Commit graph

245 commits

Author SHA1 Message Date
Simon Glass
cd93d625fd common: Drop linux/bitops.h from common header
Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 21:19:23 -04:00
Simon Glass
c05ed00afb common: Drop linux/delay.h from common header
Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 21:19:23 -04:00
Simon Glass
f7ae49fc4f common: Drop log.h from common header
Move this header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 21:19:18 -04:00
Simon Glass
0914011310 command: Remove the cmd_tbl_t typedef
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.

Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.

This requires quite a few header-file additions.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 18:36:55 -04:00
Simon Glass
691d719db7 common: Drop init.h from common header
Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 17:33:33 -04:00
Simon Glass
e6f6f9e648 common: Drop part.h from common header
Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 17:33:33 -04:00
Simon Glass
0528979fa7 part: Drop disk_partition_t typedef
We should not be using typedefs and these make it harder to use
forward declarations (to reduce header file inclusions). Drop the typedef.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 17:33:33 -04:00
Simon Glass
90526e9fba common: Drop net.h from common header
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.

Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 17:33:31 -04:00
Simon Glass
c3dc39a2f8 arm: Don't include common.h in header files
It is bad practice to include common.h in other header files since it can
bring in any number of superfluous definitions. It implies that some C
files don't include it and thus may be missing CONFIG options that are set
up by that file. The C files should include these themselves.

Update some header files in arch/arm to drop this.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 14:54:24 -04:00
Samuel Holland
3988be5fd4 spl: Always define preloader_console_init
A large number of boards call preloader_console_init unconditionally.
Currently, they fail to build with CONFIG_SPL_SERIAL=n, because the
function is undefined in that case. To fix the build, always define
preloader_console_init, but make it no-op when CONFIG_SPL_SERIAL=n.

For the few boards that did check for CONFIG_SPL_SERIAL before calling
preloader_console_init, remove the checks, since the function can now
be called unconditionally.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-05-15 14:47:35 -04:00
Harald Seiler
e97590654a spl: mmc: Rename spl_boot_mode() to spl_mmc_boot_mode()
The function's name is misleading as one might think it is used
generally to select the boot-mode when in reality it is only used by the
MMC driver to find out in what way it should try reading U-Boot Proper
from a device (either using a filesystem, a raw sector/partition, or an
eMMC boot partition).

Rename it to spl_mmc_boot_mode() to make it more obvious what this
function is about.

Link: https://lists.denx.de/pipermail/u-boot/2020-April/405979.html
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2020-04-22 20:41:57 +08:00
Dario Binacchi
96b109ba74 video: omap: add support for DM/DTS
Update the driver to support the device tree and the driver model.
Timings and panel parameters are now loaded from the device tree.

The DM code replaces the am335x_lcdpanel structure with
tilcdc_panel_info taken from the linux kernel, as well the management
of additional parameters not covered in the legacy code. In addition,
the am335x_lcdpanel structure contains parameters and operations that
were probably a requirement of the board for which this driver was
developed and which, however, were not developed in the linux kernel.
All this led to rewrite th DM controller initialization code, except
for the pixel clock setting that is executed in a function created in a
previous patch with code taken from the legacy am335xfb_init.

The patch has been tested on a custom board with u-boot 2018.11-rc2 and
the following device-tree configuration:

	panel {
		compatible = "ti,tilcdc,panel";
		pinctrl-names = "default";
		pinctrl-0 = <&lcd_enable_pins>;
		enable-gpios = <&gpio0 31 0>;
		backlight = <&backlight>;
		status = "okay";
		u-boot,dm-pre-reloc;
		panel-info {
			ac-bias           = <255>;
			ac-bias-intrpt    = <0>;
			dma-burst-sz      = <16>;
			bpp               = <16>;
			fdd               = <0x80>;
			sync-edge         = <0>;
			sync-ctrl         = <1>;
			raster-order      = <0>;
			fifo-th           = <0>;
		};
		display-timings {
			native-mode = <&timing0>;
			timing0: 800x480 {
				hactive         = <800>;
				vactive         = <480>;
				hback-porch     = <46>;
				hfront-porch    = <210>;
				hsync-len       = <20>;
				vback-porch     = <23>;
				vfront-porch    = <22>;
				vsync-len       = <10>;
				clock-frequency = <33000000>;
				hsync-active    = <0>;
				vsync-active    = <0>;
			};
		};
	};

