RK3568 has two USB 2.0 PHYs, and each PHY has two ports, the OTG port
of PHY0 support OTG mode with charging detection function, they are
similar to previous Rockchip SoCs.
However, there are three different designs for RK3568 USB 2.0 PHY.
1. RK3568 uses independent USB GRF module for each USB 2.0 PHY.
2. RK3568 accesses the registers of USB 2.0 PHY IP directly by APB.
3. The two ports of USB 2.0 PHY share one interrupt.
This patch only PHY1 with necessary attributes required to function
USBPHY1 on U-Boot.
Co-developed-by: Ren Jianing <jianing.ren@rock-chips.com>
Signed-off-by: Ren Jianing <jianing.ren@rock-chips.com>
Co-developed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
New Rockchip devices have the usb phy nodes as standalone devices.
These nodes have register nodes with #address_cells = 2, but only
use 32 bit addresses.
Adjust the driver to check if the returned address is "0", and adjust
the index in that case.
Derived and adjusted the similar change from linux-next with below
commit <9c19c531dc98> ("phy: phy-rockchip-inno-usb2: support
#address_cells = 2")
Co-developed-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa Compute Module 3(CM3) IO board an application board from Radxa
and is compatible with Raspberry Pi CM4 IO form factor.
Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.
Add support for Radxa CM3 IO Board defconfig and -u-boot.dtsi
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Radxa Compute Module 3(CM3) IO board an application board from Radxa
and is compatible with Raspberry Pi CM4 IO form factor.
Specification:
- 1x HDMI,
- 2x MIPI DSI
- 2x MIPI CSI2
- 1x eDP
- 1x PCIe card
- 2x SATA
- 2x USB 2.0 Host
- 1x USB 3.0
- 1x USB 2.0 OTG
- Phone jack
- microSD slot
- 40-pin GPIO expansion header
- 12V DC
Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.
linux-next commit for the same,
commit <8f19828844f2> ("arm64: dts: rockchip: Fix compatible for Radxa
CM3")
Add support for Radxa CM3 IO Board.
Co-developed-by: FUKAUMI Naoki <naoki@radxa.com>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Co-developed-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa Compute Module 3(CM3) is one of the modules from a series
System On Module based on the Radxa ROCK 3 series and is compatible
with Raspberry Pi CM4 pinout and form factor.
Specification:
- Rockchip RK3566
- up to 8GB LPDDR4
- up to 128GB high performance eMMC
- Optional wireless LAN, 2.4GHz and 5.0GHz IEEE 802.11b/g/n/ac wireless,
BT 5.0, BLE with onboard and external antenna.
- Gigabit Ethernet PHY
Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.
Since Radxa CM3 is compatible with Raspberry Pi CM4 pinout so it is
possible to mount Radxa CM3 on top of the Rasberry Pi CM4 IO board.
linux-next commit for the same,
commit <8f19828844f2> ("arm64: dts: rockchip: Fix compatible for Radxa
CM3")
Add support for Radxa CM3.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Co-developed-by: FUKAUMI Naoki <naoki@radxa.com>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Sync rockchip,vop2.h from linux-next, and the last commit is
commit <604be85547ce> ("drm/rockchip: Add VOP2 driver")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Like other rockchip SoCs, DM_RESET is useful across rk3568
platform.
Select it from arch kconfig.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The board should be RV1126-NEU2 instead RV1126-ECM0.
Fix the wrong name.
Fixes: b8f1ca9540 ("board: rockchip: Add Edgeble Neu2 IO Board")
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add default memory addresses for kernel_comp_addr_r and kernel_comp_size
to enable booting from a compressed kernel image. This area is temporarily
used to decompress the kernel image on-the-fly.
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add Radxa ROCK 3 Model A support. sync rk3308-rock-pi-s.dts from
Linux 6.2.0-rc7.
