NOT
recommended to use these NAND chips.
Signed-off-by: Han Xu <b45815@freescale.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move CONFIG_SYS_MTDPARTS_RUNTIME into Kconfig done by moveconfig.py.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Spansion "s25fs512s" flash is incorrectly decoded as "s25fl512s" on
various platforms as former is not present. Add the entry.
Linux already has both the flashes present. A snippet below:
{ "s25fl512s", INFO6(0x010220, 0x4d0080, 256 * 1024, 256...},
{ "s25fs512s", INFO6(0x010220, 0x4d0081, 256 * 1024, 256...},
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
IS25WP256 flash chips do support 4byte address opcodes,
so enable support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Sagar Kadam <sagar.kadam@sifive.com>
Enable QE bit for ISSI flash chips.
QE enablement logic is similar to what Macronix
has, so reuse the existing code itself.
Cc: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Toshiba recently launched new revisions of their serial SLC NAND series.
TC58CVG2S0HRAIJ is a refresh of previous series with minor improvements.
Basic parameters are same so lets add support for this new revision.
Datasheet: https://business.kioxia.com/info/docget.jsp?did=58601&prodName=TC58CVG2S0HRAIJ
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Linux has good support for Toshiba SPI-NAND, so lets import it.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The s25fl256s0 supports dual and quad read like s25fl256s1.
Enable it by adding SPI_NOR_DUAL_READ and SPI_NOR_QUAD_READ
flags to the flash_info entry.
Tested on real silicon and confirmed to be working.
Signed-off-by: Bacem Daassi <Bacem.Daassi@cypress.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
hweight32 is a somewhat expensive way to check for power-of-2. Use the
is_power_of_2 helper, which does the standard and cheap idiom
foo&(foo-1)==0.
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-96 (-96)
Function old new delta
spi_nor_write 388 292 -96
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Linux Broadcom NAND driver only disabled clock if no childs are initialized.
This section of the code seems to have been accidentally dropped when it was
imported in U-Boot.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The end_cmd field in the variables cmd_phase_addr and data_phase_addr
contains the value 0xFF when the end_cmd equals NAND_CMD_NONE. This
should be 0x00.
This is caused by comparing NAND_CMD_NONE (int) with end_cmd (u8).
end_cmd will be promoted by the int value -1 and therefore is not equal
to 0xFF. Solved by casting NAND_CMD_NONE to u8 which will avoid int
promotion.
Signed-off-by: Patrick van Gelder <patrick.vangelder@nl.bosch.com>
Reviewed-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Commit 6293b0361d ("mtd: nand: pxa3xx: add raw read support") added the
local data_len variable in handle_data_pio() to track read size, but
forgot to update the condition of drain_fifo() call. That happens to
work when the layout last_chunk_size != 0. But when last_chunk_size ==
0, drain_fifo() is not called to read the last chunk, which leads to
"Wait timeout!!!" error. Fix this.
Fixes: 6293b0361d ("mtd: nand: pxa3xx: add raw read support")
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
There is no reason to continue when DT status property indicates that NAND
flash is disabled. But that means that NOR flash should be present that's
why try it find it out.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
xnand structure is private data structure and it is handled by core and
probe shouldn't touch it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Fixed wrong enumeration of nand_config structure. Added chip select
function before reading the nand chip for maf/dev id's, without this
unable to access id's from some of the micron chips. Also added a
print statement to identify if a nand flash is using on-die ecc.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The implementation of dma_map_single() and dma_unmap_single() is
exactly the same for all the architectures that support them.
Factor them out to <linux/dma-mapping.h>, and make all drivers to
include <linux/dma-mapping.h> instead of <asm/dma-mapping.h>.
If we need to differentiate them for some architectures, we can
move the generic definitions to <asm-generic/dma-mapping.h>.
Add some comments to the helpers. The concept is quite similar to
the DMA-API of Linux kernel. Drivers are agnostic about what is
going on behind the scene. Just call dma_map_single() before the
DMA, and dma_unmap_single() after it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This function name conflicts with our desire to #define free() to
something else on sandbox. Since it deals with resources, rename it to
rfree().
Signed-off-by: Simon Glass <sjg@chromium.org>
UCLASS_MTD is a better fit for NAND drivers.
Make NAND_DENALI_DT depend on DM_MTD, which is needed to compile
drivers/mtd/mtd-uclass.c
Also, make ARCH_UNIPHIER select DM_MTD because all the defconfig
of this platform enables NAND_DENALI_DT.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently, the denali NAND driver in U-Boot configures the
SPARE_AREA_SKIP_BYTES based on the CONFIG option.
Recently, Linux kernel merged a patch that associates the proper
value for this register with the DT compatible string.
Do likewise in U-Boot too.
The denali_spl.c still uses CONFIG_NAND_DENALI_SPARE_AREA_SKIP_BYTES.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When the reset signal is de-asserted, the HW-controlled bootstrap
starts running unless it is disabled in the SoC integration.