Signed-off-by: Dario Binacchi <dariobin@libero.it>
Tested-by: Dario Binacchi <dariobin@libero.it>
2020-03-03 13:08:14 +05:30
Tom Rini
07add22cab Merge tag '2020-01-20-ti-2020.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-ti
K3 J721E:
* DMA support.
* MMC and ADMA support.
* EEPROM support.
* J721e High Security EVM support.
* USB DT nodes

K3 AM654:
* Fixed boot due to pmic probe error.
* USB support and DT nodes.
* ADMA support

DRA7xx/AM57xx:
* BBAI board support
* Clean up of net platform code under board/ti

AM33/AM43/Davinci:
* Reduce SPL size for omap3 boards.
* SPL DT support for da850-lcdk
* PLL divider fix for AM335x
2020-01-20 14:54:55 -05:00
Dario Binacchi
1adea9cc03 arm: omap: fix MPU DPLL divisor for 800MHz clock
In locked condition CLKOUT = CLKINP * [M / (N + 1)].

Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-20 10:10:29 +05:30
Caleb Robey
b4309846db board: ti: beagleboneai: add initial support
These are necessities for beaglebone ai boot. There is the addition of
CONFIG_SUPPORT_EMMC_CONFIG to the Kconfig file. This is present upstream
but not in 19.01 yet.

Signed-off-by: Jason Kridner <jdk@ti.com>
Signed-off-by: Caleb Robey <c-robey@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-20 10:10:28 +05:30
Simon Glass
db41d65a97 common: Move hang() to the same header as panic()
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-17 17:53:40 -05:00
Simon Glass
9b4a205f45 common: Move RAM-sizing functions to init.h
These functions relate to memory init so move them into the init
header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-01-17 14:02:35 -05:00
Simon Glass
9a3b4ceb37 common: Move reset_cpu() to the CPU header
Move this function out of common.h and into a relevant header file.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-01-17 14:02:31 -05:00
Simon Glass
5e6267af31 common: Move reset_phy() to net.h
This is a network function so let's move it into that header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-01-17 13:26:50 -05:00
Simon Glass
bcee8d6764 dm: gpio: Allow control of GPIO uclass in SPL
At present if CONFIG_SPL_GPIO_SUPPORT is enabled then the GPIO uclass
is included in SPL/TPL without any control for boards. Some boards may
want to disable this to reduce code size where GPIOs are not needed in
SPL or TPL.

Add a new Kconfig option to permit this. Default it to 'y' so that
existing boards work correctly.

Change existing uses of CONFIG_DM_GPIO to CONFIG_IS_ENABLED(DM_GPIO) to
preserve the current behaviour. Also update the 74x164 GPIO driver since
it cannot build with SPL.

This allows us to remove the hacks in config_uncmd_spl.h and
Makefile.uncmd_spl (eventually those files should be removed).

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-12-15 08:52:29 +08:00
Suman Anna
1045ff4d1a ARM: DRA7: Fixup DSP OPP_HIGH clock rate on DRA76P/DRA77P SoCs
The commit 1b42ab3eda ("ARM: DRA7: Fixup DSPEVE, IVA and GPU clock
frequencies based on OPP") added the core logic to update the kernel
device-tree blob to adjust the DSP, IVA and GPU DPLL clocks based on
a one-time OPP choice selected in U-Boot for most of the DRA7xx/AM57xx
family of SoCs.