ROCK Pi S is RK3308 based SBC from radxa.com. ROCK Pi S has a,
- 256MB/512MB DDR3 RAM
- SD, NAND flash (optional on board 1/2/4/8Gb)
- 100MB ethernet, PoE (optional)
- Onboard 802.11 b/g/n wifi + Bluetooth 4.0 Module
- USB2.0 Type-A HOST x1
- USB3.0 Type-C OTG x1
- 26-pin expansion header
- USB Type-C DC 5V Power Supply
Linux commit commit for the same,
<2e04c25b1320> ("arm64: dts: rockchip: add ROCK Pi S DTS support")
Signed-off-by: Akash Gajjar <gajjar04akash@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add Radxa ROCK 3 Model A support. sync rk3568-rock-3a.dts from Linux 6.2.0-rc7
Board Specifications
- Rockchip RK3568
- 2/4/8GB LPDDR4 3200MT/s
- eMMC socket, SD card slot
- GbE LAN
- PCIe 3.0/2.0
- M.2 Connector
- 3.5mm Audio jack with mic
- HDMI 2.0, MIPI DSI/CSI
- USB 3.0 Host/OTG, USB 2.0 Host
- 40-pin GPIO expansion ports
- USB Type C PD 2.0, 9V/2A, 12V/2A, 15V/2A, 20V/2A
Refer Linux commit <22a442e6586c>
("arm64: dts: rockchip: add basic dts for the radxa rock3 model a")
Signed-off-by: Akash Gajjar <gajjar04akash@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Using the mkimage entry with the multiple-data-files prop and having a
missing external blob result in an unexpected ValueError exception using
the --allow-missing flag.
ValueError: Filename 'missing.bin' not found in input path (...)
Fix this by using _pathname that is resolved by ObtainContents for blob
entries, ObtainContents also handles allow missing for external blobs.
Mark mkimage entry as missing and return without running mkimage when
missing entries is reported by CheckMissing.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The current init size limit of 76KiB is too big to fit in the 64KiB SRAM
on RK3568, sync init size limit from vendor u-boot to fix this.
Set init size limit to 60KiB (-16KiB) for RK3568.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Latest vendor TPL for RK3328 has grown past the current init size limit
of 28KiB, sync the init size limit from vendor u-boot to fix this.
Set init size limit to 30KiB (+2KiB) for RK3328.
This makes it possible to use latest vendor TPL on RK3328 without
getting a size limit error running the mkimage command.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
An external TPL binary is now expected to be provided using ROCKCHIP_TPL
when building RK3568 targets.
This reverts commit 31500e7bcf.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip SoCs typically use U-Boot TPL to initialize DRAM, then jumps
back to BootRom to load next stage, U-Boot SPL, into DRAM. BootRom then
jumps to U-Boot SPL to continue the normal boot flow.
However, there is no support to initialize DRAM on RK35xx SoCs using
U-Boot TPL and instead an external TPL binary must be used to generate a
bootable u-boot-rockchip.bin image.
Add CONFIG_ROCKCHIP_EXTERNAL_TPL to indicate that an external TPL should
be used. Build U-Boot with ROCKCHIP_TPL=/path/to/ddr.bin to generate a
bootable u-boot-rockchip.bin image for RK3568.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Eugen Hristev <eugen.hristev@collabora.com>
The rockchip-tpl entry can be used when an external TPL binary should be
used instead of the normal U-Boot TPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Eugen Hristev <eugen.hristev@collabora.com>
The rk3328 sdram driver read sdram parameters from the devicetree into a
struct rk3328_sdram_params using dev_read_u32_array.
After commit 5ab30c3176 ("ram: rockchip: Update ddr pctl regs for px30")
changed the size of struct ddr_pctl_regs, a member of struct
rk3328_sdram_params, U-Boot TPL can no longer initialize DRAM on RK3328.
Add ten u32 to the sdram parameter array in devicetree to align with
this size change. This fixes DRAM initialization on RK3328.