It issues some commands to detect a NAND chip, and sets up registers
automatically. Until this process finishes, software should avoid
any register access.
Without this delay function, some of UniPhier boards hangs up while
executing nand_scan_ident(). (denali_read_byte() is blocked)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Denali NAND driver in mainline Linux currently cannot deassert the
reset. The upcoming Linux 5.6 will support the reset controlling, and
also set up SPARE_AREA_SKIP_BYTES correctly. So, the Denali driver in
the future kernel will work without relying on any bootloader or firmware.
However, we still need to take care of stable kernel versions for a while.
U-boot should not assert the reset of this controller.
Fixes: ed784ac382 ("mtd: rawnand: denali: add reset handling")
Signed-off-by: Marek Vasut <marex@denx.de>
[yamada.masahiro: reword the commit description]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The "nand_x" and "ecc" clocks are currently optional. Make the core
clock optional in the same way. This will allow platforms with no clock
driver support to use this driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Marek Vasut <marex@denx.de> # On SoCFPGA Arria V
On Altera SoCFPGA, upon either cold-boot or power-on reset, the
Denali NAND IP is initialized by the BootROM ; upon warm-reset,
the Denali NAND IP is NOT initialized by BootROM. In fact, upon
warm-reset, the SoCFPGA BootROM checks whether the SPL image in
on-chip RAM is valid and if so, completely skips re-loading the
SPL from the boot media.
This does sometimes lead to problems where the software left
the boot media in inconsistent state before warm-reset, and
because the BootROM does not reset the boot media, the boot
media is left in this inconsistent state, often until another
component attempts to access the boot media and fails with an
difficult to debug failure. To mitigate this problem, the SPL
on Altera SoCFPGA always resets all the IPs on the SoC early
on boot.
This results in a couple of register values, pre-programmed by
the BootROM, to be lost during this reset. To restore correct
operation of the IP on SoCFPGA, these values must be programmed
back into the controller by the driver. Note that on other SoCs
which do not use the HW-controlled bootstrap, more registers
may have to be programmed.
This also aligns the SPL behavior with the full Denali NAND
driver, which sets these values in denali_hw_init().
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add support for Octal flash devices. Octal flash devices use 8 IO lines
for data transfer. Currently only 1-1-8 Octal Read mode is supported.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Linux has supported W25N01GV for a long time, so lets import it.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Drop local dma_map_single() and dma_unmap_single() and use arch specific
common implementation
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove hardcoded base addresses of smc controller and nand controller.
Get those addresses from dt and replace wherever they are used.
Remove smc and nand base address from header file too.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove hardcoded base address of nand and replace it with the
value taken from device tree. Remove base address from header
file too.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Make changes to arasan nand driver to move it to driver model.
Select DM_MTD if arasan nand driver is selected.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeFDfVAAoJEB6zHgIOrC/IKfsH/2cUfXuc9IgA7L90L3g7htlS
zLAQSC8Xk0WbgbmBJh/lq6zFWj2Mu2yfkZqRzwN8bHkmOPq40F+pEAszVtjH77HM
FpSjMSDVWfNXuhmoiS571dehA0TGi1b2kknrAXqpOwVuMRncMCwaPi8yZYZSGlSV
VzMtguQxD0sZg4oMZVde3tCd41smPTPNDjzLZnXdLa0b09+EtW6enGuk3vzXlS/8
QUT68wUzkeoptJhf3pQ3BXNvkFwdNdYJ74uevDmkAYtvxyl10WNykcwYmH50Q9qq
9plF11EizmTHlj16rWpZLx66RP0s4pziKaeGMr6S8uln33Cr9N496wPqtuDBnvA=
=FYPj
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.04-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features for 2020.04 cycle
This feature set is a patch series from Tudor Ambarus which includes
parsing of the spi flash SFDP parser for SST flashes, and using those
tables to retrieve unique saved per device MAC address. This is then
used as base mac address on the SAMA5D2 Wireless SOM EK board.
Bring in the following merges:
commit 8fbbec12f7
Merge: 87f69f467a63618e71e8
Author: Tom Rini <trini@konsulko.com>
Date: Fri Jan 3 09:48:47 2020 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq into next
- updates and fixes on ls1028a, lx2, ls1046a, MC-DPSPARSER support
commit 87f69f467a
Merge: c0912f9bbf4466b99703
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 24 08:18:19 2019 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx into next
- Enable DM driver on ppc/km boards
- Enable DM_USB for some of NXP powerpc platforms: P5040, T4240, T208x,
T104x, P4080, P2041, P2020, P1020, P3041
- Some updates in mpc85xx-ddr driver, km boards
commit c0912f9bbf
Merge: 533c9f5714a1d6dc3f84
Author: Tom Rini <trini@konsulko.com>
Date: Wed Dec 18 07:20:19 2019 -0500
Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-x86 into next
- Various x86 common codes updated for TPL/SPL
- I2C designware driver updated for PCI
- ICH SPI driver updated to support Apollo Lake
- Add Intel FSP2 base support
- Intel Apollo Lake platform specific drivers support
- Add a new board Google Chromebook Coral
commit 533c9f5714
Merge: 553cb06887033e18b47b
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 17 07:53:08 2019 -0500
Merge tag '20191217-for-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next
i2c: for next
- misc: i2c_eeprom:
Add partition support and add ability to query size
of eeprom device and partitions
- i2c common:
add support for offset overflow in to address and add
sandbox tests for it.