The DSPs on DRA76xP/DRA77xP SoCs (DRA76x ACD package SoCs) though
provide a higher performance and can run at a higher clock frequency
of 850 MHz at OPP_HIGH instead of 750 MHz. Fix up the logic to use the
correct clock rates on these SoCs. Note that this higher clock rate is
not applicable to other Jacinto 6 Plus SoCs (DRA75xP/DRA74xP SoCs or
AM574x SoCs) that follow the ABZ package.

Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-12-09 14:00:24 -05:00
Miquel Raynal
88718be300 mtd: rename CONFIG_NAND -> CONFIG_MTD_RAW_NAND
Add more clarity by changing the Kconfig entry name.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-03 23:04:10 -05:00
Simon Glass
1eb69ae498 common: Move ARM cache operations out of common.h
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:24:58 -05:00
Simon Glass
9edefc2776 common: Move some cache and MMU functions out of common.h
These functions belong in cpu_func.h. Another option would be cache.h
but that code uses driver model and we have not moved these cache
functions to use driver model. Since they are CPU-related it seems
reasonable to put them here.

Move them over.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:23:55 -05:00
Simon Glass
1045315df0 common: Move get_ticks() function out of common.h
This function belongs in time.h so move it over and add a comment.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:23:13 -05:00
Lokesh Vutla
5c6e497eaa arm: dra7xx: Hang on any failure during IOdelay recalibration
If there is any failure during IOdelay recalibration sequence, IOs are
not guaranteed to behave as expected. So hang on any failure during the
sequence.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11 13:32:40 -04:00
Lokesh Vutla
60e3d43a26 arm: dra7xx: Fix error path in iodelay recalibration
When an error is reported in __recalibrate_iodelay_start(), de-isolation
of IO doesn't happen. Because of this, undefined behaviour is observed
on many peripherals without any error. So make sure io is out of isolation
at the end of iodelay recalibration.

Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11 13:32:39 -04:00
Moses Christopher
b1476b52b3 am335x, guardian: update guardian board
- add BOARD_LATE_INIT function calls in board.c
  - add swi_status detection in board.c
  - mux: add guardian interfaces to single pinmux structure
  - am33xx, kconfig: add BOARD_LATE_INIT for GUARDIAN board

Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-10-11 13:31:17 -04:00
Krunal Bhargav
2b2e1573cf arm: omap: emif-common: Fix memory priming for ECC
Before the priming begins, we need to disable RMW (Read Modify Write)
and disable ECC verification for read accesses. By default, the EMIF
tool enables RMW and read accesses in the EMIF_ECC_CTRL_REG.

Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11 13:31:17 -04:00
Krunal Bhargav
d0a37a5e51 arm: omap: emif-common: Disable interleaving
If ECC is enabled, we need to ensure interleaving is disabled for higher
address space.

Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11 13:31:17 -04:00
Lokesh Vutla
ed474ae00c arm: omap: emif-common: Fix ecc address calculation
ecc_address_range registers contains the start address and end address
of the DDR address space. But the ddr driver is assuming the register
contains the start address and size of the DDR address space. Because
of this the ecc enabling is failing for the 2nd range of ecc addresses.
Fix this calculation.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11 13:31:17 -04:00
Simon Glass
27084c03d3 spl: Allow tiny printf() to be controlled in SPL and TPL
At present there is only one control for this and it is used for both SPL
and TPL. But SPL might have a lot more space than TPL so the extra cost of
a full printf() might be acceptable.

Split the option into two, providing separate SPL and TPL controls. The
TPL setting defaults to the same as SPL.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-10-08 13:57:45 +08:00
Suman Anna
a517c1f62f ARM: DRA7: Fixup DPLL clock rate fixup logic for newer kernels
The commit 1b42ab3eda ("ARM: DRA7: Fixup DSPEVE, IVA and GPU clock
frequencies based on OPP") updates the kernel device-tree blob to adjust
the DSP, IVA and GPU DPLL clocks based on a one-time OPP choice selected
in U-Boot. All these DPLL clocks are children of the cm_core_aon clocks
DT node.