Fixes: 5ab30c3176 ("ram: rockchip: Update ddr pctl regs for px30")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # roc-rk3328-cc
Add a second dram bank of usable memory beyond the blob of space for
peripheral near 4GB. Any memory that exists beyond the 4GB mark is added
to the second bank.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Newer DRAM initialization blobs from vendor can encode sdram info in a
new version 3 format. The new format makes use of more bits in sys_reg3
compared to the version 2 format.
Add basic support for detecting the version 3 format and decoding the
high bits used for ddrtype.
This fixes decode of sdram size on my RK3568 boards that have LPDDR4X.
Details on the new format was deciphered from vendor u-boot commit [1].
[1] c69667e0e2
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CONFIG_RAM_PX30_DDR4 got renamed to CONFIG_RAM_ROCKCHIP_DDR4 in commit
26f92be07e ("ram: rockchip: Add common ddr type configs"). Since both
patchsets were merged unbeknownst to the other, the conflict wasn't
detected while testing each patchset individually and could only be
observed after a merge to master branch.
Fixes: c925be73a0 ("rockchip: add support for PX30 Ringneck SoM on Haikou Devkit")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The RK3288 TRM states that, for 8-bit DDR modes:
The CLKDIV register should always be programmed with a value
higher than zero (0); that is, a clock divider should always be
used for 8-bit DDR mode.
In Linux, the driver applies this logic for all SoCs using the driver
and does not distinguish RK3288, so presumably this requirement is the
same for all other Rockchip SoCs using this IP.
Add the necessary code to double the clock frequency when 8-bit DDR is
selected. The dw_mmc core already handles setting CLKDIV correctly
given the input clock and desired bus clock.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Provide human-readable manufacturer and product names for the
FriendlyELEC NanoPi R4S.
Enable CONFIG_SYSINFO and CONFIG_SYSINFO_SMBIOS by default.
Signed-off-by: Christian Kohlschütter <christian@kohlschutter.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The PMC_MCK1 clock id for the ebi node is 23.
Fixes: 746b738224 ("ARM: dts: at91: sama7g5/sama7g5ek: align with Linux DT")
Reviewed-by: Eugen Hristev <eugen.hristev@collabora.com>
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
Add an implementation of this, moving the common call to tpm_init() up
into the common API implementation.
Add a test.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Currently there is only one test and it only works on TPM v2. Update it
to work on v1.2 as well, using a new function to pick up the required
TPM.
Update sandbox to include both a v1.2 and v2 TPM so that this works.
Split out the existing test into two pieces, one for init and one for
the v2-only report_state feature.
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
A prior patch adds a new API function for TPM2.0, which performs
the full startup sequence of the TPM. Add a selftest for that.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
All the TPM drivers as well as out TCG TIS API for a TPM2.0 device
return -EBUSY if the device has already been opened. Adjust
the sandbox TPM do return the same error code.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
A previous commit is adding a new tpm startup functions which
initializes the TPMv2 and performs all the needed selftests.
Since the TPM selftests might be needed depending on the requested
algorithm or functional module use that instead.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
As described in [0] if a command requires use of an untested algorithm
or functional module, the TPM performs the test and then completes the
command actions.
Since we don't check for TPM_RC_NEEDS_TEST (which is the return code of
the TPM in that case) and even if we would, it would complicate our TPM
code for no apparent reason, add a wrapper function that performs both
the selftest and the startup sequence of the TPM.
It's worth noting that this is implemented on TPMv2.0. The code for
1.2 would look similar, but I don't have a device available to test.
[0]
https://trustedcomputinggroup.org/wp-content/uploads/TPM-Rev-2.0-Part-1-Architecture-01.07-2014-03-13.pdf
§12.3 Self-test modes
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
I had added this line locally, rebuild the image, but didn't ensure that
I had committed the correct version of the patch as well.
Fixes: 75b031ee4a ("Dockerfile: download binaries for Nokia RX-51")
Signed-off-by: Tom Rini <trini@konsulko.com>
The "nand chip.erase" command always printed as bad blocks even in the
case of reserved blocks. Reserved blocks are used for storing bad block
tables. The patch displays "bbt reserved" when printing reserved blocks in
"nand chip.erase" command.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
In case ID is not found in manufacturer table, the raw ID is
printed using %*phN format which is not supported by lib/vsprintf.c.