commit 553cb06887
Merge: f39abbbc53b4f98b3b16
Author: Tom Rini <trini@konsulko.com>
Date: Thu Dec 12 08:18:59 2019 -0500
Merge tag 'dm-next-13dec19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm into next
buildman improvements including toolchain environment feature
sandbox unicode support in serial
Static checker warns 'ret' variable may be used uninitialized in
spi_nor_erase() and spi_nor_write() in case of zero length requests.
Fix these warnings by checking for zero length requests and returning
early.
Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add gd25q128 128Mbit chip to spi-nor id table.
Tested on Pinebook Pro
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # roc-rk3399-pc
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
JESD216 allow vendors to define their own SFDP tables.
Add SST SFDP parser. The vendor table is allocated using resource-managed
kmalloc - the table will be freed on driver detach. It will be accessible
by getting the UCLASS_SPI_FLASH's private data.
The SST's SFDP table is particularly of interest because contains
pre-programmed globally unique EUI-48 and EUI-64 identifiers.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
With of-platdata we need to create drivers for particular chips, or at
least drivers that are separate from the standard code, since C structures
are created by dtoc which are private to that driver.
To avoid duplicating the probing code, export this probe function for use
by these drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Move MTD-related lines out of the root Makefile. Put them in their
respective directories. Enclose some of these new lines to skip them
when building the SPL. MTD core files and some MTD device drivers are
compiled in a mtd.o object and included in the final object only if
MTD support is required (there are two different symbols for that, one
for U-Boot and one for the SPL).
Now that all defconfigs have been fixed, we can stop the logic where
enabling a command selects the core files to compile. This logic is
broken since selecting a symbol with a 'depends on' will not enforce
this secondary dependency.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The 'sf' command is not supposed to rely on the MTD stack, but both
'sf' and 'nand' commands use helpers located in mtd_uboot.c. Despite
their location, these functions do not depend at all on the MTD
stack.
This file (drivers/mtd/mtd_uboot.c) is only compiled if CONFIG_MTD is
selected, which is inconsistent with the current situation. Solve this
by moving these three functions (which are only used by the above two
commands) out of mtd_uboot.c and put them in a C file only compiled
with cmd/sf.c and cmd/nand.c.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Don't export get_part function now]
Signed-off-by: Tom Rini <trini@konsulko.com>
It is already the case that all defconfigs with SPI_FLASH_MTD also
declare using MTD, but let's make this consistent and enforce it in
Kconfig. Most of the time SPI_FLASH_MTD is used in conjunction with
UBI, which already depends on MTD.
Suggested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Because of the include's game, when some files are compiled for a SPI
NAND device, no warning appears. But when it is for a raw NAND device,
GCC complains. Fix these warning by including <common.h>.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Like in Linux, just use CONFIG_MTD to compile the MTD stack.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
CONFIG_MTD must be reserved for the MTD core. Like any other
subsystem, prefix the symbol by DM when it comes to DM support.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
[trini: Add Kconfig files]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add more clarity by changing the Kconfig entry name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
The array 'mtd_table' is unused in the code. Remove this as gcc doesn't
always discard unused global variables.
Signed-off-by: Tom Rini <trini@konsulko.com>
These functions do not use driver model but are still used. Move them to a
new eeprom.h header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move these functions into the command.h header file which is a better fit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move these two functions into the irq_funcs.h header file. Also move
interrupt_handler_t as this is used by the irq_install_handler() function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions do not use driver model but are fairly widely used in
U-Boot. But it is not clear that they will use driver model anytime soon,
so we don't want to label them as 'legacy'.
Move them to a new irq_func.h header file. Avoid the name 'irq.h' since it
is widely used in U-Boot already.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Drop inclusion of crc.h in common.h and use the correct header directly
instead.
With this we can drop the conflicting definition in fw_env.h and rely on
the crc.h header, which is already included.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
On i.MX7 in a sake of reducing the disturbances caused by a neighboring
cells in the FCB page in the NAND chip, a randomizer is enabled when
reading the FCB page by ROM bootloader.
Add API for setting BCH to specific layout (and restoring it back) used by
ROM bootloader to be able to burn it in a proper way to NAND using
nandbcb command.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
- Add I2C clocks for i.MX6Q CCF driver
- Fix check in clk_set_default_parents()
- Managed API to get clock from device tree
- Fixes for core clock code (including sandbox regression tests)