The hierarchy of this clocks DT node has changed in newer Linux kernels
starting from v5.0, and this results in a failure in ft_fixup_clocks()
function to update the clock rates on these newer kernels. Fix this by
updating the lookup logic to look through both the newer and older
DT hierarchy paths for the cm_core_aon clocks node.

Signed-off-by: Suman Anna <s-anna@ti.com>
2019-08-20 11:46:38 -04:00
Tom Rini
9c6115822e Merge branch '2019-08-11-ti-imports'
- More DaVinci updates and fixes
- PCIe support on am65x
- Watchdog converted to DM
- Assorted other bugfixes
2019-08-12 18:47:53 -04:00
Hannes Schmelzer
60df809f62 board/BuR/brsmarc1: initial commit
This commit adds support for the B&R brsmarc1 SoM.

The SoM is based on TI's AM335x SoC.
Mainly vxWorks 6.9.4.x is running on the board,
doing some PLC stuff on various carrier boards.

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2019-08-12 13:33:37 -04:00
Suniel Mahesh
6912f2a8ae watchdog: omap_wdt: Disable DM watchdog support in SPL
This patch disables DM watchdog support for SPL builds and uses
the legacy omap watchdog driver on TI AM335x chipsets.

The following build error is reported if DM watchdog support was
enabled in SPL:

  CC      spl/drivers/usb/gadget/rndis.o
  LD      spl/drivers/usb/gadget/built-in.o
  LD      spl/drivers/usb/musb-new/built-in.o
  LD      spl/drivers/built-in.o
  LD      spl/u-boot-spl
arm-linux-ld.bfd: u-boot-spl section .u_boot_list will not fit in region .sram
arm-linux-ld.bfd: region .sram overflowed by 440 bytes
make[1]: *** [spl/u-boot-spl] Error 1
make: *** [spl/u-boot-spl] Error 2

Adjusted WATCHDOG_RESET macro accordingly. Earlier it was pointing
to hw_watchdog_reset. Since CONFIG_WATCHDOG replaces CONFIG_HW_WATCHDOG,
now WATCHDOG_RESET macro points to watchdog_reset. This watchdog_reset
is not defined anywhere for am33xx/omap2 and needs to be defined. Fixed
this by simply calling hw_watchdog_reset in watchdog_reset.

Built and tested on AM335x device (BeagleboneBlack), compile tested for
all other AM33xx/omap2 based boards.

Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
[trini: Fix watchdog.h logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-12 13:27:55 -04:00
Simon Glass
e7dcf5645f env: Drop environment.h header file where not needed
This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.

Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2019-08-11 16:43:41 -04:00
Simon Glass
9fb625ce05 env: Move env_set() to env.h
Move env_set() over to the new header file.

Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2019-08-11 16:43:41 -04:00
Sam Protsenko
4347b0b0b2 omap: Correct the fastboot product var
"fastboot flashall" expects "fastboot getvar product" value to be one of
values provided in android-info.txt file (in AOSP), from "require
board=" list. Before this patch, "am57xx" is returned for all AM57xx
based boards, as it's set in $board env var from SYS_BOARD in
board/ti/am57xx/Kconfig file, which is used for default implementation
of "fastboot getvar product".