The information displayed doesn't reflect the raw ID return by the
unknown spi-nand.
Use %02x format instead, as done in spi-nor-core.c.
For example, before this patch:
ERROR: spi-nand: spi_nand flash@0: unknown raw ID f74ec040
after
ERROR: spi-nand: spi_nand flash@0: unknown raw ID 00 c2 26 03
Fixes: 0a6d6bae03 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Hamming ECC doesn't cover the OOB data, so reading or writing OOB shall
always be done without ECC enabled.
This is a problem when adding JFFS2 cleanmarkers to erased blocks. If JFFS2
clenmarkers are added to the OOB with ECC enabled, OOB bytes will be changed
from ff ff ff to 00 00 00, reporting incorrect ECC errors.
Fixes: 27c5b17cd1b1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210224080210.23686-1-noltari@gmail.com
[Ported to U-Boot from the Linux kernel]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Only v3.3-v5.0 have a different CS0 layout.
Controllers before v3.3 use the same layout for every CS.
Fixes: 27c5b17cd1b1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200522121524.4161539-3-noltari@gmail.com
[Ported to U-Boot from the Linux kernel]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
These registers are also used on v3.3.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200522121524.4161539-2-noltari@gmail.com
[Ported to U-Boot from the Linux kernel]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
The current code checks that the whole OOB area is erased.
This is a problem when JFFS2 cleanmarkers are added to the OOB, since it will
fail due to the usable OOB bytes not being 0xff.
Correct this by only checking that data and ECC bytes aren't 0xff.
Fixes: 02b88eea9f9c ("mtd: brcmnand: Add check for erased page bitflips")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200512082451.771212-1-noltari@gmail.com
[Ported to U-Boot from the Linux kernel]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
This change adds support for flash dma v0.0.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[Ported to U-Boot from the Linux kernel]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
In brcmstb_nand_verify_erased_page(), the ECC chunk pointer calculation
while correcting erased page bitflips is wrong, fix it.
Fixes: 02b88eea9f9c ("mtd: brcmnand: Add check for erased page bitflips")
Signed-off-by: Claire Lin <claire.lin@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[Ported to U-Boot from the Linux kernel]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
This change adds support for brcm NAND v7.3 controller. This controller
uses a newer version of flash_dma engine and change mostly implements
these differences.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[Ported to U-Boot from the Linux kernel]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Refactored NAND ECC and CMD address configuration code to use helper
functions.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[Ported to U-Boot from the Linux kernel]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reserved blocks are used for storing bad block tables. With "nand bad"
command, these reserved blocks are shown as bad blocks. This is leading
to confusion when compared with Linux bad blocks. Hence, display
"bbt reserved" when printing reserved blocks with "nand bad" command.
To acheive this, return 2 which represents reserved from nand_isbad_bbt()
instead of 1 in case of reserved blocks and catch it in cmd/nand.c.
"nand bad" command display's hexadecimal numbers, so add "0x" prefix.
Example log will show up as below.
ZynqMP> nand bad
Device 0 bad blocks:
0x00400000
0x16800000
0x16c00000
0x17000000
0x3d800000
0x3e400000
0xe8400000
0xff000000 (bbt reserved)
0xff400000 (bbt reserved)
0xff800000 (bbt reserved)
0xffc00000 (bbt reserved)
0x116800000
0x116c00000
0x1ff000000 (bbt reserved)
0x1ff400000 (bbt reserved)
0x1ff800000 (bbt reserved)
0x1ffc00000 (bbt reserved)
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-By: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
- Merge in changes to our Dockerfile so that we build and download ahead
of time all of the components required to run the nx51 test scripts.
This will both speed up the specific job and address failures in Azure
where the ipk files fail to download.