In order to fix that inconsistency, let's do next:
  1. In U-Boot: override fastboot.product, reusing the value from
     $board_name
  2. In AOSP: provide values for all AM57xx boards we can use to
     device/ti/beagle_x15/board-info.txt file

This way requirements check in "fastboot flashall" will work as
expected, verifying that user tries to flash images to the board which
those images were built for.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Acked-by: Andrew F. Davis <afd@ti.com>
2019-07-31 13:08:07 -04:00
Bartosz Golaszewski
e809285d49 net: davinci_emac: convert to using the driver model
Now that we removed all legacy boards selecting TI_EMAC we can
completely convert the driver code to using the driver model.
This patch also updates all remaining users of davinci_emac.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Adam Ford <aford173@gmail.com> #am3517-evm & da850-evm
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2019-07-25 13:36:13 -05:00
Tom Rini
2a51e16bd5 configs: Make USE_TINY_PRINTF depend on SPL||TPL and be default
The USE_TINY_PRINTF symbol only changes things within SPL and TPL
builds, so make it depend on that support.  Next, make it default as
within these cases we should rarely have need of more advanced print
formats outside of the debug context.

To do this, in a few cases we need to correct our Kconfig dependencies
as we had cases of non-SPL targets select'ing this symbol.  Finally, in
the case of a few boards we really do need the full printf
functionality.

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-07-13 11:11:29 -04:00
Niel Fourie
6e171b661e ARM: am335x: Add phyCORE AM335x R2 support
Support for Phytech phyCORE AM335x R2 SOM (PCL060) on the Phytec
phyBOARD-Wega AM335x.

CPU  : AM335X-GP rev 2.1
Model: Phytec AM335x phyBOARD-WEGA
DRAM:  256 MiB
NAND:  256 MiB
MMC:   OMAP SD/MMC: 0
eth0: ethernet@4a100000

Working:
 - Eth0
 - i2C
 - MMC/SD
 - NAND
 - UART
 - USB (host)

Device trees were taken from Linux mainline:
commit 37624b58542f ("Linux 5.1-rc7")

Signed-off-by: Niel Fourie <lusus@denx.de>
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Marek Vasut <marex@denx.de>
2019-07-13 11:11:28 -04:00
Marek Vasut
b2a2bf41ac arm: mach-omap2: am33xx: Init pinmux before clock
The board_early_init_f() inits clock before initing pinmux. However,
the clock configuration code might need to adjust PMIC settings of a
PMIC on I2C bus (e.g. board/ti/am335x/board.c does that). If the I2C
bus pin muxing is not configured before attempting to communicate
with the PMIC, the communication will silently fail and the prcm_init()
may configure fast enough CPU clock that the default voltage provided
by the PMIC would be insufficient and the platform would become
unstable.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Tom Rini <trini@konsulko.com>
2019-07-11 14:11:20 -04:00
Adam Ford
33ac2b560b arm: omap3: Manually initialize GPIO if OF_CONTROL doesn't
The commong initialization code manually initializes the GPIO
even when OF_CONTROL does it, so we can reduce the code size a
bit by not doing it manually when we have device tree support.

Using the omap3_logic board (dm3730), the sizes shrunk:

Before:

   text	   data	    bss	    dec	    hex	filename
 561066	  28596	 116880	 706542	  ac7ee	u-boot
  55245	   1605	   1888	  58738	   e572	spl/u-boot-spl

After
  text	   data	    bss	    dec	    hex	filename
 560898	  28548	 116872	 706318	  ac70e	u-boot
  55121	   1557	   1888	  58566	   e4c6	spl/u-boot-spl

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-06-05 12:14:02 -04:00
Bartosz Golaszewski
d7cc0e4d79 mcx: remove board
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-05-28 13:58:06 -04:00
Bartosz Golaszewski
2aa20c43e4 twister: remove board
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2019-05-28 13:58:06 -04:00
Bartosz Golaszewski
899dd71e9f mt_ventoux: remove board
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2019-05-28 13:58:06 -04:00
Bartosz Golaszewski
8c2644ca69 cm_t3517: remove board
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-05-28 13:58:06 -04:00
Bartosz Golaszewski
5e92c6856b eco5pk: remove board
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-05-28 13:58:06 -04:00
Trevor Woerner
1001502545 CONFIG_SPL_SYS_[DI]CACHE_OFF: add
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.

Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-05-18 08:15:35 -04:00